It works fine. Thank you once again root@ServerXen331:/usr/src# mkdir linux.trees.git || exit -1 root@ServerXen331:/usr/src# cd linux.trees.git root@ServerXen331:/usr/src/linux.trees.git# git init Initialized empty Git repository in /usr/src/linux.trees.git/.git/ root@ServerXen331:/usr/src/linux.trees.git# git remote add linus git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git root@ServerXen331:/usr/src/linux.trees.git# git remote add tip git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git root@ServerXen331:/usr/src/linux.trees.git# git remote update Updating linus warning: no common commits remote: Counting objects: 1068144, done. remote: Compressing objects: 100% (178196/178196), done. remote: Total 1068144 (delta 890175), reused 1062206 (delta 885050) Receiving objects: 100% (1068144/1068144), 258.76 MiB | 26 KiB/s, done. Resolving deltas: 100% (890175/890175), done. . . . . . . . . . . Updating tip remote: Counting objects: 19569, done. remote: Compressing objects: 100% (7482/7482), done. remote: Total 18172 (delta 14981), reused 12843 (delta 10122) Receiving objects: 100% (18172/18172), 3.54 MiB | 107 KiB/s, done. Resolving deltas: 100% (14981/14981), completed with 1157 local objects.>From git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen* [new branch] acpi/map -> tip/acpi/map * [new branch] mainline/mm -> tip/mainline/mm * [new branch] mainline/net -> tip/mainline/net * [new branch] master -> tip/master * [new branch] push/xen/dom0/core -> tip/push/xen/dom0/core * [new branch] tip/fixups -> tip/tip/fixups * [new branch] x86/apic -> tip/x86/apic * [new branch] x86/cpa -> tip/x86/cpa * [new branch] x86/unify -> tip/x86/unify * [new branch] x86/unify-base -> tip/x86/unify-base * [new branch] x86/unify-irq -> tip/x86/unify-irq * [new branch] x86/unify-irq-base -> tip/x86/unify-irq-base * [new branch] x86/unify-kmemcheck -> tip/x86/unify-kmemcheck * [new branch] x86/unify-kmemcheck-base -> tip/x86/unify-kmemcheck-base * [new branch] x86/untangle -> tip/x86/untangle * [new branch] x86/untangle2 -> tip/x86/untangle2 * [new branch] xen/core -> tip/xen/core * [new branch] xen/dev-evtchn -> tip/xen/dev-evtchn * [new branch] xen/dom0/apic -> tip/xen/dom0/apic * [new branch] xen/dom0/backend/blkback -> tip/xen/dom0/backend/blkback * [new branch] xen/dom0/backend/core -> tip/xen/dom0/backend/core * [new branch] xen/dom0/backend/netback -> tip/xen/dom0/backend/netback * [new branch] xen/dom0/core -> tip/xen/dom0/core * [new branch] xen/dom0/hackery -> tip/xen/dom0/hackery * [new branch] xen/dom0/mtrr -> tip/xen/dom0/mtrr * [new branch] xen/dom0/pci -> tip/xen/dom0/pci * [new branch] xen/dom0/swiotlb -> tip/xen/dom0/swiotlb * [new branch] xen/dom0/xenfs -> tip/xen/dom0/xenfs * [new branch] xen/frontend/blkfront -> tip/xen/frontend/blkfront * [new branch] xen/fs -> tip/xen/fs * [new branch] xen/hg-queue-import -> tip/xen/hg-queue-import * [new branch] xen/irq -> tip/xen/irq * [new branch] xen/master -> tip/xen/master * [new branch] xen/pvhvm -> tip/xen/pvhvm * [new branch] xen/xenbus -> tip/xen/xenbus . . . . . . root@ServerXen331:/usr/src/linux.trees.git# git checkout -b xen-latest tip/xen/dom0/hackery warning: You appear to be on a branch yet to be born. warning: Forcing checkout of tip/master. Checking out files: 100% (26687/26687), done. Branch tip-latest set up to track remote branch refs/remotes/tip/master. Switched to a new branch "xen-latest" make menuconfig # Activate Xen Dom0 support make make modules_install install Already loaded under Xen-Unstable and tested via Solaris Nevada 106 PV DomU installation. _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
On Tue, Feb 17, 2009 at 03:58:45AM -0800, Boris Derzhavets wrote:> > It works fine. > Thank you once again >What kind of hardware are you running on? Which disk controller? 64-bit hypervisor/dom0 or 32-bit PAE? Would you like to send your dom0 kernel .config ? And your grub.conf .. Thanks! Nice to hear you got it running/working! -- Pasi _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Hardware config:- C2D E8400, 8 GB RAM, ASUS P5K Premium/WIFI (Intel P35+Intel ICH9R), 2x250 SATA Seagate Barracuda (no RAID). Bios settings for ICH9R - AHCI. Details here:- http://bderzhavets.wordpress.com/2009/02/17/setup-xen-unstable-dom0-via-2629-rc5-pv_ops-enabled-kernel-on-intel-sataahci/ --- On Tue, 2/17/09, Pasi Kärkkäinen <pasik@iki.fi> wrote: From: Pasi Kärkkäinen <pasik@iki.fi> Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip To: "Boris Derzhavets" <bderzhavets@yahoo.com> Cc: "Ian Campbell" <Ian.Campbell@eu.citrix.com>, "Jeremy Fitzhardinge" <jeremy@goop.org>, "xen-devel@lists.xensource.com" <xen-devel@lists.xensource.com> Date: Tuesday, February 17, 2009, 8:11 AM On Tue, Feb 17, 2009 at 03:58:45AM -0800, Boris Derzhavets wrote:> > It works fine. > Thank you once again >What kind of hardware are you running on? Which disk controller? 64-bit hypervisor/dom0 or 32-bit PAE? Would you like to send your dom0 kernel .config ? And your grub.conf .. Thanks! Nice to hear you got it running/working! -- Pasi _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
On Tue, Feb 17, 2009 at 05:31:57AM -0800, Boris Derzhavets wrote:> Hardware config:- > C2D E8400, 8 GB RAM, ASUS P5K Premium/WIFI (Intel P35+Intel ICH9R), > 2x250 SATA Seagate Barracuda (no RAID). Bios settings for ICH9R - AHCI. > Details here:- > http://bderzhavets.wordpress.com/2009/02/17/setup-xen-unstable-dom0-via-2629-rc5-pv_ops-enabled-kernel-on-intel-sataahci/ >Thanks! So it seems you''re running 64 bit dom0 OS/hypervisor.. 64 bit seems to work better atm than 32 bit.. -- Pasi> > --- On Tue, 2/17/09, Pasi Kärkkäinen <pasik@iki.fi> wrote: > From: Pasi Kärkkäinen <pasik@iki.fi> > Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip > To: "Boris Derzhavets" <bderzhavets@yahoo.com> > Cc: "Ian Campbell" <Ian.Campbell@eu.citrix.com>, "Jeremy Fitzhardinge" <jeremy@goop.org>, "xen-devel@lists.xensource.com" <xen-devel@lists.xensource.com> > Date: Tuesday, February 17, 2009, 8:11 AM > > On Tue, Feb 17, 2009 at 03:58:45AM -0800, Boris Derzhavets wrote: > > > > It works fine. > > Thank you once again > > > > What kind of hardware are you running on? Which disk controller? > > 64-bit hypervisor/dom0 or 32-bit PAE? > > Would you like to send your dom0 kernel .config ? > > And your grub.conf .. > > Thanks! > > Nice to hear you got it running/working! > > -- Pasi > >_______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Marc - A. Dahlhaus [ Administration | Westermann GmbH ]
2009-Feb-17 14:09 UTC
Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip
Hello Boris, with git >= v1.5 you can get to the right branch even simpler with: git clone git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git linux-2.6-xen cd linux-2.6-xen git checkout origin/xen/dom0/hackery -b xen/dom0/hackery To update: git pull Works like a charm here but i didn''t had the time to boottest it... Am Dienstag, den 17.02.2009, 05:31 -0800 schrieb Boris Derzhavets:> Hardware config:- > C2D E8400, 8 GB RAM, ASUS P5K Premium/WIFI (Intel P35+Intel ICH9R), > 2x250 SATA Seagate Barracuda (no RAID). Bios settings for ICH9R - > AHCI. > Details here:- > http://bderzhavets.wordpress.com/2009/02/17/setup-xen-unstable-dom0-via-2629-rc5-pv_ops-enabled-kernel-on-intel-sataahci/ > > > --- On Tue, 2/17/09, Pasi Kärkkäinen <pasik@iki.fi> wrote: > From: Pasi Kärkkäinen <pasik@iki.fi> > Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip > To: "Boris Derzhavets" <bderzhavets@yahoo.com> > Cc: "Ian Campbell" <Ian.Campbell@eu.citrix.com>, "Jeremy > Fitzhardinge" <jeremy@goop.org>, > "xen-devel@lists.xensource.com" > <xen-devel@lists.xensource.com> > Date: Tuesday, February 17, 2009, 8:11 AM > > On Tue, Feb 17, 2009 at 03:58:45AM -0800, Boris Derzhavets wrote: > > > > It works fine. > > Thank you once again > > > > What kind of hardware are you running on? Which disk controller? > > 64-bit hypervisor/dom0 or 32-bit PAE? > > Would you like to send your dom0 kernel .config ? > > And your grub.conf .. > > Thanks! > > Nice to hear you got it running/working! > > -- Pasi > > _______________________________________________ > Xen-devel mailing list > Xen-devel@lists.xensource.com > http://lists.xensource.com/xen-devel_______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Pasi Kärkkäinen wrote:> On Tue, Feb 17, 2009 at 05:31:57AM -0800, Boris Derzhavets wrote: > >> Hardware config:- >> C2D E8400, 8 GB RAM, ASUS P5K Premium/WIFI (Intel P35+Intel ICH9R), >> 2x250 SATA Seagate Barracuda (no RAID). Bios settings for ICH9R - AHCI. >> Details here:- >> http://bderzhavets.wordpress.com/2009/02/17/setup-xen-unstable-dom0-via-2629-rc5-pv_ops-enabled-kernel-on-intel-sataahci/ >> >> > > Thanks! > > So it seems you''re running 64 bit dom0 OS/hypervisor.. > > 64 bit seems to work better atm than 32 bit.. >I tend to focus on 64-bit, and Ian Campbell has been looking at 32-bit. In theory there shouldn''t be all that much difference between them. There have been a few issues, but they''re sharing 90+% of the code. (In practice I''m interested in any bug reports, esp comparing 32 and 64-bit behaviour). J _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Boris Derzhavets wrote:> It works fine. > Thank you once again > > root@ServerXen331:/usr/src# mkdir linux.trees.git || exit -1 > root@ServerXen331:/usr/src# cd linux.trees.git > root@ServerXen331:/usr/src/linux.trees.git# git init > Initialized empty Git repository in /usr/src/linux.trees.git/.git/ > root@ServerXen331:/usr/src/linux.trees.git# git remote add linus > git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git > root@ServerXen331:/usr/src/linux.trees.git# git remote add tip > git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git >This is a fairly misleading name, and I think you''ll just end up confusing yourself. "linux-2.6-tip.git" is a different git tree that''s upstream to xen.git, but distinct from it. You''d be better off calling this remote "xen". J _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Sorry, but it works. --- On Tue, 2/17/09, Jeremy Fitzhardinge <jeremy@goop.org> wrote: From: Jeremy Fitzhardinge <jeremy@goop.org> Subject: [Xen-devel] Re: Build vmlinuz-2.6.29-rc5-tip To: bderzhavets@yahoo.com Cc: "Ian Campbell" <Ian.Campbell@eu.citrix.com>, "xen-devel@lists.xensource.com" <xen-devel@lists.xensource.com> Date: Tuesday, February 17, 2009, 1:41 PM Boris Derzhavets wrote:> It works fine. > Thank you once again > root@ServerXen331:/usr/src# mkdir linux.trees.git || exit -1 > root@ServerXen331:/usr/src# cd linux.trees.git > root@ServerXen331:/usr/src/linux.trees.git# git init > Initialized empty Git repository in /usr/src/linux.trees.git/.git/ > root@ServerXen331:/usr/src/linux.trees.git# git remote add linusgit://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git> root@ServerXen331:/usr/src/linux.trees.git# git remote add tipgit://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git>This is a fairly misleading name, and I think you''ll just end up confusing yourself. "linux-2.6-tip.git" is a different git tree that''s upstream to xen.git, but distinct from it. You''d be better off calling this remote "xen". J _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Mark, I''ve just tried. Your procedure works grate. I will try to load kernel (under Xen Unstable) after patching per Jeremy. Thank you. Boris. P.S. root@ServerXen331:~# git --version git version 1.5.6.3 --- On Tue, 2/17/09, Marc - A. Dahlhaus [ Administration | Westermann GmbH ] <mad@wol.de> wrote: From: Marc - A. Dahlhaus [ Administration | Westermann GmbH ] <mad@wol.de> Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip To: bderzhavets@yahoo.com Cc: "xen-devel@lists.xensource.com" <xen-devel@lists.xensource.com> Date: Tuesday, February 17, 2009, 9:09 AM Hello Boris, with git >= v1.5 you can get to the right branch even simpler with: git clone git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git linux-2.6-xen cd linux-2.6-xen git checkout origin/xen/dom0/hackery -b xen/dom0/hackery To update: git pull Works like a charm here but i didn''t had the time to boottest it... Am Dienstag, den 17.02.2009, 05:31 -0800 schrieb Boris Derzhavets:> Hardware config:- > C2D E8400, 8 GB RAM, ASUS P5K Premium/WIFI (Intel P35+Intel ICH9R), > 2x250 SATA Seagate Barracuda (no RAID). Bios settings for ICH9R - > AHCI. > Details here:- >http://bderzhavets.wordpress.com/2009/02/17/setup-xen-unstable-dom0-via-2629-rc5-pv_ops-enabled-kernel-on-intel-sataahci/> > > --- On Tue, 2/17/09, Pasi Kärkkäinen <pasik@iki.fi> wrote: > From: Pasi Kärkkäinen <pasik@iki.fi> > Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip > To: "Boris Derzhavets" <bderzhavets@yahoo.com> > Cc: "Ian Campbell" <Ian.Campbell@eu.citrix.com>,"Jeremy> Fitzhardinge" <jeremy@goop.org>, > "xen-devel@lists.xensource.com" > <xen-devel@lists.xensource.com> > Date: Tuesday, February 17, 2009, 8:11 AM > > On Tue, Feb 17, 2009 at 03:58:45AM -0800, Boris Derzhavets wrote: > > > > It works fine. > > Thank you once again > > > > What kind of hardware are you running on? Which disk controller? > > 64-bit hypervisor/dom0 or 32-bit PAE? > > Would you like to send your dom0 kernel .config ? > > And your grub.conf .. > > Thanks! > > Nice to hear you got it running/working! > > -- Pasi > > _______________________________________________ > Xen-devel mailing list > Xen-devel@lists.xensource.com > http://lists.xensource.com/xen-devel_______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Hi Mark, I am done with kernel compiled per your advice. Xen Unstable Dom0 & 2.6.29-rc5 (Xen Dom0 support enabled) loaded fine. Thanks, Boris # dmesg [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.29-rc5-tip (root@ServerUbuntu) (gcc version 4.3.2 (Ubuntu 4.3.2-1ubuntu11) ) #2 SMP Wed Feb 18 12:14:04 EST 2009 [ 0.000000] Command line: root=/dev/sdb1 ro console=tty0 pci=nomsi [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] Centaur CentaurHauls [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: 0000000000000000 - 000000000009ec00 (usable) [ 0.000000] Xen: 000000000009ec00 - 0000000000100000 (reserved) [ 0.000000] Xen: 0000000000100000 - 000000000bc1d000 (usable) [ 0.000000] Xen: 000000000bc1d000 - 000000000be1e000 (reserved) [ 0.000000] Xen: 000000000be1e000 - 0000000040000000 (usable) [ 0.000000] Xen: 00000000cff80000 - 00000000cff8e000 (ACPI data) [ 0.000000] Xen: 00000000cff8e000 - 00000000cffe0000 (ACPI NVS) [ 0.000000] Xen: 00000000cffe0000 - 00000000d0000000 (reserved) [ 0.000000] Xen: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] Xen: 00000000ffe00000 - 0000000100000000 (reserved) [ 0.000000] DMI 2.4 present. [ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it. [ 0.000000] last_pfn = 0x40000 max_arch_pfn = 0x100000000 [ 0.000000] init_memory_mapping: 0000000000000000-0000000040000000 [ 0.000000] 0000000000 - 0040000000 page 4k [ 0.000000] kernel direct mapping tables up to 40000000 @ be81000-c083000 [ 0.000000] last_map_addr: 40000000 end: 40000000 [ 0.000000] RAMDISK: 008da000 - 0bc1ce00 [ 0.000000] ACPI: RSDP 000FBB80, 0014 (r0 ACPIAM) [ 0.000000] ACPI: RSDT CFF80000, 003C (r1 A_M_I_ OEMRSDT 10000730 MSFT 97) [ 0.000000] ACPI: FACP CFF80200, 0084 (r2 A_M_I_ OEMFACP 10000730 MSFT 97) [ 0.000000] FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4) [ 0.000000] ACPI: DSDT CFF805C0, 8E13 (r1 A0840 A0840001 1 INTL 20060113) [ 0.000000] ACPI: FACS CFF8E000, 0040 [ 0.000000] ACPI: APIC CFF80390, 006C (r1 A_M_I_ OEMAPIC 10000730 MSFT 97) [ 0.000000] ACPI: MCFG CFF80400, 003C (r1 A_M_I_ OEMMCFG 10000730 MSFT 97) [ 0.000000] ACPI: OEMB CFF8E040, 0081 (r1 A_M_I_ AMI_OEM 10000730 MSFT 97) [ 0.000000] ACPI: HPET CFF893E0, 0038 (r1 A_M_I_ OEMHPET 10000730 MSFT 97) [ 0.000000] ACPI: OSFR CFF89420, 00B0 (r1 A_M_I_ OEMOSFR 10000730 MSFT 97) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] (6 early reservations) ==> bootmem [0000000000 - 0040000000] [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] [ 0.000000] #1 [000be1e000 - 000be81000] XEN PAGETABLES ==> [000be1e000 - 000be81000] [ 0.000000] #2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] [ 0.000000] #3 [0000200000 - 00008d9d20] TEXT DATA BSS ==> [0000200000 - 00008d9d20] [ 0.000000] #4 [00008da000 - 000bc1ce00] RAMDISK ==> [00008da000 - 000bc1ce00] [ 0.000000] #5 [000be81000 - 000c01d000] PGTABLE ==> [000be81000 - 000c01d000] [ 0.000000] found SMP MP-table at [ffff8800000ff780] ff780 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal 0x00100000 -> 0x00100000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[3] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009e [ 0.000000] 0: 0x00000100 -> 0x0000bc1d [ 0.000000] 0: 0x0000be1e -> 0x00040000 [ 0.000000] On node 0 totalpages: 261517 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 1758 pages reserved [ 0.000000] DMA zone: 2168 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 3528 pages used for memmap [ 0.000000] DMA32 zone: 254007 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0xffffffff base: 0xfed00000 [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs [ 0.000000] nr_irqs_gsi: 24 [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:8ff80000) [ 0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1 [ 0.000000] PERCPU: Allocating 86016 bytes of per cpu data [ 0.000000] trying to map vcpu_info 0 at ffff88000c034020, mfn 21ffcc, offset 32 [ 0.000000] cpu 0 using vcpu_info at ffff88000c034020 [ 0.000000] trying to map vcpu_info 1 at ffff88000c049020, mfn 21ffb7, offset 32 [ 0.000000] cpu 1 using vcpu_info at ffff88000c049020 [ 0.000000] Xen: using vcpu_info placement [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 256175 [ 0.000000] Kernel command line: root=/dev/sdb1 ro console=tty0 pci=nomsi [ 0.000000] Initializing CPU#0 [ 0.000000] NR_IRQS:1280 [ 0.000000] xen: allocated irq 9 for acpi 9 [ 0.000000] xen_allocate_pirq: returning irq 9 for gsi 9 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 0.000000] Detected 3005.616 MHz processor. [ 0.010000] Console: colour VGA+ 80x25 [ 0.010000] console [tty0] enabled [ 0.010000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.010000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.010000] allocated 10485760 bytes of page_cgroup [ 0.010000] please try cgroup_disable=memory option if you don''t want [ 0.010000] Checking aperture... [ 0.010000] No AGP bridge found [ 0.010000] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.010000] xen_swiotlb_fixup: buf=ffff88000daa8000 size=67108864 [ 0.010000] xen_swiotlb_fixup: buf=ffff880011b08000 size=32768 [ 0.010000] Placing 64MB software IO TLB between ffff88000daa8000 - ffff880011aa8000 [ 0.010000] software IO TLB at phys 0xdaa8000 - 0x11aa8000 [ 0.010000] Memory: 760356k/1048576k available (3248k kernel code, 2508k absent, 285004k reserved, 1775k data, 456k init) [ 0.010000] Xen: using vcpuop timer interface [ 0.010000] installing Xen timer for CPU 0 [ 0.010000] Calibrating delay loop (skipped), value calculated using timer frequency.. 6011.23 BogoMIPS (lpj=30056160) [ 0.010000] Security Framework initialized [ 0.010000] SELinux: Disabled at boot. [ 0.010000] Mount-cache hash table entries: 256 [ 0.010000] Initializing cgroup subsys ns [ 0.010000] Initializing cgroup subsys cpuacct [ 0.010000] Initializing cgroup subsys memory [ 0.010000] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.010000] CPU: L2 cache: 6144K [ 0.010000] CPU: Physical Processor ID: 0 [ 0.010000] CPU: Processor Core ID: 0 [ 0.010000] SMP alternatives: switching to UP code [ 0.024292] ACPI: Core revision 20081204 [ 0.040082] cpu 0 spinlock event irq 25 [ 0.041292] installing Xen timer for CPU 1 [ 0.041344] cpu 1 spinlock event irq 31 [ 0.041410] SMP alternatives: switching to SMP code [ 0.000005] Initializing CPU#1 [ 0.000038] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.000041] CPU: L2 cache: 6144K [ 0.000044] CPU: Physical Processor ID: 0 [ 0.000046] CPU: Processor Core ID: 0 [ 0.077347] Brought up 2 CPUs [ 0.077593] CPU0 attaching sched-domain: [ 0.077596] domain 0: span 0-1 level CPU [ 0.077600] groups: 0 1 [ 0.077610] CPU1 attaching sched-domain: [ 0.077612] domain 0: span 0-1 level CPU [ 0.077616] groups: 1 0 [ 0.078184] net_namespace: 1840 bytes [ 0.078230] Booting paravirtualized kernel on Xen [ 0.078273] Xen version: 3.4-unstable (preserve-AD) (dom0) [ 0.078453] Grant table initialized [ 0.078519] Time: 17:25:51 Date: 02/18/09 [ 0.078614] NET: Registered protocol family 16 [ 0.079002] xenbus_probe_init ok [ 0.079309] ACPI: bus type pci registered [ 0.079875] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 [ 0.079923] PCI: Not using MMCONFIG. [ 0.079965] PCI: Using configuration type 1 for base access [ 0.082777] bio: create slab <bio-0> at 0 [ 0.085729] ACPI: EC: Look up EC in DSDT [ 0.100205] ACPI: Interpreter enabled [ 0.100249] ACPI: (supports S0 S1 S3 S5) [ 0.100433] ACPI: Using IOAPIC for interrupt routing [ 0.100533] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 [ 0.103872] PCI: MCFG area at e0000000 reserved in ACPI motherboard resources [ 0.165824] PCI: Using MMCONFIG at e0000000 - efffffff [ 0.181128] ACPI: No dock devices found. [ 0.181237] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.181565] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold [ 0.181614] pci 0000:00:01.0: PME# disabled [ 0.181799] pci 0000:00:1a.0: reg 20 io port: [0xa800-0xa81f] [ 0.181935] pci 0000:00:1a.1: reg 20 io port: [0xa880-0xa89f] [ 0.182070] pci 0000:00:1a.2: reg 20 io port: [0xac00-0xac1f] [ 0.182210] pci 0000:00:1a.7: reg 10 32bit mmio: [0xf9fffc00-0xf9ffffff] [ 0.182314] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold [ 0.182363] pci 0000:00:1a.7: PME# disabled [ 0.182482] pci 0000:00:1b.0: reg 10 64bit mmio: [0xf9ff8000-0xf9ffbfff] [ 0.182568] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold [ 0.182617] pci 0000:00:1b.0: PME# disabled [ 0.182773] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.182822] pci 0000:00:1c.0: PME# disabled [ 0.182987] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold [ 0.183036] pci 0000:00:1c.4: PME# disabled [ 0.183195] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold [ 0.183244] pci 0000:00:1c.5: PME# disabled [ 0.183389] pci 0000:00:1d.0: reg 20 io port: [0xa080-0xa09f] [ 0.183528] pci 0000:00:1d.1: reg 20 io port: [0xa400-0xa41f] [ 0.183663] pci 0000:00:1d.2: reg 20 io port: [0xa480-0xa49f] [ 0.183803] pci 0000:00:1d.7: reg 10 32bit mmio: [0xf9fff800-0xf9fffbff] [ 0.183906] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 0.183956] pci 0000:00:1d.7: PME# disabled [ 0.184220] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO [ 0.184277] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO [ 0.184325] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0294 (mask 0003) [ 0.184505] pci 0000:00:1f.2: reg 10 io port: [0x9c00-0x9c07] [ 0.184515] pci 0000:00:1f.2: reg 14 io port: [0x9880-0x9883] [ 0.184526] pci 0000:00:1f.2: reg 18 io port: [0x9800-0x9807] [ 0.184536] pci 0000:00:1f.2: reg 1c io port: [0x9480-0x9483] [ 0.184547] pci 0000:00:1f.2: reg 20 io port: [0x9400-0x941f] [ 0.184557] pci 0000:00:1f.2: reg 24 32bit mmio: [0xf9ffe800-0xf9ffefff] [ 0.184623] pci 0000:00:1f.2: PME# supported from D3hot [ 0.184671] pci 0000:00:1f.2: PME# disabled [ 0.184769] pci 0000:00:1f.3: reg 10 64bit mmio: [0xf9fff400-0xf9fff4ff] [ 0.184795] pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f] [ 0.184890] pci 0000:01:00.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff] [ 0.184908] pci 0000:01:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff] [ 0.184927] pci 0000:01:00.0: reg 1c 64bit mmio: [0xfa000000-0xfbffffff] [ 0.184937] pci 0000:01:00.0: reg 24 io port: [0xbc00-0xbc7f] [ 0.184947] pci 0000:01:00.0: reg 30 32bit mmio: [0xfe8e0000-0xfe8fffff] [ 0.185073] pci 0000:00:01.0: bridge io port: [0xb000-0xbfff] [ 0.185079] pci 0000:00:01.0: bridge 32bit mmio: [0xfa000000-0xfe8fffff] [ 0.185088] pci 0000:00:01.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff] [ 0.185179] pci 0000:00:1c.0: bridge 64bit mmio pref: [0xf8f00000-0xf8ffffff] [ 0.185324] pci 0000:03:00.0: reg 24 32bit mmio: [0xfeafe000-0xfeafffff] [ 0.185338] pci 0000:03:00.0: reg 30 32bit mmio: [0xfeae0000-0xfeaeffff] [ 0.185389] pci 0000:03:00.0: PME# supported from D3hot [ 0.185438] pci 0000:03:00.0: PME# disabled [ 0.185560] pci 0000:03:00.1: reg 10 io port: [0xdc00-0xdc07] [ 0.185574] pci 0000:03:00.1: reg 14 io port: [0xd880-0xd883] [ 0.185588] pci 0000:03:00.1: reg 18 io port: [0xd800-0xd807] [ 0.185601] pci 0000:03:00.1: reg 1c io port: [0xd480-0xd483] [ 0.185615] pci 0000:03:00.1: reg 20 io port: [0xd400-0xd40f] [ 0.185775] pci 0000:00:1c.4: bridge io port: [0xd000-0xdfff] [ 0.185782] pci 0000:00:1c.4: bridge 32bit mmio: [0xfea00000-0xfeafffff] [ 0.185889] pci 0000:02:00.0: reg 10 64bit mmio: [0xfe9fc000-0xfe9fffff] [ 0.185902] pci 0000:02:00.0: reg 18 io port: [0xc800-0xc8ff] [ 0.185945] pci 0000:02:00.0: reg 30 32bit mmio: [0xfe9c0000-0xfe9dffff] [ 0.186013] pci 0000:02:00.0: supports D1 D2 [ 0.186015] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.186066] pci 0000:02:00.0: PME# disabled [ 0.186188] pci 0000:00:1c.5: bridge io port: [0xc000-0xcfff] [ 0.186195] pci 0000:00:1c.5: bridge 32bit mmio: [0xfe900000-0xfe9fffff] [ 0.186272] pci 0000:05:03.0: reg 10 32bit mmio: [0xfebff000-0xfebfffff] [ 0.186359] pci 0000:05:03.0: supports D1 D2 [ 0.186362] pci 0000:05:03.0: PME# supported from D0 D1 D2 D3hot [ 0.186411] pci 0000:05:03.0: PME# disabled [ 0.186512] pci 0000:05:04.0: reg 10 io port: [0xe800-0xe8ff] [ 0.186524] pci 0000:05:04.0: reg 14 32bit mmio: [0xfebfec00-0xfebfecff] [ 0.186571] pci 0000:05:04.0: reg 30 32bit mmio: [0xfebc0000-0xfebdffff] [ 0.186605] pci 0000:05:04.0: supports D1 D2 [ 0.186608] pci 0000:05:04.0: PME# supported from D1 D2 D3hot D3cold [ 0.186657] pci 0000:05:04.0: PME# disabled [ 0.186771] pci 0000:00:1e.0: transparent bridge [ 0.186818] pci 0000:00:1e.0: bridge io port: [0xe000-0xefff] [ 0.186825] pci 0000:00:1e.0: bridge 32bit mmio: [0xfeb00000-0xfebfffff] [ 0.186877] pci_bus 0000:00: on NUMA node 0 [ 0.186884] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.187092] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT] [ 0.187165] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 0.187324] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] [ 0.187404] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT] [ 0.187486] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT] [ 0.210324] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 0.210855] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15) [ 0.211383] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 0.211911] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 *14 15) [ 0.212439] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.213035] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 10 11 12 14 15) [ 0.213562] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 *15) [ 0.214090] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15) [ 0.214709] ACPI Warning (tbutils-0242): Incorrect checksum in table [OEMB] - 67, should be 5E [20081204] [ 0.214909] xen_balloon: Initialising balloon driver. [ 0.215415] SCSI subsystem initialized [ 0.215558] libata version 3.00 loaded. [ 0.215989] PCI: Using ACPI for IRQ routing [ 0.240025] NET: Registered protocol family 8 [ 0.240077] NET: Registered protocol family 20 [ 0.240186] NetLabel: Initializing [ 0.240228] NetLabel: domain hash size = 128 [ 0.240271] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.240327] NetLabel: unlabeled traffic allowed by default [ 0.241162] Xen: Initializing Xen DMA ops [ 0.241205] Xen: Enabling DMA fallback to swiotlb [ 0.280025] pnp: PnP ACPI init [ 0.280088] ACPI: bus type pnp registered [ 0.280634] xen: registering gsi 8 triggering 1 polarity 0 [ 0.280638] xen_allocate_pirq: returning irq 8 for gsi 8 [ 0.280682] xen: --> irq=8 [ 0.280686] xen_set_ioapic_routing: irq 8 gsi 8 vector 80 ioapic 0 pin 8 triggering 1 polarity 0 [ 0.280913] xen: registering gsi 13 triggering 1 polarity 0 [ 0.280916] xen_allocate_pirq: returning irq 13 for gsi 13 [ 0.280960] xen: --> irq=13 [ 0.280963] xen_set_ioapic_routing: irq 13 gsi 13 vector 120 ioapic 0 pin 13 triggering 1 polarity 0 [ 0.281781] xen: registering gsi 6 triggering 1 polarity 0 [ 0.281784] xen_allocate_pirq: returning irq 6 for gsi 6 [ 0.281829] xen: --> irq=6 [ 0.281832] xen_set_ioapic_routing: irq 6 gsi 6 vector 64 ioapic 0 pin 6 triggering 1 polarity 0 [ 0.283363] xen: registering gsi 4 triggering 1 polarity 0 [ 0.283366] xen_allocate_pirq: returning irq 4 for gsi 4 [ 0.283410] xen: --> irq=4 [ 0.283413] xen_set_ioapic_routing: irq 4 gsi 4 vector 48 ioapic 0 pin 4 triggering 1 polarity 0 [ 0.284436] xen: registering gsi 1 triggering 1 polarity 0 [ 0.284439] xen_allocate_pirq: returning irq 1 for gsi 1 [ 0.284484] xen: --> irq=1 [ 0.284486] xen_set_ioapic_routing: irq 1 gsi 1 vector 32 ioapic 0 pin 1 triggering 1 polarity 0 [ 0.286099] pnp: PnP ACPI: found 15 devices [ 0.286144] ACPI: ACPI bus type pnp unregistered [ 0.286197] system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved [ 0.286251] system 00:07: ioport range 0x290-0x297 has been reserved [ 0.286302] system 00:08: ioport range 0x4d0-0x4d1 has been reserved [ 0.286347] system 00:08: ioport range 0x800-0x87f has been reserved [ 0.286393] system 00:08: ioport range 0x480-0x4bf has been reserved [ 0.286438] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved [ 0.286485] system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved [ 0.286531] system 00:08: iomem range 0xfed50000-0xfed8ffff has been reserved [ 0.286577] system 00:08: iomem range 0xffa00000-0xffafffff has been reserved [ 0.286623] system 00:08: iomem range 0xffb00000-0xffbfffff has been reserved [ 0.286669] system 00:08: iomem range 0xffe00000-0xffefffff has been reserved [ 0.286716] system 00:08: iomem range 0xfff00000-0xfffffffe has been reserved [ 0.286767] system 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved [ 0.286814] system 00:0b: iomem range 0xfee00000-0xfee00fff has been reserved [ 0.286865] system 00:0d: iomem range 0xe0000000-0xefffffff has been reserved [ 0.286916] system 00:0e: iomem range 0x0-0x9ffff could not be reserved [ 0.286962] system 00:0e: iomem range 0xc0000-0xcffff could not be reserved [ 0.287008] system 00:0e: iomem range 0xe0000-0xfffff could not be reserved [ 0.287054] system 00:0e: iomem range 0x100000-0xcfffffff could not be reserved [ 0.292348] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 [ 0.292395] pci 0000:00:01.0: IO window: 0xb000-0xbfff [ 0.292445] pci 0000:00:01.0: MEM window: 0xfa000000-0xfe8fffff [ 0.292493] pci 0000:00:01.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff [ 0.292555] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:04 [ 0.292599] pci 0000:00:1c.0: IO window: disabled [ 0.292648] pci 0000:00:1c.0: MEM window: disabled [ 0.292696] pci 0000:00:1c.0: PREFETCH window: 0x000000f8f00000-0x000000f8ffffff [ 0.292759] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:03 [ 0.292806] pci 0000:00:1c.4: IO window: 0xd000-0xdfff [ 0.292856] pci 0000:00:1c.4: MEM window: 0xfea00000-0xfeafffff [ 0.292904] pci 0000:00:1c.4: PREFETCH window: disabled [ 0.292956] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:02 [ 0.293003] pci 0000:00:1c.5: IO window: 0xc000-0xcfff [ 0.293053] pci 0000:00:1c.5: MEM window: 0xfe900000-0xfe9fffff [ 0.293101] pci 0000:00:1c.5: PREFETCH window: disabled [ 0.293154] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05 [ 0.293201] pci 0000:00:1e.0: IO window: 0xe000-0xefff [ 0.293251] pci 0000:00:1e.0: MEM window: 0xfeb00000-0xfebfffff [ 0.293299] pci 0000:00:1e.0: PREFETCH window: 0x00000050000000-0x000000500fffff [ 0.293370] xen: registering gsi 16 triggering 0 polarity 1 [ 0.293380] xen: --> irq=16 [ 0.293382] xen_set_ioapic_routing: irq 16 gsi 16 vector 160 ioapic 0 pin 16 triggering 0 polarity 1 [ 0.293443] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.293492] pci 0000:00:01.0: setting latency timer to 64 [ 0.293504] xen: registering gsi 17 triggering 0 polarity 1 [ 0.293510] xen: --> irq=17 [ 0.293513] xen_set_ioapic_routing: irq 17 gsi 17 vector 168 ioapic 0 pin 17 triggering 0 polarity 1 [ 0.293573] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 0.293622] pci 0000:00:1c.0: setting latency timer to 64 [ 0.293634] xen: registering gsi 17 triggering 0 polarity 1 [ 0.293637] xen_allocate_pirq: returning irq 17 for gsi 17 [ 0.293681] xen: --> irq=17 [ 0.293684] xen_set_ioapic_routing: irq 17 gsi 17 vector 168 ioapic 0 pin 17 triggering 0 polarity 1 [ 0.293742] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 0.293791] pci 0000:00:1c.4: setting latency timer to 64 [ 0.293803] xen: registering gsi 16 triggering 0 polarity 1 [ 0.293806] xen_allocate_pirq: returning irq 16 for gsi 16 [ 0.293850] xen: --> irq=16 [ 0.293852] xen_set_ioapic_routing: irq 16 gsi 16 vector 160 ioapic 0 pin 16 triggering 0 polarity 1 [ 0.293911] pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16 [ 0.293960] pci 0000:00:1c.5: setting latency timer to 64 [ 0.293972] pci 0000:00:1e.0: setting latency timer to 64 [ 0.293977] pci_bus 0000:00: resource 0 io: [0x00-0xffff] [ 0.293980] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff] [ 0.293983] pci_bus 0000:01: resource 0 io: [0xb000-0xbfff] [ 0.293985] pci_bus 0000:01: resource 1 mem: [0xfa000000-0xfe8fffff] [ 0.293988] pci_bus 0000:01: resource 2 mem: [0xd0000000-0xdfffffff] [ 0.293991] pci_bus 0000:01: resource 3 mem: [0x0-0x0] [ 0.293993] pci_bus 0000:04: resource 0 mem: [0x0-0x0] [ 0.293996] pci_bus 0000:04: resource 1 mem: [0x0-0x0] [ 0.293998] pci_bus 0000:04: resource 2 mem: [0xf8f00000-0xf8ffffff] [ 0.294001] pci_bus 0000:04: resource 3 mem: [0x0-0x0] [ 0.294004] pci_bus 0000:03: resource 0 io: [0xd000-0xdfff] [ 0.294006] pci_bus 0000:03: resource 1 mem: [0xfea00000-0xfeafffff] [ 0.294009] pci_bus 0000:03: resource 2 mem: [0x0-0x0] [ 0.294011] pci_bus 0000:03: resource 3 mem: [0x0-0x0] [ 0.294014] pci_bus 0000:02: resource 0 io: [0xc000-0xcfff] [ 0.294017] pci_bus 0000:02: resource 1 mem: [0xfe900000-0xfe9fffff] [ 0.294019] pci_bus 0000:02: resource 2 mem: [0x0-0x0] [ 0.294022] pci_bus 0000:02: resource 3 mem: [0x0-0x0] [ 0.294025] pci_bus 0000:05: resource 0 io: [0xe000-0xefff] [ 0.294027] pci_bus 0000:05: resource 1 mem: [0xfeb00000-0xfebfffff] [ 0.294030] pci_bus 0000:05: resource 2 mem: [0x50000000-0x500fffff] [ 0.294033] pci_bus 0000:05: resource 3 io: [0x00-0xffff] [ 0.294035] pci_bus 0000:05: resource 4 mem: [0x000000-0xffffffffffffffff] [ 0.294096] NET: Registered protocol family 2 [ 0.420127] IP route cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.420568] TCP established hash table entries: 131072 (order: 9, 2097152 bytes) [ 0.421132] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.421440] TCP: Hash tables configured (established 131072 bind 65536) [ 0.421485] TCP reno registered [ 0.460139] NET: Registered protocol family 1 [ 0.460302] checking if image is initramfs... it is [ 0.583284] Freeing initrd memory: 183563k freed [ 0.644751] audit: initializing netlink socket (disabled) [ 0.644820] type=2000 audit(1234977952.276:1): initialized [ 0.649413] VFS: Disk quotas dquot_6.5.2 [ 0.649509] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.649616] msgmni has been set to 2406 [ 0.649860] alg: No test for stdrng (krng) [ 0.649923] io scheduler noop registered [ 0.649967] io scheduler anticipatory registered [ 0.650013] io scheduler deadline registered (default) [ 0.650104] io scheduler cfq registered [ 0.650365] pci 0000:01:00.0: Boot video device [ 0.650563] pcieport-driver 0000:00:01.0: setting latency timer to 64 [ 0.650849] pcieport-driver 0000:00:1c.0: setting latency timer to 64 [ 0.651168] pcieport-driver 0000:00:1c.4: setting latency timer to 64 [ 0.651488] pcieport-driver 0000:00:1c.5: setting latency timer to 64 [ 0.652221] xenbus_probe_backend_init bus registered ok [ 0.652319] xenbus_probe_frontend_init bus registered ok [ 0.652434] Event-channel device installed. [ 0.652477] ***blkif_init [ 0.654589] *** netif_init [ 0.655343] registering netback [ 0.696151] Linux agpgart interface v0.103 [ 0.698363] brd: module loaded [ 0.698551] input: Macintosh mouse button emulation as /devices/virtual/input/input0 [ 0.698643] ahci 0000:00:1f.2: version 3.0 [ 0.698662] xen: registering gsi 22 triggering 0 polarity 1 [ 0.698673] xen: --> irq=22 [ 0.698677] xen_set_ioapic_routing: irq 22 gsi 22 vector 176 ioapic 0 pin 22 triggering 0 polarity 1 [ 0.698738] ahci 0000:00:1f.2: PCI INT B -> GSI 22 (level, low) -> IRQ 22 [ 0.698867] ahci: SSS flag set, parallel bus scan disabled [ 0.698939] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode [ 0.698996] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pmp pio slum part ems [ 0.699056] ahci 0000:00:1f.2: setting latency timer to 64 [ 0.699667] scsi0 : ahci [ 0.699907] scsi1 : ahci [ 0.700201] scsi2 : ahci [ 0.700402] scsi3 : ahci [ 0.700597] scsi4 : ahci [ 0.700799] scsi5 : ahci [ 0.701165] ata1: SATA max UDMA/133 abar m2048@0xf9ffe800 port 0xf9ffe900 irq 22 [ 0.701222] ata2: SATA max UDMA/133 abar m2048@0xf9ffe800 port 0xf9ffe980 irq 22 [ 0.701277] ata3: SATA max UDMA/133 abar m2048@0xf9ffe800 port 0xf9ffea00 irq 22 [ 0.701332] ata4: SATA max UDMA/133 abar m2048@0xf9ffe800 port 0xf9ffea80 irq 22 [ 0.701387] ata5: SATA max UDMA/133 abar m2048@0xf9ffe800 port 0xf9ffeb00 irq 22 [ 0.701442] ata6: SATA max UDMA/133 abar m2048@0xf9ffe800 port 0xf9ffeb80 irq 22 [ 1.230022] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.230656] ata1.00: ATA-7: ST3250410AS, 3.AAC, max UDMA/133 [ 1.230708] ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 1.231428] ata1.00: configured for UDMA/133 [ 1.250139] scsi 0:0:0:0: Direct-Access ATA ST3250410AS 3.AA PQ: 0 ANSI: 5 [ 1.780022] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.780611] ata2.00: ATA-7: ST3250410AS, 3.AAC, max UDMA/133 [ 1.780662] ata2.