( Replying to xen-users instead of old sourceforge list. )
On Mon, 2005-04-18 at 17:53 +0100, Ian Pratt wrote:> > Initially I made some progress with the pre-built kernel
> > binaries (from the current 2.0.5 release). The xenU kernel
> > lacks PCI support, and X reports "Cannot open /dev/tty0"
> > using it in domain 1. I switched to the xen0 kernel for PCI
> > support, and then X reported "Cannot find a free VT".
> >
> > The output from lspci lists everything but the VGA card in
> > domain 0, unless "lspci -H 1" is used. In other domains,
> > lspci reports only the VGA card and "lspci -H 1" reports
"You
> > need to be root to have access to I/O ports". However X
> > still starts OK in domain 0, which surprised my.
> > I''ve confirmed that "xm dmesg" includes
"Hiding PCI device
> > 01:00.0 from DOM0" after passing
"physdev_dom0_hide=01:00.1" to Xen.
>
> I can see how you could start a very simple VGA-only Xserver -- by
> default dom0 happens to have access to the bottom 1MB of memory, which
> is enough to get a VGA Xserver working.
OK, I wasn''t familiar with this. However I''ve checked
XFree86.0.log
from domain 0 for memory reports, and these two lines indicate more than
1MB is available, which may be a problem:
(II) SIS(0): Using 15808K of framebuffer memory
...
(II) SIS(0): VESA VBE Total Mem: 16384 kB
> > I''ve followed Ian''s advice, rebuilding Linux 2.6.10
with the
> > default xenU configuration eith XEN_PHSDEV_ACCESS added (to
> > automatically enable
> > DUMMY_CONSOLE) plus PCI support. However my kernel crashes
> > immediately after "Freeing unused kernel memory", even when
I
> > pass "xencons=ttyS".
> > Perhaps the build broke somehow, or it''s configuration is
invalid?
>
> I think you''ll need to look through the oops message to see
what''s going
> on.
I''ve included a relevant section below - I could post the whole output
as a gzip attachment if it would help?
> You could try setting xencons=off just to rule xencons out.
The domain still exits, albeit silently without console output. However
I have found that I need the suggested "xencons=ttyS" to avoid an
additional line of kernel output "Warning: unable to open an initial
console".
> I presume you''ve granted the PCI device to the other domain in
it''s
> config file?
I hoped that the line "pci = [ ''01,00,00'' ]" in my
previous post was
sufficient?
Cheers,
Sean.
Xen console output section from new domain:
Oops: 0000 [#1]
PREEMPT
Modules linked in:
CPU: 0
EIP: 0061:[<c0227a02>] Not tainted VLI
EFLAGS: 00010246 (2.6.10xenU-mod)
EIP is at visual_init+0x72/0x1c0
eax: 00000000 ebx: c00e6e00 ecx: 00000000 edx: c00e6e00
esi: 00000000 edi: 00000001 ebp: 00000000 esp: c0023e94
ds: 007b es: 007b ss: 0069
Process init (pid: 1, threadinfo=c0022000 task=c03b69e0)
Stack: 00000000 000000d0 c00e6e00 00000000 c0227bf1 00000000 00000001
00000000
c00c9bc0 00000000 00000000 c1365000 00400000 c022b1e8 00000000
ffffffed
c00dab80 00000001 c021aa6d c1365000 c00dab80 c0023ef0 00000102
c1365000
Call Trace:
[<c0227bf1>] vc_allocate+0xa1/0x1b0
[<c022b1e8>] con_open+0x48/0xc0
[<c021aa6d>] tty_open+0x24d/0x2d0
[<c021a820>] tty_open+0x0/0x2d0
[<c015e96a>] chrdev_open+0xea/0x1d0
[<c0343324>] free_area_init_core+0xb4/0x300
[<c0343324>] free_area_init_core+0xb4/0x300
[<c015486a>] dentry_open+0x15a/0x240
[<c0343324>] free_area_init_core+0xb4/0x300
[<c0154708>] filp_open+0x68/0x70
[<c0154989>] get_unused_fd+0x39/0xe0
[<c0154af9>] sys_open+0x49/0x90
[<c0109658>] syscall_call+0x7/0xb
Code: 40 6d 36 c0 a1 2c 6d 36 c0 89 42 28 8b 14 b5 80 7e 36 c0 85 d2 74
0a 8b 04 b5 40 6d 36 c0 89 50 28 8b 14 b5 40 6d 36 c0 8b 42 28 <8b> 18
85 db 74 35 89 1c 24 e8 80 8c f0 ff 85 c0 0f 84 09 01 00
<0>Kernel panic - not syncing: Attempted to kill init!
<0>Rebooting in 1 seconds..
--
Sean Atkinson <sean@netproject.com>
Netproject
_______________________________________________
Xen-users mailing list
Xen-users@lists.xensource.com
http://lists.xensource.com/xen-users