Hi all,
I?m using X-Lite as SoftPhone in Asterisk. I have configured this:
[101]
;Turn off silence suppression in X-Lite ("Transmit Silence"=YES)!
;Note that Xlite sends NAT keep-alive packets, so qualify=yes is not needed
type=friend
username=jozeph
callerid="Jozeph Brasil" <5678>
host=dynamic
nat=yes ; X-Lite is behind a NAT router
canreinvite=no ; Typically set to NO if behind NAT
;disallow=all
allow=gsm ; GSM consumes far less bandwidth than ulaw
;allow=ulaw
;allow=alaw
When I try to connect X-Lite from another network follow this model:
WORK (192.168.1.X) <-- --> FW-NAT <-- --> INTERNET <-- -->
ASTERISK SERVER
That machine connect OK!
But, when I try to connect using this model:
WORK (10.0.0.X) <-- --> 10.0.0.254 (ASTERISK SERVER)
I can?t connect to the server.... why that?
Asterisk Server have 2 network cards... internal and external internet card.
My SIP.CONF are listen 0.0.0.0.
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
http://lists.digium.com/pipermail/asterisk-users/attachments/20040725/51984d49/attachment.htm
Hello, I've recently purchased Adit 600 with 3FXS and 1FXO to be connected to my * server via T100P card. This is the output of "status equipment" command in the Adit600: For some reason the FXO card is seen as FXS, why? Is it ok? On the card it is written "FXO". Regards, Shlomi Bachar -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040725/1b981676/attachment.htm
Shlomi Bachar wrote:> I?ve recently purchased Adit 600 with 3FXS and 1FXO to be connected to > my * server via T100P card. This is the output of ?status equipment? > command in the Adit600: > > For some reason the FXO card is seen as FXS, why? Is it ok? On the card > it is written ?FXO?. >I would ask ADIT, not the mailing list for a PBX. You could also, you know, TRY it. -- Daniel Jimenez <djimenez[at]pobox[dot]com>
Here is the output of the "status equipment" command :
BootCode Version: 1.23
CardType Status SW Vers CLEI
-------- ------ ------- ----
SLOT A T1x2 Present 6.1.2 SIC3DH0CAA
SLOT 1 FXSx8 Present 1.09 SIC3GJ0CAA
SLOT 2 FXSx8 Present 1.09 SIC3GJ0CAA
SLOT 3 FXS5Gx8 Present 1.10 SIC2780JAA
SLOT 4 FXSx8 Present 1.09 SIC3GJ0CAA
SLOT 5 FXSx8 Not Present
SLOT 6 V35x2 Not Present
- Shlomi
-----Original Message-----
From: asterisk-users-admin@lists.digium.com
[mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Shlomi
Bachar
Sent: Sunday, July 25, 2004 4:23 PM
To: asterisk-users@lists.digium.com
Subject: [Asterisk-Users] FXS vs. FXO
Hello,
I've recently purchased Adit 600 with 3FXS and 1FXO to be connected to
my * server via T100P card. This is the output of "status equipment"
command in the Adit600:
For some reason the FXO card is seen as FXS, why? Is it ok? On the card
it is written "FXO".
Regards,
Shlomi Bachar
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
http://lists.digium.com/pipermail/asterisk-users/attachments/20040725/cecc8492/attachment.htm