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 1.781409] ata2.00: configured for UDMA/133 [ 1.800123] scsi 1:0:0:0: Direct-Access ATA ST3250410AS 3.AA PQ: 0 ANSI: 5 [ 2.150025] ata3: SATA link down (SStatus 0 SControl 300) [ 2.520024] ata4: SATA link down (SStatus 0 SControl 300) [ 2.890024] ata5: SATA link down (SStatus 0 SControl 300) [ 3.260023] ata6: SATA link down (SStatus 0 SControl 300) [ 3.280062] xen: registering gsi 16 triggering 0 polarity 1 [ 3.280067] xen_allocate_pirq: returning irq 16 for gsi 16 [ 3.280122] xen: --> irq=16 [ 3.280125] xen_set_ioapic_routing: irq 16 gsi 16 vector 160 ioapic 0 pin 16 triggering 0 polarity 1 [ 3.280184] ahci 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.300046] ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode [ 3.300116] ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part [ 3.300168] ahci 0000:03:00.0: setting latency timer to 64 [ 3.300380] scsi6 : ahci [ 3.300580] scsi7 : ahci [ 3.300807] ata7: SATA max UDMA/133 abar m8192@0xfeafe000 port 0xfeafe100 irq 16 [ 3.300864] ata8: SATA max UDMA/133 abar m8192@0xfeafe000 port 0xfeafe180 irq 16 [ 3.650044] ata7: SATA link down (SStatus 0 SControl 300) [ 4.020035] ata8: SATA link down (SStatus 0 SControl 300) [ 4.040225] pata_jmicron 0000:03:00.1: enabling device (0000 -> 0001) [ 4.040274] xen: registering gsi 17 triggering 0 polarity 1 [ 4.040277] xen_allocate_pirq: returning irq 17 for gsi 17 [ 4.040321] xen: --> irq=17 [ 4.040323] xen_set_ioapic_routing: irq 17 gsi 17 vector 168 ioapic 0 pin 17 triggering 0 polarity 1 [ 4.040382] pata_jmicron 0000:03:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 4.040472] pata_jmicron 0000:03:00.1: setting latency timer to 64 [ 4.040563] scsi8 : pata_jmicron [ 4.040757] scsi9 : pata_jmicron [ 4.041922] ata9: PATA max UDMA/100 cmd 0xdc00 ctl 0xd880 bmdma 0xd400 irq 17 [ 4.041969] ata10: PATA max UDMA/100 cmd 0xd800 ctl 0xd480 bmdma 0xd408 irq 17 [ 4.220580] ata9.00: ATAPI: Optiarc DVD RW AD-5200A, 1.03, max UDMA/66 [ 4.260586] ata9.00: configured for UDMA/66 [ 4.264257] scsi 8:0:0:0: CD-ROM Optiarc DVD RW AD-5200A 1.03 PQ: 0 ANSI: 5 [ 4.432024] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 [ 4.432070] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp [ 4.432692] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 4.460188] mice: PS/2 mouse device common for all mice [ 4.460320] rtc_cmos 00:03: RTC can wake from S4 [ 4.460452] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 4.460520] rtc0: alarms up to one month, y3k, 114 bytes nvram [ 4.460618] cpuidle: using governor ladder [ 4.461165] TCP cubic registered [ 4.461258] Bridge firewalling registered [ 4.461330] IO APIC resources could be not be allocated. [ 4.461585] registered taskstats version 1 [ 4.461765] Magic number: 13:504:441 [ 4.461913] rtc_cmos 00:03: setting system clock to 2009-02-18 17:25:55 UTC (1234977955) [ 4.461970] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 4.462014] EDD information not available. [ 4.462101] Freeing unused kernel memory: 456k freed [ 4.462291] Write protecting the kernel read-only data: 4652k [ 4.479099] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 [ 4.567451] fuse init (API version 7.11) [ 4.595928] device-mapper: uevent: version 1.0.3 [ 4.596145] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com [ 4.849829] usbcore: registered new interface driver usbfs [ 4.849901] usbcore: registered new interface driver hub [ 4.860789] usbcore: registered new device driver usb [ 4.863262] uhci_hcd: USB Universal Host Controller Interface driver [ 4.863349] xen: registering gsi 16 triggering 0 polarity 1 [ 4.863353] xen_allocate_pirq: returning irq 16 for gsi 16 [ 4.863397] xen: --> irq=16 [ 4.863400] xen_set_ioapic_routing: irq 16 gsi 16 vector 160 ioapic 0 pin 16 triggering 0 polarity 1 [ 4.863461] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4.863516] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 4.863522] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 4.863608] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 [ 4.863691] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000a800 [ 4.863991] usb usb1: configuration #1 chosen from 1 choice [ 4.864063] hub 1-0:1.0: USB hub found [ 4.864118] hub 1-0:1.0: 2 ports detected [ 4.864298] xen: registering gsi 21 triggering 0 polarity 1 [ 4.864308] xen: --> irq=21 [ 4.864311] xen_set_ioapic_routing: irq 21 gsi 21 vector 184 ioapic 0 pin 21 triggering 0 polarity 1 [ 4.864371] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 4.864423] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 4.864428] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 4.864495] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2 [ 4.864593] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000a880 [ 4.864748] usb usb2: configuration #1 chosen from 1 choice [ 4.864821] hub 2-0:1.0: USB hub found [ 4.864875] hub 2-0:1.0: 2 ports detected [ 4.865033] xen: registering gsi 18 triggering 0 polarity 1 [ 4.865039] xen: --> irq=18 [ 4.865042] xen_set_ioapic_routing: irq 18 gsi 18 vector 192 ioapic 0 pin 18 triggering 0 polarity 1 [ 4.865101] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 4.865153] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 4.865158] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 4.865224] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3 [ 4.865314] uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000ac00 [ 4.865485] usb usb3: configuration #1 chosen from 1 choice [ 4.865576] hub 3-0:1.0: USB hub found [ 4.865633] hub 3-0:1.0: 2 ports detected [ 4.865803] xen: registering gsi 23 triggering 0 polarity 1 [ 4.865811] xen: --> irq=23 [ 4.865814] xen_set_ioapic_routing: irq 23 gsi 23 vector 200 ioapic 0 pin 23 triggering 0 polarity 1 [ 4.865874] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 4.865927] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 4.865932] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 4.866005] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4 [ 4.866101] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000a080 [ 4.866259] usb usb4: configuration #1 chosen from 1 choice [ 4.866336] hub 4-0:1.0: USB hub found [ 4.866396] hub 4-0:1.0: 2 ports detected [ 4.866558] xen: registering gsi 19 triggering 0 polarity 1 [ 4.866565] xen: --> irq=19 [ 4.866568] xen_set_ioapic_routing: irq 19 gsi 19 vector 208 ioapic 0 pin 19 triggering 0 polarity 1 [ 4.866628] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 4.866680] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 4.866685] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 4.866753] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5 [ 4.866846] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000a400 [ 4.867019] usb usb5: configuration #1 chosen from 1 choice [ 4.867095] hub 5-0:1.0: USB hub found [ 4.867152] hub 5-0:1.0: 2 ports detected [ 4.867308] xen: registering gsi 18 triggering 0 polarity 1 [ 4.867311] xen_allocate_pirq: returning irq 18 for gsi 18 [ 4.867356] xen: --> irq=18 [ 4.867359] xen_set_ioapic_routing: irq 18 gsi 18 vector 192 ioapic 0 pin 18 triggering 0 polarity 1 [ 4.867421] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 4.867477] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 4.867482] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 4.867552] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6 [ 4.867638] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000a480 [ 4.867800] usb usb6: configuration #1 chosen from 1 choice [ 4.867873] hub 6-0:1.0: USB hub found [ 4.867929] hub 6-0:1.0: 2 ports detected [ 4.870567] ehci_hcd: USB 2.0 ''Enhanced'' Host Controller (EHCI) Driver [ 4.870615] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after [ 4.870694] xen: registering gsi 18 triggering 0 polarity 1 [ 4.870697] xen_allocate_pirq: returning irq 18 for gsi 18 [ 4.870745] xen: --> irq=18 [ 4.870748] xen_set_ioapic_routing: irq 18 gsi 18 vector 192 ioapic 0 pin 18 triggering 0 polarity 1 [ 4.870812] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 4.870878] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 4.870884] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 4.870956] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 7 [ 4.874937] ehci_hcd 0000:00:1a.7: debug port 1 [ 4.874989] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported [ 4.874997] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf9fffc00 [ 4.890098] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 4.890292] usb usb7: configuration #1 chosen from 1 choice [ 4.890370] hub 7-0:1.0: USB hub found [ 4.890431] hub 7-0:1.0: 6 ports detected [ 4.890628] xen: registering gsi 23 triggering 0 polarity 1 [ 4.890631] xen_allocate_pirq: returning irq 23 for gsi 23 [ 4.890678] xen: --> irq=23 [ 4.890681] xen_set_ioapic_routing: irq 23 gsi 23 vector 200 ioapic 0 pin 23 triggering 0 polarity 1 [ 4.890743] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 4.890806] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 4.890813] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 4.890887] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8 [ 4.894865] ehci_hcd 0000:00:1d.7: debug port 1 [ 4.894916] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported [ 4.894924] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf9fff800 [ 4.900994] scsi 0:0:0:0: Attached scsi generic sg0 type 0 [ 4.901079] scsi 1:0:0:0: Attached scsi generic sg1 type 0 [ 4.901170] scsi 8:0:0:0: Attached scsi generic sg2 type 5 [ 4.910925] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 4.911109] usb usb8: configuration #1 chosen from 1 choice [ 4.911185] hub 8-0:1.0: USB hub found [ 4.911398] hub 8-0:1.0: 6 ports detected [ 4.929585] sky2 driver version 1.22 [ 4.929673] xen: registering gsi 17 triggering 0 polarity 1 [ 4.929676] xen_allocate_pirq: returning irq 17 for gsi 17 [ 4.929721] xen: --> irq=17 [ 4.929725] xen_set_ioapic_routing: irq 17 gsi 17 vector 168 ioapic 0 pin 17 triggering 0 polarity 1 [ 4.929787] sky2 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 4.929845] sky2 0000:02:00.0: setting latency timer to 64 [ 4.929889] sky2 0000:02:00.0: Yukon-2 EC Ultra chip revision 3 [ 4.962126] sky2 0000:02:00.0: Marvell Yukon 88E8056 Gigabit Ethernet Controller [ 4.962186] Part Number: Yukon 88E8056 [ 4.962188] Engineering Level: Rev. 1.2 [ 4.962191] Manufacturer: Marvell [ 4.962572] sky2 eth0: addr 00:1e:8c:25:d9:23 [ 5.015015] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 5.015082] xen: registering gsi 16 triggering 0 polarity 1 [ 5.015085] xen_allocate_pirq: returning irq 16 for gsi 16 [ 5.015130] xen: --> irq=16 [ 5.015133] xen_set_ioapic_routing: irq 16 gsi 16 vector 160 ioapic 0 pin 16 triggering 0 polarity 1 [ 5.015197] r8169 0000:05:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 5.015283] r8169 0000:05:04.0: no PCI Express capability [ 5.015750] eth1: RTL8169sc/8110sc at 0xffffc20000056c00, 00:1e:8c:25:cc:a5, XID 18000000 IRQ 16 [ 5.020915] xen: registering gsi 19 triggering 0 polarity 1 [ 5.020920] xen_allocate_pirq: returning irq 19 for gsi 19 [ 5.020967] xen: --> irq=19 [ 5.020971] xen_set_ioapic_routing: irq 19 gsi 19 vector 208 ioapic 0 pin 19 triggering 0 polarity 1 [ 5.021032] ohci1394 0000:05:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 5.025107] Driver ''sr'' needs updating - please use bus_type methods [ 5.030286] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray [ 5.030334] Uniform CD-ROM driver Revision: 3.20 [ 5.030473] sr 8:0:0:0: Attached scsi CD-ROM sr0 [ 5.036150] Driver ''sd'' needs updating - please use bus_type methods [ 5.036299] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB) [ 5.036377] sd 0:0:0:0: [sda] Write Protect is off [ 5.036422] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 5.036464] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn''t support DPO or FUA [ 5.036597] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB) [ 5.036674] sd 0:0:0:0: [sda] Write Protect is off [ 5.036718] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 5.036761] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn''t support DPO or FUA [ 5.036821] sda: sda1 sda2 sda3 sda4 < > [ 5.054561] sd 0:0:0:0: [sda] Attached SCSI disk [ 5.054684] sd 1:0:0:0: [sdb] 488397168 512-byte hardware sectors: (250 GB/232 GiB) [ 5.054761] sd 1:0:0:0: [sdb] Write Protect is off [ 5.054806] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 5.054848] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn''t support DPO or FUA [ 5.054972] sd 1:0:0:0: [sdb] 488397168 512-byte hardware sectors: (250 GB/232 GiB) [ 5.055049] sd 1:0:0:0: [sdb] Write Protect is off [ 5.055093] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 5.055135] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn''t support DPO or FUA [ 5.055870] sdb: sdb1 sdb2 sdb3 sdb4 <<6>ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[19] MMIO=[febff000-febff7ff] Max Packet=[2048] IR/IT contexts=[8/8] [ 5.089238] sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 sdb11 sdb12 sdb13 sdb14 sdb15 > [ 5.210775] usb 7-3: new high speed USB device using ehci_hcd and address 2 [ 5.225446] sd 1:0:0:0: [sdb] Attached SCSI disk [ 5.366717] usb 7-3: configuration #1 chosen from 1 choice [ 5.820052] usb 6-2: new low speed USB device using uhci_hcd and address 2 [ 5.978885] usb 6-2: configuration #1 chosen from 1 choice [ 5.997653] usbcore: registered new interface driver hiddev [ 6.011010] input: HID 062a:0001 as /devices/pci0000:00/0000:00:1d.2/usb6/6-2/6-2:1.0/input/input2 [ 6.060151] generic-usb 0003:062A:0001.0001: input,hidraw0: USB HID v1.10 Mouse [HID 062a:0001] on usb-0000:00:1d.2-2/input0 [ 6.060227] usbcore: registered new interface driver usbhid [ 6.060273] usbhid: v2.6:USB HID core driver [ 6.400260] ieee1394: Host added: ID:BUS[0-00:1023] GUID[001e8c00000473b7] [ 6.851294] kjournald starting. Commit interval 5 seconds [ 6.851362] EXT3-fs: mounted filesystem with ordered data mode. [ 10.765443] udevd version 124 started [ 11.208483] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 11.275883] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 11.381050] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 11.420109] ACPI: Power Button (FF) [PWRF] [ 11.420268] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4 [ 11.470057] ACPI: Power Button (CM) [PWRB] [ 11.620858] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 11.621039] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 11.775043] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 11.995737] iTCO_vendor_support: vendor-support=0 [ 12.060129] cfg80211: Using static regulatory domain info [ 12.060178] cfg80211: Regulatory domain: US [ 12.060221] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 12.060278] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) [ 12.060330] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 12.060379] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 12.060426] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 12.060472] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 12.060519] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) [ 12.060566] cfg80211: Calling CRDA for country: US [ 12.093247] input: PC Speaker as /devices/platform/pcspkr/input/input5 [ 12.245134] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.04 [ 12.245331] iTCO_wdt: Found a ICH9R TCO device (Version=2, TCOBASE=0x0860) [ 12.245470] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 15.046681] wmaster0 (rtl8187): not using net_device_ops yet [ 15.047140] phy0: Selected rate control algorithm ''minstrel'' [ 15.706225] xen: registering gsi 22 triggering 0 polarity 1 [ 15.706229] xen_allocate_pirq: returning irq 22 for gsi 22 [ 15.706277] xen: --> irq=22 [ 15.706280] xen_set_ioapic_routing: irq 22 gsi 22 vector 176 ioapic 0 pin 22 triggering 0 polarity 1 [ 15.706341] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 15.706504] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 15.774706] wlan0 (rtl8187): not using net_device_ops yet [ 15.775204] phy0: hwaddr 00:15:af:51:c2:c0, RTL8187vB (default) V1 + rtl8225z2 [ 15.775285] usbcore: registered new interface driver rtl8187 [ 18.674020] loop: module loaded [ 18.865229] lp: driver loaded but no devices found [ 19.908034] EXT3 FS on sdb1, internal journal [ 21.061847] ip_tables: (C) 2000-2006 Netfilter Core Team [ 21.145990] sky2 eth0: enabling interface [ 22.371371] NET: Registered protocol family 17 [ 24.535749] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both [ 35.238274] NET: Registered protocol family 10 [ 35.239078] lo: Disabled Privacy Extensions [ 36.926689] warning: `avahi-daemon'' uses 32-bit capabilities (legacy support in use) [ 37.161134] ppdev: user-space parallel port driver [ 38.922842] Bluetooth: Core ver 2.14 [ 38.923043] NET: Registered protocol family 31 [ 38.923046] Bluetooth: HCI device and connection manager initialized [ 38.923050] Bluetooth: HCI socket layer initialized [ 38.959459] Bluetooth: L2CAP ver 2.11 [ 38.959462] Bluetooth: L2CAP socket layer initialized [ 38.972740] Bluetooth: SCO (Voice Link) ver 0.6 [ 38.972743] Bluetooth: SCO socket layer initialized [ 39.009988] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 39.009991] Bluetooth: BNEP filters: protocol multicast [ 39.230075] Bluetooth: RFCOMM socket layer initialized [ 39.230085] Bluetooth: RFCOMM TTY layer initialized [ 39.230088] Bluetooth: RFCOMM ver 1.10 [ 43.340771] r8169: eth1: link down [ 43.340887] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 45.520018] eth0: no IPv6 routers present [ 45.601547] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 45.920049] sky2 eth0: disabling interface [ 45.967352] sky2 peth0: enabling interface [ 45.967502] ADDRCONF(NETDEV_UP): peth0: link is not ready [ 45.984635] device peth0 entered promiscuous mode [ 47.890223] sky2 peth0: Link is up at 100 Mbps, full duplex, flow control both [ 47.890313] eth0: topology change detected, propagating [ 47.890317] eth0: port 1(peth0) entering forwarding state [ 47.890329] ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready [ 56.130017] eth0: no IPv6 routers present [ 58.560017] peth0: no IPv6 routers present [ 61.007528] xenbus_probe wake_waiting [ 61.007589] xenbus_probe wake_waiting [ 61.017906] xenbus_probe_devices backend [ 61.018050] xenbus_probe_devices failed xenbus_directory [ 61.018095] backend_probe_and_watch devices probed ok [ 61.018238] backend_probe_and_watch watch add ok ok [ 61.018283] backend_probe_and_watch all done [ 61.018327] xenbus_probe_devices device [ 61.018463] xenbus_probe_devices failed xenbus_directory [ 61.018509] frontend_probe_and_watch devices probed ok [ 61.018654] frontend_probe_and_watch watch add ok ok [ 61.018699] frontend_probe_and_watch all done --- On Wed, 2/18/09, Boris Derzhavets <bderzhavets@yahoo.com> wrote: From: Boris Derzhavets <bderzhavets@yahoo.com> Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip To: "Marc - A. Dahlhaus [ Administration | Westermann GmbH ]" <mad@wol.de> Cc: "xen-devel@lists.xensource.com" <xen-devel@lists.xensource.com> Date: Wednesday, February 18, 2009, 10:49 AM Mark, I''ve just tried. Your procedure works grate. I will try to load kernel (under Xen Unstable) after patching per Jeremy. Thank you. Boris. P.S. root@ServerXen331:~# git --version git version 1.5.6.3 --- On Tue, 2/17/09, Marc - A. Dahlhaus [ Administration | Westermann GmbH ] <mad@wol.de> wrote: From: Marc - A. Dahlhaus [ Administration | Westermann GmbH ] <mad@wol.de> Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip To: bderzhavets@yahoo.com Cc: "xen-devel@lists.xensource.com" <xen-devel@lists.xensource.com> Date: Tuesday, February 17, 2009, 9:09 AM Hello Boris, with git >= v1.5 you can get to the right branch even simpler with: git clone git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git linux-2.6-xen cd linux-2.6-xen git checkout origin/xen/dom0/hackery -b xen/dom0/hackery To update: git pull Works like a charm here but i didn''t had the time to boottest it... Am Dienstag, den 17.02.2009, 05:31 -0800 schrieb Boris Derzhavets:> Hardware config:- > C2D E8400, 8 GB RAM, ASUS P5K Premium/WIFI (Intel P35+Intel ICH9R), > 2x250 SATA Seagate Barracuda (no RAID). Bios settings for ICH9R - > AHCI. > Details here:- >http://bderzhavets.wordpress.com/2009/02/17/setup-xen-unstable-dom0-via-2629-rc5-pv_ops-enabled-kernel-on-intel-sataahci/> > > --- On Tue, 2/17/09, Pasi Kärkkäinen <pasik@iki.fi> wrote: > From: Pasi Kärkkäinen <pasik@iki.fi> > Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip > To: "Boris Derzhavets"<bderzhavets@yahoo.com>> Cc: "Ian Campbell" <Ian.Campbell@eu.citrix.com>,"Jeremy> Fitzhardinge" <jeremy@goop.org>, > "xen-devel@lists.xensource.com" > <xen-devel@lists.xensource.com> > Date: Tuesday, February 17, 2009, 8:11 AM > > On Tue, Feb 17, 2009 at 03:58:45AM -0800, Boris Derzhavets wrote: > > > > It works fine. > > Thank you once again > > > > What kind of hardware are you running on? Which disk controller? > > 64-bit hypervisor/dom0 or 32-bit PAE? > > Would you like to send your dom0 kernel .config ? > > And your grub.conf .. > > Thanks! > > Nice to hear you got itrunning/working!> > -- Pasi > > _______________________________________________ > Xen-devel mailing list > Xen-devel@lists.xensource.com > http://lists.xensource.com/xen-devel_______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
On Wed, Feb 18, 2009 at 5:40 PM, Boris Derzhavets <bderzhavets@yahoo.com> wrote:> Hi Mark, > > I am done with kernel compiled per your advice. > Xen Unstable Dom0 & 2.6.29-rc5 (Xen Dom0 support enabled) loaded fine. > > Thanks, > Boris > > # dmesg > > [ 0.000000] Initializing cgroup subsys cpuset > [ 0.000000] Initializing cgroup subsys cpu > [ 0.000000] Linux version 2.6.29-rc5-tip (root@ServerUbuntu) (gcc version > 4.3.2 (Ubuntu 4.3.2-1ubuntu11) ) #2 SMP Wed Feb 18 12:14:04 EST 2009 > [ 0.000000] Command line: root=/dev/sdb1 ro console=tty0 pci=nomsi > [ 0.000000] KERNEL supported cpus: > [ 0.000000] Intel GenuineIntel > [ 0.000000] AMD AuthenticAMD > [ 0.000000] Centaur CentaurHauls > [ 0.000000] BIOS-provided physical RAM map: > [ 0.000000] Xen: 0000000000000000 - 000000000009ec00 (usable) > [ 0.000000] Xen: 000000000009ec00 - 0000000000100000 (reserved) > [ 0.000000] Xen: 0000000000100000 - 000000000bc1d000 (usable) > [ 0.000000] Xen: 000000000bc1d000 - 000000000be1e000 (reserved) > [ 0.000000] Xen: 000000000be1e000 - 0000000040000000 (usable) > [ 0.000000] Xen: 00000000cff80000 - 00000000cff8e000 (ACPI data) > [ 0.000000] Xen: 00000000cff8e000 - 00000000cffe0000 (ACPI NVS) > [ 0.000000] Xen: 00000000cffe0000 - 00000000d0000000 (reserved) > [ 0.000000] Xen: 00000000fee00000 - 00000000fee01000 (reserved) > [ 0.000000] Xen: 00000000ffe00000 - 0000000100000000 (reserved) > [ 0.000000] DMI 2.4 present. > [ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around > it. > [ 0.000000] last_pfn = 0x40000 max_arch_pfn = 0x100000000 > [ 0.000000] init_memory_mapping: 0000000000000000-0000000040000000 > [ 0.000000] 0000000000 - 0040000000 page 4k > [ 0.000000] kernel direct mapping tables up to 40000000 @ be81000-c083000 > [ 0.000000] last_map_addr: 40000000 end: 40000000 > [ 0.000000] RAMDISK: 008da000 - 0bc1ce00 > [ 0.000000] ACPI: RSDP 000FBB80, 0014 (r0 ACPIAM) > [ 0.000000] ACPI: RSDT CFF80000, 003C (r1 A_M_I_ OEMRSDT 10000730 > MSFT 97) > [ 0.000000] ACPI: FACP CFF80200, 0084 (r2 A_M_I_ OEMFACP 10000730 > MSFT 97) > [ 0.000000] FADT: X_PM1a_EVT_BLK.bit_width (16) does not match > PM1_EVT_LEN (4) > [ 0.000000] ACPI: DSDT CFF805C0, 8E13 (r1 A0840 A0840001 1 INTL > 20060113) > [ 0.000000] ACPI: FACS CFF8E000, 0040 > [ 0.000000] ACPI: APIC CFF80390, 006C (r1 A_M_I_ OEMAPIC 10000730 > MSFT 97) > [ 0.000000] ACPI: MCFG CFF80400, 003C (r1 A_M_I_ OEMMCFG 10000730 > MSFT 97) > [ 0.000000] ACPI: OEMB CFF8E040, 0081 (r1 A_M_I_ AMI_OEM 10000730 > MSFT 97) > [ 0.000000] ACPI: HPET CFF893E0, 0038 (r1 A_M_I_ OEMHPET 10000730 > MSFT 97) > [ 0.000000] ACPI: OSFR CFF89420, 00B0 (r1 A_M_I_ OEMOSFR 10000730 > MSFT 97) > [ 0.000000] ACPI: Local APIC address 0xfee00000 > [ 0.000000] (6 early reservations) ==> bootmem [0000000000 - 0040000000] > [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> > [0000000000 - 0000001000] > [ 0.000000] #1 [000be1e000 - 000be81000] XEN PAGETABLES ==> > [000be1e000 - 000be81000] > [ 0.000000] #2 [0000006000 - 0000008000] TRAMPOLINE ==> > [0000006000 - 0000008000] > [ 0.000000] #3 [0000200000 - 00008d9d20] TEXT DATA BSS ==> > [0000200000 - 00008d9d20] > [ 0.000000] #4 [00008da000 - 000bc1ce00] RAMDISK ==> > [00008da000 - 000bc1ce00] > [ 0.000000] #5 [000be81000 - 000c01d000] PGTABLE ==> > [000be81000 - 000c01d000] > [ 0.000000] found SMP MP-table at [ffff8800000ff780] ff780 > [ 0.000000] Zone PFN ranges: > [ 0.000000] DMA 0x00000010 -> 0x00001000 > [ 0.000000] DMA32 0x00001000 -> 0x00100000 > [ 0.000000] Normal 0x00100000 -> 0x00100000 > [ 0.000000] Movable zone start PFN for each node > [ 0.000000] early_node_map[3] active PFN ranges > [ 0.000000] 0: 0x00000010 -> 0x0000009e > [ 0.000000] 0: 0x00000100 -> 0x0000bc1d > [ 0.000000] 0: 0x0000be1e -> 0x00040000 > [ 0.000000] On node 0 totalpages: 261517 > [ 0.000000] DMA zone: 56 pages used for memmap > [ 0.000000] DMA zone: 1758 pages reserved > [ 0.000000] DMA zone: 2168 pages, LIFO batch:0 > [ 0.000000] DMA32 zone: 3528 pages used for memmap > [ 0.000000] DMA32 zone: 254007 pages, LIFO batch:31 > [ 0.000000] ACPI: PM-Timer IO Port: 0x808 > [ 0.000000] ACPI: Local APIC address 0xfee00000 > [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) > [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) > [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) > [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) > [ 0.000000] IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23 > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) > [ 0.000000] ACPI: IRQ0 used by override. > [ 0.000000] ACPI: IRQ2 used by override. > [ 0.000000] ACPI: IRQ9 used by override. > [ 0.000000] Using ACPI (MADT) for SMP configuration information > [ 0.000000] ACPI: HPET id: 0xffffffff base: 0xfed00000 > [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs > [ 0.000000] nr_irqs_gsi: 24 > [ 0.000000] Allocating PCI resources starting at 50000000 (gap: > 40000000:8ff80000) > [ 0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1 > [ 0.000000] PERCPU: Allocating 86016 bytes of per cpu data > [ 0.000000] trying to map vcpu_info 0 at ffff88000c034020, mfn 21ffcc, > offset 32 > [ 0.000000] cpu 0 using vcpu_info at ffff88000c034020 > [ 0.000000] trying to map vcpu_info 1 at ffff88000c049020, mfn 21ffb7, > offset 32 > [ 0.000000] cpu 1 using vcpu_info at ffff88000c049020 > [ 0.000000] Xen: using vcpu_info placement > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total > pages: 256175 > [ 0.000000] Kernel command line: root=/dev/sdb1 ro console=tty0 pci=nomsi > [ 0.000000] Initializing CPU#0 > [ 0.000000] NR_IRQS:1280 > [ 0.000000] xen: allocated irq 9 for acpi 9 > [ 0.000000] xen_allocate_pirq: returning irq 9 for gsi 9 > [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) > [ 0.000000] Detected 3005.616 MHz processor. > [ 0.010000] Console: colour VGA+ 80x25 > [ 0.010000] console [tty0] enabled > [ 0.010000] Dentry cache hash table entries: 131072 (order: 8, 1048576 > bytes) > [ 0.010000] Inode-cache hash table entries: 65536 (order: 7, 524288 > bytes) > [ 0.010000] allocated 10485760 bytes of page_cgroup > [ 0.010000] please try cgroup_disable=memory option if you don''t want > [ 0.010000] Checking aperture... > [ 0.010000] No AGP bridge found > [ 0.010000] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) > [ 0.010000] xen_swiotlb_fixup: buf=ffff88000daa8000 size=67108864 > [ 0.010000] xen_swiotlb_fixup: buf=ffff880011b08000 size=32768 > [ 0.010000] Placing 64MB software IO TLB between ffff88000daa8000 - > ffff880011aa8000 > [ 0.010000] software IO TLB at phys 0xdaa8000 - 0x11aa8000 > [ 0.010000] Memory: 760356k/1048576k available (3248k kernel code, 2508k > absent, 285004k reserved, 1775k data, 456k init) > [ 0.010000] Xen: using vcpuop timer interface > [ 0.010000] installing Xen timer for CPU 0 > [ 0.010000] Calibrating delay loop (skipped), value calculated using > timer frequency.. 6011.23 BogoMIPS (lpj=30056160) > [ 0.010000] Security Framework initialized > [ 0.010000] SELinux: Disabled at boot. > [ 0.010000] Mount-cache hash table entries: 256 > [ 0.010000] Initializing cgroup subsys ns > [ 0.010000] Initializing cgroup subsys cpuacct > [ 0.010000] Initializing cgroup subsys memory > [ 0.010000] CPU: L1 I cache: 32K, L1 D cache: 32K > [ 0.010000] CPU: L2 cache: 6144K > [ 0.010000] CPU: Physical Processor ID: 0 > [ 0.010000] CPU: Processor Core ID: 0 > [ 0.010000] SMP alternatives: switching to UP code > [ 0.024292] ACPI: Core revision 20081204 > [ 0.040082] cpu 0 spinlock event irq 25 > [ 0.041292] installing Xen timer for CPU 1 > [ 0.041344] cpu 1 spinlock event irq 31 > [ 0.041410] SMP alternatives: switching to SMP code > [ 0.000005] Initializing CPU#1 > [ 0.000038] CPU: L1 I cache: 32K, L1 D cache: 32K > [ 0.000041] CPU: L2 cache: 6144K > [ 0.000044] CPU: Physical Processor ID: 0 > [ 0.000046] CPU: Processor Core ID: 0 > [ 0.077347] Brought up 2 CPUs > [ 0.077593] CPU0 attaching sched-domain: > [ 0.077596] domain 0: span 0-1 level CPU > [ 0.077600] groups: 0 1 > [ 0.077610] CPU1 attaching sched-domain: > [ 0.077612] domain 0: span 0-1 level CPU > [ 0.077616] groups: 1 0 > [ 0.078184] net_namespace: 1840 bytes > [ 0.078230] Booting paravirtualized kernel on Xen > [ 0.078273] Xen version: 3.4-unstable (preserve-AD) (dom0) > [ 0.078453] Grant table initialized > [ 0.078519] Time: 17:25:51 Date: 02/18/09 > [ 0.078614] NET: Registered protocol family 16 > [ 0.079002] xenbus_probe_init ok > [ 0.079309] ACPI: bus type pci registered > [ 0.079875] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - > 255 > [ 0.079923] PCI: Not using MMCONFIG. > [ 0.079965] PCI: Using configuration type 1 for base access > [ 0.082777] bio: create slab <bio-0> at 0 > [ 0.085729] ACPI: EC: Look up EC in DSDT > [ 0.100205] ACPI: Interpreter enabled > [ 0.100249] ACPI: (supports S0 S1 S3 S5) > [ 0.100433] ACPI: Using IOAPIC for interrupt routing > [ 0.100533] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - > 255 > [ 0.103872] PCI: MCFG area at e0000000 reserved in ACPI motherboard > resources > [ 0.165824] PCI: Using MMCONFIG at e0000000 - efffffff > [ 0.181128] ACPI: No dock devices found. > [ 0.181237] ACPI: PCI Root Bridge [PCI0] (0000:00) > [ 0.181565] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold > [ 0.181614] pci 0000:00:01.0: PME# disabled > [ 0.181799] pci 0000:00:1a.0: reg 20 io port: [0xa800-0xa81f] > [ 0.181935] pci 0000:00:1a.1: reg 20 io port: [0xa880-0xa89f] > [ 0.182070] pci 0000:00:1a.2: reg 20 io port: [0xac00-0xac1f] > [ 0.182210] pci 0000:00:1a.7: reg 10 32bit mmio: [0xf9fffc00-0xf9ffffff] > [ 0.182314] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold > [ 0.182363] pci 0000:00:1a.7: PME# disabled > [ 0.182482] pci 0000:00:1b.0: reg 10 64bit mmio: [0xf9ff8000-0xf9ffbfff] > [ 0.182568] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold > [ 0.182617] pci 0000:00:1b.0: PME# disabled > [ 0.182773] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold > [ 0.182822] pci 0000:00:1c.0: PME# disabled > [ 0.182987] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold > [ 0.183036] pci 0000:00:1c.4: PME# disabled > [ 0.183195] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold > [ 0.183244] pci 0000:00:1c.5: PME# disabled > [ 0.183389] pci 0000:00:1d.0: reg 20 io port: [0xa080-0xa09f] > [ 0.183528] pci 0000:00:1d.1: reg 20 io port: [0xa400-0xa41f] > [ 0.183663] pci 0000:00:1d.2: reg 20 io port: [0xa480-0xa49f] > [ 0.183803] pci 0000:00:1d.7: reg 10 32bit mmio: [0xf9fff800-0xf9fffbff] > [ 0.183906] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold > [ 0.183956] pci 0000:00:1d.7: PME# disabled > [ 0.184220] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 > ACPI/GPIO/TCO > [ 0.184277] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 > GPIO > [ 0.184325] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0294 > (mask 0003) > [ 0.184505] pci 0000:00:1f.2: reg 10 io port: [0x9c00-0x9c07] > [ 0.184515] pci 0000:00:1f.2: reg 14 io port: [0x9880-0x9883] > [ 0.184526] pci 0000:00:1f.2: reg 18 io port: [0x9800-0x9807] > [ 0.184536] pci 0000:00:1f.2: reg 1c io port: [0x9480-0x9483] > [ 0.184547] pci 0000:00:1f.2: reg 20 io port: [0x9400-0x941f] > [ 0.184557] pci 0000:00:1f.2: reg 24 32bit mmio: [0xf9ffe800-0xf9ffefff] > [ 0.184623] pci 0000:00:1f.2: PME# supported from D3hot > [ 0.184671] pci 0000:00:1f.2: PME# disabled > [ 0.184769] pci 0000:00:1f.3: reg 10 64bit mmio: [0xf9fff400-0xf9fff4ff] > [ 0.184795] pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f] > [ 0.184890] pci 0000:01:00.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff] > [ 0.184908] pci 0000:01:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff] > [ 0.184927] pci 0000:01:00.0: reg 1c 64bit mmio: [0xfa000000-0xfbffffff] > [ 0.184937] pci 0000:01:00.0: reg 24 io port: [0xbc00-0xbc7f] > [ 0.184947] pci 0000:01:00.0: reg 30 32bit mmio: [0xfe8e0000-0xfe8fffff] > [ 0.185073] pci 0000:00:01.0: bridge io port: [0xb000-0xbfff] > [ 0.185079] pci 0000:00:01.0: bridge 32bit mmio: [0xfa000000-0xfe8fffff] > [ 0.185088] pci 0000:00:01.0: bridge 64bit mmio pref: > [0xd0000000-0xdfffffff] > [ 0.185179] pci 0000:00:1c.0: bridge 64bit mmio pref: > [0xf8f00000-0xf8ffffff] > [ 0.185324] pci 0000:03:00.0: reg 24 32bit mmio: [0xfeafe000-0xfeafffff] > [ 0.185338] pci 0000:03:00.0: reg 30 32bit mmio: [0xfeae0000-0xfeaeffff] > [ 0.185389] pci 0000:03:00.0: PME# supported from D3hot > [ 0.185438] pci 0000:03:00.0: PME# disabled > [ 0.185560] pci 0000:03:00.1: reg 10 io port: [0xdc00-0xdc07] > [ 0.185574] pci 0000:03:00.1: reg 14 io port: [0xd880-0xd883] > [ 0.185588] pci 0000:03:00.1: reg 18 io port: [0xd800-0xd807] > [ 0.185601] pci 0000:03:00.1: reg 1c io port: [0xd480-0xd483] > [ 0.185615] pci 0000:03:00.1: reg 20 io port: [0xd400-0xd40f] > [ 0.185775] pci 0000:00:1c.4: bridge io port: [0xd000-0xdfff] > [ 0.185782] pci 0000:00:1c.4: bridge 32bit mmio: [0xfea00000-0xfeafffff] > [ 0.185889] pci 0000:02:00.0: reg 10 64bit mmio: [0xfe9fc000-0xfe9fffff] > [ 0.185902] pci 0000:02:00.0: reg 18 io port: [0xc800-0xc8ff] > [ 0.185945] pci 0000:02:00.0: reg 30 32bit mmio: [0xfe9c0000-0xfe9dffff] > [ 0.186013] pci 0000:02:00.0: supports D1 D2 > [ 0.186015] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold > [ 0.186066] pci 0000:02:00.0: PME# disabled > [ 0.186188] pci 0000:00:1c.5: bridge io port: [0xc000-0xcfff] > [ 0.186195] pci 0000:00:1c.5: bridge 32bit mmio: [0xfe900000-0xfe9fffff] > [ 0.186272] pci 0000:05:03.0: reg 10 32bit mmio: [0xfebff000-0xfebfffff] > [ 0.186359] pci 0000:05:03.0: supports D1 D2 > [ 0.186362] pci 0000:05:03.0: PME# supported from D0 D1 D2 D3hot > [ 0.186411] pci 0000:05:03.0: PME# disabled > [ 0.186512] pci 0000:05:04.0: reg 10 io port: [0xe800-0xe8ff] > [ 0.186524] pci 0000:05:04.0: reg 14 32bit mmio: [0xfebfec00-0xfebfecff] > [ 0.186571] pci 0000:05:04.0: reg 30 32bit mmio: [0xfebc0000-0xfebdffff] > [ 0.186605] pci 0000:05:04.0: supports D1 D2 > [ 0.186608] pci 0000:05:04.0: PME# supported from D1 D2 D3hot D3cold > [ 0.186657] pci 0000:05:04.0: PME# disabled > [ 0.186771] pci 0000:00:1e.0: transparent bridge > [ 0.186818] pci 0000:00:1e.0: bridge io port: [0xe000-0xefff] > [ 0.186825] pci 0000:00:1e.0: bridge 32bit mmio: [0xfeb00000-0xfebfffff] > [ 0.186877] pci_bus 0000:00: on NUMA node 0 > [ 0.186884] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > [ 0.187092] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT] > [ 0.187165] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] > [ 0.187324] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] > [ 0.187404] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT] > [ 0.187486] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT] > [ 0.210324] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 > 15) > [ 0.210855] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 > 15) > [ 0.211383] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 > 15) > [ 0.211911] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 *14 > 15) > [ 0.212439] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 > 15) *0, disabled. > [ 0.213035] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 10 11 12 14 > 15) > [ 0.213562] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 > *15) > [ 0.214090] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 > 15) > [ 0.214709] ACPI Warning (tbutils-0242): Incorrect checksum in table > [OEMB] - 67, should be 5E [20081204] > [ 0.214909] xen_balloon: Initialising balloon driver. > [ 0.215415] SCSI subsystem initialized > [ 0.215558] libata version 3.00 loaded. > [ 0.215989] PCI: Using ACPI for IRQ routing > [ 0.240025] NET: Registered protocol family 8 > [ 0.240077] NET: Registered protocol family 20 > [ 0.240186] NetLabel: Initializing > [ 0.240228] NetLabel: domain hash size = 128 > [ 0.240271] NetLabel: protocols = UNLABELED CIPSOv4 > [ 0.240327] NetLabel: unlabeled traffic allowed by default > [ 0.241162] Xen: Initializing Xen DMA ops > [ 0.241205] Xen: Enabling DMA fallback to swiotlb > [ 0.280025] pnp: PnP ACPI init > [ 0.280088] ACPI: bus type pnp registered > [ 0.280634] xen: registering gsi 8 triggering 1 polarity 0 > [ 0.280638] xen_allocate_pirq: returning irq 8 for gsi 8 > [ 0.280682] xen: --> irq=8 > [ 0.280686] xen_set_ioapic_routing: irq 8 gsi 8 vector 80 ioapic 0 pin 8 > triggering 1 polarity 0 > [ 0.280913] xen: registering gsi 13 triggering 1 polarity 0 > [ 0.280916] xen_allocate_pirq: returning irq 13 for gsi 13 > [ 0.280960] xen: --> irq=13 > [ 0.280963] xen_set_ioapic_routing: irq 13 gsi 13 vector 120 ioapic 0 pin > 13 triggering 1 polarity 0 > [ 0.281781] xen: registering gsi 6 triggering 1 polarity 0 > [ 0.281784] xen_allocate_pirq: returning irq 6 for gsi 6 > [ 0.281829] xen: --> irq=6 > [ 0.281832] xen_set_ioapic_routing: irq 6 gsi 6 vector 64 ioapic 0 pin 6 > triggering 1 polarity 0 > [ 0.283363] xen: registering gsi 4 triggering 1 polarity 0 > [ 0.283366] xen_allocate_pirq: returning irq 4 for gsi 4 > [ 0.283410] xen: --> irq=4 > [ 0.283413] xen_set_ioapic_routing: irq 4 gsi 4 vector 48 ioapic 0 pin 4 > triggering 1 polarity 0 > [ 0.284436] xen: registering gsi 1 triggering 1 polarity 0 > [ 0.284439] xen_allocate_pirq: returning irq 1 for gsi 1 > [ 0.284484] xen: --> irq=1 > [ 0.284486] xen_set_ioapic_routing: irq 1 gsi 1 vector 32 ioapic 0 pin 1 > triggering 1 polarity 0 > [ 0.286099] pnp: PnP ACPI: found 15 devices > [ 0.286144] ACPI: ACPI bus type pnp unregistered > [ 0.286197] system 00:01: iomem range 0xfed14000-0xfed19fff has been > reserved > [ 0.286251] system 00:07: ioport range 0x290-0x297 has been reserved > [ 0.286302] system 00:08: ioport range 0x4d0-0x4d1 has been reserved > [ 0.286347] system 00:08: ioport range 0x800-0x87f has been reserved > [ 0.286393] system 00:08: ioport range 0x480-0x4bf has been reserved > [ 0.286438] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been > reserved > [ 0.286485] system 00:08: iomem range 0xfed20000-0xfed3ffff has been > reserved > [ 0.286531] system 00:08: iomem range 0xfed50000-0xfed8ffff has been > reserved > [ 0.286577] system 00:08: iomem range 0xffa00000-0xffafffff has been > reserved > [ 0.286623] system 00:08: iomem range 0xffb00000-0xffbfffff has been > reserved > [ 0.286669] system 00:08: iomem range 0xffe00000-0xffefffff has been > reserved > [ 0.286716] system 00:08: iomem range 0xfff00000-0xfffffffe has been > reserved > [ 0.286767] system 00:0b: iomem range 0xfec00000-0xfec00fff has been > reserved > [ 0.286814] system 00:0b: iomem range 0xfee00000-0xfee00fff has been > reserved > [ 0.286865] system 00:0d: iomem range 0xe0000000-0xefffffff has been > reserved > [ 0.286916] system 00:0e: iomem range 0x0-0x9ffff could not be reserved > [ 0.286962] system 00:0e: iomem range 0xc0000-0xcffff could not be > reserved > [ 0.287008] system 00:0e: iomem range 0xe0000-0xfffff could not be > reserved > [ 0.287054] system 00:0e: iomem range 0x100000-0xcfffffff could not be > reserved > [ 0.292348] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 > [ 0.292395] pci 0000:00:01.0: IO window: 0xb000-0xbfff > [ 0.292445] pci 0000:00:01.0: MEM window: 0xfa000000-0xfe8fffff > [ 0.292493] pci 0000:00:01.0: PREFETCH window: > 0x000000d0000000-0x000000dfffffff > [ 0.292555] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:04 > [ 0.292599] pci 0000:00:1c.0: IO window: disabled > [ 0.292648] pci 0000:00:1c.0: MEM window: disabled > [ 0.292696] pci 0000:00:1c.0: PREFETCH window: > 0x000000f8f00000-0x000000f8ffffff > [ 0.292759] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:03 > [ 0.292806] pci 0000:00:1c.4: IO window: 0xd000-0xdfff > [ 0.292856] pci 0000:00:1c.4: MEM window: 0xfea00000-0xfeafffff > [ 0.292904] pci 0000:00:1c.4: PREFETCH window: disabled > [ 0.292956] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:02 > [ 0.293003] pci 0000:00:1c.5: IO window: 0xc000-0xcfff > [ 0.293053] pci 0000:00:1c.5: MEM window: 0xfe900000-0xfe9fffff > [ 0.293101] pci 0000:00:1c.5: PREFETCH window: disabled > [ 0.293154] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05 > [ 0.293201] pci 0000:00:1e.0: IO window: 0xe000-0xefff > [ 0.293251] pci 0000:00:1e.0: MEM window: 0xfeb00000-0xfebfffff > [ 0.293299] pci 0000:00:1e.0: PREFETCH window: > 0x00000050000000-0x000000500fffff > [ 0.293370] xen: registering gsi 16 triggering 0 polarity 1 > [ 0.293380] xen: --> irq=16 > [ 0.293382] xen_set_ioapic_routing: irq 16 gsi 16 vector 160 ioapic 0 pin > 16 triggering 0 polarity 1 > [ 0.293443] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > [ 0.293492] pci 0000:00:01.0: setting latency timer to 64 > [ 0.293504] xen: registering gsi 17 triggering 0 polarity 1 > [ 0.293510] xen: --> irq=17 > [ 0.293513] xen_set_ioapic_routing: irq 17 gsi 17 vector 168 ioapic 0 pin > 17 triggering 0 polarity 1 > [ 0.293573] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 > [ 0.293622] pci 0000:00:1c.0: setting latency timer to 64 > [ 0.293634] xen: registering gsi 17 triggering 0 polarity 1 > [ 0.293637] xen_allocate_pirq: returning irq 17 for gsi 17 > [ 0.293681] xen: --> irq=17 > [ 0.293684] xen_set_ioapic_routing: irq 17 gsi 17 vector 168 ioapic 0 pin > 17 triggering 0 polarity 1 > [ 0.293742] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17 > [ 0.293791] pci 0000:00:1c.4: setting latency timer to 64 > [ 0.293803] xen: registering gsi 16 triggering 0 polarity 1 > [ 0.293806] xen_allocate_pirq: returning irq 16 for gsi 16 > [ 0.293850] xen: --> irq=16 > [ 0.293852] xen_set_ioapic_routing: irq 16 gsi 16 vector 160 ioapic 0 pin > 16 triggering 0 polarity 1 > [ 0.293911] pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16 > [ 0.293960] pci 0000:00:1c.5: setting latency timer to 64 > [ 0.293972] pci 0000:00:1e.0: setting latency timer to 64 > [ 0.293977] pci_bus 0000:00: resource 0 io: [0x00-0xffff] > [ 0.293980] pci_bus 0000:00: resource 1 mem: > [0x000000-0xffffffffffffffff] > [ 0.293983] pci_bus 0000:01: resource 0 io: [0xb000-0xbfff] > [ 0.293985] pci_bus 0000:01: resource 1 mem: [0xfa000000-0xfe8fffff] > [ 0.293988] pci_bus 0000:01: resource 2 mem: [0xd0000000-0xdfffffff] > [ 0.293991] pci_bus 0000:01: resource 3 mem: [0x0-0x0] > [ 0.293993] pci_bus 0000:04: resource 0 mem: [0x0-0x0] > [ 0.293996] pci_bus 0000:04: resource 1 mem: [0x0-0x0] > [ 0.293998] pci_bus 0000:04: resource 2 mem: [0xf8f00000-0xf8ffffff] > [ 0.294001] pci_bus 0000:04: resource 3 mem: [0x0-0x0] > [ 0.294004] pci_bus 0000:03: resource 0 io: [0xd000-0xdfff] > [ 0.294006] pci_bus 0000:03: resource 1 mem: [0xfea00000-0xfeafffff] > [ 0.294009] pci_bus 0000:03: resource 2 mem: [0x0-0x0] > [ 0.294011] pci_bus 0000:03: resource 3 mem: [0x0-0x0] > [ 0.294014] pci_bus 0000:02: resource 0 io: [0xc000-0xcfff] > [ 0.294017] pci_bus 0000:02: resource 1 mem: [0xfe900000-0xfe9fffff] > [ 0.294019] pci_bus 0000:02: resource 2 mem: [0x0-0x0] > [ 0.294022] pci_bus 0000:02: resource 3 mem: [0x0-0x0] > [ 0.294025] pci_bus 0000:05: resource 0 io: [0xe000-0xefff] > [ 0.294027] pci_bus 0000:05: resource 1 mem: [0xfeb00000-0xfebfffff] > [ 0.294030] pci_bus 0000:05: resource 2 mem: [0x50000000-0x500fffff] > [ 0.294033] pci_bus 0000:05: resource 3 io: [0x00-0xffff] > [ 0.294035] pci_bus 0000:05: resource 4 mem: > [0x000000-0xffffffffffffffff] > [ 0.294096] NET: Registered protocol family 2 > [ 0.420127] IP route cache hash table entries: 32768 (order: 6, 262144 > bytes) > [ 0.420568] TCP established hash table entries: 131072 (order: 9, 2097152 > bytes) > [ 0.421132] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) > [ 0.421440] TCP: Hash tables configured (established 131072 bind 65536) > [ 0.421485] TCP reno registered > [ 0.460139] NET: Registered protocol family 1 > [ 0.460302] checking if image is initramfs... it is > [ 0.583284] Freeing initrd memory: 183563k freed > [ 0.644751] audit: initializing netlink socket (disabled) > [ 0.644820] type=2000 audit(1234977952.276:1): initialized > [ 0.649413] VFS: Disk quotas dquot_6.5.2 > [ 0.649509] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) > [ 0.649616] msgmni has been set to 2406 > [ 0.649860] alg: No test for stdrng (krng) > [ 0.649923] io scheduler noop registered > [ 0.649967] io scheduler anticipatory registered > [ 0.650013] io scheduler deadline registered (default) > [ 0.650104] io scheduler cfq registered > [ 0.650365] pci 0000:01:00.0: Boot video device > [ 0.650563] pcieport-driver 0000:00:01.0: setting latency timer to 64 > [ 0.650849] pcieport-driver 0000:00:1c.0: setting latency timer to 64 > [ 0.651168] pcieport-driver 0000:00:1c.4: setting latency timer to 64 > [ 0.651488] pcieport-driver 0000:00:1c.5: setting latency timer to 64 > [ 0.652221] xenbus_probe_backend_init bus registered ok > [ 0.652319] xenbus_probe_frontend_init bus registered ok > [ 0.652434] Event-channel device installed. > [ 0.652477] ***blkif_init > [ 0.654589] *** netif_init > [ 0.655343] registering netback > [ 0.696151] Linux agpgart interface v0.103 > [ 0.698363] brd: module loaded > [ 0.698551] input: Macintosh mouse button emulation as > /devices/virtual/input/input0 > [ 0.698643] ahci 0000:00:1f.2: version 3.0 > [ 0.698662] xen: registering gsi 22 triggering 0 polarity 1 > [ 0.698673] xen: --> irq=22 > [ 0.698677] xen_set_ioapic_routing: irq 22 gsi 22 vector 176 ioapic 0 pin > 22 triggering 0 polarity 1 > [ 0.698738] ahci 0000:00:1f.2: PCI INT B -> GSI 22 (level, low) -> IRQ 22 > [ 0.698867] ahci: SSS flag set, parallel bus scan disabled > [ 0.698939] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps > 0x3f impl SATA mode > [ 0.698996] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pmp > pio slum part ems > [ 0.699056] ahci 0000:00:1f.2: setting latency timer to 64 > [ 0.699667] scsi0 : ahci > [ 0.699907] scsi1 : ahci > [ 0.700201] scsi2 : ahci > [ 0.700402] scsi3 : ahci > [ 0.700597] scsi4 : ahci > [ 0.700799] scsi5 : ahci > [ 0.701165] ata1: SATA max UDMA/133 abar m2048@0xf9ffe800 port 0xf9ffe900 > irq 22 > [ 0.701222] ata2: SATA max UDMA/133 abar m2048@0xf9ffe800 port 0xf9ffe980 > irq 22 > [ 0.701277] ata3: SATA max UDMA/133 abar m2048@0xf9ffe800 port 0xf9ffea00 > irq 22 > [ 0.701332] ata4: SATA max UDMA/133 abar m2048@0xf9ffe800 port 0xf9ffea80 > irq 22 > [ 0.701387] ata5: SATA max UDMA/133 abar m2048@0xf9ffe800 port 0xf9ffeb00 > irq 22 > [ 0.701442] ata6: SATA max UDMA/133 abar m2048@0xf9ffe800 port 0xf9ffeb80 > irq 22 > [ 1.230022] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) > [ 1.230656] ata1.00: ATA-7: ST3250410AS, 3.AAC, max UDMA/133 > [ 1.230708] ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32) > [ 1.231428] ata1.00: configured for UDMA/133 > [ 1.250139] scsi 0:0:0:0: Direct-Access ATA ST3250410AS > 3.AA PQ: 0 ANSI: 5 > [ 1.780022] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) > [ 1.780611] ata2.00: ATA-7: ST3250410AS, 3.AAC, max UDMA/133 > [ 1.780662] ata2.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32) > [ 1.781409] ata2.00: configured for UDMA/133 > [ 1.800123] scsi 1:0:0:0: Direct-Access ATA ST3250410AS > 3.AA PQ: 0 ANSI: 5 > [ 2.150025] ata3: SATA link down (SStatus 0 SControl 300) > [ 2.520024] ata4: SATA link down (SStatus 0 SControl 300) > [ 2.890024] ata5: SATA link down (SStatus 0 SControl 300) > [ 3.260023] ata6: SATA link down (SStatus 0 SControl 300) > [ 3.280062] xen: registering gsi 16 triggering 0 polarity 1 > [ 3.280067] xen_allocate_pirq: returning irq 16 for gsi 16 > [ 3.280122] xen: --> irq=16 > [ 3.280125] xen_set_ioapic_routing: irq 16 gsi 16 vector 160 ioapic 0 pin > 16 triggering 0 polarity 1 > [ 3.280184] ahci 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > [ 3.300046] ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 > impl SATA mode > [ 3.300116] ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum > part > [ 3.300168] ahci 0000:03:00.0: setting latency timer to 64 > [ 3.300380] scsi6 : ahci > [ 3.300580] scsi7 : ahci > [ 3.300807] ata7: SATA max UDMA/133 abar m8192@0xfeafe000 port 0xfeafe100 > irq 16 > [ 3.300864] ata8: SATA max UDMA/133 abar m8192@0xfeafe000 port 0xfeafe180 > irq 16 > [ 3.650044] ata7: SATA link down (SStatus 0 SControl 300) > [ 4.020035] ata8: SATA link down (SStatus 0 SControl 300) > [ 4.040225] pata_jmicron 0000:03:00.1: enabling device (0000 -> 0001) > [ 4.040274] xen: registering gsi 17 triggering 0 polarity 1 > [ 4.040277] xen_allocate_pirq: returning irq 17 for gsi 17 > [ 4.040321] xen: --> irq=17 > [ 4.040323] xen_set_ioapic_routing: irq 17 gsi 17 vector 168 ioapic 0 pin > 17 triggering 0 polarity 1 > [ 4.040382] pata_jmicron 0000:03:00.1: PCI INT B -> GSI 17 (level, low) > -> IRQ 17 > [ 4.040472] pata_jmicron 0000:03:00.1: setting latency timer to 64 > [ 4.040563] scsi8 : pata_jmicron > [ 4.040757] scsi9 : pata_jmicron > [ 4.041922] ata9: PATA max UDMA/100 cmd 0xdc00 ctl 0xd880 bmdma 0xd400 > irq 17 > [ 4.041969] ata10: PATA max UDMA/100 cmd 0xd800 ctl 0xd480 bmdma 0xd408 > irq 17 > [ 4.220580] ata9.00: ATAPI: Optiarc DVD RW AD-5200A, 1.03, max UDMA/66 > [ 4.260586] ata9.00: configured for UDMA/66 > [ 4.264257] scsi 8:0:0:0: CD-ROM Optiarc DVD RW AD-5200A > 1.03 PQ: 0 ANSI: 5 > [ 4.432024] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 > [ 4.432070] PNP: PS/2 appears to have AUX port disabled, if this is > incorrect please boot with i8042.nopnp > [ 4.432692] serio: i8042 KBD port at 0x60,0x64 irq 1 > [ 4.460188] mice: PS/2 mouse device common for all mice > [ 4.460320] rtc_cmos 00:03: RTC can wake from S4 > [ 4.460452] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 > [ 4.460520] rtc0: alarms up to one month, y3k, 114 bytes nvram > [ 4.460618] cpuidle: using governor ladder > [ 4.461165] TCP cubic registered > [ 4.461258] Bridge firewalling registered > [ 4.461330] IO APIC resources could be not be allocated. > [ 4.461585] registered taskstats version 1 > [ 4.461765] Magic number: 13:504:441 > [ 4.461913] rtc_cmos 00:03: setting system clock to 2009-02-18 17:25:55 > UTC (1234977955) > [ 4.461970] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found > [ 4.462014] EDD information not available. > [ 4.462101] Freeing unused kernel memory: 456k freed > [ 4.462291] Write protecting the kernel read-only data: 4652k > [ 4.479099] input: AT Translated Set 2 keyboard as > /devices/platform/i8042/serio0/input/input1 > [ 4.567451] fuse init (API version 7.11) > [ 4.595928] device-mapper: uevent: version 1.0.3 > [ 4.596145] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: > dm-devel@redhat.com > [ 4.849829] usbcore: registered new interface driver usbfs > [ 4.849901] usbcore: registered new interface driver hub > [ 4.860789] usbcore: registered new device driver usb > [ 4.863262] uhci_hcd: USB Universal Host Controller Interface driver > [ 4.863349] xen: registering gsi 16 triggering 0 polarity 1 > [ 4.863353] xen_allocate_pirq: returning irq 16 for gsi 16 > [ 4.863397] xen: --> irq=16 > [ 4.863400] xen_set_ioapic_routing: irq 16 gsi 16 vector 160 ioapic 0 pin > 16 triggering 0 polarity 1 > [ 4.863461] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> > IRQ 16 > [ 4.863516] uhci_hcd 0000:00:1a.0: setting latency timer to 64 > [ 4.863522] uhci_hcd 0000:00:1a.0: UHCI Host Controller > [ 4.863608] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus > number 1 > [ 4.863691] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000a800 > [ 4.863991] usb usb1: configuration #1 chosen from 1 choice > [ 4.864063] hub 1-0:1.0: USB hub found > [ 4.864118] hub 1-0:1.0: 2 ports detected > [ 4.864298] xen: registering gsi 21 triggering 0 polarity 1 > [ 4.864308] xen: --> irq=21 > [ 4.864311] xen_set_ioapic_routing: irq 21 gsi 21 vector 184 ioapic 0 pin > 21 triggering 0 polarity 1 > [ 4.864371] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> > IRQ 21 > [ 4.864423] uhci_hcd 0000:00:1a.1: setting latency timer to 64 > [ 4.864428] uhci_hcd 0000:00:1a.1: UHCI Host Controller > [ 4.864495] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus > number 2 > [ 4.864593] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000a880 > [ 4.864748] usb usb2: configuration #1 chosen from 1 choice > [ 4.864821] hub 2-0:1.0: USB hub found > [ 4.864875] hub 2-0:1.0: 2 ports detected > [ 4.865033] xen: registering gsi 18 triggering 0 polarity 1 > [ 4.865039] xen: --> irq=18 > [ 4.865042] xen_set_ioapic_routing: irq 18 gsi 18 vector 192 ioapic 0 pin > 18 triggering 0 polarity 1 > [ 4.865101] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 18 (level, low) -> > IRQ 18 > [ 4.865153] uhci_hcd 0000:00:1a.2: setting latency timer to 64 > [ 4.865158] uhci_hcd 0000:00:1a.2: UHCI Host Controller > [ 4.865224] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus > number 3 > [ 4.865314] uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000ac00 > [ 4.865485] usb usb3: configuration #1 chosen from 1 choice > [ 4.865576] hub 3-0:1.0: USB hub found > [ 4.865633] hub 3-0:1.0: 2 ports detected > [ 4.865803] xen: registering gsi 23 triggering 0 polarity 1 > [ 4.865811] xen: --> irq=23 > [ 4.865814] xen_set_ioapic_routing: irq 23 gsi 23 vector 200 ioapic 0 pin > 23 triggering 0 polarity 1 > [ 4.865874] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> > IRQ 23 > [ 4.865927] uhci_hcd 0000:00:1d.0: setting latency timer to 64 > [ 4.865932] uhci_hcd 0000:00:1d.0: UHCI Host Controller > [ 4.866005] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus > number 4 > [ 4.866101] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000a080 > [ 4.866259] usb usb4: configuration #1 chosen from 1 choice > [ 4.866336] hub 4-0:1.0: USB hub found > [ 4.866396] hub 4-0:1.0: 2 ports detected > [ 4.866558] xen: registering gsi 19 triggering 0 polarity 1 > [ 4.866565] xen: --> irq=19 > [ 4.866568] xen_set_ioapic_routing: irq 19 gsi 19 vector 208 ioapic 0 pin > 19 triggering 0 polarity 1 > [ 4.866628] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> > IRQ 19 > [ 4.866680] uhci_hcd 0000:00:1d.1: setting latency timer to 64 > [ 4.866685] uhci_hcd 0000:00:1d.1: UHCI Host Controller > [ 4.866753] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus > number 5 > [ 4.866846] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000a400 > [ 4.867019] usb usb5: configuration #1 chosen from 1 choice > [ 4.867095] hub 5-0:1.0: USB hub found > [ 4.867152] hub 5-0:1.0: 2 ports detected > [ 4.867308] xen: registering gsi 18 triggering 0 polarity 1 > [ 4.867311] xen_allocate_pirq: returning irq 18 for gsi 18 > [ 4.867356] xen: --> irq=18 > [ 4.867359] xen_set_ioapic_routing: irq 18 gsi 18 vector 192 ioapic 0 pin > 18 triggering 0 polarity 1 > [ 4.867421] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> > IRQ 18 > [ 4.867477] uhci_hcd 0000:00:1d.2: setting latency timer to 64 > [ 4.867482] uhci_hcd 0000:00:1d.2: UHCI Host Controller > [ 4.867552] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus > number 6 > [ 4.867638] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000a480 > [ 4.867800] usb usb6: configuration #1 chosen from 1 choice > [ 4.867873] hub 6-0:1.0: USB hub found > [ 4.867929] hub 6-0:1.0: 2 ports detected > [ 4.870567] ehci_hcd: USB 2.0 ''Enhanced'' Host Controller (EHCI) Driver > [ 4.870615] Warning! ehci_hcd should always be loaded before uhci_hcd and > ohci_hcd, not after > [ 4.870694] xen: registering gsi 18 triggering 0 polarity 1 > [ 4.870697] xen_allocate_pirq: returning irq 18 for gsi 18 > [ 4.870745] xen: --> irq=18 > [ 4.870748] xen_set_ioapic_routing: irq 18 gsi 18 vector 192 ioapic 0 pin > 18 triggering 0 polarity 1 > [ 4.870812] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> > IRQ 18 > [ 4.870878] ehci_hcd 0000:00:1a.7: setting latency timer to 64 > [ 4.870884] ehci_hcd 0000:00:1a.7: EHCI Host Controller > [ 4.870956] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus > number 7 > [ 4.874937] ehci_hcd 0000:00:1a.7: debug port 1 > [ 4.874989] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported > [ 4.874997] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf9fffc00 > [ 4.890098] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 > [ 4.890292] usb usb7: configuration #1 chosen from 1 choice > [ 4.890370] hub 7-0:1.0: USB hub found > [ 4.890431] hub 7-0:1.0: 6 ports detected > [ 4.890628] xen: registering gsi 23 triggering 0 polarity 1 > [ 4.890631] xen_allocate_pirq: returning irq 23 for gsi 23 > [ 4.890678] xen: --> irq=23 > [ 4.890681] xen_set_ioapic_routing: irq 23 gsi 23 vector 200 ioapic 0 pin > 23 triggering 0 polarity 1 > [ 4.890743] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> > IRQ 23 > [ 4.890806] ehci_hcd 0000:00:1d.7: setting latency timer to 64 > [ 4.890813] ehci_hcd 0000:00:1d.7: EHCI Host Controller > [ 4.890887] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus > number 8 > [ 4.894865] ehci_hcd 0000:00:1d.7: debug port 1 > [ 4.894916] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported > [ 4.894924] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf9fff800 > [ 4.900994] scsi 0:0:0:0: Attached scsi generic sg0 type 0 > [ 4.901079] scsi 1:0:0:0: Attached scsi generic sg1 type 0 > [ 4.901170] scsi 8:0:0:0: Attached scsi generic sg2 type 5 > [ 4.910925] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 > [ 4.911109] usb usb8: configuration #1 chosen from 1 choice > [ 4.911185] hub 8-0:1.0: USB hub found > [ 4.911398] hub 8-0:1.0: 6 ports detected > [ 4.929585] sky2 driver version 1.22 > [ 4.929673] xen: registering gsi 17 triggering 0 polarity 1 > [ 4.929676] xen_allocate_pirq: returning irq 17 for gsi 17 > [ 4.929721] xen: --> irq=17 > [ 4.929725] xen_set_ioapic_routing: irq 17 gsi 17 vector 168 ioapic 0 pin > 17 triggering 0 polarity 1 > [ 4.929787] sky2 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 > [ 4.929845] sky2 0000:02:00.0: setting latency timer to 64 > [ 4.929889] sky2 0000:02:00.0: Yukon-2 EC Ultra chip revision 3 > [ 4.962126] sky2 0000:02:00.0: Marvell Yukon 88E8056 Gigabit Ethernet > Controller > [ 4.962186] Part Number: Yukon 88E8056 > [ 4.962188] Engineering Level: Rev. 1.2 > [ 4.962191] Manufacturer: Marvell > [ 4.962572] sky2 eth0: addr 00:1e:8c:25:d9:23 > [ 5.015015] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded > [ 5.015082] xen: registering gsi 16 triggering 0 polarity 1 > [ 5.015085] xen_allocate_pirq: returning irq 16 for gsi 16 > [ 5.015130] xen: --> irq=16 > [ 5.015133] xen_set_ioapic_routing: irq 16 gsi 16 vector 160 ioapic 0 pin > 16 triggering 0 polarity 1 > [ 5.015197] r8169 0000:05:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ > 16 > [ 5.015283] r8169 0000:05:04.0: no PCI Express capability > [ 5.015750] eth1: RTL8169sc/8110sc at 0xffffc20000056c00, > 00:1e:8c:25:cc:a5, XID 18000000 IRQ 16 > [ 5.020915] xen: registering gsi 19 triggering 0 polarity 1 > [ 5.020920] xen_allocate_pirq: returning irq 19 for gsi 19 > [ 5.020967] xen: --> irq=19 > [ 5.020971] xen_set_ioapic_routing: irq 19 gsi 19 vector 208 ioapic 0 pin > 19 triggering 0 polarity 1 > [ 5.021032] ohci1394 0000:05:03.0: PCI INT A -> GSI 19 (level, low) -> > IRQ 19 > [ 5.025107] Driver ''sr'' needs updating - please use bus_type methods > [ 5.030286] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray > [ 5.030334] Uniform CD-ROM driver Revision: 3.20 > [ 5.030473] sr 8:0:0:0: Attached scsi CD-ROM sr0 > [ 5.036150] Driver ''sd'' needs updating - please use bus_type methods > [ 5.036299] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 > GB/232 GiB) > [ 5.036377] sd 0:0:0:0: [sda] Write Protect is off > [ 5.036422] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 5.036464] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, > doesn''t support DPO or FUA > [ 5.036597] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 > GB/232 GiB) > [ 5.036674] sd 0:0:0:0: [sda] Write Protect is off > [ 5.036718] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 5.036761] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, > doesn''t support DPO or FUA > [ 5.036821] sda: sda1 sda2 sda3 sda4 < > > [ 5.054561] sd 0:0:0:0: [sda] Attached SCSI disk > [ 5.054684] sd 1:0:0:0: [sdb] 488397168 512-byte hardware sectors: (250 > GB/232 GiB) > [ 5.054761] sd 1:0:0:0: [sdb] Write Protect is off > [ 5.054806] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 > [ 5.054848] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, > doesn''t support DPO or FUA > [ 5.054972] sd 1:0:0:0: [sdb] 488397168 512-byte hardware sectors: (250 > GB/232 GiB) > [ 5.055049] sd 1:0:0:0: [sdb] Write Protect is off > [ 5.055093] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 > [ 5.055135] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, > doesn''t support DPO or FUA > [ 5.055870] sdb: sdb1 sdb2 sdb3 sdb4 <<6>ohci1394: fw-host0: OHCI-1394 > 1.0 (PCI): IRQ=[19] MMIO=[febff000-febff7ff] Max Packet=[2048] IR/IT > contexts=[8/8] > [ 5.089238] sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 sdb11 sdb12 sdb13 sdb14 sdb15 >> > [ 5.210775] usb 7-3: new high speed USB device using ehci_hcd and address > 2 > [ 5.225446] sd 1:0:0:0: [sdb] Attached SCSI disk > [ 5.366717] usb 7-3: configuration #1 chosen from 1 choice > [ 5.820052] usb 6-2: new low speed USB device using uhci_hcd and address > 2 > [ 5.978885] usb 6-2: configuration #1 chosen from 1 choice > [ 5.997653] usbcore: registered new interface driver hiddev > [ 6.011010] input: HID 062a:0001 as > /devices/pci0000:00/0000:00:1d.2/usb6/6-2/6-2:1.0/input/input2 > [ 6.060151] generic-usb 0003:062A:0001.0001: input,hidraw0: USB HID v1.10 > Mouse [HID 062a:0001] on usb-0000:00:1d.2-2/input0 > [ 6.060227] usbcore: registered new interface driver usbhid > [ 6.060273] usbhid: v2.6:USB HID core driver > [ 6.400260] ieee1394: Host added: ID:BUS[0-00:1023] > GUID[001e8c00000473b7] > [ 6.851294] kjournald starting. Commit interval 5 seconds > [ 6.851362] EXT3-fs: mounted filesystem with ordered data mode. > [ 10.765443] udevd version 124 started > [ 11.208483] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > [ 11.275883] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 > [ 11.381050] input: Power Button (FF) as > /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 > [ 11.420109] ACPI: Power Button (FF) [PWRF] > [ 11.420268] input: Power Button (CM) as > /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4 > [ 11.470057] ACPI: Power Button (CM) [PWRB] > [ 11.620858] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled > [ 11.621039] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > [ 11.775043] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > [ 11.995737] iTCO_vendor_support: vendor-support=0 > [ 12.060129] cfg80211: Using static regulatory domain info > [ 12.060178] cfg80211: Regulatory domain: US > [ 12.060221] (start_freq - end_freq @ bandwidth), (max_antenna_gain, > max_eirp) > [ 12.060278] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 > mBm) > [ 12.060330] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 > mBm) > [ 12.060379] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 > mBm) > [ 12.060426] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 > mBm) > [ 12.060472] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 > mBm) > [ 12.060519] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 > mBm) > [ 12.060566] cfg80211: Calling CRDA for country: US > [ 12.093247] input: PC Speaker as /devices/platform/pcspkr/input/input5 > [ 12.245134] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.04 > [ 12.245331] iTCO_wdt: Found a ICH9R TCO device (Version=2, > TCOBASE=0x0860) > [ 12.245470] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) > [ 15.046681] wmaster0 (rtl8187): not using net_device_ops yet > [ 15.047140] phy0: Selected rate control algorithm ''minstrel'' > [ 15.706225] xen: registering gsi 22 triggering 0 polarity 1 > [ 15.706229] xen_allocate_pirq: returning irq 22 for gsi 22 > [ 15.706277] xen: --> irq=22 > [ 15.706280] xen_set_ioapic_routing: irq 22 gsi 22 vector 176 ioapic 0 pin > 22 triggering 0 polarity 1 > [ 15.706341] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> > IRQ 22 > [ 15.706504] HDA Intel 0000:00:1b.0: setting latency timer to 64 > [ 15.774706] wlan0 (rtl8187): not using net_device_ops yet > [ 15.775204] phy0: hwaddr 00:15:af:51:c2:c0, RTL8187vB (default) V1 + > rtl8225z2 > [ 15.775285] usbcore: registered new interface driver rtl8187 > [ 18.674020] loop: module loaded > [ 18.865229] lp: driver loaded but no devices found > [ 19.908034] EXT3 FS on sdb1, internal journal > [ 21.061847] ip_tables: (C) 2000-2006 Netfilter Core Team > [ 21.145990] sky2 eth0: enabling interface > [ 22.371371] NET: Registered protocol family 17 > [ 24.535749] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control > both > [ 35.238274] NET: Registered protocol family 10 > [ 35.239078] lo: Disabled Privacy Extensions > [ 36.926689] warning: `avahi-daemon'' uses 32-bit capabilities (legacy > support in use) > [ 37.161134] ppdev: user-space parallel port driver > [ 38.922842] Bluetooth: Core ver 2.14 > [ 38.923043] NET: Registered protocol family 31 > [ 38.923046] Bluetooth: HCI device and connection manager initialized > [ 38.923050] Bluetooth: HCI socket layer initialized > [ 38.959459] Bluetooth: L2CAP ver 2.11 > [ 38.959462] Bluetooth: L2CAP socket layer initialized > [ 38.972740] Bluetooth: SCO (Voice Link) ver 0.6 > [ 38.972743] Bluetooth: SCO socket layer initialized > [ 39.009988] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 > [ 39.009991] Bluetooth: BNEP filters: protocol multicast > [ 39.230075] Bluetooth: RFCOMM socket layer initialized > [ 39.230085] Bluetooth: RFCOMM TTY layer initialized > [ 39.230088] Bluetooth: RFCOMM ver 1.10 > [ 43.340771] r8169: eth1: link down > [ 43.340887] ADDRCONF(NETDEV_UP): eth1: link is not ready > [ 45.520018] eth0: no IPv6 routers present > [ 45.601547] ADDRCONF(NETDEV_UP): wlan0: link is not ready > [ 45.920049] sky2 eth0: disabling interface > [ 45.967352] sky2 peth0: enabling interface > [ 45.967502] ADDRCONF(NETDEV_UP): peth0: link is not ready > [ 45.984635] device peth0 entered promiscuous mode > [ 47.890223] sky2 peth0: Link is up at 100 Mbps, full duplex, flow control > both > [ 47.890313] eth0: topology change detected, propagating > [ 47.890317] eth0: port 1(peth0) entering forwarding state > [ 47.890329] ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready > [ 56.130017] eth0: no IPv6 routers present > [ 58.560017] peth0: no IPv6 routers present > [ 61.007528] xenbus_probe wake_waiting > [ 61.007589] xenbus_probe wake_waiting > [ 61.017906] xenbus_probe_devices backend > [ 61.018050] xenbus_probe_devices failed xenbus_directory > [ 61.018095] backend_probe_and_watch devices probed ok > [ 61.018238] backend_probe_and_watch watch add ok ok > [ 61.018283] backend_probe_and_watch all done > [ 61.018327] xenbus_probe_devices device > [ 61.018463] xenbus_probe_devices failed xenbus_directory > [ 61.018509] frontend_probe_and_watch devices probed ok > [ 61.018654] frontend_probe_and_watch watch add ok ok > [ 61.018699] frontend_probe_and_watch all done > > --- On Wed, 2/18/09, Boris Derzhavets <bderzhavets@yahoo.com> wrote: > > From: Boris Derzhavets <bderzhavets@yahoo.com> > Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip > To: "Marc - A. Dahlhaus [ Administration | Westermann GmbH ]" <mad@wol.de> > Cc: "xen-devel@lists.xensource.com" <xen-devel@lists.xensource.com> > Date: Wednesday, February 18, 2009, 10:49 AM > > Mark, > I''ve just tried. Your procedure works grate. > I will try to load kernel (under Xen Unstable) after patching per Jeremy. > Thank you. > Boris. > P.S. > root@ServerXen331:~# git --version > git version 1.5.6.3 > > > --- On Tue, 2/17/09, Marc - A. Dahlhaus [ Administration | Westermann GmbH ] > <mad@wol.de> wrote: > > From: Marc - A. Dahlhaus [ Administration | Westermann GmbH ] <mad@wol.de> > Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip > To: bderzhavets@yahoo.com > Cc: "xen-devel@lists.xensource.com" <xen-devel@lists.xensource.com> > Date: Tuesday, February 17, 2009, 9:09 AM > > Hello Boris, > > > with git >= v1.5 you can get to the right branch even simpler with: > > git clone > > git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git > linux-2.6-xen > cd linux-2.6-xen > git checkout origin/xen/dom0/hackery -b xen/dom0/hackery > > To update: > git pull > > Works like a charm here but i didn''t had the time to boottest it... > > > Am Dienstag, den 17.02.2009, 05:31 -0800 schrieb Boris Derzhavets: >> Hardware config:- >> C2D E8400, 8 GB RAM, ASUS P5K Premium/WIFI (Intel P35+Intel ICH9R), >> 2x250 SATA Seagate Barracuda (no RAID). Bios settings for ICH9R - >> AHCI. >> Details here:- >> > http://bderzhavets.wordpress.com/2009/02/17/setup-xen-unstable-dom0-via-2629-rc5-pv_ops-enabled-kernel-on-intel-sataahci/ >> >> >> --- On Tue, 2/17/09, Pasi Kärkkäinen <pasik@iki.fi> wrote: >> From: Pasi Kärkkäinen <pasik@iki.fi> >> Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip >> To: "Boris Derzhavets" > > <bderzhavets@yahoo.com> >> Cc: "Ian Campbell" <Ian.Campbell@eu.citrix.com>, > "Jeremy >> Fitzhardinge" <jeremy@goop.org>, >> "xen-devel@lists.xensource.com" >> <xen-devel@lists.xensource.com> >> Date: Tuesday, February 17, 2009, 8:11 AM >> >> On Tue, Feb 17, 2009 at 03:58:45AM -0800, Boris Derzhavets wrote: >> > >> > It works fine. >> > Thank you once again >> > >> >> What kind of hardware are you running on? Which disk controller? >> >> 64-bit hypervisor/dom0 or 32-bit PAE? >> >> Would you like to send your dom0 kernel .config ? >> >> And your grub.conf .. >> >> Thanks! >> >> Nice to hear you got it > > running/working! >> >> -- Pasi >> >> _______________________________________________ >> Xen-devel mailing list >> Xen-devel@lists.xensource.com >> http://lists.xensource.com/xen-devel > > > _______________________________________________ > Xen-devel mailing list > Xen-devel@lists.xensource.com > http://lists.xensource.com/xen-devel > > > _______________________________________________ > Xen-devel mailing list > Xen-devel@lists.xensource.com > http://lists.xensource.com/xen-devel > >I built from the git tree this morning and still get the same ahci and piix problems on my test box (a dell optiplex 755), is that problem supposed to be fixed? Pretty sure I followed the correct procedure, the dom0 option was visible in menuconfig along with all the other xen options. Andy _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Andy,
Could you provide detailed specs for your CPU,Board (North,South Bridges),
HDDs
Bios vendor&version, bios settings for South Bridge.
It seems to me as hardware or bios related issue. The most recent 2.6.29-rc5
(Xen Dom0 support enabled) works fine under Xen Unstable on Intel ICH8R (ASUS
P5B Deluxe) and Intel ICH9R (ASUS P5K Premium) with bios settings AHCI for
mentioned chips. Seagate SATA II Drives 160 GB & 250 GB gets detected
properly per "dmesg" report.
Boris
I built from the git tree this morning and still get the same ahci and
piix problems on my test box (a dell optiplex 755), is that problem
supposed to be fixed?
Pretty sure I followed the correct procedure, the dom0 option was
visible in menuconfig along with all the other xen options.
Andy
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
There is a lot of snapshots down here. They have been made via remote VNC
connection
to Xen Unstable Dom0 ( 2.6.29-rc5(3) pv_ops kernel) running pretty stable on
mentioned PCs.
http://bderzhavets.wordpress.com/2009/02/17/setup-xen-unstable-dom0-via-2629-rc5-pv_ops-enabled-kernel-on-intel-sataahci/
http://bderzhavets.wordpress.com/2009/02/11/install-opensuse-111-pv-domu-via-virtual-frame-buffer-at-xen-unstable-dom0-with-2629-rc3-pv_ops-enabled-kernel-on-intel-sataahci/
http://bderzhavets.wordpress.com/2009/02/07/attempt-of-install-xen-unstable-dom0-via-2629-rc3-pv_ops-enabled-kernel-on-intel-sataahci-box/
--- On Wed, 2/18/09, Boris Derzhavets <bderzhavets@yahoo.com> wrote:
From: Boris Derzhavets <bderzhavets@yahoo.com>
Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip
To: "Andrew Lyon" <andrew.lyon@gmail.com>
Cc: "xen-devel@lists.xensource.com"
<xen-devel@lists.xensource.com>, "Marc - A. Dahlhaus [ Administration
| Westermann GmbH ]" <mad@wol.de>
Date: Wednesday, February 18, 2009, 2:16 PM
Andy,
Could you provide detailed specs for your CPU,Board (North,South Bridges),
HDDs
Bios vendor&version, bios settings for South Bridge.
It seems to me as hardware or bios related issue. The most recent 2.6.29-rc5
(Xen Dom0 support enabled) works fine under Xen Unstable on Intel ICH8R (ASUS
P5B Deluxe) and Intel ICH9R (ASUS P5K Premium) with bios settings AHCI for
mentioned chips. Seagate SATA II Drives 160 GB & 250 GB gets detected
properly per "dmesg" report.
Boris
I built from the git tree this morning and still get the same ahci and
piix problems on my test box (a dell optiplex 755), is that problem
supposed to be fixed?
Pretty sure I followed the correct procedure, the dom0 option
was
visible in menuconfig along with all the other xen options.
Andy
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
Andrew Lyon wrote:> I built from the git tree this morning and still get the same ahci and > piix problems on my test box (a dell optiplex 755), is that problem > supposed to be fixed? >Well, ahci is still a problem for me, though apparently it works fine for Boris. But PIIX should be working. Can you repost your boot logs + .config again? Also, Boris, could you post your .config? Thanks, J _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
On Tue, Feb 17, 2009 at 10:40:54AM -0800, Jeremy Fitzhardinge wrote:> Pasi Kärkkäinen wrote: > >On Tue, Feb 17, 2009 at 05:31:57AM -0800, Boris Derzhavets wrote: > > > >>Hardware config:- > >>C2D E8400, 8 GB RAM, ASUS P5K Premium/WIFI (Intel P35+Intel ICH9R), > >>2x250 SATA Seagate Barracuda (no RAID). Bios settings for ICH9R - AHCI. > >>Details here:- > >>http://bderzhavets.wordpress.com/2009/02/17/setup-xen-unstable-dom0-via-2629-rc5-pv_ops-enabled-kernel-on-intel-sataahci/ > >> > >> > > > >Thanks! > > > >So it seems you''re running 64 bit dom0 OS/hypervisor.. > > > >64 bit seems to work better atm than 32 bit.. > > > > I tend to focus on 64-bit, and Ian Campbell has been looking at 32-bit. > In theory there shouldn''t be all that much difference between them. > There have been a few issues, but they''re sharing 90+% of the code. (In > practice I''m interested in any bug reports, esp comparing 32 and 64-bit > behaviour). >I''m testing 32bit PAE dom0 on 32bit PAE hypervisor. Today, with 2.6.29-rc5, I managed to boot my dom0 into login prompt! I haven''t been able to get this working earlier.. congratulations! I had to use ''noapic'' dom0 kernel parameter though.. without ''noapic'' I''m seeing the same IRQ problems with ata_piix than earlier. My dom0 kernel config: http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.29-rc5-tip-dom0 My grub.conf: http://pasik.reaktio.net/xen/pv_ops-dom0-debug/grub.conf Working dom0 bootlog with ''noapic'': http://pasik.reaktio.net/xen/pv_ops-dom0-debug/pv_ops-dom0-bootlog-13-xen331-linux-2.6.29-rc5-noapic.txt Failing dom0 bootlog (without ''noapic''): http://pasik.reaktio.net/xen/pv_ops-dom0-debug/pv_ops-dom0-bootlog-12-xen331-linux-2.6.29-rc5.txt -- Pasi _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Pasi Kärkkäinen wrote:> On Tue, Feb 17, 2009 at 10:40:54AM -0800, Jeremy Fitzhardinge wrote: > >> Pasi Kärkkäinen wrote: >> >>> On Tue, Feb 17, 2009 at 05:31:57AM -0800, Boris Derzhavets wrote: >>> >>> >>>> Hardware config:- >>>> C2D E8400, 8 GB RAM, ASUS P5K Premium/WIFI (Intel P35+Intel ICH9R), >>>> 2x250 SATA Seagate Barracuda (no RAID). Bios settings for ICH9R - AHCI. >>>> Details here:- >>>> http://bderzhavets.wordpress.com/2009/02/17/setup-xen-unstable-dom0-via-2629-rc5-pv_ops-enabled-kernel-on-intel-sataahci/ >>>> >>>> >>>> >>> Thanks! >>> >>> So it seems you''re running 64 bit dom0 OS/hypervisor.. >>> >>> 64 bit seems to work better atm than 32 bit.. >>> >>> >> I tend to focus on 64-bit, and Ian Campbell has been looking at 32-bit. >> In theory there shouldn''t be all that much difference between them. >> There have been a few issues, but they''re sharing 90+% of the code. (In >> practice I''m interested in any bug reports, esp comparing 32 and 64-bit >> behaviour). >> >> > > I''m testing 32bit PAE dom0 on 32bit PAE hypervisor. > > Today, with 2.6.29-rc5, I managed to boot my dom0 into login prompt! > I haven''t been able to get this working earlier.. congratulations! > > I had to use ''noapic'' dom0 kernel parameter though.. without ''noapic'' I''m seeing > the same IRQ problems with ata_piix than earlier. >Hm, interesting. One change I made in the last few days was making gsis map 1:1 with irqs, like the native kernel. I wonder if that helps in your case. That said, I''m not quite sure how its working with noapic; I would have thought that it wouldn''t go through the Xen-hooked paths that way... Oh, you''re using ahci, not piix - and that works with noapic. Hm, I should try that. Can you start xend and a domain?> My dom0 kernel config: > http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.29-rc5-tip-dom0 > > My grub.conf: > http://pasik.reaktio.net/xen/pv_ops-dom0-debug/grub.conf > > Working dom0 bootlog with ''noapic'': > http://pasik.reaktio.net/xen/pv_ops-dom0-debug/pv_ops-dom0-bootlog-13-xen331-linux-2.6.29-rc5-noapic.txt >What does your /proc/interrupts look like in this case?> Failing dom0 bootlog (without ''noapic''): > http://pasik.reaktio.net/xen/pv_ops-dom0-debug/pv_ops-dom0-bootlog-12-xen331-linux-2.6.29-rc5.txt >Do you think you could boot from a usb device or something and see if you can get /proc/interrupts for this as well? Thanks, J _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Pasi Kärkkäinen wrote:> On Tue, Feb 17, 2009 at 10:40:54AM -0800, Jeremy Fitzhardinge wrote: > >> Pasi Kärkkäinen wrote: >> >>> On Tue, Feb 17, 2009 at 05:31:57AM -0800, Boris Derzhavets wrote: >>> >>> >>>> Hardware config:- >>>> C2D E8400, 8 GB RAM, ASUS P5K Premium/WIFI (Intel P35+Intel ICH9R), >>>> 2x250 SATA Seagate Barracuda (no RAID). Bios settings for ICH9R - AHCI. >>>> Details here:- >>>> http://bderzhavets.wordpress.com/2009/02/17/setup-xen-unstable-dom0-via-2629-rc5-pv_ops-enabled-kernel-on-intel-sataahci/ >>>> >>>> >>>> >>> Thanks! >>> >>> So it seems you''re running 64 bit dom0 OS/hypervisor.. >>> >>> 64 bit seems to work better atm than 32 bit.. >>> >>> >> I tend to focus on 64-bit, and Ian Campbell has been looking at 32-bit. >> In theory there shouldn''t be all that much difference between them. >> There have been a few issues, but they''re sharing 90+% of the code. (In >> practice I''m interested in any bug reports, esp comparing 32 and 64-bit >> behaviour). >> >> > > I''m testing 32bit PAE dom0 on 32bit PAE hypervisor. > > Today, with 2.6.29-rc5, I managed to boot my dom0 into login prompt! > I haven''t been able to get this working earlier.. congratulations! > > I had to use ''noapic'' dom0 kernel parameter though.. without ''noapic'' I''m seeing > the same IRQ problems with ata_piix than earlier. > > > My dom0 kernel config: > http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.29-rc5-tip-dom0 > > My grub.conf: > http://pasik.reaktio.net/xen/pv_ops-dom0-debug/grub.conf > > Working dom0 bootlog with ''noapic'': > http://pasik.reaktio.net/xen/pv_ops-dom0-debug/pv_ops-dom0-bootlog-13-xen331-linux-2.6.29-rc5-noapic.txt > > Failing dom0 bootlog (without ''noapic''): > http://pasik.reaktio.net/xen/pv_ops-dom0-debug/pv_ops-dom0-bootlog-12-xen331-linux-2.6.29-rc5.txt >I wonder if this is part of the problem: ACPI: PM-Timer IO Port: 0x408 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) IOAPIC[0]: Unable to change apic_id! ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ IOAPIC[0]: apic_id 255, version 32, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x05] address[0xfec84400] gsi_base[24]) IOAPIC[1]: apic_id 5, version 32, address 0xfec84400, GSI 24-47 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) Enabling APIC mode: Flat. Using 2 I/O APICs Using ACPI (MADT) for SMP configuration information Not really sure what this is about. Keir? Jan? Is this significant? One of my test machines show this here: ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x03] address[0xfec80000] gsi_base[32]) IOAPIC[1]: apic_id 3, version 0, address 0xfec80000, GSI 32-55 ACPI: IOAPIC (id[0x04] address[0xfec83000] gsi_base[64]) IOAPIC[2]: apic_id 4, version 0, address 0xfec83000, GSI 64-87 (It doesn''t have ahci, unfortunately, so it doesn''t tell us much about that.) J _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Yes, # # Automatically generated make config: don''t edit # Linux kernel version: 2.6.29-rc5 # Wed Feb 18 10:43:59 2009 # CONFIG_64BIT=y # CONFIG_X86_32 is not set CONFIG_X86_64=y CONFIG_X86=y CONFIG_ARCH_DEFCONFIG="arch/x86/configs/x86_64_defconfig" CONFIG_GENERIC_TIME=y CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_CLOCKSOURCE_WATCHDOG=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y CONFIG_FAST_CMPXCHG_LOCAL=y CONFIG_MMU=y CONFIG_ZONE_DMA=y CONFIG_GENERIC_ISA_DMA=y CONFIG_GENERIC_IOMAP=y CONFIG_GENERIC_BUG=y CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_GPIO=y CONFIG_ARCH_MAY_HAVE_PC_FDC=y CONFIG_RWSEM_GENERIC_SPINLOCK=y # CONFIG_RWSEM_XCHGADD_ALGORITHM is not set CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_ARCH_HAS_CPU_RELAX=y CONFIG_ARCH_HAS_DEFAULT_IDLE=y CONFIG_ARCH_HAS_CACHE_LINE_SIZE=y CONFIG_HAVE_SETUP_PER_CPU_AREA=y CONFIG_HAVE_CPUMASK_OF_CPU_MAP=y CONFIG_ARCH_HIBERNATION_POSSIBLE=y CONFIG_ARCH_SUSPEND_POSSIBLE=y CONFIG_ZONE_DMA32=y CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_AUDIT_ARCH=y CONFIG_ARCH_SUPPORTS_OPTIMIZED_INLINING=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_GENERIC_PENDING_IRQ=y CONFIG_USE_GENERIC_SMP_HELPERS=y CONFIG_X86_64_SMP=y CONFIG_X86_HT=y CONFIG_X86_TRAMPOLINE=y # CONFIG_KTIME_SCALAR is not set CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" # # General setup # CONFIG_EXPERIMENTAL=y CONFIG_LOCK_KERNEL=y CONFIG_INIT_ENV_ARG_LIMIT=32 CONFIG_LOCALVERSION="" # CONFIG_LOCALVERSION_AUTO is not set CONFIG_SWAP=y CONFIG_SYSVIPC=y CONFIG_SYSVIPC_SYSCTL=y CONFIG_POSIX_MQUEUE=y CONFIG_BSD_PROCESS_ACCT=y CONFIG_BSD_PROCESS_ACCT_V3=y CONFIG_TASKSTATS=y # CONFIG_TASK_DELAY_ACCT is not set CONFIG_TASK_XACCT=y CONFIG_TASK_IO_ACCOUNTING=y CONFIG_AUDIT=y CONFIG_AUDITSYSCALL=y CONFIG_AUDIT_TREE=y # # RCU Subsystem # CONFIG_CLASSIC_RCU=y # CONFIG_TREE_RCU is not set # CONFIG_PREEMPT_RCU is not set # CONFIG_TREE_RCU_TRACE is not set # CONFIG_PREEMPT_RCU_TRACE is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=17 CONFIG_HAVE_UNSTABLE_SCHED_CLOCK=y CONFIG_GROUP_SCHED=y CONFIG_FAIR_GROUP_SCHED=y CONFIG_RT_GROUP_SCHED=y # CONFIG_USER_SCHED is not set CONFIG_CGROUP_SCHED=y CONFIG_CGROUPS=y # CONFIG_CGROUP_DEBUG is not set CONFIG_CGROUP_NS=y # CONFIG_CGROUP_FREEZER is not set # CONFIG_CGROUP_DEVICE is not set CONFIG_CPUSETS=y CONFIG_PROC_PID_CPUSET=y CONFIG_CGROUP_CPUACCT=y CONFIG_RESOURCE_COUNTERS=y CONFIG_CGROUP_MEM_RES_CTLR=y # CONFIG_CGROUP_MEM_RES_CTLR_SWAP is not set CONFIG_MM_OWNER=y # CONFIG_SYSFS_DEPRECATED_V2 is not set CONFIG_RELAY=y CONFIG_NAMESPACES=y CONFIG_UTS_NS=y CONFIG_IPC_NS=y # CONFIG_USER_NS is not set # CONFIG_PID_NS is not set # CONFIG_NET_NS is not set CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_SYSCTL=y # CONFIG_EMBEDDED is not set CONFIG_UID16=y CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y # CONFIG_KALLSYMS_EXTRA_PASS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y CONFIG_PCSPKR_PLATFORM=y # CONFIG_COMPAT_BRK is not set CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y CONFIG_HAVE_PERF_COUNTERS=y # # Performance Counters # CONFIG_PERF_COUNTERS=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set CONFIG_PROFILING=y CONFIG_TRACEPOINTS=y CONFIG_MARKERS=y CONFIG_OPROFILE=m # CONFIG_OPROFILE_IBS is not set CONFIG_HAVE_OPROFILE=y CONFIG_KPROBES=y CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y CONFIG_KRETPROBES=y CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 CONFIG_MODULES=y # CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y # CONFIG_BLK_DEV_BSG is not set CONFIG_BLK_DEV_INTEGRITY=y CONFIG_BLOCK_COMPAT=y # # IO Schedulers # CONFIG_IOSCHED_NOOP=y CONFIG_IOSCHED_AS=y CONFIG_IOSCHED_DEADLINE=y CONFIG_IOSCHED_CFQ=y # CONFIG_DEFAULT_AS is not set CONFIG_DEFAULT_DEADLINE=y # CONFIG_DEFAULT_CFQ is not set # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="deadline" CONFIG_FREEZER=y # # Processor type and features # # CONFIG_NO_HZ is not set # CONFIG_HIGH_RES_TIMERS is not set CONFIG_GENERIC_CLOCKEVENTS_BUILD=y CONFIG_SMP=y # CONFIG_X86_X2APIC is not set # CONFIG_SPARSE_IRQ is not set CONFIG_X86_MPPARSE=y CONFIG_X86_EXTENDED_PLATFORM=y # CONFIG_X86_VSMP is not set # CONFIG_X86_UV is not set CONFIG_SCHED_OMIT_FRAME_POINTER=y CONFIG_PARAVIRT_GUEST=y CONFIG_XEN=y CONFIG_XEN_MAX_DOMAIN_MEMORY=32 CONFIG_XEN_SAVE_RESTORE=y CONFIG_XEN_DEBUG_FS=y CONFIG_XEN_DOM0=y CONFIG_XEN_PRIVILEGED_GUEST=y CONFIG_XEN_DOM0_PCI=y # CONFIG_KVM_CLOCK is not set # CONFIG_KVM_GUEST is not set CONFIG_PARAVIRT=y CONFIG_PARAVIRT_CLOCK=y # CONFIG_PARAVIRT_DEBUG is not set # CONFIG_MEMTEST is not set # CONFIG_M386 is not set # CONFIG_M486 is not set # CONFIG_M586 is not set # CONFIG_M586TSC is not set # CONFIG_M586MMX is not set # CONFIG_M686 is not set # CONFIG_MPENTIUMII is not set # CONFIG_MPENTIUMIII is not set # CONFIG_MPENTIUMM is not set # CONFIG_MPENTIUM4 is not set # CONFIG_MK6 is not set # CONFIG_MK7 is not set # CONFIG_MK8 is not set # CONFIG_MCRUSOE is not set # CONFIG_MEFFICEON is not set # CONFIG_MWINCHIPC6 is not set # CONFIG_MWINCHIP3D is not set # CONFIG_MGEODEGX1 is not set # CONFIG_MGEODE_LX is not set # CONFIG_MCYRIXIII is not set # CONFIG_MVIAC3_2 is not set # CONFIG_MVIAC7 is not set # CONFIG_MPSC is not set # CONFIG_MCORE2 is not set CONFIG_GENERIC_CPU=y CONFIG_X86_CPU=y CONFIG_X86_L1_CACHE_BYTES=64 CONFIG_X86_INTERNODE_CACHE_BYTES=64 CONFIG_X86_CMPXCHG=y CONFIG_X86_L1_CACHE_SHIFT=6 CONFIG_X86_WP_WORKS_OK=y CONFIG_X86_TSC=y CONFIG_X86_CMPXCHG64=y CONFIG_X86_CMOV=y CONFIG_X86_MINIMUM_CPU_FAMILY=64 CONFIG_X86_DEBUGCTLMSR=y CONFIG_CPU_SUP_INTEL=y CONFIG_CPU_SUP_AMD=y CONFIG_CPU_SUP_CENTAUR_64=y CONFIG_X86_DS=y CONFIG_X86_PTRACE_BTS=y CONFIG_HPET_TIMER=y CONFIG_HPET_EMULATE_RTC=y CONFIG_DMI=y CONFIG_GART_IOMMU=y # CONFIG_CALGARY_IOMMU is not set # CONFIG_AMD_IOMMU is not set CONFIG_SWIOTLB=y CONFIG_IOMMU_HELPER=y # CONFIG_IOMMU_API is not set # CONFIG_MAXSMP is not set CONFIG_NR_CPUS=32 # CONFIG_SCHED_SMT is not set CONFIG_SCHED_MC=y CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set CONFIG_X86_LOCAL_APIC=y CONFIG_X86_IO_APIC=y # CONFIG_X86_REROUTE_FOR_BROKEN_BOOT_IRQS is not set # CONFIG_X86_MCE is not set CONFIG_I8K=m CONFIG_MICROCODE=m CONFIG_MICROCODE_INTEL=y # CONFIG_MICROCODE_AMD is not set CONFIG_MICROCODE_OLD_INTERFACE=y CONFIG_X86_MSR=m CONFIG_X86_CPUID=m CONFIG_ARCH_PHYS_ADDR_T_64BIT=y CONFIG_DIRECT_GBPAGES=y # CONFIG_NUMA is not set CONFIG_ARCH_SPARSEMEM_DEFAULT=y CONFIG_ARCH_SPARSEMEM_ENABLE=y CONFIG_ARCH_SELECT_MEMORY_MODEL=y CONFIG_ILLEGAL_POINTER_VALUE=0xdead000000000000 CONFIG_SELECT_MEMORY_MODEL=y # CONFIG_FLATMEM_MANUAL is not set # CONFIG_DISCONTIGMEM_MANUAL is not set CONFIG_SPARSEMEM_MANUAL=y CONFIG_SPARSEMEM=y CONFIG_HAVE_MEMORY_PRESENT=y CONFIG_SPARSEMEM_EXTREME=y CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y CONFIG_SPARSEMEM_VMEMMAP=y # CONFIG_MEMORY_HOTPLUG is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_PHYS_ADDR_T_64BIT=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y CONFIG_UNEVICTABLE_LRU=y # CONFIG_X86_CHECK_BIOS_CORRUPTION is not set CONFIG_X86_RESERVE_LOW_64K=y CONFIG_MTRR=y CONFIG_MTRR_SANITIZER=y CONFIG_MTRR_SANITIZER_ENABLE_DEFAULT=0 CONFIG_MTRR_SANITIZER_SPARE_REG_NR_DEFAULT=1 # CONFIG_X86_PAT is not set # CONFIG_EFI is not set CONFIG_SECCOMP=y # CONFIG_CC_STACKPROTECTOR is not set CONFIG_HZ_100=y # CONFIG_HZ_250 is not set # CONFIG_HZ_300 is not set # CONFIG_HZ_1000 is not set CONFIG_HZ=100 # CONFIG_SCHED_HRTICK is not set # CONFIG_KEXEC is not set # CONFIG_CRASH_DUMP is not set CONFIG_PHYSICAL_START=0x200000 # CONFIG_RELOCATABLE is not set CONFIG_PHYSICAL_ALIGN=0x200000 CONFIG_HOTPLUG_CPU=y # CONFIG_COMPAT_VDSO is not set # CONFIG_CMDLINE_BOOL is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y # # Power management and ACPI options # CONFIG_PM=y CONFIG_PM_DEBUG=y # CONFIG_PM_VERBOSE is not set CONFIG_CAN_PM_TRACE=y CONFIG_PM_TRACE=y CONFIG_PM_TRACE_RTC=y CONFIG_PM_SLEEP_SMP=y CONFIG_PM_SLEEP=y CONFIG_SUSPEND=y CONFIG_PM_TEST_SUSPEND=y CONFIG_SUSPEND_FREEZER=y # CONFIG_HIBERNATION is not set CONFIG_ACPI=y CONFIG_ACPI_SLEEP=y CONFIG_ACPI_PROCFS=y CONFIG_ACPI_PROCFS_POWER=y CONFIG_ACPI_SYSFS_POWER=y CONFIG_ACPI_PROC_EVENT=y CONFIG_ACPI_AC=m CONFIG_ACPI_BATTERY=m CONFIG_ACPI_BUTTON=m CONFIG_ACPI_VIDEO=m CONFIG_ACPI_FAN=m CONFIG_ACPI_DOCK=y CONFIG_ACPI_PROCESSOR=m CONFIG_ACPI_HOTPLUG_CPU=y CONFIG_ACPI_THERMAL=m CONFIG_ACPI_CUSTOM_DSDT_FILE="" # CONFIG_ACPI_CUSTOM_DSDT is not set CONFIG_ACPI_BLACKLIST_YEAR=0 # CONFIG_ACPI_DEBUG is not set CONFIG_ACPI_PCI_SLOT=m CONFIG_ACPI_SYSTEM=y CONFIG_X86_PM_TIMER=y CONFIG_ACPI_CONTAINER=m CONFIG_ACPI_SBS=m # # CPU Frequency scaling # # CONFIG_CPU_FREQ is not set CONFIG_CPU_IDLE=y CONFIG_CPU_IDLE_GOV_LADDER=y # # Memory power savings # # CONFIG_I7300_IDLE is not set # # Bus options (PCI etc.) # CONFIG_PCI=y CONFIG_PCI_DIRECT=y CONFIG_PCI_MMCONFIG=y CONFIG_PCI_XEN=y CONFIG_PCI_DOMAINS=y # CONFIG_DMAR is not set # CONFIG_INTR_REMAP is not set CONFIG_PCIEPORTBUS=y CONFIG_HOTPLUG_PCI_PCIE=m CONFIG_PCIEAER=y # CONFIG_PCIEASPM is not set CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_PCI_MSI=y CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set # CONFIG_PCI_STUB is not set CONFIG_HT_IRQ=y CONFIG_ISA_DMA_API=y CONFIG_K8_NB=y CONFIG_PCCARD=m # CONFIG_PCMCIA_DEBUG is not set CONFIG_PCMCIA=m CONFIG_PCMCIA_LOAD_CIS=y CONFIG_PCMCIA_IOCTL=y CONFIG_CARDBUS=y # # PC-card bridges # CONFIG_YENTA=m CONFIG_YENTA_O2=y CONFIG_YENTA_RICOH=y CONFIG_YENTA_TI=y CONFIG_YENTA_ENE_TUNE=y CONFIG_YENTA_TOSHIBA=y CONFIG_PD6729=m CONFIG_I82092=m CONFIG_PCCARD_NONSTATIC=m CONFIG_HOTPLUG_PCI=m CONFIG_HOTPLUG_PCI_FAKE=m CONFIG_HOTPLUG_PCI_ACPI=m CONFIG_HOTPLUG_PCI_ACPI_IBM=m CONFIG_HOTPLUG_PCI_CPCI=y CONFIG_HOTPLUG_PCI_CPCI_ZT5550=m CONFIG_HOTPLUG_PCI_CPCI_GENERIC=m CONFIG_HOTPLUG_PCI_SHPC=m # # Executable file formats / Emulations # CONFIG_BINFMT_ELF=y CONFIG_COMPAT_BINFMT_ELF=y # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set # CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=m CONFIG_IA32_EMULATION=y CONFIG_IA32_AOUT=m CONFIG_COMPAT=y CONFIG_COMPAT_FOR_U64_ALIGNMENT=y CONFIG_SYSVIPC_COMPAT=y CONFIG_NET=y # # Networking options # CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_PACKET=m CONFIG_PACKET_MMAP=y CONFIG_UNIX=y CONFIG_XFRM=y CONFIG_XFRM_USER=m # CONFIG_XFRM_SUB_POLICY is not set # CONFIG_XFRM_MIGRATE is not set # CONFIG_XFRM_STATISTICS is not set CONFIG_XFRM_IPCOMP=m CONFIG_NET_KEY=m # CONFIG_NET_KEY_MIGRATE is not set CONFIG_INET=y CONFIG_IP_MULTICAST=y CONFIG_IP_ADVANCED_ROUTER=y CONFIG_ASK_IP_FIB_HASH=y # CONFIG_IP_FIB_TRIE is not set CONFIG_IP_FIB_HASH=y CONFIG_IP_MULTIPLE_TABLES=y CONFIG_IP_ROUTE_MULTIPATH=y CONFIG_IP_ROUTE_VERBOSE=y # CONFIG_IP_PNP is not set CONFIG_NET_IPIP=m CONFIG_NET_IPGRE=m CONFIG_NET_IPGRE_BROADCAST=y CONFIG_IP_MROUTE=y CONFIG_IP_PIMSM_V1=y CONFIG_IP_PIMSM_V2=y # CONFIG_ARPD is not set CONFIG_SYN_COOKIES=y CONFIG_INET_AH=m CONFIG_INET_ESP=m CONFIG_INET_IPCOMP=m CONFIG_INET_XFRM_TUNNEL=m CONFIG_INET_TUNNEL=m CONFIG_INET_XFRM_MODE_TRANSPORT=m CONFIG_INET_XFRM_MODE_TUNNEL=m CONFIG_INET_XFRM_MODE_BEET=m CONFIG_INET_LRO=m CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y CONFIG_TCP_CONG_ADVANCED=y CONFIG_TCP_CONG_BIC=m CONFIG_TCP_CONG_CUBIC=y CONFIG_TCP_CONG_WESTWOOD=m CONFIG_TCP_CONG_HTCP=m CONFIG_TCP_CONG_HSTCP=m CONFIG_TCP_CONG_HYBLA=m CONFIG_TCP_CONG_VEGAS=m CONFIG_TCP_CONG_SCALABLE=m CONFIG_TCP_CONG_LP=m CONFIG_TCP_CONG_VENO=m CONFIG_TCP_CONG_YEAH=m CONFIG_TCP_CONG_ILLINOIS=m # CONFIG_DEFAULT_BIC is not set CONFIG_DEFAULT_CUBIC=y # CONFIG_DEFAULT_HTCP is not set # CONFIG_DEFAULT_VEGAS is not set # CONFIG_DEFAULT_WESTWOOD is not set # CONFIG_DEFAULT_RENO is not set CONFIG_DEFAULT_TCP_CONG="cubic" CONFIG_TCP_MD5SIG=y CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y # CONFIG_IPV6_ROUTER_PREF is not set # CONFIG_IPV6_OPTIMISTIC_DAD is not set CONFIG_INET6_AH=m CONFIG_INET6_ESP=m CONFIG_INET6_IPCOMP=m # CONFIG_IPV6_MIP6 is not set CONFIG_INET6_XFRM_TUNNEL=m CONFIG_INET6_TUNNEL=m CONFIG_INET6_XFRM_MODE_TRANSPORT=m CONFIG_INET6_XFRM_MODE_TUNNEL=m CONFIG_INET6_XFRM_MODE_BEET=m CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m CONFIG_IPV6_SIT=m CONFIG_IPV6_NDISC_NODETYPE=y CONFIG_IPV6_TUNNEL=m CONFIG_IPV6_MULTIPLE_TABLES=y # CONFIG_IPV6_SUBTREES is not set # CONFIG_IPV6_MROUTE is not set CONFIG_NETLABEL=y CONFIG_NETWORK_SECMARK=y CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set CONFIG_NETFILTER_ADVANCED=y CONFIG_BRIDGE_NETFILTER=y # # Core Netfilter Configuration # CONFIG_NETFILTER_NETLINK=m CONFIG_NETFILTER_NETLINK_QUEUE=m CONFIG_NETFILTER_NETLINK_LOG=m CONFIG_NF_CONNTRACK=m CONFIG_NF_CT_ACCT=y CONFIG_NF_CONNTRACK_MARK=y CONFIG_NF_CONNTRACK_SECMARK=y CONFIG_NF_CONNTRACK_EVENTS=y # CONFIG_NF_CT_PROTO_DCCP is not set CONFIG_NF_CT_PROTO_GRE=m CONFIG_NF_CT_PROTO_SCTP=m CONFIG_NF_CT_PROTO_UDPLITE=m CONFIG_NF_CONNTRACK_AMANDA=m CONFIG_NF_CONNTRACK_FTP=m CONFIG_NF_CONNTRACK_H323=m CONFIG_NF_CONNTRACK_IRC=m CONFIG_NF_CONNTRACK_NETBIOS_NS=m CONFIG_NF_CONNTRACK_PPTP=m # CONFIG_NF_CONNTRACK_SANE is not set CONFIG_NF_CONNTRACK_SIP=m CONFIG_NF_CONNTRACK_TFTP=m CONFIG_NF_CT_NETLINK=m # CONFIG_NETFILTER_TPROXY is not set CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_CONNMARK=m CONFIG_NETFILTER_XT_TARGET_CONNSECMARK=m CONFIG_NETFILTER_XT_TARGET_DSCP=m CONFIG_NETFILTER_XT_TARGET_MARK=m CONFIG_NETFILTER_XT_TARGET_NFLOG=m CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NOTRACK=m CONFIG_NETFILTER_XT_TARGET_RATEEST=m CONFIG_NETFILTER_XT_TARGET_TRACE=m CONFIG_NETFILTER_XT_TARGET_SECMARK=m CONFIG_NETFILTER_XT_TARGET_TCPMSS=m # CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP is not set CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m CONFIG_NETFILTER_XT_MATCH_CONNMARK=m CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m CONFIG_NETFILTER_XT_MATCH_DSCP=m CONFIG_NETFILTER_XT_MATCH_ESP=m CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_IPRANGE=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_OWNER=m CONFIG_NETFILTER_XT_MATCH_POLICY=m CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m CONFIG_NETFILTER_XT_MATCH_RATEEST=m CONFIG_NETFILTER_XT_MATCH_REALM=m # CONFIG_NETFILTER_XT_MATCH_RECENT is not set CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m CONFIG_IP_VS=m # CONFIG_IP_VS_IPV6 is not set # CONFIG_IP_VS_DEBUG is not set CONFIG_IP_VS_TAB_BITS=12 # # IPVS transport protocol load balancing support # CONFIG_IP_VS_PROTO_TCP=y CONFIG_IP_VS_PROTO_UDP=y CONFIG_IP_VS_PROTO_AH_ESP=y CONFIG_IP_VS_PROTO_ESP=y CONFIG_IP_VS_PROTO_AH=y # # IPVS scheduler # CONFIG_IP_VS_RR=m CONFIG_IP_VS_WRR=m CONFIG_IP_VS_LC=m CONFIG_IP_VS_WLC=m CONFIG_IP_VS_LBLC=m CONFIG_IP_VS_LBLCR=m CONFIG_IP_VS_DH=m CONFIG_IP_VS_SH=m CONFIG_IP_VS_SED=m CONFIG_IP_VS_NQ=m # # IPVS application helper # CONFIG_IP_VS_FTP=m # # IP: Netfilter Configuration # CONFIG_NF_DEFRAG_IPV4=m CONFIG_NF_CONNTRACK_IPV4=m CONFIG_NF_CONNTRACK_PROC_COMPAT=y CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_AH=m CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_TTL=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m CONFIG_IP_NF_TARGET_ULOG=m CONFIG_NF_NAT=m CONFIG_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m CONFIG_IP_NF_TARGET_NETMAP=m CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_NF_NAT_SNMP_BASIC=m CONFIG_NF_NAT_PROTO_GRE=m CONFIG_NF_NAT_PROTO_UDPLITE=m CONFIG_NF_NAT_PROTO_SCTP=m CONFIG_NF_NAT_FTP=m CONFIG_NF_NAT_IRC=m CONFIG_NF_NAT_TFTP=m CONFIG_NF_NAT_AMANDA=m CONFIG_NF_NAT_PPTP=m CONFIG_NF_NAT_H323=m CONFIG_NF_NAT_SIP=m CONFIG_IP_NF_MANGLE=m CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_SECURITY=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m CONFIG_IP_NF_ARP_MANGLE=m # # IPv6: Netfilter Configuration # CONFIG_NF_CONNTRACK_IPV6=m CONFIG_IP6_NF_QUEUE=m CONFIG_IP6_NF_IPTABLES=m CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_IP6_NF_MATCH_FRAG=m CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_HL=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m CONFIG_IP6_NF_MATCH_MH=m CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_TARGET_LOG=m CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_HL=m CONFIG_IP6_NF_RAW=m CONFIG_IP6_NF_SECURITY=m # # DECnet: Netfilter Configuration # CONFIG_DECNET_NF_GRABULATOR=m CONFIG_BRIDGE_NF_EBTABLES=m CONFIG_BRIDGE_EBT_BROUTE=m CONFIG_BRIDGE_EBT_T_FILTER=m CONFIG_BRIDGE_EBT_T_NAT=m CONFIG_BRIDGE_EBT_802_3=m CONFIG_BRIDGE_EBT_AMONG=m CONFIG_BRIDGE_EBT_ARP=m CONFIG_BRIDGE_EBT_IP=m CONFIG_BRIDGE_EBT_IP6=m CONFIG_BRIDGE_EBT_LIMIT=m CONFIG_BRIDGE_EBT_MARK=m CONFIG_BRIDGE_EBT_PKTTYPE=m CONFIG_BRIDGE_EBT_STP=m CONFIG_BRIDGE_EBT_VLAN=m CONFIG_BRIDGE_EBT_ARPREPLY=m CONFIG_BRIDGE_EBT_DNAT=m CONFIG_BRIDGE_EBT_MARK_T=m CONFIG_BRIDGE_EBT_REDIRECT=m CONFIG_BRIDGE_EBT_SNAT=m CONFIG_BRIDGE_EBT_LOG=m CONFIG_BRIDGE_EBT_ULOG=m CONFIG_BRIDGE_EBT_NFLOG=m CONFIG_IP_DCCP=m CONFIG_INET_DCCP_DIAG=m # # DCCP CCIDs Configuration (EXPERIMENTAL) # # CONFIG_IP_DCCP_CCID2_DEBUG is not set CONFIG_IP_DCCP_CCID3=y # CONFIG_IP_DCCP_CCID3_DEBUG is not set CONFIG_IP_DCCP_CCID3_RTO=100 CONFIG_IP_DCCP_TFRC_LIB=y # # DCCP Kernel Hacking # # CONFIG_IP_DCCP_DEBUG is not set CONFIG_NET_DCCPPROBE=m CONFIG_IP_SCTP=m # CONFIG_SCTP_DBG_MSG is not set # CONFIG_SCTP_DBG_OBJCNT is not set # CONFIG_SCTP_HMAC_NONE is not set # CONFIG_SCTP_HMAC_SHA1 is not set CONFIG_SCTP_HMAC_MD5=y CONFIG_TIPC=m # CONFIG_TIPC_ADVANCED is not set # CONFIG_TIPC_DEBUG is not set CONFIG_ATM=y CONFIG_ATM_CLIP=y # CONFIG_ATM_CLIP_NO_ICMP is not set CONFIG_ATM_LANE=m CONFIG_ATM_MPOA=m CONFIG_ATM_BR2684=m # CONFIG_ATM_BR2684_IPFILTER is not set CONFIG_STP=y CONFIG_GARP=m CONFIG_BRIDGE=y # CONFIG_NET_DSA is not set CONFIG_VLAN_8021Q=m CONFIG_VLAN_8021Q_GVRP=y CONFIG_DECNET=m # CONFIG_DECNET_ROUTER is not set CONFIG_LLC=y CONFIG_LLC2=m CONFIG_IPX=m # CONFIG_IPX_INTERN is not set CONFIG_ATALK=m CONFIG_DEV_APPLETALK=m CONFIG_IPDDP=m CONFIG_IPDDP_ENCAP=y CONFIG_IPDDP_DECAP=y CONFIG_X25=m CONFIG_LAPB=m CONFIG_ECONET=m CONFIG_ECONET_AUNUDP=y CONFIG_ECONET_NATIVE=y CONFIG_WAN_ROUTER=m CONFIG_NET_SCHED=y # # Queueing/Scheduling # CONFIG_NET_SCH_CBQ=m CONFIG_NET_SCH_HTB=m CONFIG_NET_SCH_HFSC=m CONFIG_NET_SCH_ATM=m CONFIG_NET_SCH_PRIO=m # CONFIG_NET_SCH_MULTIQ is not set CONFIG_NET_SCH_RED=m CONFIG_NET_SCH_SFQ=m CONFIG_NET_SCH_TEQL=m CONFIG_NET_SCH_TBF=m CONFIG_NET_SCH_GRED=m CONFIG_NET_SCH_DSMARK=m CONFIG_NET_SCH_NETEM=m # CONFIG_NET_SCH_DRR is not set CONFIG_NET_SCH_INGRESS=m # # Classification # CONFIG_NET_CLS=y CONFIG_NET_CLS_BASIC=m CONFIG_NET_CLS_TCINDEX=m CONFIG_NET_CLS_ROUTE4=m CONFIG_NET_CLS_ROUTE=y CONFIG_NET_CLS_FW=m CONFIG_NET_CLS_U32=m # CONFIG_CLS_U32_PERF is not set CONFIG_CLS_U32_MARK=y CONFIG_NET_CLS_RSVP=m CONFIG_NET_CLS_RSVP6=m # CONFIG_NET_CLS_FLOW is not set # CONFIG_NET_CLS_CGROUP is not set CONFIG_NET_EMATCH=y CONFIG_NET_EMATCH_STACK=32 CONFIG_NET_EMATCH_CMP=m CONFIG_NET_EMATCH_NBYTE=m CONFIG_NET_EMATCH_U32=m CONFIG_NET_EMATCH_META=m CONFIG_NET_EMATCH_TEXT=m CONFIG_NET_CLS_ACT=y CONFIG_NET_ACT_POLICE=m CONFIG_NET_ACT_GACT=m CONFIG_GACT_PROB=y CONFIG_NET_ACT_MIRRED=m CONFIG_NET_ACT_IPT=m CONFIG_NET_ACT_NAT=m CONFIG_NET_ACT_PEDIT=m CONFIG_NET_ACT_SIMP=m # CONFIG_NET_ACT_SKBEDIT is not set # CONFIG_NET_CLS_IND is not set CONFIG_NET_SCH_FIFO=y # CONFIG_DCB is not set # # Network testing # CONFIG_NET_PKTGEN=m CONFIG_NET_TCPPROBE=m CONFIG_HAMRADIO=y # # Packet Radio protocols # CONFIG_AX25=m CONFIG_AX25_DAMA_SLAVE=y CONFIG_NETROM=m CONFIG_ROSE=m # # AX.25 network device drivers # CONFIG_MKISS=m CONFIG_6PACK=m CONFIG_BPQETHER=m CONFIG_BAYCOM_SER_FDX=m CONFIG_BAYCOM_SER_HDX=m CONFIG_BAYCOM_PAR=m CONFIG_YAM=m # CONFIG_CAN is not set CONFIG_IRDA=m # # IrDA protocols # CONFIG_IRLAN=m CONFIG_IRNET=m CONFIG_IRCOMM=m CONFIG_IRDA_ULTRA=y # # IrDA options # CONFIG_IRDA_CACHE_LAST_LSAP=y CONFIG_IRDA_FAST_RR=y CONFIG_IRDA_DEBUG=y # # Infrared-port device drivers # # # SIR device drivers # CONFIG_IRTTY_SIR=m # # Dongle support # CONFIG_DONGLE=y CONFIG_ESI_DONGLE=m CONFIG_ACTISYS_DONGLE=m CONFIG_TEKRAM_DONGLE=m # CONFIG_TOIM3232_DONGLE is not set CONFIG_LITELINK_DONGLE=m CONFIG_MA600_DONGLE=m CONFIG_GIRBIL_DONGLE=m CONFIG_MCP2120_DONGLE=m CONFIG_OLD_BELKIN_DONGLE=m CONFIG_ACT200L_DONGLE=m CONFIG_KINGSUN_DONGLE=m CONFIG_KSDAZZLE_DONGLE=m CONFIG_KS959_DONGLE=m # # FIR device drivers # CONFIG_USB_IRDA=m CONFIG_SIGMATEL_FIR=m CONFIG_NSC_FIR=m CONFIG_WINBOND_FIR=m CONFIG_SMC_IRCC_FIR=m CONFIG_ALI_FIR=m CONFIG_VLSI_FIR=m CONFIG_VIA_FIR=m CONFIG_MCS_FIR=m CONFIG_BT=m CONFIG_BT_L2CAP=m CONFIG_BT_SCO=m CONFIG_BT_RFCOMM=m CONFIG_BT_RFCOMM_TTY=y CONFIG_BT_BNEP=m CONFIG_BT_BNEP_MC_FILTER=y CONFIG_BT_BNEP_PROTO_FILTER=y CONFIG_BT_CMTP=m CONFIG_BT_HIDP=m # # Bluetooth device drivers # CONFIG_BT_HCIBTUSB=m CONFIG_BT_HCIBTSDIO=m CONFIG_BT_HCIUART=m CONFIG_BT_HCIUART_H4=y CONFIG_BT_HCIUART_BCSP=y CONFIG_BT_HCIUART_LL=y CONFIG_BT_HCIBCM203X=m CONFIG_BT_HCIBPA10X=m CONFIG_BT_HCIBFUSB=m CONFIG_BT_HCIDTL1=m CONFIG_BT_HCIBT3C=m CONFIG_BT_HCIBLUECARD=m CONFIG_BT_HCIBTUART=m CONFIG_BT_HCIVHCI=m CONFIG_AF_RXRPC=m # CONFIG_AF_RXRPC_DEBUG is not set CONFIG_RXKAD=m # CONFIG_PHONET is not set CONFIG_FIB_RULES=y CONFIG_WIRELESS=y CONFIG_CFG80211=m # CONFIG_CFG80211_REG_DEBUG is not set CONFIG_NL80211=y CONFIG_WIRELESS_OLD_REGULATORY=y CONFIG_WIRELESS_EXT=y CONFIG_WIRELESS_EXT_SYSFS=y CONFIG_LIB80211=m CONFIG_LIB80211_CRYPT_WEP=m CONFIG_LIB80211_CRYPT_CCMP=m CONFIG_LIB80211_CRYPT_TKIP=m CONFIG_MAC80211=m # # Rate control algorithm selection # CONFIG_MAC80211_RC_MINSTREL=y # CONFIG_MAC80211_RC_DEFAULT_PID is not set CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y CONFIG_MAC80211_RC_DEFAULT="minstrel" CONFIG_MAC80211_MESH=y CONFIG_MAC80211_LEDS=y CONFIG_MAC80211_DEBUGFS=y # CONFIG_MAC80211_DEBUG_MENU is not set # CONFIG_WIMAX is not set CONFIG_RFKILL=m CONFIG_RFKILL_INPUT=m CONFIG_RFKILL_LEDS=y # # Device Drivers # # # Generic Driver Options # CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" # CONFIG_STANDALONE is not set CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y # CONFIG_FIRMWARE_IN_KERNEL is not set CONFIG_EXTRA_FIRMWARE="" # CONFIG_DEBUG_DRIVER is not set # CONFIG_DEBUG_DEVRES is not set # CONFIG_SYS_HYPERVISOR is not set CONFIG_CONNECTOR=y CONFIG_PROC_EVENTS=y CONFIG_MTD=m # CONFIG_MTD_DEBUG is not set CONFIG_MTD_CONCAT=m CONFIG_MTD_PARTITIONS=y # CONFIG_MTD_TESTS is not set CONFIG_MTD_REDBOOT_PARTS=m CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1 # CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set # CONFIG_MTD_REDBOOT_PARTS_READONLY is not set CONFIG_MTD_AR7_PARTS=m # # User Modules And Translation Layers # CONFIG_MTD_CHAR=m CONFIG_MTD_BLKDEVS=m CONFIG_MTD_BLOCK=m CONFIG_MTD_BLOCK_RO=m CONFIG_FTL=m CONFIG_NFTL=m CONFIG_NFTL_RW=y CONFIG_INFTL=m CONFIG_RFD_FTL=m CONFIG_SSFDC=m CONFIG_MTD_OOPS=m # # RAM/ROM/Flash chip drivers # CONFIG_MTD_CFI=m CONFIG_MTD_JEDECPROBE=m CONFIG_MTD_GEN_PROBE=m # CONFIG_MTD_CFI_ADV_OPTIONS is not set CONFIG_MTD_MAP_BANK_WIDTH_1=y CONFIG_MTD_MAP_BANK_WIDTH_2=y CONFIG_MTD_MAP_BANK_WIDTH_4=y # CONFIG_MTD_MAP_BANK_WIDTH_8 is not set # CONFIG_MTD_MAP_BANK_WIDTH_16 is not set # CONFIG_MTD_MAP_BANK_WIDTH_32 is not set CONFIG_MTD_CFI_I1=y CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I4 is not set # CONFIG_MTD_CFI_I8 is not set CONFIG_MTD_CFI_INTELEXT=m CONFIG_MTD_CFI_AMDSTD=m CONFIG_MTD_CFI_STAA=m CONFIG_MTD_CFI_UTIL=m CONFIG_MTD_RAM=m CONFIG_MTD_ROM=m CONFIG_MTD_ABSENT=m # # Mapping drivers for chip access # CONFIG_MTD_COMPLEX_MAPPINGS=y CONFIG_MTD_PHYSMAP=m # CONFIG_MTD_PHYSMAP_COMPAT is not set CONFIG_MTD_SC520CDP=m CONFIG_MTD_NETSC520=m CONFIG_MTD_TS5500=m CONFIG_MTD_SBC_GXX=m CONFIG_MTD_AMD76XROM=m CONFIG_MTD_ICHXROM=m CONFIG_MTD_ESB2ROM=m CONFIG_MTD_CK804XROM=m CONFIG_MTD_SCB2_FLASH=m CONFIG_MTD_NETtel=m CONFIG_MTD_DILNETPC=m CONFIG_MTD_DILNETPC_BOOTSIZE=0x80000 CONFIG_MTD_L440GX=m CONFIG_MTD_PCI=m CONFIG_MTD_INTEL_VR_NOR=m CONFIG_MTD_PLATRAM=m # # Self-contained MTD device drivers # CONFIG_MTD_PMC551=m # CONFIG_MTD_PMC551_BUGFIX is not set # CONFIG_MTD_PMC551_DEBUG is not set CONFIG_MTD_DATAFLASH=m # CONFIG_MTD_DATAFLASH_WRITE_VERIFY is not set # CONFIG_MTD_DATAFLASH_OTP is not set CONFIG_MTD_M25P80=m CONFIG_M25PXX_USE_FAST_READ=y CONFIG_MTD_SLRAM=m CONFIG_MTD_PHRAM=m CONFIG_MTD_MTDRAM=m CONFIG_MTDRAM_TOTAL_SIZE=4096 CONFIG_MTDRAM_ERASE_SIZE=128 CONFIG_MTD_BLOCK2MTD=m # # Disk-On-Chip Device Drivers # CONFIG_MTD_DOC2000=m CONFIG_MTD_DOC2001=m CONFIG_MTD_DOC2001PLUS=m CONFIG_MTD_DOCPROBE=m CONFIG_MTD_DOCECC=m # CONFIG_MTD_DOCPROBE_ADVANCED is not set CONFIG_MTD_DOCPROBE_ADDRESS=0 CONFIG_MTD_NAND=m # CONFIG_MTD_NAND_VERIFY_WRITE is not set # CONFIG_MTD_NAND_ECC_SMC is not set # CONFIG_MTD_NAND_MUSEUM_IDS is not set CONFIG_MTD_NAND_IDS=m CONFIG_MTD_NAND_DISKONCHIP=m # CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED is not set CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0 # CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE is not set CONFIG_MTD_NAND_CAFE=m CONFIG_MTD_NAND_NANDSIM=m CONFIG_MTD_NAND_PLATFORM=m CONFIG_MTD_ALAUDA=m CONFIG_MTD_ONENAND=m CONFIG_MTD_ONENAND_VERIFY_WRITE=y # CONFIG_MTD_ONENAND_OTP is not set CONFIG_MTD_ONENAND_2X_PROGRAM=y CONFIG_MTD_ONENAND_SIM=m # # LPDDR flash memory drivers # # CONFIG_MTD_LPDDR is not set # # UBI - Unsorted block images # CONFIG_MTD_UBI=m CONFIG_MTD_UBI_WL_THRESHOLD=4096 CONFIG_MTD_UBI_BEB_RESERVE=1 CONFIG_MTD_UBI_GLUEBI=y # # UBI debugging options # # CONFIG_MTD_UBI_DEBUG is not set CONFIG_PARPORT=m CONFIG_PARPORT_PC=m CONFIG_PARPORT_SERIAL=m CONFIG_PARPORT_PC_FIFO=y # CONFIG_PARPORT_PC_SUPERIO is not set CONFIG_PARPORT_PC_PCMCIA=m # CONFIG_PARPORT_GSC is not set CONFIG_PARPORT_AX88796=m CONFIG_PARPORT_1284=y CONFIG_PARPORT_NOT_PC=y CONFIG_PNP=y CONFIG_PNP_DEBUG_MESSAGES=y # # Protocols # CONFIG_PNPACPI=y CONFIG_BLK_DEV=y CONFIG_BLK_DEV_FD=m CONFIG_PARIDE=m # # Parallel IDE high-level drivers # CONFIG_PARIDE_PD=m CONFIG_PARIDE_PCD=m CONFIG_PARIDE_PF=m CONFIG_PARIDE_PT=m CONFIG_PARIDE_PG=m # # Parallel IDE protocol modules # CONFIG_PARIDE_ATEN=m CONFIG_PARIDE_BPCK=m CONFIG_PARIDE_COMM=m CONFIG_PARIDE_DSTR=m CONFIG_PARIDE_FIT2=m CONFIG_PARIDE_FIT3=m CONFIG_PARIDE_EPAT=m # CONFIG_PARIDE_EPATC8 is not set CONFIG_PARIDE_EPIA=m CONFIG_PARIDE_FRIQ=m CONFIG_PARIDE_FRPW=m CONFIG_PARIDE_KBIC=m CONFIG_PARIDE_KTTI=m CONFIG_PARIDE_ON20=m CONFIG_PARIDE_ON26=m CONFIG_BLK_CPQ_DA=m CONFIG_BLK_CPQ_CISS_DA=m CONFIG_CISS_SCSI_TAPE=y CONFIG_BLK_DEV_DAC960=m CONFIG_BLK_DEV_UMEM=m # CONFIG_BLK_DEV_COW_COMMON is not set CONFIG_BLK_DEV_LOOP=m CONFIG_BLK_DEV_CRYPTOLOOP=m CONFIG_BLK_DEV_NBD=m CONFIG_BLK_DEV_SX8=m CONFIG_BLK_DEV_UB=m CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=65536 # CONFIG_BLK_DEV_XIP is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set CONFIG_ATA_OVER_ETH=m CONFIG_XEN_BLKDEV_FRONTEND=y # CONFIG_BLK_DEV_HD is not set CONFIG_MISC_DEVICES=y CONFIG_IBM_ASM=m CONFIG_PHANTOM=m CONFIG_SGI_IOC4=m CONFIG_TIFM_CORE=m CONFIG_TIFM_7XX1=m # CONFIG_ICS932S401 is not set CONFIG_ENCLOSURE_SERVICES=m CONFIG_HP_ILO=m # CONFIG_C2PORT is not set # # EEPROM support # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_AT25 is not set # CONFIG_EEPROM_LEGACY is not set CONFIG_EEPROM_93CX6=m CONFIG_HAVE_IDE=y # CONFIG_IDE is not set # # SCSI device support # CONFIG_RAID_ATTRS=m CONFIG_SCSI=y CONFIG_SCSI_DMA=y CONFIG_SCSI_TGT=m CONFIG_SCSI_NETLINK=y CONFIG_SCSI_PROC_FS=y # # SCSI support type (disk, tape, CD-ROM) # CONFIG_BLK_DEV_SD=m CONFIG_CHR_DEV_ST=m CONFIG_CHR_DEV_OSST=m CONFIG_BLK_DEV_SR=m # CONFIG_BLK_DEV_SR_VENDOR is not set CONFIG_CHR_DEV_SG=m CONFIG_CHR_DEV_SCH=m CONFIG_SCSI_ENCLOSURE=m # # Some SCSI devices (e.g. CD jukebox) support multiple LUNs # CONFIG_SCSI_MULTI_LUN=y CONFIG_SCSI_CONSTANTS=y CONFIG_SCSI_LOGGING=y CONFIG_SCSI_SCAN_ASYNC=y CONFIG_SCSI_WAIT_SCAN=m # # SCSI Transports # CONFIG_SCSI_SPI_ATTRS=m CONFIG_SCSI_FC_ATTRS=m CONFIG_SCSI_FC_TGT_ATTRS=y CONFIG_SCSI_ISCSI_ATTRS=m CONFIG_SCSI_SAS_ATTRS=m CONFIG_SCSI_SAS_LIBSAS=m CONFIG_SCSI_SAS_ATA=y CONFIG_SCSI_SAS_HOST_SMP=y # CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set CONFIG_SCSI_SRP_ATTRS=m CONFIG_SCSI_SRP_TGT_ATTRS=y CONFIG_SCSI_LOWLEVEL=y CONFIG_ISCSI_TCP=m CONFIG_BLK_DEV_3W_XXXX_RAID=m CONFIG_SCSI_3W_9XXX=m CONFIG_SCSI_ACARD=m CONFIG_SCSI_AACRAID=m CONFIG_SCSI_AIC7XXX=m CONFIG_AIC7XXX_CMDS_PER_DEVICE=8 CONFIG_AIC7XXX_RESET_DELAY_MS=15000 CONFIG_AIC7XXX_DEBUG_ENABLE=y CONFIG_AIC7XXX_DEBUG_MASK=0 CONFIG_AIC7XXX_REG_PRETTY_PRINT=y # CONFIG_SCSI_AIC7XXX_OLD is not set CONFIG_SCSI_AIC79XX=m CONFIG_AIC79XX_CMDS_PER_DEVICE=32 CONFIG_AIC79XX_RESET_DELAY_MS=15000 CONFIG_AIC79XX_DEBUG_ENABLE=y CONFIG_AIC79XX_DEBUG_MASK=0 CONFIG_AIC79XX_REG_PRETTY_PRINT=y CONFIG_SCSI_AIC94XX=m # CONFIG_AIC94XX_DEBUG is not set CONFIG_SCSI_DPT_I2O=m CONFIG_SCSI_ADVANSYS=m CONFIG_SCSI_ARCMSR=m CONFIG_SCSI_ARCMSR_AER=y CONFIG_MEGARAID_NEWGEN=y CONFIG_MEGARAID_MM=m CONFIG_MEGARAID_MAILBOX=m CONFIG_MEGARAID_LEGACY=m CONFIG_MEGARAID_SAS=m CONFIG_SCSI_HPTIOP=m CONFIG_SCSI_BUSLOGIC=m # CONFIG_LIBFC is not set # CONFIG_FCOE is not set CONFIG_SCSI_DMX3191D=m CONFIG_SCSI_EATA=m CONFIG_SCSI_EATA_TAGGED_QUEUE=y CONFIG_SCSI_EATA_LINKED_COMMANDS=y CONFIG_SCSI_EATA_MAX_TAGS=16 CONFIG_SCSI_FUTURE_DOMAIN=m CONFIG_SCSI_GDTH=m CONFIG_SCSI_IPS=m CONFIG_SCSI_INITIO=m CONFIG_SCSI_INIA100=m CONFIG_SCSI_PPA=m CONFIG_SCSI_IMM=m # CONFIG_SCSI_IZIP_EPP16 is not set # CONFIG_SCSI_IZIP_SLOW_CTR is not set # CONFIG_SCSI_MVSAS is not set CONFIG_SCSI_STEX=m CONFIG_SCSI_SYM53C8XX_2=m CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1 CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16 CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64 CONFIG_SCSI_SYM53C8XX_MMIO=y CONFIG_SCSI_IPR=m # CONFIG_SCSI_IPR_TRACE is not set # CONFIG_SCSI_IPR_DUMP is not set CONFIG_SCSI_QLOGIC_1280=m CONFIG_SCSI_QLA_FC=m CONFIG_SCSI_QLA_ISCSI=m CONFIG_SCSI_LPFC=m # CONFIG_SCSI_LPFC_DEBUG_FS is not set CONFIG_SCSI_DC395x=m CONFIG_SCSI_DC390T=m CONFIG_SCSI_DEBUG=m CONFIG_SCSI_SRP=m CONFIG_SCSI_LOWLEVEL_PCMCIA=y CONFIG_PCMCIA_FDOMAIN=m CONFIG_PCMCIA_QLOGIC=m CONFIG_PCMCIA_SYM53C500=m CONFIG_SCSI_DH=m CONFIG_SCSI_DH_RDAC=m CONFIG_SCSI_DH_HP_SW=m CONFIG_SCSI_DH_EMC=m CONFIG_SCSI_DH_ALUA=m CONFIG_ATA=y # CONFIG_ATA_NONSTANDARD is not set CONFIG_ATA_ACPI=y CONFIG_SATA_PMP=y CONFIG_SATA_AHCI=y CONFIG_SATA_SIL24=m CONFIG_ATA_SFF=y CONFIG_SATA_SVW=m CONFIG_ATA_PIIX=y CONFIG_SATA_MV=m CONFIG_SATA_NV=m CONFIG_PDC_ADMA=m CONFIG_SATA_QSTOR=m CONFIG_SATA_PROMISE=m CONFIG_SATA_SX4=m CONFIG_SATA_SIL=m CONFIG_SATA_SIS=m CONFIG_SATA_ULI=m CONFIG_SATA_VIA=m CONFIG_SATA_VITESSE=m CONFIG_SATA_INIC162X=m CONFIG_PATA_ACPI=m CONFIG_PATA_ALI=m CONFIG_PATA_AMD=m CONFIG_PATA_ARTOP=m CONFIG_PATA_ATIIXP=m # CONFIG_PATA_CMD640_PCI is not set CONFIG_PATA_CMD64X=m CONFIG_PATA_CS5520=m CONFIG_PATA_CS5530=m # CONFIG_PATA_CYPRESS is not set CONFIG_PATA_EFAR=m CONFIG_ATA_GENERIC=m CONFIG_PATA_HPT366=m CONFIG_PATA_HPT37X=m # CONFIG_PATA_HPT3X2N is not set CONFIG_PATA_HPT3X3=m # CONFIG_PATA_HPT3X3_DMA is not set CONFIG_PATA_IT821X=m CONFIG_PATA_IT8213=m CONFIG_PATA_JMICRON=y CONFIG_PATA_TRIFLEX=m CONFIG_PATA_MARVELL=m CONFIG_PATA_MPIIX=m CONFIG_PATA_OLDPIIX=m CONFIG_PATA_NETCELL=m CONFIG_PATA_NINJA32=m CONFIG_PATA_NS87410=m CONFIG_PATA_NS87415=m # CONFIG_PATA_OPTI is not set # CONFIG_PATA_OPTIDMA is not set CONFIG_PATA_PCMCIA=m CONFIG_PATA_PDC_OLD=m # CONFIG_PATA_RADISYS is not set CONFIG_PATA_RZ1000=m # CONFIG_PATA_SC1200 is not set CONFIG_PATA_SERVERWORKS=m CONFIG_PATA_PDC2027X=m CONFIG_PATA_SIL680=m CONFIG_PATA_SIS=m CONFIG_PATA_VIA=m CONFIG_PATA_WINBOND=m CONFIG_PATA_SCH=m CONFIG_MD=y CONFIG_BLK_DEV_MD=m CONFIG_MD_LINEAR=m CONFIG_MD_RAID0=m CONFIG_MD_RAID1=m CONFIG_MD_RAID10=m CONFIG_MD_RAID456=m CONFIG_MD_RAID5_RESHAPE=y CONFIG_MD_MULTIPATH=m CONFIG_MD_FAULTY=m CONFIG_BLK_DEV_DM=m # CONFIG_DM_DEBUG is not set CONFIG_DM_CRYPT=m CONFIG_DM_SNAPSHOT=m CONFIG_DM_MIRROR=m CONFIG_DM_ZERO=m CONFIG_DM_MULTIPATH=m # CONFIG_DM_DELAY is not set CONFIG_DM_UEVENT=y CONFIG_FUSION=y CONFIG_FUSION_SPI=m CONFIG_FUSION_FC=m CONFIG_FUSION_SAS=m CONFIG_FUSION_MAX_SGE=128 CONFIG_FUSION_CTL=m CONFIG_FUSION_LAN=m CONFIG_FUSION_LOGGING=y # # IEEE 1394 (FireWire) support # # # Enable only one of the two stacks, unless you know what you are doing # # CONFIG_FIREWIRE is not set CONFIG_IEEE1394=m CONFIG_IEEE1394_OHCI1394=m CONFIG_IEEE1394_PCILYNX=m CONFIG_IEEE1394_SBP2=m # CONFIG_IEEE1394_SBP2_PHYS_DMA is not set CONFIG_IEEE1394_ETH1394_ROM_ENTRY=y CONFIG_IEEE1394_ETH1394=m CONFIG_IEEE1394_RAWIO=m CONFIG_IEEE1394_VIDEO1394=m CONFIG_IEEE1394_DV1394=m # CONFIG_IEEE1394_VERBOSEDEBUG is not set CONFIG_I2O=m CONFIG_I2O_LCT_NOTIFY_ON_CHANGES=y CONFIG_I2O_EXT_ADAPTEC=y CONFIG_I2O_EXT_ADAPTEC_DMA64=y CONFIG_I2O_BUS=m CONFIG_I2O_BLOCK=m CONFIG_I2O_SCSI=m CONFIG_I2O_PROC=m CONFIG_MACINTOSH_DRIVERS=y CONFIG_MAC_EMUMOUSEBTN=y CONFIG_NETDEVICES=y CONFIG_IFB=m CONFIG_DUMMY=m CONFIG_BONDING=m CONFIG_MACVLAN=m CONFIG_EQUALIZER=m CONFIG_TUN=m CONFIG_VETH=m CONFIG_NET_SB1000=m CONFIG_ARCNET=m CONFIG_ARCNET_1201=m CONFIG_ARCNET_1051=m CONFIG_ARCNET_RAW=m CONFIG_ARCNET_CAP=m CONFIG_ARCNET_COM90xx=m CONFIG_ARCNET_COM90xxIO=m CONFIG_ARCNET_RIM_I=m CONFIG_ARCNET_COM20020=m CONFIG_ARCNET_COM20020_PCI=m CONFIG_PHYLIB=m # # MII PHY device drivers # CONFIG_MARVELL_PHY=m CONFIG_DAVICOM_PHY=m CONFIG_QSEMI_PHY=m CONFIG_LXT_PHY=m CONFIG_CICADA_PHY=m CONFIG_VITESSE_PHY=m CONFIG_SMSC_PHY=m CONFIG_BROADCOM_PHY=m CONFIG_ICPLUS_PHY=m # CONFIG_REALTEK_PHY is not set # CONFIG_NATIONAL_PHY is not set # CONFIG_STE10XP is not set # CONFIG_LSI_ET1011C_PHY is not set CONFIG_MDIO_BITBANG=m # CONFIG_MDIO_GPIO is not set CONFIG_NET_ETHERNET=y CONFIG_MII=m CONFIG_HAPPYMEAL=m CONFIG_SUNGEM=m CONFIG_CASSINI=m CONFIG_NET_VENDOR_3COM=y CONFIG_VORTEX=m CONFIG_TYPHOON=m # CONFIG_ENC28J60 is not set CONFIG_NET_TULIP=y CONFIG_DE2104X=m CONFIG_TULIP=m # CONFIG_TULIP_MWI is not set # CONFIG_TULIP_MMIO is not set # CONFIG_TULIP_NAPI is not set CONFIG_DE4X5=m CONFIG_WINBOND_840=m CONFIG_DM9102=m CONFIG_ULI526X=m CONFIG_PCMCIA_XIRCOM=m CONFIG_HP100=m # CONFIG_IBM_NEW_EMAC_ZMII is not set # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set CONFIG_NET_PCI=y CONFIG_PCNET32=m CONFIG_AMD8111_ETH=m CONFIG_ADAPTEC_STARFIRE=m CONFIG_B44=m CONFIG_B44_PCI_AUTOSELECT=y CONFIG_B44_PCICORE_AUTOSELECT=y CONFIG_B44_PCI=y CONFIG_FORCEDETH=m # CONFIG_FORCEDETH_NAPI is not set CONFIG_E100=m CONFIG_FEALNX=m CONFIG_NATSEMI=m CONFIG_NE2K_PCI=m CONFIG_8139CP=m CONFIG_8139TOO=m CONFIG_8139TOO_PIO=y # CONFIG_8139TOO_TUNE_TWISTER is not set CONFIG_8139TOO_8129=y # CONFIG_8139_OLD_RX_RESET is not set # CONFIG_R6040 is not set CONFIG_SIS900=m CONFIG_EPIC100=m # CONFIG_SMSC9420 is not set CONFIG_SUNDANCE=m # CONFIG_SUNDANCE_MMIO is not set CONFIG_TLAN=m CONFIG_VIA_RHINE=m CONFIG_VIA_RHINE_MMIO=y CONFIG_SC92031=m CONFIG_NET_POCKET=y CONFIG_ATP=m CONFIG_DE600=m CONFIG_DE620=m CONFIG_ATL2=m CONFIG_NETDEV_1000=y CONFIG_ACENIC=m # CONFIG_ACENIC_OMIT_TIGON_I is not set # CONFIG_DL2K is not set CONFIG_E1000=m CONFIG_E1000E=m CONFIG_IP1000=m CONFIG_IGB=m # CONFIG_IGB_LRO is not set CONFIG_IGB_DCA=y CONFIG_NS83820=m CONFIG_HAMACHI=m CONFIG_YELLOWFIN=m CONFIG_R8169=m CONFIG_R8169_VLAN=y CONFIG_SIS190=m CONFIG_SKGE=m # CONFIG_SKGE_DEBUG is not set CONFIG_SKY2=m # CONFIG_SKY2_DEBUG is not set CONFIG_VIA_VELOCITY=m CONFIG_TIGON3=m CONFIG_BNX2=m CONFIG_QLA3XXX=m CONFIG_ATL1=m CONFIG_ATL1E=m # CONFIG_JME is not set # CONFIG_NETDEV_10000 is not set CONFIG_TR=y CONFIG_IBMOL=m CONFIG_3C359=m CONFIG_TMS380TR=m CONFIG_TMSPCI=m CONFIG_ABYSS=m # # Wireless LAN # CONFIG_WLAN_PRE80211=y CONFIG_STRIP=m CONFIG_PCMCIA_WAVELAN=m CONFIG_PCMCIA_NETWAVE=m CONFIG_WLAN_80211=y CONFIG_PCMCIA_RAYCS=m CONFIG_LIBERTAS=m CONFIG_LIBERTAS_USB=m CONFIG_LIBERTAS_CS=m CONFIG_LIBERTAS_SDIO=m # CONFIG_LIBERTAS_DEBUG is not set # CONFIG_LIBERTAS_THINFIRM is not set CONFIG_AIRO=m CONFIG_HERMES=m CONFIG_HERMES_CACHE_FW_ON_INIT=y CONFIG_PLX_HERMES=m CONFIG_TMD_HERMES=m CONFIG_NORTEL_HERMES=m CONFIG_PCI_HERMES=m CONFIG_PCMCIA_HERMES=m CONFIG_PCMCIA_SPECTRUM=m CONFIG_ATMEL=m CONFIG_PCI_ATMEL=m CONFIG_PCMCIA_ATMEL=m CONFIG_AIRO_CS=m CONFIG_PCMCIA_WL3501=m CONFIG_PRISM54=m CONFIG_USB_ZD1201=m CONFIG_USB_NET_RNDIS_WLAN=m CONFIG_RTL8180=m CONFIG_RTL8187=m CONFIG_ADM8211=m # CONFIG_MAC80211_HWSIM is not set CONFIG_P54_COMMON=m CONFIG_P54_USB=m CONFIG_P54_PCI=m # CONFIG_ATH5K is not set CONFIG_ATH9K=m # CONFIG_ATH9K_DEBUG is not set CONFIG_IPW2100=m CONFIG_IPW2100_MONITOR=y # CONFIG_IPW2100_DEBUG is not set CONFIG_IPW2200=m CONFIG_IPW2200_MONITOR=y CONFIG_IPW2200_RADIOTAP=y CONFIG_IPW2200_PROMISCUOUS=y CONFIG_IPW2200_QOS=y # CONFIG_IPW2200_DEBUG is not set CONFIG_LIBIPW=m # CONFIG_LIBIPW_DEBUG is not set CONFIG_IWLWIFI=m CONFIG_IWLCORE=m CONFIG_IWLWIFI_LEDS=y CONFIG_IWLWIFI_RFKILL=y # CONFIG_IWLWIFI_DEBUG is not set CONFIG_IWLAGN=m CONFIG_IWLAGN_SPECTRUM_MEASUREMENT=y CONFIG_IWLAGN_LEDS=y CONFIG_IWL4965=y CONFIG_IWL5000=y CONFIG_IWL3945=m CONFIG_IWL3945_RFKILL=y CONFIG_IWL3945_SPECTRUM_MEASUREMENT=y CONFIG_IWL3945_LEDS=y # CONFIG_IWL3945_DEBUG is not set CONFIG_HOSTAP=m CONFIG_HOSTAP_FIRMWARE=y CONFIG_HOSTAP_FIRMWARE_NVRAM=y CONFIG_HOSTAP_PLX=m CONFIG_HOSTAP_PCI=m CONFIG_HOSTAP_CS=m CONFIG_B43=m CONFIG_B43_PCI_AUTOSELECT=y CONFIG_B43_PCICORE_AUTOSELECT=y # CONFIG_B43_PCMCIA is not set CONFIG_B43_LEDS=y CONFIG_B43_RFKILL=y # CONFIG_B43_DEBUG is not set CONFIG_B43LEGACY=m CONFIG_B43LEGACY_PCI_AUTOSELECT=y CONFIG_B43LEGACY_PCICORE_AUTOSELECT=y CONFIG_B43LEGACY_LEDS=y CONFIG_B43LEGACY_RFKILL=y CONFIG_B43LEGACY_DEBUG=y CONFIG_B43LEGACY_DMA=y CONFIG_B43LEGACY_PIO=y CONFIG_B43LEGACY_DMA_AND_PIO_MODE=y # CONFIG_B43LEGACY_DMA_MODE is not set # CONFIG_B43LEGACY_PIO_MODE is not set CONFIG_ZD1211RW=m # CONFIG_ZD1211RW_DEBUG is not set # # Enable WiMAX (Networking options) to see the WiMAX drivers # # # USB Network Adapters # CONFIG_USB_CATC=m CONFIG_USB_KAWETH=m CONFIG_USB_PEGASUS=m CONFIG_USB_RTL8150=m CONFIG_USB_USBNET=m CONFIG_USB_NET_AX8817X=m CONFIG_USB_NET_CDCETHER=m CONFIG_USB_NET_DM9601=m # CONFIG_USB_NET_SMSC95XX is not set CONFIG_USB_NET_GL620A=m CONFIG_USB_NET_NET1080=m CONFIG_USB_NET_PLUSB=m CONFIG_USB_NET_MCS7830=m CONFIG_USB_NET_RNDIS_HOST=m CONFIG_USB_NET_CDC_SUBSET=m CONFIG_USB_ALI_M5632=y CONFIG_USB_AN2720=y CONFIG_USB_BELKIN=y CONFIG_USB_ARMLINUX=y CONFIG_USB_EPSON2888=y CONFIG_USB_KC2190=y CONFIG_USB_NET_ZAURUS=m CONFIG_USB_HSO=m CONFIG_NET_PCMCIA=y CONFIG_PCMCIA_3C589=m CONFIG_PCMCIA_3C574=m CONFIG_PCMCIA_FMVJ18X=m CONFIG_PCMCIA_PCNET=m CONFIG_PCMCIA_NMCLAN=m CONFIG_PCMCIA_SMC91C92=m CONFIG_PCMCIA_XIRC2PS=m CONFIG_PCMCIA_AXNET=m CONFIG_ARCNET_COM20020_CS=m # CONFIG_PCMCIA_IBMTR is not set CONFIG_WAN=y CONFIG_LANMEDIA=m CONFIG_HDLC=m CONFIG_HDLC_RAW=m CONFIG_HDLC_RAW_ETH=m CONFIG_HDLC_CISCO=m CONFIG_HDLC_FR=m CONFIG_HDLC_PPP=m CONFIG_HDLC_X25=m CONFIG_PCI200SYN=m CONFIG_WANXL=m # CONFIG_PC300TOO is not set CONFIG_FARSYNC=m CONFIG_DSCC4=m CONFIG_DSCC4_PCISYNC=y CONFIG_DSCC4_PCI_RST=y CONFIG_DLCI=m CONFIG_DLCI_MAX=8 CONFIG_WAN_ROUTER_DRIVERS=m CONFIG_CYCLADES_SYNC=m CONFIG_CYCLOMX_X25=y CONFIG_LAPBETHER=m CONFIG_X25_ASY=m CONFIG_SBNI=m # CONFIG_SBNI_MULTILINE is not set CONFIG_ATM_DRIVERS=y # CONFIG_ATM_DUMMY is not set CONFIG_ATM_TCP=m CONFIG_ATM_LANAI=m CONFIG_ATM_ENI=m # CONFIG_ATM_ENI_DEBUG is not set # CONFIG_ATM_ENI_TUNE_BURST is not set CONFIG_ATM_FIRESTREAM=m CONFIG_ATM_ZATM=m # CONFIG_ATM_ZATM_DEBUG is not set CONFIG_ATM_IDT77252=m # CONFIG_ATM_IDT77252_DEBUG is not set # CONFIG_ATM_IDT77252_RCV_ALL is not set CONFIG_ATM_IDT77252_USE_SUNI=y CONFIG_ATM_AMBASSADOR=m # CONFIG_ATM_AMBASSADOR_DEBUG is not set CONFIG_ATM_HORIZON=m # CONFIG_ATM_HORIZON_DEBUG is not set CONFIG_ATM_IA=m # CONFIG_ATM_IA_DEBUG is not set CONFIG_ATM_FORE200E=m # CONFIG_ATM_FORE200E_USE_TASKLET is not set CONFIG_ATM_FORE200E_TX_RETRY=16 CONFIG_ATM_FORE200E_DEBUG=0 CONFIG_ATM_HE=m CONFIG_ATM_HE_USE_SUNI=y # CONFIG_ATM_SOLOS is not set CONFIG_XEN_NETDEV_FRONTEND=y CONFIG_FDDI=y CONFIG_DEFXX=m # CONFIG_DEFXX_MMIO is not set CONFIG_SKFP=m CONFIG_HIPPI=y CONFIG_ROADRUNNER=m # CONFIG_ROADRUNNER_LARGE_RINGS is not set CONFIG_PLIP=m CONFIG_PPP=m CONFIG_PPP_MULTILINK=y CONFIG_PPP_FILTER=y CONFIG_PPP_ASYNC=m CONFIG_PPP_SYNC_TTY=m CONFIG_PPP_DEFLATE=m CONFIG_PPP_BSDCOMP=m CONFIG_PPP_MPPE=m CONFIG_PPPOE=m CONFIG_PPPOATM=m CONFIG_PPPOL2TP=m CONFIG_SLIP=m CONFIG_SLIP_COMPRESSED=y CONFIG_SLHC=m CONFIG_SLIP_SMART=y CONFIG_SLIP_MODE_SLIP6=y CONFIG_NET_FC=y CONFIG_NETCONSOLE=m CONFIG_NETCONSOLE_DYNAMIC=y CONFIG_NETPOLL=y # CONFIG_NETPOLL_TRAP is not set CONFIG_NET_POLL_CONTROLLER=y CONFIG_ISDN=y CONFIG_ISDN_I4L=m CONFIG_ISDN_PPP=y CONFIG_ISDN_PPP_VJ=y CONFIG_ISDN_MPP=y CONFIG_IPPP_FILTER=y CONFIG_ISDN_PPP_BSDCOMP=m CONFIG_ISDN_AUDIO=y CONFIG_ISDN_TTY_FAX=y CONFIG_ISDN_X25=y # # ISDN feature submodules # CONFIG_ISDN_DIVERSION=m # # ISDN4Linux hardware drivers # # # Passive cards # CONFIG_ISDN_DRV_HISAX=m # # D-channel protocol features # CONFIG_HISAX_EURO=y CONFIG_DE_AOC=y # CONFIG_HISAX_NO_SENDCOMPLETE is not set # CONFIG_HISAX_NO_LLC is not set # CONFIG_HISAX_NO_KEYPAD is not set CONFIG_HISAX_1TR6=y CONFIG_HISAX_NI1=y CONFIG_HISAX_MAX_CARDS=8 # # HiSax supported cards # CONFIG_HISAX_16_3=y CONFIG_HISAX_TELESPCI=y CONFIG_HISAX_S0BOX=y CONFIG_HISAX_FRITZPCI=y CONFIG_HISAX_AVM_A1_PCMCIA=y CONFIG_HISAX_ELSA=y CONFIG_HISAX_DIEHLDIVA=y CONFIG_HISAX_SEDLBAUER=y CONFIG_HISAX_NETJET=y CONFIG_HISAX_NETJET_U=y CONFIG_HISAX_NICCY=y CONFIG_HISAX_BKM_A4T=y CONFIG_HISAX_SCT_QUADRO=y CONFIG_HISAX_GAZEL=y CONFIG_HISAX_HFC_PCI=y CONFIG_HISAX_W6692=y CONFIG_HISAX_HFC_SX=y CONFIG_HISAX_ENTERNOW_PCI=y # CONFIG_HISAX_DEBUG is not set # # HiSax PCMCIA card service modules # CONFIG_HISAX_SEDLBAUER_CS=m CONFIG_HISAX_ELSA_CS=m CONFIG_HISAX_AVM_A1_CS=m CONFIG_HISAX_TELES_CS=m # # HiSax sub driver modules # CONFIG_HISAX_ST5481=m CONFIG_HISAX_HFCUSB=m CONFIG_HISAX_HFC4S8S=m CONFIG_HISAX_FRITZ_PCIPNP=m CONFIG_HISAX_HDLC=y # # Active cards # CONFIG_HYSDN=m CONFIG_HYSDN_CAPI=y CONFIG_ISDN_DRV_GIGASET=m CONFIG_GIGASET_BASE=m CONFIG_GIGASET_M105=m CONFIG_GIGASET_M101=m # CONFIG_GIGASET_DEBUG is not set # CONFIG_GIGASET_UNDOCREQ is not set CONFIG_ISDN_CAPI=m CONFIG_ISDN_DRV_AVMB1_VERBOSE_REASON=y CONFIG_CAPI_TRACE=y CONFIG_ISDN_CAPI_MIDDLEWARE=y CONFIG_ISDN_CAPI_CAPI20=m CONFIG_ISDN_CAPI_CAPIFS_BOOL=y CONFIG_ISDN_CAPI_CAPIFS=m CONFIG_ISDN_CAPI_CAPIDRV=m # # CAPI hardware drivers # CONFIG_CAPI_AVM=y CONFIG_ISDN_DRV_AVMB1_B1PCI=m CONFIG_ISDN_DRV_AVMB1_B1PCIV4=y CONFIG_ISDN_DRV_AVMB1_B1PCMCIA=m CONFIG_ISDN_DRV_AVMB1_AVM_CS=m CONFIG_ISDN_DRV_AVMB1_T1PCI=m CONFIG_ISDN_DRV_AVMB1_C4=m CONFIG_CAPI_EICON=y CONFIG_ISDN_DIVAS=m CONFIG_ISDN_DIVAS_BRIPCI=y CONFIG_ISDN_DIVAS_PRIPCI=y CONFIG_ISDN_DIVAS_DIVACAPI=m CONFIG_ISDN_DIVAS_USERIDI=m CONFIG_ISDN_DIVAS_MAINT=m CONFIG_PHONE=m # # Input device support # CONFIG_INPUT=y CONFIG_INPUT_FF_MEMLESS=m CONFIG_INPUT_POLLDEV=m # # Userland interfaces # CONFIG_INPUT_MOUSEDEV=y CONFIG_INPUT_MOUSEDEV_PSAUX=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 CONFIG_INPUT_JOYDEV=m CONFIG_INPUT_EVDEV=m CONFIG_INPUT_EVBUG=m CONFIG_XEN_KBDDEV_FRONTEND=y # # Input Device Drivers # CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y CONFIG_KEYBOARD_SUNKBD=m CONFIG_KEYBOARD_LKKBD=m CONFIG_KEYBOARD_XTKBD=m CONFIG_KEYBOARD_NEWTON=m CONFIG_KEYBOARD_STOWAWAY=m CONFIG_KEYBOARD_GPIO=m CONFIG_INPUT_MOUSE=y CONFIG_MOUSE_PS2=m CONFIG_MOUSE_PS2_ALPS=y CONFIG_MOUSE_PS2_LOGIPS2PP=y CONFIG_MOUSE_PS2_SYNAPTICS=y CONFIG_MOUSE_PS2_LIFEBOOK=y CONFIG_MOUSE_PS2_TRACKPOINT=y # CONFIG_MOUSE_PS2_ELANTECH is not set # CONFIG_MOUSE_PS2_TOUCHKIT is not set CONFIG_MOUSE_SERIAL=m CONFIG_MOUSE_APPLETOUCH=m CONFIG_MOUSE_BCM5974=m CONFIG_MOUSE_VSXXXAA=m CONFIG_MOUSE_GPIO=m CONFIG_INPUT_JOYSTICK=y CONFIG_JOYSTICK_ANALOG=m CONFIG_JOYSTICK_A3D=m CONFIG_JOYSTICK_ADI=m CONFIG_JOYSTICK_COBRA=m CONFIG_JOYSTICK_GF2K=m CONFIG_JOYSTICK_GRIP=m CONFIG_JOYSTICK_GRIP_MP=m CONFIG_JOYSTICK_GUILLEMOT=m CONFIG_JOYSTICK_INTERACT=m CONFIG_JOYSTICK_SIDEWINDER=m CONFIG_JOYSTICK_TMDC=m CONFIG_JOYSTICK_IFORCE=m CONFIG_JOYSTICK_IFORCE_USB=y CONFIG_JOYSTICK_IFORCE_232=y CONFIG_JOYSTICK_WARRIOR=m CONFIG_JOYSTICK_MAGELLAN=m CONFIG_JOYSTICK_SPACEORB=m CONFIG_JOYSTICK_SPACEBALL=m CONFIG_JOYSTICK_STINGER=m CONFIG_JOYSTICK_TWIDJOY=m CONFIG_JOYSTICK_ZHENHUA=m CONFIG_JOYSTICK_DB9=m CONFIG_JOYSTICK_GAMECON=m CONFIG_JOYSTICK_TURBOGRAFX=m CONFIG_JOYSTICK_JOYDUMP=m CONFIG_JOYSTICK_XPAD=m CONFIG_JOYSTICK_XPAD_FF=y CONFIG_JOYSTICK_XPAD_LEDS=y CONFIG_INPUT_TABLET=y CONFIG_TABLET_USB_ACECAD=m CONFIG_TABLET_USB_AIPTEK=m CONFIG_TABLET_USB_GTCO=m CONFIG_TABLET_USB_KBTAB=m CONFIG_TABLET_USB_WACOM=m CONFIG_INPUT_TOUCHSCREEN=y CONFIG_TOUCHSCREEN_ADS7846=m CONFIG_TOUCHSCREEN_FUJITSU=m CONFIG_TOUCHSCREEN_GUNZE=m CONFIG_TOUCHSCREEN_ELO=m # CONFIG_TOUCHSCREEN_WACOM_W8001 is not set CONFIG_TOUCHSCREEN_MTOUCH=m CONFIG_TOUCHSCREEN_INEXIO=m CONFIG_TOUCHSCREEN_MK712=m CONFIG_TOUCHSCREEN_PENMOUNT=m CONFIG_TOUCHSCREEN_TOUCHRIGHT=m CONFIG_TOUCHSCREEN_TOUCHWIN=m CONFIG_TOUCHSCREEN_WM97XX=m CONFIG_TOUCHSCREEN_WM9705=y CONFIG_TOUCHSCREEN_WM9712=y CONFIG_TOUCHSCREEN_WM9713=y CONFIG_TOUCHSCREEN_USB_COMPOSITE=m CONFIG_TOUCHSCREEN_USB_EGALAX=y CONFIG_TOUCHSCREEN_USB_PANJIT=y CONFIG_TOUCHSCREEN_USB_3M=y CONFIG_TOUCHSCREEN_USB_ITM=y CONFIG_TOUCHSCREEN_USB_ETURBO=y CONFIG_TOUCHSCREEN_USB_GUNZE=y CONFIG_TOUCHSCREEN_USB_DMC_TSC10=y CONFIG_TOUCHSCREEN_USB_IRTOUCH=y CONFIG_TOUCHSCREEN_USB_IDEALTEK=y CONFIG_TOUCHSCREEN_USB_GENERAL_TOUCH=y CONFIG_TOUCHSCREEN_USB_GOTOP=y CONFIG_TOUCHSCREEN_TOUCHIT213=m # CONFIG_TOUCHSCREEN_TSC2007 is not set CONFIG_INPUT_MISC=y CONFIG_INPUT_PCSPKR=m # CONFIG_INPUT_APANEL is not set CONFIG_INPUT_ATLAS_BTNS=m CONFIG_INPUT_ATI_REMOTE=m CONFIG_INPUT_ATI_REMOTE2=m CONFIG_INPUT_KEYSPAN_REMOTE=m CONFIG_INPUT_POWERMATE=m CONFIG_INPUT_YEALINK=m # CONFIG_INPUT_CM109 is not set CONFIG_INPUT_UINPUT=m # # Hardware I/O ports # CONFIG_SERIO=y CONFIG_SERIO_I8042=y CONFIG_SERIO_SERPORT=m CONFIG_SERIO_CT82C710=m CONFIG_SERIO_PARKBD=m CONFIG_SERIO_PCIPS2=m CONFIG_SERIO_LIBPS2=y CONFIG_SERIO_RAW=m CONFIG_GAMEPORT=m CONFIG_GAMEPORT_NS558=m CONFIG_GAMEPORT_L4=m CONFIG_GAMEPORT_EMU10K1=m CONFIG_GAMEPORT_FM801=m # # Character devices # CONFIG_VT=y CONFIG_CONSOLE_TRANSLATIONS=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y CONFIG_VT_HW_CONSOLE_BINDING=y CONFIG_DEVKMEM=y CONFIG_SERIAL_NONSTANDARD=y CONFIG_COMPUTONE=m CONFIG_ROCKETPORT=m CONFIG_CYCLADES=m # CONFIG_CYZ_INTR is not set CONFIG_DIGIEPCA=m CONFIG_MOXA_INTELLIO=m CONFIG_MOXA_SMARTIO=m # CONFIG_ISI is not set CONFIG_SYNCLINK=m CONFIG_SYNCLINKMP=m CONFIG_SYNCLINK_GT=m CONFIG_N_HDLC=m CONFIG_RISCOM8=m CONFIG_SPECIALIX=m CONFIG_SX=m CONFIG_RIO=m # CONFIG_RIO_OLDPCI is not set CONFIG_STALDRV=y # CONFIG_STALLION is not set # CONFIG_ISTALLION is not set CONFIG_NOZOMI=m # # Serial drivers # CONFIG_SERIAL_8250=m CONFIG_FIX_EARLYCON_MEM=y CONFIG_SERIAL_8250_PCI=m CONFIG_SERIAL_8250_PNP=m CONFIG_SERIAL_8250_CS=m CONFIG_SERIAL_8250_NR_UARTS=48 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 CONFIG_SERIAL_8250_EXTENDED=y CONFIG_SERIAL_8250_MANY_PORTS=y CONFIG_SERIAL_8250_SHARE_IRQ=y # CONFIG_SERIAL_8250_DETECT_IRQ is not set CONFIG_SERIAL_8250_RSA=y # # Non-8250 serial port support # CONFIG_SERIAL_CORE=m CONFIG_SERIAL_JSM=m CONFIG_UNIX98_PTYS=y # CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 CONFIG_PRINTER=m # CONFIG_LP_CONSOLE is not set CONFIG_PPDEV=m CONFIG_HVC_DRIVER=y CONFIG_HVC_IRQ=y CONFIG_HVC_XEN=y CONFIG_IPMI_HANDLER=m # CONFIG_IPMI_PANIC_EVENT is not set CONFIG_IPMI_DEVICE_INTERFACE=m CONFIG_IPMI_SI=m CONFIG_IPMI_WATCHDOG=m CONFIG_IPMI_POWEROFF=m CONFIG_HW_RANDOM=y CONFIG_HW_RANDOM_INTEL=m CONFIG_HW_RANDOM_AMD=m CONFIG_NVRAM=m CONFIG_R3964=m CONFIG_APPLICOM=m # # PCMCIA character devices # CONFIG_SYNCLINK_CS=m CONFIG_CARDMAN_4000=m CONFIG_CARDMAN_4040=m CONFIG_IPWIRELESS=m CONFIG_MWAVE=m CONFIG_PC8736x_GPIO=m CONFIG_NSC_GPIO=m CONFIG_RAW_DRIVER=m CONFIG_MAX_RAW_DEVS=256 # CONFIG_HPET is not set CONFIG_HANGCHECK_TIMER=m CONFIG_TCG_TPM=m CONFIG_TCG_TIS=m CONFIG_TCG_NSC=m CONFIG_TCG_ATMEL=m CONFIG_TCG_INFINEON=m CONFIG_TELCLOCK=m CONFIG_DEVPORT=y CONFIG_I2C=m CONFIG_I2C_BOARDINFO=y CONFIG_I2C_CHARDEV=m # CONFIG_I2C_HELPER_AUTO is not set # # I2C Algorithms # CONFIG_I2C_ALGOBIT=m CONFIG_I2C_ALGOPCF=m CONFIG_I2C_ALGOPCA=m # # I2C Hardware Bus support # # # PC SMBus host controller drivers # CONFIG_I2C_ALI1535=m CONFIG_I2C_ALI1563=m CONFIG_I2C_ALI15X3=m CONFIG_I2C_AMD756=m CONFIG_I2C_AMD8111=m CONFIG_I2C_I801=m CONFIG_I2C_ISCH=m CONFIG_I2C_PIIX4=m CONFIG_I2C_NFORCE2=m CONFIG_I2C_SIS5595=m CONFIG_I2C_SIS630=m CONFIG_I2C_SIS96X=m CONFIG_I2C_VIA=m CONFIG_I2C_VIAPRO=m # # I2C system bus drivers (mostly embedded / system-on-chip) # CONFIG_I2C_GPIO=m CONFIG_I2C_OCORES=m CONFIG_I2C_SIMTEC=m # # External I2C/SMBus adapter drivers # CONFIG_I2C_PARPORT=m CONFIG_I2C_PARPORT_LIGHT=m CONFIG_I2C_TAOS_EVM=m CONFIG_I2C_TINY_USB=m # # Graphics adapter I2C/DDC channel drivers # CONFIG_I2C_VOODOO3=m # # Other I2C/SMBus bus drivers # CONFIG_I2C_PCA_PLATFORM=m CONFIG_I2C_STUB=m # # Miscellaneous I2C Chip support # CONFIG_DS1682=m CONFIG_SENSORS_PCF8591=m CONFIG_SENSORS_MAX6875=m CONFIG_SENSORS_TSL2550=m # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set CONFIG_SPI=y # CONFIG_SPI_DEBUG is not set CONFIG_SPI_MASTER=y # # SPI Master Controller Drivers # CONFIG_SPI_BITBANG=m CONFIG_SPI_BUTTERFLY=m # CONFIG_SPI_GPIO is not set CONFIG_SPI_LM70_LLP=m # # SPI Protocol Masters # CONFIG_SPI_SPIDEV=m CONFIG_SPI_TLE62X0=m CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_GPIOLIB=y # CONFIG_DEBUG_GPIO is not set CONFIG_GPIO_SYSFS=y # # Memory mapped GPIO expanders: # # # I2C GPIO expanders: # CONFIG_GPIO_MAX732X=m CONFIG_GPIO_PCA953X=m CONFIG_GPIO_PCF857X=m # # PCI GPIO expanders: # # # SPI GPIO expanders: # CONFIG_GPIO_MAX7301=m CONFIG_GPIO_MCP23S08=m CONFIG_W1=m CONFIG_W1_CON=y # # 1-wire Bus Masters # CONFIG_W1_MASTER_MATROX=m CONFIG_W1_MASTER_DS2490=m CONFIG_W1_MASTER_DS2482=m CONFIG_W1_MASTER_GPIO=m # # 1-wire Slaves # CONFIG_W1_SLAVE_THERM=m CONFIG_W1_SLAVE_SMEM=m CONFIG_W1_SLAVE_DS2433=m # CONFIG_W1_SLAVE_DS2433_CRC is not set CONFIG_W1_SLAVE_DS2760=m # CONFIG_W1_SLAVE_BQ27000 is not set CONFIG_POWER_SUPPLY=y # CONFIG_POWER_SUPPLY_DEBUG is not set CONFIG_PDA_POWER=m CONFIG_BATTERY_DS2760=m # CONFIG_BATTERY_BQ27x00 is not set CONFIG_HWMON=y CONFIG_HWMON_VID=m CONFIG_SENSORS_ABITUGURU=m CONFIG_SENSORS_ABITUGURU3=m CONFIG_SENSORS_AD7414=m CONFIG_SENSORS_AD7418=m CONFIG_SENSORS_ADCXX=m CONFIG_SENSORS_ADM1021=m CONFIG_SENSORS_ADM1025=m CONFIG_SENSORS_ADM1026=m CONFIG_SENSORS_ADM1029=m CONFIG_SENSORS_ADM1031=m CONFIG_SENSORS_ADM9240=m # CONFIG_SENSORS_ADT7462 is not set CONFIG_SENSORS_ADT7470=m CONFIG_SENSORS_ADT7473=m # CONFIG_SENSORS_ADT7475 is not set CONFIG_SENSORS_K8TEMP=m CONFIG_SENSORS_ASB100=m CONFIG_SENSORS_ATXP1=m CONFIG_SENSORS_DS1621=m CONFIG_SENSORS_I5K_AMB=m CONFIG_SENSORS_F71805F=m CONFIG_SENSORS_F71882FG=m CONFIG_SENSORS_F75375S=m CONFIG_SENSORS_FSCHER=m CONFIG_SENSORS_FSCPOS=m CONFIG_SENSORS_FSCHMD=m CONFIG_SENSORS_GL518SM=m CONFIG_SENSORS_GL520SM=m CONFIG_SENSORS_CORETEMP=m CONFIG_SENSORS_IBMAEM=m CONFIG_SENSORS_IBMPEX=m CONFIG_SENSORS_IT87=m CONFIG_SENSORS_LM63=m CONFIG_SENSORS_LM70=m CONFIG_SENSORS_LM75=m CONFIG_SENSORS_LM77=m CONFIG_SENSORS_LM78=m CONFIG_SENSORS_LM80=m CONFIG_SENSORS_LM83=m CONFIG_SENSORS_LM85=m CONFIG_SENSORS_LM87=m CONFIG_SENSORS_LM90=m CONFIG_SENSORS_LM92=m CONFIG_SENSORS_LM93=m # CONFIG_SENSORS_LTC4245 is not set # CONFIG_SENSORS_MAX1111 is not set CONFIG_SENSORS_MAX1619=m CONFIG_SENSORS_MAX6650=m CONFIG_SENSORS_PC87360=m CONFIG_SENSORS_PC87427=m CONFIG_SENSORS_SIS5595=m CONFIG_SENSORS_DME1737=m CONFIG_SENSORS_SMSC47M1=m CONFIG_SENSORS_SMSC47M192=m CONFIG_SENSORS_SMSC47B397=m CONFIG_SENSORS_ADS7828=m CONFIG_SENSORS_THMC50=m CONFIG_SENSORS_VIA686A=m CONFIG_SENSORS_VT1211=m CONFIG_SENSORS_VT8231=m CONFIG_SENSORS_W83781D=m CONFIG_SENSORS_W83791D=m CONFIG_SENSORS_W83792D=m CONFIG_SENSORS_W83793=m CONFIG_SENSORS_W83L785TS=m CONFIG_SENSORS_W83L786NG=m CONFIG_SENSORS_W83627HF=m CONFIG_SENSORS_W83627EHF=m CONFIG_SENSORS_HDAPS=m # CONFIG_SENSORS_LIS3LV02D is not set CONFIG_SENSORS_APPLESMC=m # CONFIG_HWMON_DEBUG_CHIP is not set CONFIG_THERMAL=y CONFIG_THERMAL_HWMON=y CONFIG_WATCHDOG=y # CONFIG_WATCHDOG_NOWAYOUT is not set # # Watchdog Device Drivers # CONFIG_SOFT_WATCHDOG=m CONFIG_ACQUIRE_WDT=m CONFIG_ADVANTECH_WDT=m CONFIG_ALIM1535_WDT=m CONFIG_ALIM7101_WDT=m CONFIG_SC520_WDT=m CONFIG_EUROTECH_WDT=m CONFIG_IB700_WDT=m CONFIG_IBMASR=m CONFIG_WAFER_WDT=m CONFIG_I6300ESB_WDT=m CONFIG_ITCO_WDT=m CONFIG_ITCO_VENDOR_SUPPORT=y CONFIG_IT8712F_WDT=m # CONFIG_IT87_WDT is not set # CONFIG_HP_WATCHDOG is not set CONFIG_SC1200_WDT=m CONFIG_PC87413_WDT=m CONFIG_60XX_WDT=m CONFIG_SBC8360_WDT=m CONFIG_CPU5_WDT=m # CONFIG_SMSC_SCH311X_WDT is not set CONFIG_SMSC37B787_WDT=m CONFIG_W83627HF_WDT=m CONFIG_W83697HF_WDT=m # CONFIG_W83697UG_WDT is not set CONFIG_W83877F_WDT=m CONFIG_W83977F_WDT=m CONFIG_MACHZ_WDT=m CONFIG_SBC_EPX_C3_WATCHDOG=m # # PCI-based Watchdog Cards # CONFIG_PCIPCWATCHDOG=m CONFIG_WDTPCI=m CONFIG_WDT_501_PCI=y # # USB-based Watchdog Cards # CONFIG_USBPCWATCHDOG=m CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # CONFIG_SSB=m CONFIG_SSB_SPROM=y CONFIG_SSB_PCIHOST_POSSIBLE=y CONFIG_SSB_PCIHOST=y CONFIG_SSB_B43_PCI_BRIDGE=y CONFIG_SSB_PCMCIAHOST_POSSIBLE=y # CONFIG_SSB_PCMCIAHOST is not set # CONFIG_SSB_DEBUG is not set CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y CONFIG_SSB_DRIVER_PCICORE=y # # Multifunction device drivers # # CONFIG_MFD_CORE is not set CONFIG_MFD_SM501=m # CONFIG_MFD_SM501_GPIO is not set CONFIG_HTC_PASIC3=m # CONFIG_UCB1400_CORE is not set CONFIG_TPS65010=m # CONFIG_MFD_TMIO is not set # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_PCF50633 is not set # CONFIG_REGULATOR is not set # # Multimedia devices # # # Multimedia core support # CONFIG_VIDEO_DEV=m CONFIG_VIDEO_V4L2_COMMON=m CONFIG_VIDEO_ALLOW_V4L1=y CONFIG_VIDEO_V4L1_COMPAT=y CONFIG_DVB_CORE=m CONFIG_VIDEO_MEDIA=m # # Multimedia drivers # CONFIG_VIDEO_SAA7146=m CONFIG_VIDEO_SAA7146_VV=m CONFIG_MEDIA_ATTACH=y CONFIG_MEDIA_TUNER=m # CONFIG_MEDIA_TUNER_CUSTOMIZE is not set CONFIG_MEDIA_TUNER_SIMPLE=m CONFIG_MEDIA_TUNER_TDA8290=m CONFIG_MEDIA_TUNER_TDA827X=m CONFIG_MEDIA_TUNER_TDA18271=m CONFIG_MEDIA_TUNER_TDA9887=m CONFIG_MEDIA_TUNER_TEA5761=m CONFIG_MEDIA_TUNER_TEA5767=m CONFIG_MEDIA_TUNER_MT20XX=m CONFIG_MEDIA_TUNER_MT2060=m CONFIG_MEDIA_TUNER_MT2266=m CONFIG_MEDIA_TUNER_MT2131=m CONFIG_MEDIA_TUNER_QT1010=m CONFIG_MEDIA_TUNER_XC2028=m CONFIG_MEDIA_TUNER_XC5000=m CONFIG_MEDIA_TUNER_MXL5005S=m CONFIG_MEDIA_TUNER_MXL5007T=m CONFIG_VIDEO_V4L2=m CONFIG_VIDEO_V4L1=m CONFIG_VIDEOBUF_GEN=m CONFIG_VIDEOBUF_DMA_SG=m CONFIG_VIDEOBUF_VMALLOC=m CONFIG_VIDEOBUF_DVB=m CONFIG_VIDEO_BTCX=m CONFIG_VIDEO_IR=m CONFIG_VIDEO_TVEEPROM=m CONFIG_VIDEO_TUNER=m CONFIG_VIDEO_CAPTURE_DRIVERS=y # CONFIG_VIDEO_ADV_DEBUG is not set # CONFIG_VIDEO_FIXED_MINOR_RANGES is not set CONFIG_VIDEO_HELPER_CHIPS_AUTO=y CONFIG_VIDEO_IR_I2C=m CONFIG_VIDEO_TVAUDIO=m CONFIG_VIDEO_TDA7432=m CONFIG_VIDEO_TDA9840=m CONFIG_VIDEO_TDA9875=m CONFIG_VIDEO_TEA6415C=m CONFIG_VIDEO_TEA6420=m CONFIG_VIDEO_MSP3400=m CONFIG_VIDEO_CS5345=m CONFIG_VIDEO_CS53L32A=m CONFIG_VIDEO_M52790=m CONFIG_VIDEO_WM8775=m CONFIG_VIDEO_WM8739=m CONFIG_VIDEO_VP27SMPX=m CONFIG_VIDEO_BT819=m CONFIG_VIDEO_BT856=m CONFIG_VIDEO_KS0127=m CONFIG_VIDEO_OV7670=m CONFIG_VIDEO_SAA7110=m CONFIG_VIDEO_SAA7111=m CONFIG_VIDEO_SAA7114=m CONFIG_VIDEO_SAA711X=m CONFIG_VIDEO_SAA717X=m CONFIG_VIDEO_TVP5150=m CONFIG_VIDEO_VPX3220=m CONFIG_VIDEO_CX25840=m CONFIG_VIDEO_CX2341X=m CONFIG_VIDEO_SAA7127=m CONFIG_VIDEO_SAA7185=m CONFIG_VIDEO_ADV7170=m CONFIG_VIDEO_ADV7175=m CONFIG_VIDEO_UPD64031A=m CONFIG_VIDEO_UPD64083=m CONFIG_VIDEO_VIVI=m CONFIG_VIDEO_BT848=m CONFIG_VIDEO_BT848_DVB=y CONFIG_VIDEO_SAA6588=m CONFIG_VIDEO_BWQCAM=m CONFIG_VIDEO_CQCAM=m CONFIG_VIDEO_W9966=m CONFIG_VIDEO_CPIA=m CONFIG_VIDEO_CPIA_PP=m CONFIG_VIDEO_CPIA_USB=m CONFIG_VIDEO_CPIA2=m CONFIG_VIDEO_SAA5246A=m CONFIG_VIDEO_SAA5249=m CONFIG_VIDEO_STRADIS=m CONFIG_VIDEO_ZORAN=m CONFIG_VIDEO_ZORAN_DC30=m CONFIG_VIDEO_ZORAN_ZR36060=m CONFIG_VIDEO_ZORAN_BUZ=m CONFIG_VIDEO_ZORAN_DC10=m CONFIG_VIDEO_ZORAN_LML33=m CONFIG_VIDEO_ZORAN_LML33R10=m CONFIG_VIDEO_ZORAN_AVS6EYES=m CONFIG_VIDEO_MEYE=m CONFIG_VIDEO_SAA7134=m CONFIG_VIDEO_SAA7134_ALSA=m CONFIG_VIDEO_SAA7134_DVB=m CONFIG_VIDEO_MXB=m CONFIG_VIDEO_HEXIUM_ORION=m CONFIG_VIDEO_HEXIUM_GEMINI=m CONFIG_VIDEO_CX23885=m CONFIG_VIDEO_AU0828=m CONFIG_VIDEO_IVTV=m CONFIG_VIDEO_FB_IVTV=m CONFIG_VIDEO_CX18=m CONFIG_VIDEO_CAFE_CCIC=m CONFIG_SOC_CAMERA=m CONFIG_SOC_CAMERA_MT9M001=m CONFIG_MT9M001_PCA9536_SWITCH=y # CONFIG_SOC_CAMERA_MT9M111 is not set # CONFIG_SOC_CAMERA_MT9T031 is not set CONFIG_SOC_CAMERA_MT9V022=m CONFIG_MT9V022_PCA9536_SWITCH=y # CONFIG_SOC_CAMERA_TW9910 is not set CONFIG_SOC_CAMERA_PLATFORM=m # CONFIG_SOC_CAMERA_OV772X is not set CONFIG_V4L_USB_DRIVERS=y CONFIG_USB_VIDEO_CLASS=m CONFIG_USB_VIDEO_CLASS_INPUT_EVDEV=y CONFIG_USB_GSPCA=m # CONFIG_USB_M5602 is not set # CONFIG_USB_STV06XX is not set # CONFIG_USB_GSPCA_CONEX is not set # CONFIG_USB_GSPCA_ETOMS is not set # CONFIG_USB_GSPCA_FINEPIX is not set # CONFIG_USB_GSPCA_MARS is not set # CONFIG_USB_GSPCA_OV519 is not set # CONFIG_USB_GSPCA_OV534 is not set # CONFIG_USB_GSPCA_PAC207 is not set # CONFIG_USB_GSPCA_PAC7311 is not set # CONFIG_USB_GSPCA_SONIXB is not set # CONFIG_USB_GSPCA_SONIXJ is not set # CONFIG_USB_GSPCA_SPCA500 is not set # CONFIG_USB_GSPCA_SPCA501 is not set # CONFIG_USB_GSPCA_SPCA505 is not set # CONFIG_USB_GSPCA_SPCA506 is not set # CONFIG_USB_GSPCA_SPCA508 is not set # CONFIG_USB_GSPCA_SPCA561 is not set # CONFIG_USB_GSPCA_STK014 is not set # CONFIG_USB_GSPCA_SUNPLUS is not set # CONFIG_USB_GSPCA_T613 is not set # CONFIG_USB_GSPCA_TV8532 is not set # CONFIG_USB_GSPCA_VC032X is not set # CONFIG_USB_GSPCA_ZC3XX is not set CONFIG_VIDEO_PVRUSB2=m CONFIG_VIDEO_PVRUSB2_SYSFS=y CONFIG_VIDEO_PVRUSB2_DVB=y # CONFIG_VIDEO_PVRUSB2_DEBUGIFC is not set CONFIG_VIDEO_EM28XX=m CONFIG_VIDEO_EM28XX_ALSA=m CONFIG_VIDEO_EM28XX_DVB=m CONFIG_VIDEO_USBVISION=m CONFIG_VIDEO_USBVIDEO=m CONFIG_USB_VICAM=m CONFIG_USB_IBMCAM=m CONFIG_USB_KONICAWC=m CONFIG_USB_QUICKCAM_MESSENGER=m CONFIG_USB_ET61X251=m CONFIG_VIDEO_OVCAMCHIP=m CONFIG_USB_W9968CF=m # CONFIG_USB_OV511 is not set CONFIG_USB_SE401=m CONFIG_USB_SN9C102=m CONFIG_USB_STV680=m CONFIG_USB_ZC0301=m CONFIG_USB_PWC=m # CONFIG_USB_PWC_DEBUG is not set CONFIG_USB_ZR364XX=m CONFIG_USB_STKWEBCAM=m CONFIG_USB_S2255=m CONFIG_RADIO_ADAPTERS=y CONFIG_RADIO_GEMTEK_PCI=m CONFIG_RADIO_MAXIRADIO=m CONFIG_RADIO_MAESTRO=m CONFIG_USB_DSBR=m CONFIG_USB_SI470X=m # CONFIG_USB_MR800 is not set # CONFIG_RADIO_TEA5764 is not set # CONFIG_DVB_DYNAMIC_MINORS is not set CONFIG_DVB_CAPTURE_DRIVERS=y # # Supported SAA7146 based PCI Adapters # CONFIG_TTPCI_EEPROM=m CONFIG_DVB_AV7110=m # CONFIG_DVB_AV7110_FIRMWARE is not set CONFIG_DVB_AV7110_OSD=y CONFIG_DVB_BUDGET_CORE=m CONFIG_DVB_BUDGET=m CONFIG_DVB_BUDGET_CI=m CONFIG_DVB_BUDGET_AV=m CONFIG_DVB_BUDGET_PATCH=m # # Supported USB Adapters # CONFIG_DVB_USB=m # CONFIG_DVB_USB_DEBUG is not set CONFIG_DVB_USB_A800=m CONFIG_DVB_USB_DIBUSB_MB=m # CONFIG_DVB_USB_DIBUSB_MB_FAULTY is not set CONFIG_DVB_USB_DIBUSB_MC=m CONFIG_DVB_USB_DIB0700=m CONFIG_DVB_USB_UMT_010=m CONFIG_DVB_USB_CXUSB=m CONFIG_DVB_USB_M920X=m CONFIG_DVB_USB_GL861=m CONFIG_DVB_USB_AU6610=m CONFIG_DVB_USB_DIGITV=m CONFIG_DVB_USB_VP7045=m CONFIG_DVB_USB_VP702X=m CONFIG_DVB_USB_GP8PSK=m CONFIG_DVB_USB_NOVA_T_USB2=m CONFIG_DVB_USB_TTUSB2=m CONFIG_DVB_USB_DTT200U=m CONFIG_DVB_USB_OPERA1=m CONFIG_DVB_USB_DW2102=m # CONFIG_DVB_USB_CINERGY_T2 is not set CONFIG_DVB_USB_ANYSEE=m # CONFIG_DVB_USB_DTV5100 is not set # CONFIG_DVB_USB_AF9015 is not set CONFIG_DVB_TTUSB_BUDGET=m CONFIG_DVB_TTUSB_DEC=m CONFIG_DVB_SIANO_SMS1XXX=m CONFIG_DVB_SIANO_SMS1XXX_SMS_IDS=y # # Supported FlexCopII (B2C2) Adapters # CONFIG_DVB_B2C2_FLEXCOP=m CONFIG_DVB_B2C2_FLEXCOP_PCI=m CONFIG_DVB_B2C2_FLEXCOP_USB=m # CONFIG_DVB_B2C2_FLEXCOP_DEBUG is not set # # Supported BT878 Adapters # CONFIG_DVB_BT8XX=m # # Supported Pluto2 Adapters # CONFIG_DVB_PLUTO2=m # # Supported SDMC DM1105 Adapters # # CONFIG_DVB_DM1105 is not set # # Supported DVB Frontends # # # Customise DVB Frontends # # CONFIG_DVB_FE_CUSTOMISE is not set # # Multistandard (satellite) frontends # CONFIG_DVB_STB0899=m CONFIG_DVB_STB6100=m # # DVB-S (satellite) frontends # CONFIG_DVB_CX24110=m CONFIG_DVB_CX24123=m CONFIG_DVB_MT312=m CONFIG_DVB_S5H1420=m CONFIG_DVB_STV0288=m CONFIG_DVB_STB6000=m CONFIG_DVB_STV0299=m CONFIG_DVB_TDA8083=m CONFIG_DVB_TDA10086=m CONFIG_DVB_TDA8261=m CONFIG_DVB_VES1X93=m CONFIG_DVB_TUNER_ITD1000=m CONFIG_DVB_TUNER_CX24113=m CONFIG_DVB_TDA826X=m CONFIG_DVB_TUA6100=m CONFIG_DVB_CX24116=m CONFIG_DVB_SI21XX=m # # DVB-T (terrestrial) frontends # CONFIG_DVB_SP8870=m CONFIG_DVB_SP887X=m CONFIG_DVB_CX22700=m CONFIG_DVB_CX22702=m CONFIG_DVB_DRX397XD=m CONFIG_DVB_L64781=m CONFIG_DVB_TDA1004X=m CONFIG_DVB_NXT6000=m CONFIG_DVB_MT352=m CONFIG_DVB_ZL10353=m CONFIG_DVB_DIB3000MB=m CONFIG_DVB_DIB3000MC=m CONFIG_DVB_DIB7000M=m CONFIG_DVB_DIB7000P=m CONFIG_DVB_TDA10048=m # # DVB-C (cable) frontends # CONFIG_DVB_VES1820=m CONFIG_DVB_TDA10021=m CONFIG_DVB_TDA10023=m CONFIG_DVB_STV0297=m # # ATSC (North American/Korean Terrestrial/Cable DTV) frontends # CONFIG_DVB_NXT200X=m CONFIG_DVB_OR51211=m CONFIG_DVB_OR51132=m CONFIG_DVB_BCM3510=m CONFIG_DVB_LGDT330X=m # CONFIG_DVB_LGDT3304 is not set CONFIG_DVB_S5H1409=m CONFIG_DVB_AU8522=m CONFIG_DVB_S5H1411=m # # ISDB-T (terrestrial) frontends # # CONFIG_DVB_S921 is not set # # Digital terrestrial only tuners/PLL # CONFIG_DVB_PLL=m CONFIG_DVB_TUNER_DIB0070=m # # SEC control devices for DVB-S # CONFIG_DVB_LNBP21=m CONFIG_DVB_ISL6405=m CONFIG_DVB_ISL6421=m # CONFIG_DVB_LGS8GL5 is not set # # Tools to develop new frontends # # CONFIG_DVB_DUMMY_FE is not set # CONFIG_DVB_AF9013 is not set # CONFIG_DAB is not set # # Graphics support # CONFIG_AGP=y CONFIG_AGP_AMD64=y CONFIG_AGP_INTEL=m CONFIG_AGP_SIS=m CONFIG_AGP_VIA=m CONFIG_DRM=m CONFIG_DRM_TDFX=m CONFIG_DRM_R128=m CONFIG_DRM_RADEON=m CONFIG_DRM_I810=m CONFIG_DRM_I830=m CONFIG_DRM_I915=m # CONFIG_DRM_I915_KMS is not set CONFIG_DRM_MGA=m CONFIG_DRM_SIS=m CONFIG_DRM_VIA=m CONFIG_DRM_SAVAGE=m CONFIG_VGASTATE=m CONFIG_VIDEO_OUTPUT_CONTROL=m CONFIG_FB=y CONFIG_FIRMWARE_EDID=y CONFIG_FB_DDC=m CONFIG_FB_BOOT_VESA_SUPPORT=y CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set CONFIG_FB_SYS_FILLRECT=y CONFIG_FB_SYS_COPYAREA=y CONFIG_FB_SYS_IMAGEBLIT=y # CONFIG_FB_FOREIGN_ENDIAN is not set CONFIG_FB_SYS_FOPS=y CONFIG_FB_DEFERRED_IO=y CONFIG_FB_HECUBA=m CONFIG_FB_SVGALIB=m # CONFIG_FB_MACMODES is not set CONFIG_FB_BACKLIGHT=y CONFIG_FB_MODE_HELPERS=y CONFIG_FB_TILEBLITTING=y # # Frame buffer hardware drivers # CONFIG_FB_CIRRUS=m CONFIG_FB_PM2=m CONFIG_FB_PM2_FIFO_DISCONNECT=y CONFIG_FB_CYBER2000=m CONFIG_FB_ARC=m CONFIG_FB_ASILIANT=y CONFIG_FB_IMSTT=y CONFIG_FB_VGA16=m CONFIG_FB_UVESA=m # CONFIG_FB_VESA is not set CONFIG_FB_N411=m CONFIG_FB_HGA=m # CONFIG_FB_HGA_ACCEL is not set CONFIG_FB_S1D13XXX=m CONFIG_FB_NVIDIA=m CONFIG_FB_NVIDIA_I2C=y # CONFIG_FB_NVIDIA_DEBUG is not set CONFIG_FB_NVIDIA_BACKLIGHT=y CONFIG_FB_RIVA=m CONFIG_FB_RIVA_I2C=y # CONFIG_FB_RIVA_DEBUG is not set CONFIG_FB_RIVA_BACKLIGHT=y CONFIG_FB_LE80578=m CONFIG_FB_CARILLO_RANCH=m CONFIG_FB_INTEL=m # CONFIG_FB_INTEL_DEBUG is not set CONFIG_FB_INTEL_I2C=y CONFIG_FB_MATROX=m CONFIG_FB_MATROX_MILLENIUM=y CONFIG_FB_MATROX_MYSTIQUE=y CONFIG_FB_MATROX_G=y CONFIG_FB_MATROX_I2C=m CONFIG_FB_MATROX_MAVEN=m CONFIG_FB_MATROX_MULTIHEAD=y CONFIG_FB_RADEON=m CONFIG_FB_RADEON_I2C=y CONFIG_FB_RADEON_BACKLIGHT=y # CONFIG_FB_RADEON_DEBUG is not set CONFIG_FB_ATY128=m CONFIG_FB_ATY128_BACKLIGHT=y CONFIG_FB_ATY=m CONFIG_FB_ATY_CT=y CONFIG_FB_ATY_GENERIC_LCD=y CONFIG_FB_ATY_GX=y CONFIG_FB_ATY_BACKLIGHT=y CONFIG_FB_S3=m CONFIG_FB_SAVAGE=m CONFIG_FB_SAVAGE_I2C=y CONFIG_FB_SAVAGE_ACCEL=y CONFIG_FB_SIS=m CONFIG_FB_SIS_300=y CONFIG_FB_SIS_315=y # CONFIG_FB_VIA is not set CONFIG_FB_NEOMAGIC=m CONFIG_FB_KYRO=m CONFIG_FB_3DFX=m # CONFIG_FB_3DFX_ACCEL is not set CONFIG_FB_VOODOO1=m CONFIG_FB_VT8623=m CONFIG_FB_TRIDENT=m # CONFIG_FB_TRIDENT_ACCEL is not set CONFIG_FB_ARK=m CONFIG_FB_PM3=m CONFIG_FB_CARMINE=m CONFIG_FB_CARMINE_DRAM_EVAL=y # CONFIG_CARMINE_DRAM_CUSTOM is not set CONFIG_FB_GEODE=y CONFIG_FB_GEODE_LX=m CONFIG_FB_GEODE_GX=m CONFIG_FB_GEODE_GX1=m CONFIG_FB_SM501=m # CONFIG_FB_VIRTUAL is not set CONFIG_XEN_FBDEV_FRONTEND=y # CONFIG_FB_METRONOME is not set # CONFIG_FB_MB862XX is not set CONFIG_BACKLIGHT_LCD_SUPPORT=y CONFIG_LCD_CLASS_DEVICE=m CONFIG_LCD_LTV350QV=m CONFIG_LCD_ILI9320=m # CONFIG_LCD_TDO24M is not set CONFIG_LCD_VGG2432A4=m CONFIG_LCD_PLATFORM=m CONFIG_BACKLIGHT_CLASS_DEVICE=y CONFIG_BACKLIGHT_GENERIC=y CONFIG_BACKLIGHT_PROGEAR=m CONFIG_BACKLIGHT_CARILLO_RANCH=m CONFIG_BACKLIGHT_MBP_NVIDIA=m # CONFIG_BACKLIGHT_SAHARA is not set # # Display device support # CONFIG_DISPLAY_SUPPORT=m # # Display hardware drivers # # # Console display driver support # CONFIG_VGA_CONSOLE=y # CONFIG_VGACON_SOFT_SCROLLBACK is not set CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=m # CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set # CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set # CONFIG_FONTS is not set CONFIG_FONT_8x8=y CONFIG_FONT_8x16=y # CONFIG_LOGO is not set CONFIG_SOUND=m CONFIG_SOUND_OSS_CORE=y CONFIG_SND=m CONFIG_SND_TIMER=m CONFIG_SND_PCM=m CONFIG_SND_HWDEP=m CONFIG_SND_RAWMIDI=m CONFIG_SND_JACK=y CONFIG_SND_SEQUENCER=m CONFIG_SND_SEQ_DUMMY=m CONFIG_SND_OSSEMUL=y CONFIG_SND_MIXER_OSS=m CONFIG_SND_PCM_OSS=m CONFIG_SND_PCM_OSS_PLUGINS=y CONFIG_SND_SEQUENCER_OSS=y CONFIG_SND_DYNAMIC_MINORS=y CONFIG_SND_SUPPORT_OLD_API=y CONFIG_SND_VERBOSE_PROCFS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set CONFIG_SND_VMASTER=y CONFIG_SND_MPU401_UART=m CONFIG_SND_OPL3_LIB=m CONFIG_SND_VX_LIB=m CONFIG_SND_AC97_CODEC=m CONFIG_SND_DRIVERS=y CONFIG_SND_DUMMY=m CONFIG_SND_VIRMIDI=m CONFIG_SND_MTS64=m CONFIG_SND_SERIAL_U16550=m CONFIG_SND_MPU401=m CONFIG_SND_PORTMAN2X4=m CONFIG_SND_AC97_POWER_SAVE=y CONFIG_SND_AC97_POWER_SAVE_DEFAULT=0 CONFIG_SND_SB_COMMON=m CONFIG_SND_SB16_DSP=m CONFIG_SND_PCI=y CONFIG_SND_AD1889=m CONFIG_SND_ALS300=m CONFIG_SND_ALS4000=m CONFIG_SND_ALI5451=m CONFIG_SND_ATIIXP=m CONFIG_SND_ATIIXP_MODEM=m CONFIG_SND_AU8810=m CONFIG_SND_AU8820=m CONFIG_SND_AU8830=m CONFIG_SND_AW2=m CONFIG_SND_AZT3328=m CONFIG_SND_BT87X=m # CONFIG_SND_BT87X_OVERCLOCK is not set CONFIG_SND_CA0106=m CONFIG_SND_CMIPCI=m CONFIG_SND_OXYGEN_LIB=m CONFIG_SND_OXYGEN=m CONFIG_SND_CS4281=m CONFIG_SND_CS46XX=m CONFIG_SND_CS46XX_NEW_DSP=y CONFIG_SND_CS5530=m CONFIG_SND_DARLA20=m CONFIG_SND_GINA20=m CONFIG_SND_LAYLA20=m CONFIG_SND_DARLA24=m CONFIG_SND_GINA24=m CONFIG_SND_LAYLA24=m CONFIG_SND_MONA=m CONFIG_SND_MIA=m CONFIG_SND_ECHO3G=m CONFIG_SND_INDIGO=m CONFIG_SND_INDIGOIO=m CONFIG_SND_INDIGODJ=m CONFIG_SND_EMU10K1=m CONFIG_SND_EMU10K1X=m CONFIG_SND_ENS1370=m CONFIG_SND_ENS1371=m CONFIG_SND_ES1938=m CONFIG_SND_ES1968=m CONFIG_SND_FM801=m CONFIG_SND_FM801_TEA575X_BOOL=y CONFIG_SND_FM801_TEA575X=m CONFIG_SND_HDA_INTEL=m # CONFIG_SND_HDA_HWDEP is not set # CONFIG_SND_HDA_INPUT_BEEP is not set CONFIG_SND_HDA_CODEC_REALTEK=y CONFIG_SND_HDA_CODEC_ANALOG=y CONFIG_SND_HDA_CODEC_SIGMATEL=y CONFIG_SND_HDA_CODEC_VIA=y CONFIG_SND_HDA_CODEC_ATIHDMI=y CONFIG_SND_HDA_CODEC_NVHDMI=y CONFIG_SND_HDA_CODEC_INTELHDMI=y CONFIG_SND_HDA_ELD=y CONFIG_SND_HDA_CODEC_CONEXANT=y CONFIG_SND_HDA_CODEC_CMEDIA=y CONFIG_SND_HDA_CODEC_SI3054=y CONFIG_SND_HDA_GENERIC=y CONFIG_SND_HDA_POWER_SAVE=y CONFIG_SND_HDA_POWER_SAVE_DEFAULT=0 CONFIG_SND_HDSP=m CONFIG_SND_HDSPM=m CONFIG_SND_HIFIER=m CONFIG_SND_ICE1712=m CONFIG_SND_ICE1724=m CONFIG_SND_INTEL8X0=m CONFIG_SND_INTEL8X0M=m CONFIG_SND_KORG1212=m CONFIG_SND_MAESTRO3=m CONFIG_SND_MIXART=m CONFIG_SND_NM256=m CONFIG_SND_PCXHR=m CONFIG_SND_RIPTIDE=m CONFIG_SND_RME32=m CONFIG_SND_RME96=m CONFIG_SND_RME9652=m CONFIG_SND_SONICVIBES=m CONFIG_SND_TRIDENT=m CONFIG_SND_VIA82XX=m CONFIG_SND_VIA82XX_MODEM=m CONFIG_SND_VIRTUOSO=m CONFIG_SND_VX222=m CONFIG_SND_YMFPCI=m CONFIG_SND_SPI=y CONFIG_SND_USB=y CONFIG_SND_USB_AUDIO=m CONFIG_SND_USB_USX2Y=m CONFIG_SND_USB_CAIAQ=m CONFIG_SND_USB_CAIAQ_INPUT=y # CONFIG_SND_USB_US122L is not set CONFIG_SND_PCMCIA=y CONFIG_SND_VXPOCKET=m CONFIG_SND_PDAUDIOCF=m CONFIG_SND_SOC=m CONFIG_SND_SOC_I2C_AND_SPI=m # CONFIG_SND_SOC_ALL_CODECS is not set CONFIG_SOUND_PRIME=m CONFIG_SOUND_OSS=m # CONFIG_SOUND_TRACEINIT is not set CONFIG_SOUND_DMAP=y CONFIG_SOUND_SSCAPE=m CONFIG_SOUND_VMIDI=m CONFIG_SOUND_TRIX=m CONFIG_SOUND_MSS=m CONFIG_SOUND_MPU401=m CONFIG_SOUND_PAS=m CONFIG_SOUND_PSS=m CONFIG_PSS_MIXER=y # CONFIG_PSS_HAVE_BOOT is not set CONFIG_SOUND_SB=m CONFIG_SOUND_YM3812=m CONFIG_SOUND_UART6850=m CONFIG_SOUND_AEDSP16=m CONFIG_SC6600=y CONFIG_SC6600_JOY=y CONFIG_SC6600_CDROM=4 CONFIG_SC6600_CDROMBASE=0 CONFIG_SOUND_KAHLUA=m CONFIG_AC97_BUS=m CONFIG_HID_SUPPORT=y CONFIG_HID=m # CONFIG_HID_DEBUG is not set CONFIG_HIDRAW=y # # USB Input Devices # CONFIG_USB_HID=m # CONFIG_HID_PID is not set CONFIG_USB_HIDDEV=y # # Special HID drivers # CONFIG_HID_COMPAT=y CONFIG_HID_A4TECH=m CONFIG_HID_APPLE=m CONFIG_HID_BELKIN=m CONFIG_HID_CHERRY=m CONFIG_HID_CHICONY=m CONFIG_HID_CYPRESS=m CONFIG_HID_EZKEY=m CONFIG_HID_GYRATION=m CONFIG_HID_LOGITECH=m # CONFIG_LOGITECH_FF is not set # CONFIG_LOGIRUMBLEPAD2_FF is not set CONFIG_HID_MICROSOFT=m CONFIG_HID_MONTEREY=m CONFIG_HID_NTRIG=m CONFIG_HID_PANTHERLORD=m # CONFIG_PANTHERLORD_FF is not set CONFIG_HID_PETALYNX=m CONFIG_HID_SAMSUNG=m CONFIG_HID_SONY=m CONFIG_HID_SUNPLUS=m # CONFIG_GREENASIA_FF is not set CONFIG_HID_TOPSEED=m # CONFIG_THRUSTMASTER_FF is not set # CONFIG_ZEROPLUS_FF is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=m # CONFIG_USB_DEBUG is not set # CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set # # Miscellaneous USB options # CONFIG_USB_DEVICEFS=y # CONFIG_USB_DEVICE_CLASS is not set # CONFIG_USB_DYNAMIC_MINORS is not set CONFIG_USB_SUSPEND=y # CONFIG_USB_OTG is not set CONFIG_USB_MON=m # CONFIG_USB_WUSB is not set # CONFIG_USB_WUSB_CBAF is not set # # USB Host Controller Drivers # CONFIG_USB_C67X00_HCD=m CONFIG_USB_EHCI_HCD=m CONFIG_USB_EHCI_ROOT_HUB_TT=y CONFIG_USB_EHCI_TT_NEWSCHED=y # CONFIG_USB_OXU210HP_HCD is not set CONFIG_USB_ISP116X_HCD=m CONFIG_USB_ISP1760_HCD=m CONFIG_USB_OHCI_HCD=m # CONFIG_USB_OHCI_HCD_SSB is not set # CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set # CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set CONFIG_USB_OHCI_LITTLE_ENDIAN=y CONFIG_USB_UHCI_HCD=m CONFIG_USB_U132_HCD=m CONFIG_USB_SL811_HCD=m CONFIG_USB_SL811_CS=m CONFIG_USB_R8A66597_HCD=m # CONFIG_USB_HWA_HCD is not set # # Enable Host or Gadget support to see Inventra options # # # USB Device Class drivers # CONFIG_USB_ACM=m CONFIG_USB_PRINTER=m CONFIG_USB_WDM=m # CONFIG_USB_TMC is not set # # NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed; # # # see USB_STORAGE Help for more information # CONFIG_USB_STORAGE=m # CONFIG_USB_STORAGE_DEBUG is not set CONFIG_USB_STORAGE_DATAFAB=y CONFIG_USB_STORAGE_FREECOM=y CONFIG_USB_STORAGE_ISD200=y CONFIG_USB_STORAGE_USBAT=y CONFIG_USB_STORAGE_SDDR09=y CONFIG_USB_STORAGE_SDDR55=y CONFIG_USB_STORAGE_JUMPSHOT=y CONFIG_USB_STORAGE_ALAUDA=y # CONFIG_USB_STORAGE_ONETOUCH is not set CONFIG_USB_STORAGE_KARMA=y # CONFIG_USB_STORAGE_CYPRESS_ATACB is not set CONFIG_USB_LIBUSUAL=y # # USB Imaging devices # CONFIG_USB_MDC800=m CONFIG_USB_MICROTEK=m # # USB port drivers # CONFIG_USB_USS720=m CONFIG_USB_SERIAL=m CONFIG_USB_EZUSB=y CONFIG_USB_SERIAL_GENERIC=y CONFIG_USB_SERIAL_AIRCABLE=m CONFIG_USB_SERIAL_ARK3116=m CONFIG_USB_SERIAL_BELKIN=m CONFIG_USB_SERIAL_CH341=m CONFIG_USB_SERIAL_WHITEHEAT=m CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m CONFIG_USB_SERIAL_CP2101=m CONFIG_USB_SERIAL_CYPRESS_M8=m CONFIG_USB_SERIAL_EMPEG=m CONFIG_USB_SERIAL_FTDI_SIO=m CONFIG_USB_SERIAL_FUNSOFT=m CONFIG_USB_SERIAL_VISOR=m CONFIG_USB_SERIAL_IPAQ=m # CONFIG_USB_SERIAL_IR is not set CONFIG_USB_SERIAL_EDGEPORT=m CONFIG_USB_SERIAL_EDGEPORT_TI=m CONFIG_USB_SERIAL_GARMIN=m CONFIG_USB_SERIAL_IPW=m # CONFIG_USB_SERIAL_IUU is not set CONFIG_USB_SERIAL_KEYSPAN_PDA=m CONFIG_USB_SERIAL_KEYSPAN=m CONFIG_USB_SERIAL_KLSI=m CONFIG_USB_SERIAL_KOBIL_SCT=m CONFIG_USB_SERIAL_MCT_U232=m CONFIG_USB_SERIAL_MOS7720=m CONFIG_USB_SERIAL_MOS7840=m CONFIG_USB_SERIAL_MOTOROLA=m CONFIG_USB_SERIAL_NAVMAN=m CONFIG_USB_SERIAL_PL2303=m CONFIG_USB_SERIAL_OTI6858=m CONFIG_USB_SERIAL_SPCP8X5=m CONFIG_USB_SERIAL_HP4X=m CONFIG_USB_SERIAL_SAFE=m # CONFIG_USB_SERIAL_SAFE_PADDED is not set # CONFIG_USB_SERIAL_SIEMENS_MPI is not set CONFIG_USB_SERIAL_SIERRAWIRELESS=m CONFIG_USB_SERIAL_TI=m CONFIG_USB_SERIAL_CYBERJACK=m CONFIG_USB_SERIAL_XIRCOM=m CONFIG_USB_SERIAL_OPTION=m CONFIG_USB_SERIAL_OMNINET=m # CONFIG_USB_SERIAL_OPTICON is not set CONFIG_USB_SERIAL_DEBUG=m # # USB Miscellaneous drivers # CONFIG_USB_EMI62=m CONFIG_USB_EMI26=m CONFIG_USB_ADUTUX=m # CONFIG_USB_SEVSEG is not set CONFIG_USB_RIO500=m CONFIG_USB_LEGOTOWER=m CONFIG_USB_LCD=m CONFIG_USB_BERRY_CHARGE=m CONFIG_USB_LED=m CONFIG_USB_CYPRESS_CY7C63=m CONFIG_USB_CYTHERM=m CONFIG_USB_PHIDGET=m CONFIG_USB_PHIDGETKIT=m CONFIG_USB_PHIDGETMOTORCONTROL=m CONFIG_USB_PHIDGETSERVO=m CONFIG_USB_IDMOUSE=m CONFIG_USB_FTDI_ELAN=m CONFIG_USB_APPLEDISPLAY=m CONFIG_USB_SISUSBVGA=m # CONFIG_USB_SISUSBVGA_CON is not set CONFIG_USB_LD=m CONFIG_USB_TRANCEVIBRATOR=m CONFIG_USB_IOWARRIOR=m # CONFIG_USB_TEST is not set CONFIG_USB_ISIGHTFW=m # CONFIG_USB_VST is not set CONFIG_USB_ATM=m CONFIG_USB_SPEEDTOUCH=m CONFIG_USB_CXACRU=m CONFIG_USB_UEAGLEATM=m CONFIG_USB_XUSBATM=m # # OTG and related infrastructure # # CONFIG_USB_GPIO_VBUS is not set # CONFIG_UWB is not set CONFIG_MMC=m # CONFIG_MMC_DEBUG is not set # CONFIG_MMC_UNSAFE_RESUME is not set # # MMC/SD/SDIO Card Drivers # CONFIG_MMC_BLOCK=m CONFIG_MMC_BLOCK_BOUNCE=y CONFIG_SDIO_UART=m # CONFIG_MMC_TEST is not set # # MMC/SD/SDIO Host Controller Drivers # CONFIG_MMC_SDHCI=m CONFIG_MMC_SDHCI_PCI=m CONFIG_MMC_RICOH_MMC=m CONFIG_MMC_WBSD=m CONFIG_MMC_TIFM_SD=m CONFIG_MMC_SPI=m CONFIG_MMC_SDRICOH_CS=m # CONFIG_MEMSTICK is not set CONFIG_NEW_LEDS=y CONFIG_LEDS_CLASS=m # # LED drivers # # CONFIG_LEDS_ALIX2 is not set CONFIG_LEDS_PCA9532=m CONFIG_LEDS_GPIO=m # CONFIG_LEDS_CLEVO_MAIL is not set CONFIG_LEDS_PCA955X=m # # LED Triggers # CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_TIMER=m CONFIG_LEDS_TRIGGER_HEARTBEAT=m # CONFIG_LEDS_TRIGGER_BACKLIGHT is not set CONFIG_LEDS_TRIGGER_DEFAULT_ON=m # CONFIG_ACCESSIBILITY is not set CONFIG_EDAC=y # # Reporting subsystems # # CONFIG_EDAC_DEBUG is not set CONFIG_EDAC_MM_EDAC=m CONFIG_EDAC_E752X=m CONFIG_EDAC_I82975X=m CONFIG_EDAC_I3000=m # CONFIG_EDAC_X38 is not set # CONFIG_EDAC_I5400 is not set CONFIG_EDAC_I5000=m CONFIG_EDAC_I5100=m CONFIG_RTC_LIB=y CONFIG_RTC_CLASS=y CONFIG_RTC_HCTOSYS=y CONFIG_RTC_HCTOSYS_DEVICE="rtc0" # CONFIG_RTC_DEBUG is not set # # RTC interfaces # CONFIG_RTC_INTF_SYSFS=y CONFIG_RTC_INTF_PROC=y CONFIG_RTC_INTF_DEV=y CONFIG_RTC_INTF_DEV_UIE_EMUL=y CONFIG_RTC_DRV_TEST=m # # I2C RTC drivers # CONFIG_RTC_DRV_DS1307=m CONFIG_RTC_DRV_DS1374=m CONFIG_RTC_DRV_DS1672=m CONFIG_RTC_DRV_MAX6900=m CONFIG_RTC_DRV_RS5C372=m CONFIG_RTC_DRV_ISL1208=m CONFIG_RTC_DRV_X1205=m CONFIG_RTC_DRV_PCF8563=m CONFIG_RTC_DRV_PCF8583=m CONFIG_RTC_DRV_M41T80=m CONFIG_RTC_DRV_M41T80_WDT=y # CONFIG_RTC_DRV_S35390A is not set CONFIG_RTC_DRV_FM3130=m # CONFIG_RTC_DRV_RX8581 is not set # # SPI RTC drivers # CONFIG_RTC_DRV_M41T94=m CONFIG_RTC_DRV_DS1305=m # CONFIG_RTC_DRV_DS1390 is not set CONFIG_RTC_DRV_MAX6902=m # CONFIG_RTC_DRV_R9701 is not set CONFIG_RTC_DRV_RS5C348=m # CONFIG_RTC_DRV_DS3234 is not set # # Platform RTC drivers # CONFIG_RTC_DRV_CMOS=y # CONFIG_RTC_DRV_DS1286 is not set # CONFIG_RTC_DRV_DS1511 is not set CONFIG_RTC_DRV_DS1553=m CONFIG_RTC_DRV_DS1742=m CONFIG_RTC_DRV_STK17TA8=m CONFIG_RTC_DRV_M48T86=m # CONFIG_RTC_DRV_M48T35 is not set CONFIG_RTC_DRV_M48T59=m # CONFIG_RTC_DRV_BQ4802 is not set CONFIG_RTC_DRV_V3020=m # # on-CPU RTC drivers # CONFIG_DMADEVICES=y # # DMA Devices # CONFIG_INTEL_IOATDMA=m CONFIG_DMA_ENGINE=y # # DMA Clients # CONFIG_NET_DMA=y # CONFIG_DMATEST is not set CONFIG_DCA=m CONFIG_AUXDISPLAY=y CONFIG_KS0108=m CONFIG_KS0108_PORT=0x378 CONFIG_KS0108_DELAY=2 CONFIG_CFAG12864B=m CONFIG_CFAG12864B_RATE=20 CONFIG_UIO=m CONFIG_UIO_CIF=m CONFIG_UIO_PDRV=m CONFIG_UIO_PDRV_GENIRQ=m CONFIG_UIO_SMX=m # CONFIG_UIO_SERCOS3 is not set CONFIG_XEN_BALLOON=y CONFIG_XEN_SCRUB_PAGES=y CONFIG_XEN_DEV_EVTCHN=y CONFIG_XEN_BACKEND=y CONFIG_XEN_BLKDEV_BACKEND=y CONFIG_XEN_NETDEV_BACKEND=y CONFIG_XENFS=y CONFIG_XEN_COMPAT_XENFS=y CONFIG_XEN_XENBUS_FRONTEND=y # CONFIG_STAGING is not set CONFIG_X86_PLATFORM_DEVICES=y CONFIG_ACER_WMI=m CONFIG_ASUS_LAPTOP=m CONFIG_FUJITSU_LAPTOP=m # CONFIG_FUJITSU_LAPTOP_DEBUG is not set CONFIG_HP_WMI=m CONFIG_MSI_LAPTOP=m # CONFIG_PANASONIC_LAPTOP is not set CONFIG_COMPAL_LAPTOP=m CONFIG_SONY_LAPTOP=m CONFIG_SONYPI_COMPAT=y CONFIG_THINKPAD_ACPI=m # CONFIG_THINKPAD_ACPI_DEBUGFACILITIES is not set # CONFIG_THINKPAD_ACPI_DEBUG is not set CONFIG_THINKPAD_ACPI_BAY=y CONFIG_THINKPAD_ACPI_VIDEO=y CONFIG_THINKPAD_ACPI_HOTKEY_POLL=y CONFIG_INTEL_MENLOW=m CONFIG_ACPI_WMI=m # CONFIG_ACPI_ASUS is not set # CONFIG_ACPI_TOSHIBA is not set # # Firmware Drivers # CONFIG_EDD=y CONFIG_EDD_OFF=y CONFIG_FIRMWARE_MEMMAP=y CONFIG_DELL_RBU=m CONFIG_DCDBAS=m CONFIG_DMIID=y CONFIG_ISCSI_IBFT_FIND=y CONFIG_ISCSI_IBFT=m # # File systems # CONFIG_EXT2_FS=m CONFIG_EXT2_FS_XATTR=y CONFIG_EXT2_FS_POSIX_ACL=y CONFIG_EXT2_FS_SECURITY=y # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=m CONFIG_EXT3_FS_XATTR=y CONFIG_EXT3_FS_POSIX_ACL=y CONFIG_EXT3_FS_SECURITY=y # CONFIG_EXT4_FS is not set CONFIG_JBD=m # CONFIG_JBD_DEBUG is not set CONFIG_JBD2=m # CONFIG_JBD2_DEBUG is not set CONFIG_FS_MBCACHE=m CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set # CONFIG_REISERFS_PROC_INFO is not set CONFIG_REISERFS_FS_XATTR=y CONFIG_REISERFS_FS_POSIX_ACL=y CONFIG_REISERFS_FS_SECURITY=y CONFIG_JFS_FS=m CONFIG_JFS_POSIX_ACL=y CONFIG_JFS_SECURITY=y # CONFIG_JFS_DEBUG is not set CONFIG_JFS_STATISTICS=y CONFIG_FS_POSIX_ACL=y CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=m CONFIG_XFS_QUOTA=y CONFIG_XFS_POSIX_ACL=y CONFIG_XFS_RT=y # CONFIG_XFS_DEBUG is not set CONFIG_GFS2_FS=m CONFIG_GFS2_FS_LOCKING_DLM=m CONFIG_OCFS2_FS=m CONFIG_OCFS2_FS_O2CB=m CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m CONFIG_OCFS2_FS_STATS=y CONFIG_OCFS2_DEBUG_MASKLOG=y # CONFIG_OCFS2_DEBUG_FS is not set # CONFIG_OCFS2_FS_POSIX_ACL is not set # CONFIG_BTRFS_FS is not set CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y CONFIG_QUOTA=y CONFIG_QUOTA_NETLINK_INTERFACE=y CONFIG_PRINT_QUOTA_WARNING=y CONFIG_QUOTA_TREE=m CONFIG_QFMT_V1=m CONFIG_QFMT_V2=m CONFIG_QUOTACTL=y CONFIG_AUTOFS_FS=m CONFIG_AUTOFS4_FS=m CONFIG_FUSE_FS=m CONFIG_GENERIC_ACL=y # # CD-ROM/DVD Filesystems # CONFIG_ISO9660_FS=m CONFIG_JOLIET=y CONFIG_ZISOFS=y CONFIG_UDF_FS=m CONFIG_UDF_NLS=y # # DOS/FAT/NT Filesystems # CONFIG_FAT_FS=m CONFIG_MSDOS_FS=m CONFIG_VFAT_FS=m CONFIG_FAT_DEFAULT_CODEPAGE=437 CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_NTFS_FS=m # CONFIG_NTFS_DEBUG is not set # CONFIG_NTFS_RW is not set # # Pseudo filesystems # CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y CONFIG_TMPFS_POSIX_ACL=y # CONFIG_HUGETLBFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_CONFIGFS_FS=m CONFIG_MISC_FILESYSTEMS=y CONFIG_ADFS_FS=m # CONFIG_ADFS_FS_RW is not set CONFIG_AFFS_FS=m CONFIG_ECRYPT_FS=m CONFIG_HFS_FS=m CONFIG_HFSPLUS_FS=m CONFIG_BEFS_FS=m # CONFIG_BEFS_DEBUG is not set CONFIG_BFS_FS=m CONFIG_EFS_FS=m CONFIG_UBIFS_FS=m CONFIG_UBIFS_FS_XATTR=y # CONFIG_UBIFS_FS_ADVANCED_COMPR is not set CONFIG_UBIFS_FS_LZO=y CONFIG_UBIFS_FS_ZLIB=y # CONFIG_UBIFS_FS_DEBUG is not set CONFIG_CRAMFS=y CONFIG_SQUASHFS=m # CONFIG_SQUASHFS_EMBEDDED is not set CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE=3 CONFIG_VXFS_FS=m CONFIG_MINIX_FS=m CONFIG_OMFS_FS=m CONFIG_HPFS_FS=m CONFIG_QNX4FS_FS=m CONFIG_ROMFS_FS=m CONFIG_SYSV_FS=m CONFIG_UFS_FS=m # CONFIG_UFS_FS_WRITE is not set # CONFIG_UFS_DEBUG is not set CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=m CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y CONFIG_NFS_V4=y CONFIG_NFSD=m CONFIG_NFSD_V2_ACL=y CONFIG_NFSD_V3=y CONFIG_NFSD_V3_ACL=y CONFIG_NFSD_V4=y CONFIG_LOCKD=m CONFIG_LOCKD_V4=y CONFIG_EXPORTFS=m CONFIG_NFS_ACL_SUPPORT=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=m CONFIG_SUNRPC_GSS=m # CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=m CONFIG_RPCSEC_GSS_SPKM3=m CONFIG_SMB_FS=m # CONFIG_SMB_NLS_DEFAULT is not set CONFIG_CIFS=m # CONFIG_CIFS_STATS is not set CONFIG_CIFS_WEAK_PW_HASH=y CONFIG_CIFS_UPCALL=y # CONFIG_CIFS_XATTR is not set # CONFIG_CIFS_DEBUG2 is not set CONFIG_CIFS_EXPERIMENTAL=y CONFIG_CIFS_DFS_UPCALL=y CONFIG_NCP_FS=m CONFIG_NCPFS_PACKET_SIGNING=y CONFIG_NCPFS_IOCTL_LOCKING=y CONFIG_NCPFS_STRONG=y CONFIG_NCPFS_NFS_NS=y CONFIG_NCPFS_OS2_NS=y # CONFIG_NCPFS_SMALLDOS is not set CONFIG_NCPFS_NLS=y CONFIG_NCPFS_EXTRAS=y CONFIG_CODA_FS=m CONFIG_AFS_FS=m # CONFIG_AFS_DEBUG is not set # # Partition Types # CONFIG_PARTITION_ADVANCED=y CONFIG_ACORN_PARTITION=y # CONFIG_ACORN_PARTITION_CUMANA is not set # CONFIG_ACORN_PARTITION_EESOX is not set CONFIG_ACORN_PARTITION_ICS=y # CONFIG_ACORN_PARTITION_ADFS is not set # CONFIG_ACORN_PARTITION_POWERTEC is not set CONFIG_ACORN_PARTITION_RISCIX=y CONFIG_OSF_PARTITION=y CONFIG_AMIGA_PARTITION=y CONFIG_ATARI_PARTITION=y CONFIG_MAC_PARTITION=y CONFIG_MSDOS_PARTITION=y CONFIG_BSD_DISKLABEL=y CONFIG_MINIX_SUBPARTITION=y CONFIG_SOLARIS_X86_PARTITION=y CONFIG_UNIXWARE_DISKLABEL=y CONFIG_LDM_PARTITION=y # CONFIG_LDM_DEBUG is not set CONFIG_SGI_PARTITION=y CONFIG_ULTRIX_PARTITION=y CONFIG_SUN_PARTITION=y CONFIG_KARMA_PARTITION=y CONFIG_EFI_PARTITION=y CONFIG_SYSV68_PARTITION=y CONFIG_NLS=y CONFIG_NLS_DEFAULT="cp437" CONFIG_NLS_CODEPAGE_437=m CONFIG_NLS_CODEPAGE_737=m CONFIG_NLS_CODEPAGE_775=m CONFIG_NLS_CODEPAGE_850=m CONFIG_NLS_CODEPAGE_852=m CONFIG_NLS_CODEPAGE_855=m CONFIG_NLS_CODEPAGE_857=m CONFIG_NLS_CODEPAGE_860=m CONFIG_NLS_CODEPAGE_861=m CONFIG_NLS_CODEPAGE_862=m CONFIG_NLS_CODEPAGE_863=m CONFIG_NLS_CODEPAGE_864=m CONFIG_NLS_CODEPAGE_865=m CONFIG_NLS_CODEPAGE_866=m CONFIG_NLS_CODEPAGE_869=m CONFIG_NLS_CODEPAGE_936=m CONFIG_NLS_CODEPAGE_950=m CONFIG_NLS_CODEPAGE_932=m CONFIG_NLS_CODEPAGE_949=m CONFIG_NLS_CODEPAGE_874=m CONFIG_NLS_ISO8859_8=m CONFIG_NLS_CODEPAGE_1250=m CONFIG_NLS_CODEPAGE_1251=m CONFIG_NLS_ASCII=m CONFIG_NLS_ISO8859_1=m CONFIG_NLS_ISO8859_2=m CONFIG_NLS_ISO8859_3=m CONFIG_NLS_ISO8859_4=m CONFIG_NLS_ISO8859_5=m CONFIG_NLS_ISO8859_6=m CONFIG_NLS_ISO8859_7=m CONFIG_NLS_ISO8859_9=m CONFIG_NLS_ISO8859_13=m CONFIG_NLS_ISO8859_14=m CONFIG_NLS_ISO8859_15=m CONFIG_NLS_KOI8_R=m CONFIG_NLS_KOI8_U=m CONFIG_NLS_UTF8=m CONFIG_DLM=m # CONFIG_DLM_DEBUG is not set # # Kernel hacking # CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_PRINTK_TIME=y CONFIG_ALLOW_WARNINGS=y # CONFIG_ENABLE_WARN_DEPRECATED is not set # CONFIG_ENABLE_MUST_CHECK is not set CONFIG_FRAME_WARN=2048 CONFIG_MAGIC_SYSRQ=y CONFIG_UNUSED_SYMBOLS=y CONFIG_DEBUG_FS=y # CONFIG_HEADERS_CHECK is not set CONFIG_DEBUG_KERNEL=y # CONFIG_DEBUG_SHIRQ is not set CONFIG_DETECT_SOFTLOCKUP=y # CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 CONFIG_DETECT_HUNG_TASK=y # CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0 CONFIG_SCHED_DEBUG=y CONFIG_SCHEDSTATS=y CONFIG_TIMER_STATS=y # CONFIG_DEBUG_OBJECTS is not set # CONFIG_DEBUG_SLAB is not set # CONFIG_DEBUG_RT_MUTEXES is not set # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set # CONFIG_DEBUG_LOCK_ALLOC is not set # CONFIG_PROVE_LOCKING is not set # CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set CONFIG_STACKTRACE=y # CONFIG_DEBUG_KOBJECT is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_VIRTUAL is not set # CONFIG_DEBUG_WRITECOUNT is not set CONFIG_DEBUG_MEMORY_INIT=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set CONFIG_ARCH_WANT_FRAME_POINTERS=y CONFIG_FRAME_POINTER=y # CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_KPROBES_SANITY_TEST is not set # CONFIG_BACKTRACE_SELF_TEST is not set # CONFIG_DEBUG_BLOCK_EXT_DEVT is not set # CONFIG_LKDTM is not set # CONFIG_FAULT_INJECTION is not set CONFIG_LATENCYTOP=y CONFIG_SYSCTL_SYSCALL_CHECK=y CONFIG_USER_STACKTRACE_SUPPORT=y CONFIG_NOP_TRACER=y CONFIG_HAVE_FUNCTION_TRACER=y CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_HAVE_HW_BRANCH_TRACER=y CONFIG_RING_BUFFER=y CONFIG_TRACING=y # # Tracers # # CONFIG_FUNCTION_TRACER is not set # CONFIG_IRQSOFF_TRACER is not set # CONFIG_SYSPROF_TRACER is not set # CONFIG_SCHED_TRACER is not set CONFIG_CONTEXT_SWITCH_TRACER=y # CONFIG_BOOT_TRACER is not set # CONFIG_TRACE_BRANCH_PROFILING is not set # CONFIG_POWER_TRACER is not set # CONFIG_STACK_TRACER is not set # CONFIG_HW_BRANCH_TRACER is not set # CONFIG_KMEMTRACE is not set # CONFIG_WORKQUEUE_TRACER is not set CONFIG_BLK_DEV_IO_TRACE=y # CONFIG_FTRACE_STARTUP_TEST is not set # CONFIG_MMIOTRACE is not set # CONFIG_PROVIDE_OHCI1394_DMA_INIT is not set # CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set CONFIG_STRICT_DEVMEM=y CONFIG_X86_VERBOSE_BOOTUP=y CONFIG_EARLY_PRINTK=y # CONFIG_EARLY_PRINTK_DBGP is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set # CONFIG_DEBUG_PER_CPU_MAPS is not set # CONFIG_X86_PTDUMP is not set CONFIG_DEBUG_RODATA=y # CONFIG_DEBUG_RODATA_TEST is not set # CONFIG_DEBUG_NX_TEST is not set # CONFIG_IOMMU_DEBUG is not set CONFIG_HAVE_MMIOTRACE_SUPPORT=y CONFIG_IO_DELAY_TYPE_0X80=0 CONFIG_IO_DELAY_TYPE_0XED=1 CONFIG_IO_DELAY_TYPE_UDELAY=2 CONFIG_IO_DELAY_TYPE_NONE=3 # CONFIG_IO_DELAY_0X80 is not set CONFIG_IO_DELAY_0XED=y # CONFIG_IO_DELAY_UDELAY is not set # CONFIG_IO_DELAY_NONE is not set CONFIG_DEFAULT_IO_DELAY_TYPE=1 # CONFIG_KMEMCHECK is not set # CONFIG_DEBUG_BOOT_PARAMS is not set # CONFIG_CPA_DEBUG is not set CONFIG_OPTIMIZE_INLINING=y # # Security options # CONFIG_KEYS=y # CONFIG_KEYS_DEBUG_PROC_KEYS is not set CONFIG_SECURITY=y CONFIG_SECURITYFS=y CONFIG_SECURITY_NETWORK=y # CONFIG_SECURITY_NETWORK_XFRM is not set # CONFIG_SECURITY_PATH is not set CONFIG_SECURITY_FILE_CAPABILITIES=y CONFIG_SECURITY_DEFAULT_MMAP_MIN_ADDR=0 CONFIG_SECURITY_SELINUX=y CONFIG_SECURITY_SELINUX_BOOTPARAM=y CONFIG_SECURITY_SELINUX_BOOTPARAM_VALUE=0 CONFIG_SECURITY_SELINUX_DISABLE=y CONFIG_SECURITY_SELINUX_DEVELOP=y CONFIG_SECURITY_SELINUX_AVC_STATS=y CONFIG_SECURITY_SELINUX_CHECKREQPROT_VALUE=1 # CONFIG_SECURITY_SELINUX_POLICYDB_VERSION_MAX is not set CONFIG_SECURITY_SMACK=y CONFIG_XOR_BLOCKS=m CONFIG_ASYNC_CORE=m CONFIG_ASYNC_MEMCPY=m CONFIG_ASYNC_XOR=m CONFIG_CRYPTO=y # # Crypto core or helper # # CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_ALGAPI2=y CONFIG_CRYPTO_AEAD=m CONFIG_CRYPTO_AEAD2=y CONFIG_CRYPTO_BLKCIPHER=m CONFIG_CRYPTO_BLKCIPHER2=y CONFIG_CRYPTO_HASH=y CONFIG_CRYPTO_HASH2=y CONFIG_CRYPTO_RNG=m CONFIG_CRYPTO_RNG2=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_MANAGER2=y CONFIG_CRYPTO_GF128MUL=m CONFIG_CRYPTO_NULL=m CONFIG_CRYPTO_CRYPTD=m CONFIG_CRYPTO_AUTHENC=m CONFIG_CRYPTO_TEST=m # # Authenticated Encryption with Associated Data # CONFIG_CRYPTO_CCM=m CONFIG_CRYPTO_GCM=m CONFIG_CRYPTO_SEQIV=m # # Block modes # CONFIG_CRYPTO_CBC=m CONFIG_CRYPTO_CTR=m CONFIG_CRYPTO_CTS=m CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_LRW=m CONFIG_CRYPTO_PCBC=m CONFIG_CRYPTO_XTS=m # # Hash modes # CONFIG_CRYPTO_HMAC=y CONFIG_CRYPTO_XCBC=m # # Digest # CONFIG_CRYPTO_CRC32C=m # CONFIG_CRYPTO_CRC32C_INTEL is not set CONFIG_CRYPTO_MD4=m CONFIG_CRYPTO_MD5=y CONFIG_CRYPTO_MICHAEL_MIC=m CONFIG_CRYPTO_RMD128=m CONFIG_CRYPTO_RMD160=m CONFIG_CRYPTO_RMD256=m CONFIG_CRYPTO_RMD320=m CONFIG_CRYPTO_SHA1=m CONFIG_CRYPTO_SHA256=m CONFIG_CRYPTO_SHA512=m CONFIG_CRYPTO_TGR192=m CONFIG_CRYPTO_WP512=m # # Ciphers # CONFIG_CRYPTO_AES=m CONFIG_CRYPTO_AES_X86_64=m CONFIG_CRYPTO_ANUBIS=m CONFIG_CRYPTO_ARC4=m CONFIG_CRYPTO_BLOWFISH=m CONFIG_CRYPTO_CAMELLIA=m CONFIG_CRYPTO_CAST5=m CONFIG_CRYPTO_CAST6=m CONFIG_CRYPTO_DES=m CONFIG_CRYPTO_FCRYPT=m CONFIG_CRYPTO_KHAZAD=m CONFIG_CRYPTO_SALSA20=m CONFIG_CRYPTO_SALSA20_X86_64=m CONFIG_CRYPTO_SEED=m CONFIG_CRYPTO_SERPENT=m CONFIG_CRYPTO_TEA=m CONFIG_CRYPTO_TWOFISH=m CONFIG_CRYPTO_TWOFISH_COMMON=m CONFIG_CRYPTO_TWOFISH_X86_64=m # # Compression # CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_LZO=m # # Random Number Generation # # CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRYPTO_HW=y CONFIG_CRYPTO_DEV_HIFN_795X=m CONFIG_CRYPTO_DEV_HIFN_795X_RNG=y CONFIG_HAVE_KVM=y CONFIG_VIRTUALIZATION=y # CONFIG_KVM is not set # CONFIG_VIRTIO_PCI is not set # CONFIG_VIRTIO_BALLOON is not set # # Library routines # CONFIG_BITREVERSE=y CONFIG_GENERIC_FIND_FIRST_BIT=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_FIND_LAST_BIT=y CONFIG_CRC_CCITT=m CONFIG_CRC16=m CONFIG_CRC_T10DIF=m CONFIG_CRC_ITU_T=m CONFIG_CRC32=y CONFIG_CRC7=m CONFIG_LIBCRC32C=m CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=m CONFIG_LZO_COMPRESS=m CONFIG_LZO_DECOMPRESS=m CONFIG_REED_SOLOMON=m CONFIG_REED_SOLOMON_DEC16=y CONFIG_TEXTSEARCH=y CONFIG_TEXTSEARCH_KMP=m CONFIG_TEXTSEARCH_BM=m CONFIG_TEXTSEARCH_FSM=m CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y CONFIG_CHECK_SIGNATURE=y --- On Wed, 2/18/09, Jeremy Fitzhardinge <jeremy@goop.org> wrote: From: Jeremy Fitzhardinge <jeremy@goop.org> Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip To: "Andrew Lyon" <andrew.lyon@gmail.com> Cc: bderzhavets@yahoo.com, "xen-devel@lists.xensource.com" <xen-devel@lists.xensource.com>, "Marc - A. Dahlhaus [ Administration | Westermann GmbH ]" <mad@wol.de> Date: Wednesday, February 18, 2009, 3:04 PM Andrew Lyon wrote:> I built from the git tree this morning and still get the same ahci and > piix problems on my test box (a dell optiplex 755), is that problem > supposed to be fixed? >Well, ahci is still a problem for me, though apparently it works fine for Boris. But PIIX should be working. Can you repost your boot logs + .config again? Also, Boris, could you post your .config? Thanks, J _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
On Wed, Feb 18, 2009 at 02:39:44PM -0800, Jeremy Fitzhardinge wrote:> Pasi Kärkkäinen wrote: > >On Tue, Feb 17, 2009 at 10:40:54AM -0800, Jeremy Fitzhardinge wrote: > > > >>Pasi Kärkkäinen wrote: > >> > >>>On Tue, Feb 17, 2009 at 05:31:57AM -0800, Boris Derzhavets wrote: > >>> > >>> > >>>>Hardware config:- > >>>>C2D E8400, 8 GB RAM, ASUS P5K Premium/WIFI (Intel P35+Intel ICH9R), > >>>>2x250 SATA Seagate Barracuda (no RAID). Bios settings for ICH9R - AHCI. > >>>>Details here:- > >>>>http://bderzhavets.wordpress.com/2009/02/17/setup-xen-unstable-dom0-via-2629-rc5-pv_ops-enabled-kernel-on-intel-sataahci/ > >>>> > >>>> > >>>> > >>>Thanks! > >>> > >>>So it seems you''re running 64 bit dom0 OS/hypervisor.. > >>> > >>>64 bit seems to work better atm than 32 bit.. > >>> > >>> > >>I tend to focus on 64-bit, and Ian Campbell has been looking at 32-bit. > >>In theory there shouldn''t be all that much difference between them. > >>There have been a few issues, but they''re sharing 90+% of the code. (In > >>practice I''m interested in any bug reports, esp comparing 32 and 64-bit > >>behaviour). > >> > >> > > > >I''m testing 32bit PAE dom0 on 32bit PAE hypervisor. > > > >Today, with 2.6.29-rc5, I managed to boot my dom0 into login prompt! > >I haven''t been able to get this working earlier.. congratulations! > > > >I had to use ''noapic'' dom0 kernel parameter though.. without ''noapic'' I''m > >seeing > >the same IRQ problems with ata_piix than earlier. > > > > Hm, interesting. One change I made in the last few days was making gsis > map 1:1 with irqs, like the native kernel. I wonder if that helps in > your case. That said, I''m not quite sure how its working with noapic; I > would have thought that it wouldn''t go through the Xen-hooked paths that > way... > > Oh, you''re using ahci, not piix - and that works with noapic. Hm, I > should try that. >I have ahci controller onboard, but I''m not using it atm. The (only) disk I have is connected to ata_piix controller..> Can you start xend and a domain? >I''ll try that today!> >My dom0 kernel config: > >http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.29-rc5-tip-dom0 > > > >My grub.conf: > >http://pasik.reaktio.net/xen/pv_ops-dom0-debug/grub.conf > > > >Working dom0 bootlog with ''noapic'': > >http://pasik.reaktio.net/xen/pv_ops-dom0-debug/pv_ops-dom0-bootlog-13-xen331-linux-2.6.29-rc5-noapic.txt > > > What does your /proc/interrupts look like in this case? >Will check.> >Failing dom0 bootlog (without ''noapic''): > >http://pasik.reaktio.net/xen/pv_ops-dom0-debug/pv_ops-dom0-bootlog-12-xen331-linux-2.6.29-rc5.txt > > > > Do you think you could boot from a usb device or something and see if > you can get /proc/interrupts for this as well? >If I have enough time today I''ll try making some USB root device.. -- Pasi _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Andrew Lyon wrote:> I built from the git tree this morning and still get the same ahci and > piix problems on my test box (a dell optiplex 755), is that problem > supposed to be fixed? >Try now. Gerd noticed a pretty major bug in interrupt setup, and fixing it has made AHCI work for me. It will likely fix your piix. J _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Just in case, i did same snapshot on my box :- root@ServerXen331:~# cat /proc/interrupts CPU0 CPU1 1: 2382 0 xen-pirq-pirq i8042 4: 23 0 xen-pirq-pirq 8: 0 0 xen-pirq-pirq rtc0 9: 0 0 xen-pirq-pirq acpi 16: 0 0 xen-pirq-pirq ahci, uhci_hcd:usb1, eth1 17: 1484598 0 xen-pirq-pirq pata_jmicron, peth0 18: 303892 0 xen-pirq-pirq uhci_hcd:usb3, uhci_hcd:usb6, ehci_hcd:usb7 19: 3 0 xen-pirq-pirq uhci_hcd:usb5, ohci1394 21: 0 0 xen-pirq-pirq uhci_hcd:usb2 22: 369205 0 xen-pirq-pirq ahci, HDA Intel 23: 2 0 xen-pirq-pirq uhci_hcd:usb4, ehci_hcd:usb8 24: 1763255 0 xen-dyn-virq timer0 25: 4802 0 xen-dyn-ipi spinlock0 26: 111735 0 xen-dyn-ipi resched0 27: 0 0 xen-dyn-ipi callfunc0 28: 0 0 xen-dyn-virq debug0 29: 194 0 xen-dyn-ipi callfuncsingle0 30: 0 1763173 xen-dyn-virq timer1 31: 0 14283 xen-dyn-ipi spinlock1 32: 0 155653 xen-dyn-ipi resched1 33: 0 0 xen-dyn-ipi callfunc1 34: 0 0 xen-dyn-virq debug1 35: 0 866 xen-dyn-ipi callfuncsingle1 36: 11249 0 xen-dyn-event xenbus 38: 6301 0 xen-dyn-event evtchn:xenstored 39: 21 0 xen-dyn-event evtchn:xenstored 40: 221 0 xen-dyn-event evtchn:xenstored 41: 5 0 xen-dyn-event evtchn:qemu-dm 42: 985 0 xen-dyn-event evtchn:qemu-dm 43: 68 0 xen-dyn-event evtchn:qemu-dm 44: 2672 0 xen-dyn-event blkif-backend 45: 24 0 xen-dyn-event vif8.0 NMI: 0 0 Non-maskable interrupts LOC: 0 0 Local timer interrupts CNT: 0 0 Performance counter interrupts RES: 111736 155653 Rescheduling interrupts CAL: 194 866 Function call interrupts TLB: 0 0 TLB shootdowns SPU: 0 0 Spurious interrupts ERR: 0 MIS: 0 --- On Thu, 2/19/09, Jeremy Fitzhardinge <jeremy@goop.org> wrote: From: Jeremy Fitzhardinge <jeremy@goop.org> Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip To: "Andrew Lyon" <andrew.lyon@gmail.com> Cc: bderzhavets@yahoo.com, "xen-devel@lists.xensource.com" <xen-devel@lists.xensource.com>, "Marc - A. Dahlhaus [ Administration | Westermann GmbH ]" <mad@wol.de> Date: Thursday, February 19, 2009, 12:30 PM Andrew Lyon wrote:> I built from the git tree this morning and still get the same ahci and > piix problems on my test box (a dell optiplex 755), is that problem > supposed to be fixed? >Try now. Gerd noticed a pretty major bug in interrupt setup, and fixing it has made AHCI work for me. It will likely fix your piix. J _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
On Thu, Feb 19, 2009 at 5:30 PM, Jeremy Fitzhardinge <jeremy@goop.org> wrote:> Andrew Lyon wrote: >> >> I built from the git tree this morning and still get the same ahci and >> piix problems on my test box (a dell optiplex 755), is that problem >> supposed to be fixed? >> > > Try now. Gerd noticed a pretty major bug in interrupt setup, and fixing it > has made AHCI work for me. It will likely fix your piix. > > J >Awesome, the kernel booted and ahci is working normally, and piix isnt actually used on this system as all the devices are sata. xend failed to start saying it was not a privileged domain, first thing I am going to try there is upgrading to Xen 3.3.1 final as I am still running rc4 on my test box, but what is the minimum Xen version to use pv_ops dom0? Full boot log: GNU GRUB version 0.97 (635K lower / 3404798K upper memory) +-------------------------------------------------------------------------+ | Xen 3.3 / Linux 2.6.27.5-xen.hg | | Xen 3.3 / Linux 2.6.29-rc5-tip | | Linux 2.6.29-rc5-tip | | Xen 3.3.1rc4 / Linux 2.6.27-xen-r5 | | Gentoo Linux 2.6.27-r4 | | | | | | | | | | | | | | | +-------------------------------------------------------------------------+ Use the ^ and v keys to select which entry is highlighted. Press enter to boot the selected OS, ''e'' to edit the commands before booting, or ''c'' for a command-line. Booting ''Xen 3.3 / Linux 2.6.29-rc5-tip'' root (hd0,0) Filesystem type is ext2fs, partition type 0x83 kernel /xen.gz com1=115200,8n1 console=com1,vga mem=3G dom0_mem=512M [Multiboot-elf, <0x100000:0xfc6a8:0x98958>, shtab=0x295078, entry=0x100000] module /vmlinux.bin.gz-2.6.29-rc5-tip root=/dev/sda2 console=hvc0 earlyprink=xe n pci=nomsi panic=5 [Multiboot-module @ 0x296000, 0xc13c58 bytes] __ __ _____ _____ _ _ _ \ \/ /___ _ __ |___ / |___ / / | _ __ ___| || | \ // _ \ ''_ \ |_ \ |_ \ | |__| ''__/ __| || |_ / \ __/ | | | ___) | ___) || |__| | | (__|__ _| /_/\_\___|_| |_| |____(_)____(_)_| |_| \___| |_| (XEN) Xen version 3.3.1-rc4 (root@) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.2)) Wed Dec 31 08:59:56 GMT 2008 (XEN) Latest ChangeSet: unavailable (XEN) Command line: com1=115200,8n1 console=com1,vga mem=3G dom0_mem=512M (XEN) Video information: (XEN) VGA is text mode 80x25, font 8x16 (XEN) VBE/DDC methods: V2; EDID transfer time: 1 seconds (XEN) Disc information: (XEN) Found 1 MBR signatures (XEN) Found 1 EDD information structures (XEN) Truncating memory map to 3145728kB (XEN) Xen-e820 RAM map: (XEN) 0000000000000000 - 000000000009ec00 (usable) (XEN) 00000000000f0000 - 0000000000100000 (reserved) (XEN) 0000000000100000 - 00000000c0000000 (usable) (XEN) System RAM: 3071MB (3145336kB) (XEN) ACPI: RSDP 000FEC00, 0024 (r2 DELL ) (XEN) ACPI: XSDT 000FC5B3, 008C (r1 DELL B9K 15 ASL 61) (XEN) ACPI: FACP 000FC6E3, 00F4 (r3 DELL B9K 15 ASL 61) (XEN) ACPI: DSDT FFF76BF6, 4596 (r1 DELL dt_ex 1000 INTL 20050624) (XEN) ACPI: FACS CFDFF800, 0040 (XEN) ACPI: SSDT FFF7B2AB, 00AA (r1 DELL st_ex 1000 INTL 20050624) (XEN) ACPI: APIC 000FC7D7, 0092 (r1 DELL B9K 15 ASL 61) (XEN) ACPI: BOOT 000FC869, 0028 (r1 DELL B9K 15 ASL 61) (XEN) ACPI: ASF! 000FC891, 0096 (r32 DELL B9K 15 ASL 61) (XEN) ACPI: MCFG 000FC927, 003E (r1 DELL B9K 15 ASL 61) (XEN) ACPI: HPET 000FC965, 0038 (r1 DELL B9K 15 ASL 61) (XEN) ACPI: TCPA 000FCBC1, 0032 (r1 DELL B9K 15 ASL 61) (XEN) ACPI: DMAR 000FCBF3, 00D0 (r1 DELL B9K 15 ASL 61) (XEN) ACPI: SLIC 000FC99D, 0176 (r1 DELL B9K 15 ASL 61) (XEN) ACPI: SSDT CFDFF840, 01F9 (r1 DpgPmm Cpu0Ist 11 INTL 20050624) (XEN) ACPI: SSDT CFDFFC49, 01F9 (r1 DpgPmm Cpu1Ist 11 INTL 20050624) (XEN) ACPI: SSDT CFE00052, 0140 (r1 DpgPmm CpuPm 10 INTL 20050624) (XEN) Xen heap: 14MB (14664kB) (XEN) Domain heap initialised (XEN) Processor #0 6:15 APIC version 20 (XEN) Processor #1 6:15 APIC version 20 (XEN) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 (XEN) Enabling APIC mode: Flat. Using 1 I/O APICs (XEN) Using scheduler: SMP Credit Scheduler (credit) (XEN) Detected 2394.034 MHz processor. (XEN) APIC Access emulated, slow!! (XEN) HVM: VMX enabled (XEN) CPU0: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06 (XEN) Booting processor 1/1 eip 8c000 (XEN) APIC Access emulated, slow!! (XEN) CPU1: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06 (XEN) Total of 2 processors activated. (XEN) ENABLING IO-APIC IRQs (XEN) -> Using new ACK method (XEN) checking TSC synchronization across 2 CPUs: passed. (XEN) Platform timer is 14.318MHz HPET (XEN) Brought up 2 CPUs (XEN) I/O virtualisation disabled (XEN) *** LOADING DOMAIN 0 *** (XEN) Xen kernel: 64-bit, lsb, compat32 (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x200000 -> 0x90d714 (XEN) PHYSICAL MEMORY ARRANGEMENT: (XEN) Dom0 alloc.: 00000000ba000000->00000000bb000000 (126976 pages to be allocated) (XEN) VIRTUAL MEMORY ARRANGEMENT: (XEN) Loaded kernel: ffffffff80200000->ffffffff8090d714 (XEN) Init. ramdisk: ffffffff8090e000->ffffffff8090e000 (XEN) Phys-Mach map: ffffffff8090e000->ffffffff80a0e000 (XEN) Start info: ffffffff80a0e000->ffffffff80a0e4a4 (XEN) Page tables: ffffffff80a0f000->ffffffff80a18000 (XEN) Boot stack: ffffffff80a18000->ffffffff80a19000 (XEN) TOTAL: ffffffff80000000->ffffffff80c00000 (XEN) ENTRY ADDRESS: ffffffff807b7200 (XEN) Dom0 has maximum 2 VCPUs (XEN) Scrubbing Free RAM: .........................done. (XEN) Xen trace buffers: disabled (XEN) Std. Loglevel: Errors and warnings (XEN) Guest Loglevel: Nothing (Rate-limited: Errors and warnings) (XEN) Xen is relinquishing VGA console. (XEN) *** Serial input -> DOM0 (type ''CTRL-a'' three times to switch input to Xen) (XEN) Freed 104kB init memory. mapping kernel into physical memory Xen: setup ISA identity maps about to get started... (XEN) ioapic_guest_write: apic=0, pin=2, old_irq=0, new_irq=-1 (XEN) ioapic_guest_write: old_entry=000009f0, new_entry=00010900 (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ! (XEN) ioapic_guest_write: apic=0, pin=4, old_irq=4, new_irq=-1 (XEN) ioapic_guest_write: old_entry=000009f1, new_entry=00010900 (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ! Linux version 2.6.29-rc5-tip (root@localhost) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.2)) #2 SMP Fri Feb 20 08:50:15 GMT 2009 Command line: root=/dev/sda2 console=hvc0 earlyprink=xen pci=nomsi panic=5 KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD Centaur CentaurHauls BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000000009ec00 (usable) Xen: 00000000000a0000 - 0000000000100000 (reserved) Xen: 0000000000100000 - 000000000090e000 (usable) Xen: 000000000090e000 - 0000000000a0f000 (reserved) Xen: 0000000000a0f000 - 0000000020000000 (usable) DMI 2.5 present. last_pfn = 0x20000 max_arch_pfn = 0x100000000 init_memory_mapping: 0000000000000000-0000000020000000 last_map_addr: 20000000 end: 20000000 ACPI: RSDP 000FEC00, 0024 (r2 DELL ) ACPI: XSDT 000FC5B3, 008C (r1 DELL B9K 15 ASL 61) ACPI: FACP 000FC6E3, 00F4 (r3 DELL B9K 15 ASL 61) ACPI Warning (tbfadt-0568): 32/64X length mismatch in Gpe0Block: 128/64 [20081204] FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4) ACPI: DSDT FFF76BF6, 4596 (r1 DELL dt_ex 1000 INTL 20050624) ACPI: FACS CFDFF800, 0040 ACPI: SSDT FFF7B2AB, 00AA (r1 DELL st_ex 1000 INTL 20050624) ACPI: APIC 000FC7D7, 0092 (r1 DELL B9K 15 ASL 61) ACPI: BOOT 000FC869, 0028 (r1 DELL B9K 15 ASL 61) ACPI: ASF! 000FC891, 0096 (r32 DELL B9K 15 ASL 61) ACPI: MCFG 000FC927, 003E (r1 DELL B9K 15 ASL 61) ACPI: HPET 000FC965, 0038 (r1 DELL B9K 15 ASL 61) ACPI: TCPA 000FCBC1, 0032 (r1 DELL B9K 15 ASL 61) ACPI: DMAR 000FCBF3, 00D0 (r1 DELL B9K 15 ASL 61) ACPI: SLIC 000FC99D, 0176 (r1 DELL B9K 15 ASL 61) ACPI: SSDT CFDFF840, 01F9 (r1 DpgPmm Cpu0Ist 11 INTL 20050624) ACPI: SSDT CFDFFC49, 01F9 (r1 DpgPmm Cpu1Ist 11 INTL 20050624) ACPI: SSDT CFE00052, 0140 (r1 DpgPmm CpuPm 10 INTL 20050624) (5 early reservations) ==> bootmem [0000000000 - 0020000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000a0f000 - 0000a18000] XEN PAGETABLES ==> [0000a0f000 - 0000a18000] #2 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] #3 [0000200000 - 000090d714] TEXT DATA BSS ==> [0000200000 - 000090d714] #4 [0000a18000 - 0000b0e000] PGTABLE ==> [0000a18000 - 0000b0e000] found SMP MP-table at [ffff8800000fe710] fe710 Zone PFN ranges: DMA 0x00000000 -> 0x00001000 DMA32 0x00001000 -> 0x00100000 Normal 0x00100000 -> 0x00100000 Movable zone start PFN for each node early_node_map[3] active PFN ranges 0: 0x00000000 -> 0x0000009e 0: 0x00000100 -> 0x0000090e 0: 0x00000a0f -> 0x00020000 ACPI: PM-Timer IO Port: 0x808 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x05] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x01] disabled) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x02] disabled) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x03] disabled) ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1]) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) Using ACPI (MADT) for SMP configuration information ACPI: HPET id: 0x8086a301 base: 0xfed00000 SMP: Allowing 2 CPUs, 0 hotplug CPUs Allocating PCI resources starting at 30000000 (gap: 20000000:e0000000) NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:2 nr_node_ids:1 PERCPU: Allocating 90112 bytes of per cpu data Xen: using vcpu_info placement Built 1 zonelists in Zone order, mobility grouping on. Total pages: 126860 Kernel command line: root=/dev/sda2 console=hvc0 earlyprink=xen pci=nomsi panic=5 Initializing CPU#0 NR_IRQS:384 xen: allocated irq 9 for acpi 9 xen_allocate_pirq: returning irq 9 for gsi 9 PID hash table entries: 2048 (order: 11, 16384 bytes) Detected 2394.004 MHz processor. Console: colour VGA+ 80x25 console [hvc0] enabled Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) Checking aperture... No AGP bridge found PCI-DMA: Using software bounce buffering for IO (SWIOTLB) Placing 64MB software IO TLB between ffff880001848000 - ffff880005848000 software IO TLB at phys 0x1848000 - 0x5848000 Memory: 439844k/524288k available (3560k kernel code, 1420k absent, 82488k reserved, 2014k data, 484k init) SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 installing Xen timer for CPU 0 Calibrating delay loop (skipped), value calculated using timer frequency.. 4788.00 BogoMIPS (lpj=2394004) Mount-cache hash table entries: 256 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 SMP alternatives: switching to UP code ACPI: Core revision 20081204 cpu 0 spinlock event irq 25 installing Xen timer for CPU 1 cpu 1 spinlock event irq 31 SMP alternatives: switching to SMP code Initializing CPU#1 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 Brought up 2 CPUs khelper used greatest stack depth: 6664 bytes left net_namespace: 600 bytes Booting paravirtualized kernel on Xen Xen version: 3.3.1-rc4 (preserve-AD) (dom0) Grant table initialized Time: 8:58:07 Date: 02/20/09 NET: Registered protocol family 16 khelper used greatest stack depth: 6640 bytes left xenbus_probe_init ok khelper used greatest stack depth: 6160 bytes left ACPI FADT declares the system doesn''t support PCIe ASPM, so disable it ACPI: bus type pci registered PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 PCI: Not using MMCONFIG. PCI: Using configuration type 1 for base access bio: create slab <bio-0> at 0 ACPI: Interpreter enabled ACPI: (supports S0 S1 S3 S5) ACPI: Using IOAPIC for interrupt routing PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 PCI: BIOS Bug: MCFG area at e0000000 is not reserved in ACPI motherboard resources PCI: Not using MMCONFIG. ACPI: ACPI Dock Station Driver: 1 docks/bays found ACPI: PCI Root Bridge [PCI0] (0000:00) pci 0000:00:01.0: PME# supported from D0 D3hot D3cold pci 0000:00:01.0: PME# disabled pci 0000:00:03.0: PME# supported from D0 D3hot D3cold pci 0000:00:03.0: PME# disabled pci 0000:00:19.0: PME# supported from D0 D3hot D3cold pci 0000:00:19.0: PME# disabled pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold pci 0000:00:1a.7: PME# disabled pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold pci 0000:00:1b.0: PME# disabled pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold pci 0000:00:1c.0: PME# disabled pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold pci 0000:00:1d.7: PME# disabled pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0880-08bf claimed by ICH6 GPIO pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0c00 (mask 007f) pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 00e0 (mask 0007) pci 0000:00:1f.2: PME# supported from D3hot pci 0000:00:1f.2: PME# disabled pci 0000:00:1e.0: transparent bridge ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 9 10 11 12 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 15) ACPI Warning (tbutils-0242): Incorrect checksum in table [TCPA] - 00, should be 87 [20081204] xen_balloon: Initialising balloon driver. SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing cfg80211: Using static regulatory domain info cfg80211: Regulatory domain: US (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) cfg80211: Calling CRDA for country: US Xen: Initializing Xen DMA ops Xen: Enabling DMA fallback to swiotlb pnp: PnP ACPI init ACPI: bus type pnp registered pnp 00:01: io resource (0x800-0x85f) overlaps 0000:00:1f.0 BAR 7 (0x800-0x87f), disabling pnp 00:01: io resource (0x860-0x8ff) overlaps 0000:00:1f.0 BAR 7 (0x800-0x87f), disabling xen_allocate_pirq: returning irq 13 for gsi 13 xen_set_ioapic_routing: irq 13 gsi 13 vector 120 ioapic 0 pin 13 triggering 0 polarity 0 xen_allocate_pirq: returning irq 8 for gsi 8 xen_set_ioapic_routing: irq 8 gsi 8 vector 80 ioapic 0 pin 8 triggering 0 polarity 0 xen_allocate_pirq: returning irq 7 for gsi 7 xen_set_ioapic_routing: irq 7 gsi 7 vector 72 ioapic 0 pin 7 triggering 0 polarity 0 xen_allocate_pirq: returning irq 4 for gsi 4 xen_set_ioapic_routing: irq 4 gsi 4 vector 241 ioapic 0 pin 4 triggering 0 polarity 0 pnp: PnP ACPI: found 9 devices ACPI: ACPI bus type pnp unregistered system 00:01: ioport range 0xc00-0xc7f has been reserved pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 pci 0000:00:01.0: IO window: 0xd000-0xdfff pci 0000:00:01.0: MEM window: 0xfe900000-0xfeafffff pci 0000:00:01.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02 pci 0000:00:1c.0: IO window: disabled pci 0000:00:1c.0: MEM window: 0xfe800000-0xfe8fffff pci 0000:00:1c.0: PREFETCH window: disabled pci 0000:00:1e.0: PCI bridge, secondary bus 0000:03 pci 0000:00:1e.0: IO window: disabled pci 0000:00:1e.0: MEM window: disabled pci 0000:00:1e.0: PREFETCH window: disabled xen_set_ioapic_routing: irq 16 gsi 16 vector 160 ioapic 0 pin 16 triggering 1 polarity 1 pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 xen_allocate_pirq: returning irq 16 for gsi 16 xen_set_ioapic_routing: irq 16 gsi 16 vector 160 ioapic 0 pin 16 triggering 1 polarity 1 pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 NET: Registered protocol family 2 IP route cache hash table entries: 16384 (order: 5, 131072 bytes) TCP established hash table entries: 65536 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 65536 bind 65536) TCP reno registered NET: Registered protocol family 1 Simple Boot Flag at 0x7a set to 0x1 audit: initializing netlink socket (disabled) type=2000 audit(1235120289.531:1): initialized VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) msgmni has been set to 1024 alg: No test for stdrng (krng) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pci_hotplug: PCI Hot Plug PCI Core version: 0.5 input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1 ACPI: Power Button (CM) [VBTN] xenbus_probe_backend_init bus registered ok xenbus_probe_frontend_init bus registered ok Event-channel device installed. ***blkif_init *** netif_init registering netback Non-volatile memory driver v1.3 Linux agpgart interface v0.103 [drm] Initialized drm 1.1.0 20060810 brd: module loaded loop: module loaded tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> console [netcon0] enabled netconsole: network logging started Loading iSCSI transport class v2.0-870. Driver ''sd'' needs updating - please use bus_type methods Driver ''sr'' needs updating - please use bus_type methods xen_set_ioapic_routing: irq 18 gsi 18 vector 168 ioapic 0 pin 18 triggering 1 polarity 1 ahci 0000:00:1f.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x27 impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pmp pio slum part ems scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci scsi4 : ahci scsi5 : ahci ata1: SATA max UDMA/133 irq_stat 0x00000040, connection status changed irq 18 ata2: SATA max UDMA/133 irq_stat 0x00000040, connection status changed irq 18 ata3: SATA max UDMA/133 abar m2048@0xff970000 port 0xff970200 irq 18 ata4: DUMMY ata5: DUMMY ata6: SATA max UDMA/133 abar m2048@0xff970000 port 0xff970380 irq 18 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-6: WDC WD360GD-00FLA2, 31.08F31, max UDMA/133 ata1.00: 72303840 sectors, multi 0: LBA48 ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD360GD-00FL 31.0 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 72303840 512-byte hardware sectors: (37.0 GB/34.4 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn''t support DPO or FUA sd 0:0:0:0: [sda] 72303840 512-byte hardware sectors: (37.0 GB/34.4 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn''t support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata2.00: ATAPI: HL-DT-ST DVD+/-RW GSA-H73N, B103, max UDMA/100 ata2.00: configured for UDMA/100 scsi 1:0:0:0: CD-ROM HL-DT-ST DVD+-RW GSA-H73N B103 PQ: 0 ANSI: 5 sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi generic sg1 type 5 ata3: SATA link down (SStatus 4 SControl 300) ata6: SATA link down (SStatus 4 SControl 300) ehci_hcd: USB 2.0 ''Enhanced'' Host Controller (EHCI) Driver xen_set_ioapic_routing: irq 22 gsi 22 vector 176 ioapic 0 pin 22 triggering 1 polarity 1 ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1a.7: debug port 1 ehci_hcd 0000:00:1a.7: irq 22, io mem 0xfebd9c00 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.29-rc5-tip ehci_hcd usb usb1: SerialNumber: 0000:00:1a.7 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected xen_set_ioapic_routing: irq 23 gsi 23 vector 184 ioapic 0 pin 23 triggering 1 polarity 1 ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: irq 23, io mem 0xff980800 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: EHCI Host Controller usb usb2: Manufacturer: Linux 2.6.29-rc5-tip ehci_hcd usb usb2: SerialNumber: 0000:00:1d.7 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 6 ports detected ohci_hcd: USB 1.1 ''Open'' Host Controller (OHCI) Driver uhci_hcd: USB Universal Host Controller Interface driver xen_allocate_pirq: returning irq 16 for gsi 16 xen_set_ioapic_routing: irq 16 gsi 16 vector 160 ioapic 0 pin 16 triggering 1 polarity 1 uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1a.0: detected 2 ports uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000ff20 usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: UHCI Host Controller usb usb3: Manufacturer: Linux 2.6.29-rc5-tip uhci_hcd usb usb3: SerialNumber: 0000:00:1a.0 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected xen_set_ioapic_routing: irq 17 gsi 17 vector 192 ioapic 0 pin 17 triggering 1 polarity 1 uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1a.1: detected 2 ports uhci_hcd 0000:00:1a.1: irq 17, io base 0x0000ff00 usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: UHCI Host Controller usb usb4: Manufacturer: Linux 2.6.29-rc5-tip uhci_hcd usb usb4: SerialNumber: 0000:00:1a.1 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected xen_allocate_pirq: returning irq 23 for gsi 23 xen_set_ioapic_routing: irq 23 gsi 23 vector 184 ioapic 0 pin 23 triggering 1 polarity 1 (XEN) ioapic_guest_write: apic=0, pin=23, old_irq=23, new_irq=23 (XEN) ioapic_guest_write: old_entry=0000a9b8, new_entry=0001a9b8 (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.0: detected 2 ports uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000ff80 usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: UHCI Host Controller usb usb5: Manufacturer: Linux 2.6.29-rc5-tip uhci_hcd usb usb5: SerialNumber: 0000:00:1d.0 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected xen_allocate_pirq: returning irq 17 for gsi 17 xen_set_ioapic_routing: irq 17 gsi 17 vector 192 ioapic 0 pin 17 triggering 1 polarity 1 (XEN) ioapic_guest_write: apic=0, pin=17, old_irq=17, new_irq=17 (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0 (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6 uhci_hcd 0000:00:1d.1: detected 2 ports uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000ff60 usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb6: Product: UHCI Host Controller usb usb6: Manufacturer: Linux 2.6.29-rc5-tip uhci_hcd usb usb6: SerialNumber: 0000:00:1d.1 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected xen_allocate_pirq: returning irq 18 for gsi 18 xen_set_ioapic_routing: irq 18 gsi 18 vector 168 ioapic 0 pin 18 triggering 1 polarity 1 (XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18 (XEN) ioapic_guest_write: old_entry=0000a9a8, new_entry=0001a9a8 (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7 uhci_hcd 0000:00:1d.2: detected 2 ports uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ff40 usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb7: Product: UHCI Host Controller usb usb7: Manufacturer: Linux 2.6.29-rc5-tip uhci_hcd usb usb7: SerialNumber: 0000:00:1d.2 usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 2 ports detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver libusual PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com cpuidle: using governor ladder dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) TCP cubic registered NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. IO APIC resources could be not be allocated. registered taskstats version 1 Magic number: 13:765:978 usb 2-2: new high speed USB device using ehci_hcd and address 2 usb 2-2: New USB device found, idVendor=0644, idProduct=0200 usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-2: Product: CA-200 usb 2-2: Manufacturer: TEAC usb 2-2: SerialNumber: 0000030664A1 usb 2-2: configuration #1 chosen from 1 choice scsi6 : SCSI emulation for USB Mass Storage devices md: Waiting for all devices to be available before autodetect md: If you don''t use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: Scanned 0 and added 0 devices. md: autorun ... md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3 FS on sda2, internal journal EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) on device 8:2. Freeing unused kernel memory: 484k freed Write protecting the kernel read-only data: 5168k usb 2-5: new high speed USB device using ehci_hcd and address 3 khelper used greatest stack depth: 5848 bytes left usb 2-5: New USB device found, idVendor=0424, idProduct=2504 usb 2-5: New USB device strings: Mfr=0, Product=0, SerialNumber=0 usb 2-5: configuration #1 chosen from 1 choice hub 2-5:1.0: USB hub found hub 2-5:1.0: 4 ports detected INIT: version 2.86 booting usb 3-1: new low speed USB device using uhci_hcd and address 2 consoletype used greatest stack depth: 5792 bytes left stty used greatest stack depth: 4368 bytes left Gentoo Linux; http://www.gentoo.org/ Copyright 1999-2007 Gentoo Foundation; Distributed under the GPLv2 Press I to enter interactive boot mode * Mounting proc at /proc ... [ ok ] * Mounting sysfs at /sys ... [ ok ] * Mounting /dev ... [ ok ] * Starting udevd ... [ ok ] * Populating /dev with existing devices through uevents ... [ ok ] * Waiting for uevents to be processed ... [ ok ] * Mounting devpts at /dev/pts ... [ ok ] * Remounting root filesystem read-only ... [ ok ] * Checking root filesystem .../dev/sda2: clean, 391047/1756512 files, 1781580/7012352 blocks [ ok ] * Remounting root filesystem read/write ... [ ok ] * Using /etc/modules.autoload.d/kernel-2.6 as config: * Loading module e1000e ... [ ok ] * Autoloaded 1 module(s) * Setting up the Logical Volume Manager ... [ ok ] * Checking all filesystems .../dev/sda1: clean, 42/24096 files, 17172/96356 blocks [ ok ] * Mounting local filesystems ... [ ok ] * Mounting USB device filesystem (usbfs) ... [ ok ] * Mounting misc binary format filesystem ... [ ok ] * Activating (possible) swap ... [ ok ] * Your TIMEZONE in /etc/conf.d/clock is still set to Factory! * Setting system clock using the hardware clock [UTC] ... * Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method.Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. * Failed to set clock You will need to set the clock yourself [ !! ] * Configuring kernel parameters ... [ ok ] * Updating environment ... [ ok ] * Cleaning /var/lock, /var/run ... [ ok ] * Wiping /tmp directory ... [ ok ] * Device initiated services: udev-postmount * Setting hostname to localhost ... [ ok ] * Loading key mappings ... [ ok ] * Setting terminal encoding to UTF-8 ... [ ok ] * Setting user font ... [ ok ] * Starting lo * Bringing up lo * 127.0.0.1/8 [ ok ] * Adding routes * 127.0.0.0/8 ... [ ok ] * Initializing random number generator ... [ ok ] INIT: Entering runlevel: 3 * Starting eth0 * Bringing up eth0 * 10.0.4.3/21 [ ok ] * Adding routes * default via 10.0.0.1 ... [ ok ] * Mounting network filesystems ... [ ok ] * Can''t start xend - this is not a privileged domain. * Starting sshd ... [ ok ] * Starting vixie-cron ... [ ok ] * Starting local ... [ ok ] _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Andrew Lyon wrote:> Awesome, the kernel booted and ahci is working normally, and piix > isnt actually used on this system as all the devices are sata. > > xend failed to start saying it was not a privileged domain, first > thing I am going to try there is upgrading to Xen 3.3.1 final as I am > still running rc4 on my test box, but what is the minimum Xen version > to use pv_ops dom0?Try adding this line to /etc/fstab: xen /proc/xen xenfs defaults 0 0 vanilla 3.3.1 isn''t going to work, you need a few patches backported from unstable. Current rawhide package has these changesets: xen-backport-hg18782.patch xen-backport-hg19075.patch xen-backport-hg19108.patch xen-backport-hg19109.patch xen-backport-hg19110.patch cheers, Gerd _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
On Fri, Feb 20, 2009 at 9:36 AM, Gerd Hoffmann <kraxel@redhat.com> wrote:> Andrew Lyon wrote: >> Awesome, the kernel booted and ahci is working normally, and piix >> isnt actually used on this system as all the devices are sata. >> >> xend failed to start saying it was not a privileged domain, first >> thing I am going to try there is upgrading to Xen 3.3.1 final as I am >> still running rc4 on my test box, but what is the minimum Xen version >> to use pv_ops dom0? > > Try adding this line to /etc/fstab: > > xen /proc/xen xenfs defaults 0 0 > > vanilla 3.3.1 isn''t going to work, you need a few patches backported > from unstable. Current rawhide package has these changesets: > > xen-backport-hg18782.patch > xen-backport-hg19075.patch > xen-backport-hg19108.patch > xen-backport-hg19109.patch > xen-backport-hg19110.patch > > cheers, > Gerd > >Thanks Gerd, I have upgraded to 3.4 unstable, I tried creating a hvm domain using a existing vm with windows xp, it started ok but I cannot connect to the vnc display, no process is listening on the vnc port, has the configuration changed for vnc? I''ve checked the wiki and there is no mention of vnc. Andy _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Andrew Lyon wrote:> Awesome, the kernel booted and ahci is working normally, and piix > isnt actually used on this system as all the devices are sata. >Good to hear.> xend failed to start saying it was not a privileged domain, first > thing I am going to try there is upgrading to Xen 3.3.1 final as I am > still running rc4 on my test box, but what is the minimum Xen version > to use pv_ops dom0? >Did you forget to mount /proc/xen?> root (hd0,0) > Filesystem type is ext2fs, partition type 0x83 > kernel /xen.gz com1=115200,8n1 console=com1,vga mem=3G dom0_mem=512M > [Multiboot-elf, <0x100000:0xfc6a8:0x98958>, shtab=0x295078, entry=0x100000] > module /vmlinux.bin.gz-2.6.29-rc5-tip root=/dev/sda2 console=hvc0 earlyprink=xe > n pci=nomsi panic=5 >With current versions of Xen you can just use your bzImage for the kernel - no need for vmlinuz-XXX.gz as well. J _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
On Fri, Feb 20, 2009 at 2:58 PM, Jeremy Fitzhardinge <jeremy@goop.org> wrote:> Andrew Lyon wrote: >> >> Awesome, the kernel booted and ahci is working normally, and piix >> isnt actually used on this system as all the devices are sata. >> > > Good to hear. > >> xend failed to start saying it was not a privileged domain, first >> thing I am going to try there is upgrading to Xen 3.3.1 final as I am >> still running rc4 on my test box, but what is the minimum Xen version >> to use pv_ops dom0? >> > > Did you forget to mount /proc/xen?Yes, I mounted it and now I can start xend.> >> root (hd0,0) >> Filesystem type is ext2fs, partition type 0x83 >> kernel /xen.gz com1=115200,8n1 console=com1,vga mem=3G dom0_mem=512M >> [Multiboot-elf, <0x100000:0xfc6a8:0x98958>, shtab=0x295078, >> entry=0x100000] >> module /vmlinux.bin.gz-2.6.29-rc5-tip root=/dev/sda2 console=hvc0 >> earlyprink=xe >> n pci=nomsi panic=5 >> > > With current versions of Xen you can just use your bzImage for the kernel - > no need for vmlinuz-XXX.gz as well.noted.> > J >I think I could not connect to hvm domain using vnc because of a bug Yuji Shimada has already found: "If we assign the device that doesn''t have Power Management Capability Structure to guest domain, qemu accesses NULL pointer." I am getting the same error "xs_read(/local/domain/0/device-model/2/xen_extended_power_mgmt): read error" Yuji said "I''ll submit the patch to fix the bug ASAP", I will try again once his patch is submitted. Andy _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
On Fri, Feb 20, 2009 at 3:39 PM, Andrew Lyon <andrew.lyon@gmail.com> wrote:> On Fri, Feb 20, 2009 at 2:58 PM, Jeremy Fitzhardinge <jeremy@goop.org> wrote: >> Andrew Lyon wrote: >>> >>> Awesome, the kernel booted and ahci is working normally, and piix >>> isnt actually used on this system as all the devices are sata. >>> >> >> Good to hear. >> >>> xend failed to start saying it was not a privileged domain, first >>> thing I am going to try there is upgrading to Xen 3.3.1 final as I am >>> still running rc4 on my test box, but what is the minimum Xen version >>> to use pv_ops dom0? >>> >> >> Did you forget to mount /proc/xen? > > Yes, I mounted it and now I can start xend. > >> >>> root (hd0,0) >>> Filesystem type is ext2fs, partition type 0x83 >>> kernel /xen.gz com1=115200,8n1 console=com1,vga mem=3G dom0_mem=512M >>> [Multiboot-elf, <0x100000:0xfc6a8:0x98958>, shtab=0x295078, >>> entry=0x100000] >>> module /vmlinux.bin.gz-2.6.29-rc5-tip root=/dev/sda2 console=hvc0 >>> earlyprink=xe >>> n pci=nomsi panic=5 >>> >> >> With current versions of Xen you can just use your bzImage for the kernel - >> no need for vmlinuz-XXX.gz as well. > > noted. > >> >> J >> > > I think I could not connect to hvm domain using vnc because of a bug > Yuji Shimada has already found: > > "If we assign the device that doesn''t have Power Management Capability > Structure to guest domain, qemu accesses NULL pointer." > > I am getting the same error > "xs_read(/local/domain/0/device-model/2/xen_extended_power_mgmt): read > error" > > Yuji said "I''ll submit the patch to fix the bug ASAP", I will try > again once his patch is submitted. > > Andy >I have checked the ioemu-remote source that is downloaded when building xen unstable, it seems to be missing this patch: <snip> This patch fixes the segmentation fault on assigning device without Power Management Capability Structure. Please apply this patch after applying the following patch I have submitted. [PATCH] ioemu: Cleanup the code of PCI passthrough. Thanks, -- Yuji Shimada. Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp> diff --git a/hw/pass-through.c b/hw/pass-through.c index 855f69c..305ea59 100644 --- a/hw/pass-through.c +++ b/hw/pass-through.c @@ -1165,7 +1165,7 @@ static void pt_pci_write_config(PCIDevice *d, uint32_t address, uint32_t val, } /* check power state transition flags */ - if (pm_state->flags & PT_FLAG_TRANSITING) + if (pm_state != NULL && pm_state->flags & PT_FLAG_TRANSITING) /* can''t accept untill previous power state transition is completed. * so finished previous request here. */ @@ -1280,7 +1280,7 @@ out: if (!ret) PT_LOG("Error: pci_write_block failed. return value[%d].\n", ret); - if (pm_state->flags & PT_FLAG_TRANSITING) + if (pm_state != NULL && pm_state->flags & PT_FLAG_TRANSITING) /* set QEMUTimer */ qemu_mod_timer(pm_state->pm_timer, (qemu_get_clock(rt_clock) + pm_state->pm_delay)); @@ -1337,7 +1337,7 @@ static uint32_t pt_pci_read_config(PCIDevice *d, uint32_t address, int len) } /* check power state transition flags */ - if (pm_state->flags & PT_FLAG_TRANSITING) + if (pm_state != NULL && pm_state->flags & PT_FLAG_TRANSITING) /* can''t accept untill previous power state transition is completed. * so finished previous request here. */ <snip> I certainly get the same symptom as the user that originally reported this bug: [2009-02-20 19:37:53 19273] WARNING (image:482) domain xptest: device model failure: pid 19342: malfunctioning (closed sentinel), killed; see /var/log/xen/qemu-dm-xptest.log cat /var/log/xen/qemu-dm-xptest.log domid: 3 qemu: the number of cpus is 2 Watching /local/domain/0/device-model/3/logdirty/next-active Watching /local/domain/0/device-model/3/command qemu_map_cache_init nr_buckets = 10000 size 3145728 shared page at pfn feffd buffered io page at pfn feffb Guest uuid = 46f22c82-8a3d-47e3-b9c5-3b5f6eaf7a12 Time offset set 0 populating video RAM at ff000000 mapping video RAM from ff000000 Register xen platform. Done register platform. xs_read(/local/domain/0/device-model/3/xen_extended_power_mgmt): read error medium change watch on `hdc'' (index: 1): I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0 I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0 cirrus vga map change while on lfb mode But the only strange thing is that I am not trying to assign a pci device to the domain. I tried manually applying the patch but it didnt seem to work, I had the same issue when I tried to use James''s gplpv device hiding patch, what is the correct technique for applying patches to ioemu-remote ? the source doesn''t exist until the build process is started, is it possible to manually pull the source and then tell the build process not to download it? Thanks Andy Andy _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
>I have checked the ioemu-remote source that is downloaded when >building xen unstable, it seems to be missing this patch:> <snip>> This patch fixes the segmentation fault on assigning device without > Power Management Capability Structure.************************************************ Where to get <snip> for patching Xen Unstable ? Boris. ************************************************> Please apply this patch after applying the following patch I have > submitted.[PATCH] ioemu: Cleanup the code of PCI passthrough. Thanks, -- Yuji Shimada. Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp> diff --git a/hw/pass-through.c b/hw/pass-through.c index 855f69c..305ea59 100644 --- a/hw/pass-through.c +++ b/hw/pass-through.c @@ -1165,7 +1165,7 @@ static void pt_pci_write_config(PCIDevice *d, uint32_t address, uint32_t val, } /* check power state transition flags */ - if (pm_state->flags & PT_FLAG_TRANSITING) + if (pm_state != NULL && pm_state->flags & PT_FLAG_TRANSITING) /* can''t accept untill previous power state transition is completed. * so finished previous request here. */ @@ -1280,7 +1280,7 @@ out: if (!ret) PT_LOG("Error: pci_write_block failed. return value[%d].\n", ret); - if (pm_state->flags & PT_FLAG_TRANSITING) + if (pm_state != NULL && pm_state->flags & PT_FLAG_TRANSITING) /* set QEMUTimer */ qemu_mod_timer(pm_state->pm_timer, (qemu_get_clock(rt_clock) + pm_state->pm_delay)); @@ -1337,7 +1337,7 @@ static uint32_t pt_pci_read_config(PCIDevice *d, uint32_t address, int len) } /* check power state transition flags */ - if (pm_state->flags & PT_FLAG_TRANSITING) + if (pm_state != NULL && pm_state->flags & PT_FLAG_TRANSITING) /* can''t accept untill previous power state transition is completed. * so finished previous request here. */ From where ? <snip> _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Boris Derzhavets
2009-Feb-21 09:01 UTC
[Xen-devel] Reproduced error when creating Intrepid HVM at Xen Unstable Dom0(vmlinuz-2.6.29-rc5-tip)
After fresh port Xen Unstable:-
[root@ServerXen xen]# ls -l qemu-dm-UbuntuHVM.log
-rwxr-xr-x 1 root root 810 Feb 21 11:29 qemu-dm-UbuntuHVM.log
[root@ServerXen xen]# cat qemu-dm-UbuntuHVM.log
domid: 1
qemu: the number of cpus is 1
config qemu network with xen bridge for tap1.0 eth0
Watching /local/domain/0/device-model/1/logdirty/next-active
Watching /local/domain/0/device-model/1/command
xs_read(): vncpasswd get error.
/vm/eea6ff6e-737f-b453-94e4-c6015c5a9aa0/vncpasswd.
qemu_map_cache_init nr_buckets = 10000 size 3145728
shared page at pfn feffd
buffered io page at pfn feffb
Guest uuid = eea6ff6e-737f-b453-94e4-c6015c5a9aa0
Time offset set 0
populating video RAM at ff000000
mapping video RAM from ff000000
Register xen platform.
Done register platform.
xs_read(/local/domain/0/device-model/1/xen_extended_power_mgmt): read error
medium change watch on `hdc'' (index: 0): /dev/loop0
I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0
cirrus vga map change while on lfb mode
No patching has been done due to zero awareness what to apply.
"If we assign the device that doesn''t have Power Management
Capability
Structure to guest domain, qemu accesses NULL pointer."
I am getting the same error
"xs_read(/local/domain/0/device-model/2/xen_extended_power_mgmt): read
error"
Yuji said "I''ll submit the patch to fix the bug ASAP", I will
try
again once his patch is submitted.
Andy
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
On Fri, Feb 20, 2009 at 9:36 AM, Gerd Hoffmann <kraxel@redhat.com> wrote:> Andrew Lyon wrote: >> Awesome, the kernel booted and ahci is working normally, and piix >> isnt actually used on this system as all the devices are sata. >> >> xend failed to start saying it was not a privileged domain, first >> thing I am going to try there is upgrading to Xen 3.3.1 final as I am >> still running rc4 on my test box, but what is the minimum Xen version >> to use pv_ops dom0? > > Try adding this line to /etc/fstab: > > xen /proc/xen xenfs defaults 0 0 > > vanilla 3.3.1 isn''t going to work, you need a few patches backported > from unstable. Current rawhide package has these changesets: > > xen-backport-hg18782.patch > xen-backport-hg19075.patch > xen-backport-hg19108.patch > xen-backport-hg19109.patch > xen-backport-hg19110.patch > > cheers, > Gerd > >I''ve also tried using 3.3.1 with the backported patches as above, I still get a device model failure error but this time there is no mention of power management: [2009-02-21 12:32:33 3486] WARNING (image:472) domain xptest: device model failure: pid 3766: malfunctioning (closed sentinel), killed; see /var/log/xen/qemu-dm-xptest.log cat /var/log/xen/qemu-dm-xptest.log domid: 1 qemu: the number of cpus is 2 Watching /local/domain/0/device-model/1/logdirty/next-active Watching /local/domain/0/device-model/1/command qemu_map_cache_init nr_buckets = 10000 size 3145728 shared page at pfn 1fffe buffered io page at pfn 1fffc Time offset set 0 Register xen platform. Done register platform. medium change watch on `hdc'' (index: 1): I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0 I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0 Which logfiles do I need to post to investigate this problem? Andy _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Andrew Lyon wrote:> I''ve also tried using 3.3.1 with the backported patches as above, I > still get a device model failure error but this time there is no > mention of power management: > > [2009-02-21 12:32:33 3486] WARNING (image:472) domain xptest: device > model failure: pid 3766: malfunctioning (closed sentinel), killed; see > /var/log/xen/qemu-dm-xptest.log >IanJ would have more of an idea about this stuff than me. J> > cat /var/log/xen/qemu-dm-xptest.log > > domid: 1 > qemu: the number of cpus is 2 > Watching /local/domain/0/device-model/1/logdirty/next-active > Watching /local/domain/0/device-model/1/command > qemu_map_cache_init nr_buckets = 10000 size 3145728 > shared page at pfn 1fffe > buffered io page at pfn 1fffc > Time offset set 0 > Register xen platform. > Done register platform. > medium change watch on `hdc'' (index: 1): > I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0 > I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0 > > Which logfiles do I need to post to investigate this problem? > > Andy >_______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Boris Derzhavets
2009-Feb-22 13:48 UTC
[Xen-devel] "xm dmesg" report for the most recent vmlinuz-2.6.29-rc5-tip
__ __ _____ _ _ _ _ _
\ \/ /___ _ __ |___ /| || | _ _ _ __ ___| |_ __ _| |__ | | ___
\ // _ \ \047_ \ |_ \| || |_ __| | | | \047_ \/ __| __/ _` | \047_ \| |/ _
\
/ \ __/ | | | ___) |__ _|__| |_| | | | \__ \ || (_| | |_) | | __/
/_/\_\___|_| |_| |____(_) |_| \__,_|_| |_|___/\__\__,_|_.__/|_|\___|
(XEN) Xen version 3.4-unstable (root@) (gcc version 4.3.2 (Ubuntu
4.3.2-1ubuntu11) ) Sun Feb 22 08:28:39 EST 2009
(XEN) Latest ChangeSet: Thu Feb 19 11:07:33 2009 +0000 19232:84af3ded5b02
(XEN) Command line: dom0_mem=1024M
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 0 MBR signatures
(XEN) Found 2 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009ec00 (usable)
(XEN) 000000000009ec00 - 00000000000a0000 (reserved)
(XEN) 00000000000e4000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000cff80000 (usable)
(XEN) 00000000cff80000 - 00000000cff8e000 (ACPI data)
(XEN) 00000000cff8e000 - 00000000cffe0000 (ACPI NVS)
(XEN) 00000000cffe0000 - 00000000d0000000 (reserved)
(XEN) 00000000fee00000 - 00000000fee01000 (reserved)
(XEN) 00000000ffe00000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 0000000230000000 (usable)
(XEN) System RAM: 8191MB (8387704kB)
(XEN) ACPI: RSDP 000FBB80, 0014 (r0 ACPIAM)
(XEN) ACPI: RSDT CFF80000, 003C (r1 A_M_I_ OEMRSDT 10000730 MSFT 97)
(XEN) ACPI: FACP CFF80200, 0084 (r2 A_M_I_ OEMFACP 10000730 MSFT 97)
(XEN) ACPI: DSDT CFF805C0, 8E13 (r1 A0840 A0840001 1 INTL 20060113)
(XEN) ACPI: FACS CFF8E000, 0040
(XEN) ACPI: APIC CFF80390, 006C (r1 A_M_I_ OEMAPIC 10000730 MSFT 97)
(XEN) ACPI: MCFG CFF80400, 003C (r1 A_M_I_ OEMMCFG 10000730 MSFT 97)
(XEN) ACPI: OEMB CFF8E040, 0081 (r1 A_M_I_ AMI_OEM 10000730 MSFT 97)
(XEN) ACPI: HPET CFF893E0, 0038 (r1 A_M_I_ OEMHPET 10000730 MSFT 97)
(XEN) ACPI: OSFR CFF89420, 00B0 (r1 A_M_I_ OEMOSFR 10000730 MSFT 97)
(XEN) NUMA turned off
(XEN) Faking a node at 0000000000000000-0000000230000000
(XEN) Domain heap initialised
(XEN) found SMP MP-table at 000ff780
(XEN) DMI 2.4 present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x808
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0]
(XEN) ACPI: wakeup_vec[cff8e00c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
(XEN) Processor #1 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
(XEN) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) ACPI: HPET id: 0xffffffff base: 0xfed00000
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing CPU#0
(XEN) Detected 3005.653 MHz processor.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 0
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: VMX enabled
(XEN) MCE: Intel newly family MC Init
(XEN) Intel machine check reporting enabled on CPU#0.
(XEN) CPU0: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU0 has no CMCI support
(XEN) CPU0: Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz stepping 06
(XEN) Booting processor 1/1 eip 8c000
(XEN) Initializing CPU#1
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 1
(XEN) MCE: Intel newly family MC Init
(XEN) Intel machine check reporting enabled on CPU#1.
(XEN) CPU1: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU1 has no CMCI support
(XEN) CPU1: Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz stepping 06
(XEN) Total of 2 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) checking TSC synchronization across 2 CPUs: passed.
(XEN) Platform timer is 14.318MHz HPET
(XEN) Brought up 2 CPUs
(XEN) microcode.c:73:d32767 microcode: CPU1 resumed
(XEN) I/O virtualisation disabled
(XEN) ACPI sleep modes: S3
(XEN) mcheck_poll: Init_mcheck_timer
(XEN) mcheck_poll: Machine check polling timer started.
(XEN) *** LOADING DOMAIN 0 ***
(XEN) elf_parse_binary: phdr: paddr=0x200000 memsz=0x494000
(XEN) elf_parse_binary: phdr: paddr=0x694000 memsz=0x953d4
(XEN) elf_parse_binary: phdr: paddr=0x72a000 memsz=0x8c8
(XEN) elf_parse_binary: phdr: paddr=0x72c000 memsz=0x88086
(XEN) elf_parse_binary: phdr: paddr=0x7b5000 memsz=0x12560
(XEN) elf_parse_binary: phdr: paddr=0x7c8000 memsz=0x111d20
(XEN) elf_parse_binary: memory: 0x200000 -> 0x8d9d20
(XEN) elf_xen_parse_note: GUEST_OS = "linux"
(XEN) elf_xen_parse_note: GUEST_VERSION = "2.6"
(XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0"
(XEN) elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000
(XEN) elf_xen_parse_note: ENTRY = 0xffffffff80756200
(XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff80209000
(XEN) elf_xen_parse_note: FEATURES =
"!writable_page_tables|pae_pgdir_above_4gb"
(XEN) elf_xen_parse_note: PAE_MODE = "yes"
(XEN) elf_xen_parse_note: LOADER = "generic"
(XEN) elf_xen_parse_note: unknown xen elf note (0xd)
(XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1
(XEN) elf_xen_parse_note: HV_START_LOW = 0xffff800000000000
(XEN) elf_xen_parse_note: PADDR_OFFSET = 0x0
(XEN) elf_xen_addr_calc_check: addresses:
(XEN) virt_base = 0xffffffff80000000
(XEN) elf_paddr_offset = 0x0
(XEN) virt_offset = 0xffffffff80000000
(XEN) virt_kstart = 0xffffffff80200000
(XEN) virt_kend = 0xffffffff808d9d20
(XEN) virt_entry = 0xffffffff80756200
(XEN) p2m_base = 0xffffffffffffffff
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x200000 -> 0x8d9d20
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 0000000210000000->0000000220000000 (196608 pages to be
allocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: ffffffff80200000->ffffffff808d9d20
(XEN) Init. ramdisk: ffffffff808da000->ffffffff8bc37600
(XEN) Phys-Mach map: ffffffff8bc38000->ffffffff8be38000
(XEN) Start info: ffffffff8be38000->ffffffff8be384b4
(XEN) Page tables: ffffffff8be39000->ffffffff8be9c000
(XEN) Boot stack: ffffffff8be9c000->ffffffff8be9d000
(XEN) TOTAL: ffffffff80000000->ffffffff8c000000
(XEN) ENTRY ADDRESS: ffffffff80756200
(XEN) Dom0 has maximum 2 VCPUs
(XEN) elf_load_binary: phdr 0 at 0xffffffff80200000 -> 0xffffffff80694000
(XEN) elf_load_binary: phdr 1 at 0xffffffff80694000 -> 0xffffffff807293d4
(XEN) elf_load_binary: phdr 2 at 0xffffffff8072a000 -> 0xffffffff8072a8c8
(XEN) elf_load_binary: phdr 3 at 0xffffffff8072c000 -> 0xffffffff807b4086
(XEN) elf_load_binary: phdr 4 at 0xffffffff807b5000 -> 0xffffffff807c7560
(XEN) elf_load_binary: phdr 5 at 0xffffffff807c8000 -> 0xffffffff807c8000
(XEN) Scrubbing Free RAM:
.......................................................................done.
(XEN) Xen trace buffers: disabled
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) Xen is relinquishing VGA console.
(XEN) *** Serial input -> DOM0 (type \047CTRL-a\047 three times to switch
input to Xen)
(XEN) Freed 124kB init memory.
(XEN) io_apic.c:2147:
(XEN) ioapic_guest_write: apic=0, pin=2, old_irq=0, new_irq=-1
(XEN) ioapic_guest_write: old_entry=000009f0, new_entry=00010900
(XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ!
(XEN) irq.c:930: dom0: pirq 2 or vector 152 already mapped
(XEN) io_apic.c:2160:
(XEN) ioapic_guest_write: apic=0, pin=16, old_irq=16, new_irq=16
(XEN) ioapic_guest_write: old_entry=0000a9a0, new_entry=0001a9a0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) io_apic.c:2160:
(XEN) ioapic_guest_write: apic=0, pin=17, old_irq=17, new_irq=17
(XEN) ioapic_guest_write: old_entry=0000a9a8, new_entry=0001a9a8
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) io_apic.c:2160:
(XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18
(XEN) ioapic_guest_write: old_entry=0000a9b8, new_entry=0001a9b8
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) io_apic.c:2160:
(XEN) ioapic_guest_write: apic=0, pin=23, old_irq=23, new_irq=23
(XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) io_apic.c:2160:
(XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18
(XEN) ioapic_guest_write: old_entry=0000a9b8, new_entry=0001a9b8
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) io_apic.c:2160:
(XEN) ioapic_guest_write: apic=0, pin=16, old_irq=16, new_irq=16
(XEN) ioapic_guest_write: old_entry=0000a9a0, new_entry=0001a9a0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) io_apic.c:2160:
(XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19
(XEN) ioapic_guest_write: old_entry=0000a9d0, new_entry=0001a9d0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) io_apic.c:2160:
(XEN) ioapic_guest_write: apic=0, pin=22, old_irq=22, new_irq=22
(XEN) ioapic_guest_write: old_entry=0000a9b0, new_entry=0001a9b0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
On Sat, Feb 21, 2009 at 3:53 PM, Jeremy Fitzhardinge <jeremy@goop.org> wrote:> Andrew Lyon wrote: >> >> I''ve also tried using 3.3.1 with the backported patches as above, I >> still get a device model failure error but this time there is no >> mention of power management: >> >> [2009-02-21 12:32:33 3486] WARNING (image:472) domain xptest: device >> model failure: pid 3766: malfunctioning (closed sentinel), killed; see >> /var/log/xen/qemu-dm-xptest.log >> > > IanJ would have more of an idea about this stuff than me.I''ve now tried Xen 3.3.1 and 3.3.2 both with the backported patches from xen-unstable for pv_ops dom0 support, and I''ve also tried Xen 3.4 with the fix applied for "pci device without power management", with all 3 a existing VM which works under a non pv_ops Xen kernel fails to start under pv_ops kernel, I''ve also tried different disk backends (tap:io, file:/) the error is always the same: [2009-02-22 14:07:25 3467] WARNING (image:470) domain xptest: device model failure: pid 4224: malfunctioning (closed sentinel), killed; see /var/log/xen/qemu-dm-xptest.log cat /var/log/xen/qemu-dm-xptest.log domid: 4 qemu: the number of cpus is 1 Using xvda for guest''s hda Strip off blktap sub-type prefix to /root/xp (drv ''aio'') Watching /local/domain/0/device-model/4/logdirty/next-active Watching /local/domain/0/device-model/4/command qemu_map_cache_init nr_buckets = 10000 size 3145728 shared page at pfn 1fffe buffered io page at pfn 1fffc Time offset set 0 Register xen platform. Done register platform. I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0 Andy> > J > >> >> cat /var/log/xen/qemu-dm-xptest.log >> >> domid: 1 >> qemu: the number of cpus is 2 >> Watching /local/domain/0/device-model/1/logdirty/next-active >> Watching /local/domain/0/device-model/1/command >> qemu_map_cache_init nr_buckets = 10000 size 3145728 >> shared page at pfn 1fffe >> buffered io page at pfn 1fffc >> Time offset set 0 >> Register xen platform. >> Done register platform. >> medium change watch on `hdc'' (index: 1): >> I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0 >> I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0 >> >> Which logfiles do I need to post to investigate this problem? >> >> Andy >> > >_______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
> I''ve also tried Xen 3.4 with the fix applied > for "pci device without power management"Is it possible to share "How to apply this patch" ? Boris. --- On Sun, 2/22/09, Andrew Lyon <andrew.lyon@gmail.com> wrote: From: Andrew Lyon <andrew.lyon@gmail.com> Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip To: Ian.Jackson@eu.citrix.com, "xen-devel@lists.xensource.com" <xen-devel@lists.xensource.com> Cc: "Jeremy Fitzhardinge" <jeremy@goop.org> Date: Sunday, February 22, 2009, 9:20 AM On Sat, Feb 21, 2009 at 3:53 PM, Jeremy Fitzhardinge <jeremy@goop.org> wrote:> Andrew Lyon wrote: >> >> I''ve also tried using 3.3.1 with the backported patches as above,I>> still get a device model failure error but this time there is no >> mention of power management: >> >> [2009-02-21 12:32:33 3486] WARNING (image:472) domain xptest: device >> model failure: pid 3766: malfunctioning (closed sentinel), killed; see >> /var/log/xen/qemu-dm-xptest.log >> > > IanJ would have more of an idea about this stuff than me.I''ve now tried Xen 3.3.1 and 3.3.2 both with the backported patches from xen-unstable for pv_ops dom0 support, and I''ve also tried Xen 3.4 with the fix applied for "pci device without power management", with all 3 a existing VM which works under a non pv_ops Xen kernel fails to start under pv_ops kernel, I''ve also tried different disk backends (tap:io, file:/) the error is always the same: [2009-02-22 14:07:25 3467] WARNING (image:470) domain xptest: device model failure: pid 4224: malfunctioning (closed sentinel), killed; see /var/log/xen/qemu-dm-xptest.log cat /var/log/xen/qemu-dm-xptest.log domid: 4 qemu: the number of cpus is 1 Using xvda for guest''s hda Strip off blktap sub-type prefix to /root/xp (drv ''aio'') Watching /local/domain/0/device-model/4/logdirty/next-active Watching /local/domain/0/device-model/4/command qemu_map_cache_init nr_buckets = 10000 size 3145728 shared page at pfn 1fffe buffered io page at pfn 1fffc Time offset set 0 Register xen platform. Done register platform. I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0 Andy> > J > >> >> cat /var/log/xen/qemu-dm-xptest.log >> >> domid: 1 >> qemu: the number of cpus is 2 >> Watching /local/domain/0/device-model/1/logdirty/next-active >> Watching /local/domain/0/device-model/1/command >> qemu_map_cache_init nr_buckets = 10000 size 3145728 >> shared page at pfn 1fffe >> buffered io page at pfn 1fffc >> Time offset set 0 >> Register xen platform. >> Done register platform. >> medium change watch on `hdc'' (index: 1): >> I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0 >> I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0 >> >> Which logfiles do I need to post to investigate this problem? >> >> Andy >> > >_______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
On Sun, Feb 22, 2009 at 3:10 PM, Boris Derzhavets <bderzhavets@yahoo.com> wrote:>> I''ve also tried Xen 3.4 with the fix applied >> for "pci device without power management" > Is it possible to share "How to apply this patch" ?Because the ioemu-remote sources do not exist until the build process downloads them I had to use a very crude method, I started the Xen build process and paused it every few seconds using ctrl+z, if tools/ioemu-remote/hw/pass-through.c exists I applied the patch, if not I resumed the process using "fg <enter>", after a while its easy to spot when the code is downloaded. The patch was posed to the mailing list with subject "[Xen-devel] [PATCH] ioemu: Fix the segmentation fault on assigning device without PM cap.", I copied the patch content into a text file and applied with patch -p1 -i <patchfile> But even with the patch applied qemu-dm crashes and the VM does not start. Andy> > Boris. > > > --- On Sun, 2/22/09, Andrew Lyon <andrew.lyon@gmail.com> wrote: > > From: Andrew Lyon <andrew.lyon@gmail.com> > Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip > To: Ian.Jackson@eu.citrix.com, "xen-devel@lists.xensource.com" > <xen-devel@lists.xensource.com> > Cc: "Jeremy Fitzhardinge" <jeremy@goop.org> > Date: Sunday, February 22, 2009, 9:20 AM > > On Sat, Feb 21, 2009 at 3:53 PM, Jeremy Fitzhardinge <jeremy@goop.org> > wrote: >> Andrew Lyon wrote: >>> >>> I''ve also tried using 3.3.1 with the > backported patches as above, > I >>> still get a device model failure error but this time there is no >>> mention of power management: >>> >>> [2009-02-21 12:32:33 3486] WARNING (image:472) domain xptest: device >>> model failure: pid 3766: malfunctioning (closed sentinel), killed; see >>> /var/log/xen/qemu-dm-xptest.log >>> >> >> IanJ would have more of an idea about this stuff than me. > > I''ve now tried Xen 3.3.1 and 3.3.2 both with the backported patches > from xen-unstable for pv_ops dom0 support, and I''ve also tried Xen 3.4 > with the fix applied for "pci device without power management", with > all 3 a existing VM which works under a non pv_ops Xen kernel fails to > start under pv_ops kernel, I''ve also tried different disk backends > (tap:io, file:/) the error is always the same: > > [2009-02-22 14:07:25 3467] WARNING (image:470) domain xptest: device > model failure: > pid 4224: malfunctioning (closed sentinel), killed; see > /var/log/xen/qemu-dm-xptest.log > > > cat /var/log/xen/qemu-dm-xptest.log > domid: 4 > qemu: the number of cpus is 1 > Using xvda for guest''s hda > Strip off blktap sub-type prefix to /root/xp (drv ''aio'') > Watching /local/domain/0/device-model/4/logdirty/next-active > Watching /local/domain/0/device-model/4/command > qemu_map_cache_init nr_buckets = 10000 size 3145728 > shared page at pfn 1fffe > buffered io page at pfn 1fffc > Time offset set 0 > Register xen platform. > Done register platform. > I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0 > > Andy > > >> >> J >> >>> >>> cat /var/log/xen/qemu-dm-xptest.log >>> >>> domid: 1 >>> qemu: the number of cpus is 2 >>> Watching /local/domain/0/device-model/1/logdirty/next-active >>> Watching > /local/domain/0/device-model/1/command >>> qemu_map_cache_init nr_buckets = 10000 size 3145728 >>> shared page at pfn 1fffe >>> buffered io page at pfn 1fffc >>> Time offset set 0 >>> Register xen platform. >>> Done register platform. >>> medium change watch on `hdc'' (index: 1): >>> I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0 >>> I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0 >>> >>> Which logfiles do I need to post to investigate this problem? >>> >>> Andy >>> >> >> > > _______________________________________________ > Xen-devel mailing list > Xen-devel@lists.xensource.com > http://lists.xensource.com/xen-devel > >_______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Jeremy Fitzhardinge
2009-Feb-22 17:12 UTC
[Xen-devel] Re: "xm dmesg" report for the most recent vmlinuz-2.6.29-rc5-tip
Boris Derzhavets wrote:> > __ __ _____ _ _ _ _ _ > \ \/ /___ _ __ |___ /| || | _ _ _ __ ___| |_ __ _| |__ | | ___ > \ // _ \ \047_ \ |_ \| || |_ __| | | | \047_ \/ __| __/ _` | > \047_ \| |/ _ \ > / \ __/ | | | ___) |__ _|__| |_| | | | \__ \ || (_| | |_) | | __/ > /_/\_\___|_| |_| |____(_) |_| \__,_|_| |_|___/\__\__,_|_.__/|_|\___| > > (XEN) Xen version 3.4-unstable (root@) (gcc version 4.3.2 (Ubuntu > 4.3.2-1ubuntu11) ) Sun Feb 22 08:28:39 EST 2009 > (XEN) Latest ChangeSet: Thu Feb 19 11:07:33 2009 +0000 19232:84af3ded5b02 > (XEN) Command line: dom0_mem=1024M > (XEN) Video information: > (XEN) VGA is text mode 80x25, font 8x16 > (XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds > (XEN) EDID info not retrieved because no DDC retrieval method detected > (XEN) Disc information: > (XEN) Found 0 MBR signatures > (XEN) Found 2 EDD information structures > (XEN) Xen-e820 RAM map: > (XEN) 0000000000000000 - 000000000009ec00 (usable) > (XEN) 000000000009ec00 - 00000000000a0000 (reserved) > (XEN) 00000000000e4000 - 0000000000100000 (reserved) > (XEN) 0000000000100000 - 00000000cff80000 (usable) > (XEN) 00000000cff80000 - 00000000cff8e000 (ACPI data) > (XEN) 00000000cff8e000 - 00000000cffe0000 (ACPI NVS) > (XEN) 00000000cffe0000 - 00000000d0000000 (reserved) > (XEN) 00000000fee00000 - 00000000fee01000 (reserved) > (XEN) 00000000ffe00000 - 0000000100000000 (reserved) > (XEN) 0000000100000000 - 0000000230000000 (usable) > (XEN) System RAM: 8191MB (8387704kB) > (XEN) ACPI: RSDP 000FBB80, 0014 (r0 ACPIAM) > (XEN) ACPI: RSDT CFF80000, 003C (r1 A_M_I_ OEMRSDT 10000730 > MSFT 97) > (XEN) ACPI: FACP CFF80200, 0084 (r2 A_M_I_ OEMFACP 10000730 > MSFT 97) > (XEN) ACPI: DSDT CFF805C0, 8E13 (r1 A0840 A0840001 1 INTL > 20060113) > (XEN) ACPI: FACS CFF8E000, 0040 > (XEN) ACPI: APIC CFF80390, 006C (r1 A_M_I_ OEMAPIC 10000730 > MSFT 97) > (XEN) ACPI: MCFG CFF80400, 003C (r1 A_M_I_ OEMMCFG 10000730 > MSFT 97) > (XEN) ACPI: OEMB CFF8E040, 0081 (r1 A_M_I_ AMI_OEM 10000730 > MSFT 97) > (XEN) ACPI: HPET CFF893E0, 0038 (r1 A_M_I_ OEMHPET 10000730 > MSFT 97) > (XEN) ACPI: OSFR CFF89420, 00B0 (r1 A_M_I_ OEMOSFR 10000730 > MSFT 97) > (XEN) NUMA turned off > (XEN) Faking a node at 0000000000000000-0000000230000000 > (XEN) Domain heap initialised > (XEN) found SMP MP-table at 000ff780 > (XEN) DMI 2.4 present. > (XEN) Using APIC driver default > (XEN) ACPI: PM-Timer IO Port: 0x808 > (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0] > (XEN) ACPI: wakeup_vec[cff8e00c], vec_size[20] > (XEN) ACPI: Local APIC address 0xfee00000 > (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > (XEN) Processor #0 7:7 APIC version 20 > (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) > (XEN) Processor #1 7:7 APIC version 20 > (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) > (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) > (XEN) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) > (XEN) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) > (XEN) ACPI: IRQ0 used by override. > (XEN) ACPI: IRQ2 used by override. > (XEN) ACPI: IRQ9 used by override. > (XEN) Enabling APIC mode: Flat. Using 1 I/O APICs > (XEN) ACPI: HPET id: 0xffffffff base: 0xfed00000 > (XEN) Using ACPI (MADT) for SMP configuration information > (XEN) Using scheduler: SMP Credit Scheduler (credit) > (XEN) Initializing CPU#0 > (XEN) Detected 3005.653 MHz processor. > (XEN) CPU: L1 I cache: 32K, L1 D cache: 32K > (XEN) CPU: L2 cache: 6144K > (XEN) CPU: Physical Processor ID: 0 > (XEN) CPU: Processor Core ID: 0 > (XEN) VMX: Supported advanced features: > (XEN) - APIC MMIO access virtualisation > (XEN) - APIC TPR shadow > (XEN) - Virtual NMI > (XEN) - MSR direct-access bitmap > (XEN) HVM: VMX enabled > (XEN) MCE: Intel newly family MC Init > (XEN) Intel machine check reporting enabled on CPU#0. > (XEN) CPU0: Thermal monitoring enabled (TM2) > (XEN) CMCI: CPU0 has no CMCI support > (XEN) CPU0: Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz stepping 06 > (XEN) Booting processor 1/1 eip 8c000 > (XEN) Initializing CPU#1 > (XEN) CPU: L1 I cache: 32K, L1 D cache: 32K > (XEN) CPU: L2 cache: 6144K > (XEN) CPU: Physical Processor ID: 0 > (XEN) CPU: Processor Core ID: 1 > (XEN) MCE: Intel newly family MC Init > (XEN) Intel machine check reporting enabled on CPU#1. > (XEN) CPU1: Thermal monitoring enabled (TM2) > (XEN) CMCI: CPU1 has no CMCI support > (XEN) CPU1: Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz stepping 06 > (XEN) Total of 2 processors activated. > (XEN) ENABLING IO-APIC IRQs > (XEN) -> Using new ACK method > (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1 > (XEN) checking TSC synchronization across 2 CPUs: passed. > (XEN) Platform timer is 14.318MHz HPET > (XEN) Brought up 2 CPUs > (XEN) microcode.c:73:d32767 microcode: CPU1 resumed > (XEN) I/O virtualisation disabled > (XEN) ACPI sleep modes: S3 > (XEN) mcheck_poll: Init_mcheck_timer > (XEN) mcheck_poll: Machine check polling timer started. > (XEN) *** LOADING DOMAIN 0 *** > (XEN) elf_parse_binary: phdr: paddr=0x200000 memsz=0x494000 > (XEN) elf_parse_binary: phdr: paddr=0x694000 memsz=0x953d4 > (XEN) elf_parse_binary: phdr: paddr=0x72a000 memsz=0x8c8 > (XEN) elf_parse_binary: phdr: paddr=0x72c000 memsz=0x88086 > (XEN) elf_parse_binary: phdr: paddr=0x7b5000 memsz=0x12560 > (XEN) elf_parse_binary: phdr: paddr=0x7c8000 memsz=0x111d20 > (XEN) elf_parse_binary: memory: 0x200000 -> 0x8d9d20 > (XEN) elf_xen_parse_note: GUEST_OS = "linux" > (XEN) elf_xen_parse_note: GUEST_VERSION = "2.6" > (XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0" > (XEN) elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000 > (XEN) elf_xen_parse_note: ENTRY = 0xffffffff80756200 > (XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff80209000 > (XEN) elf_xen_parse_note: FEATURES = > "!writable_page_tables|pae_pgdir_above_4gb" > (XEN) elf_xen_parse_note: PAE_MODE = "yes" > (XEN) elf_xen_parse_note: LOADER = "generic" > (XEN) elf_xen_parse_note: unknown xen elf note (0xd) > (XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1 > (XEN) elf_xen_parse_note: HV_START_LOW = 0xffff800000000000 > (XEN) elf_xen_parse_note: PADDR_OFFSET = 0x0 > (XEN) elf_xen_addr_calc_check: addresses: > (XEN) virt_base = 0xffffffff80000000 > (XEN) elf_paddr_offset = 0x0 > (XEN) virt_offset = 0xffffffff80000000 > (XEN) virt_kstart = 0xffffffff80200000 > (XEN) virt_kend = 0xffffffff808d9d20 > (XEN) virt_entry = 0xffffffff80756200 > (XEN) p2m_base = 0xffffffffffffffff > (XEN) Xen kernel: 64-bit, lsb, compat32 > (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x200000 -> 0x8d9d20 > (XEN) PHYSICAL MEMORY ARRANGEMENT: > (XEN) Dom0 alloc.: 0000000210000000->0000000220000000 (196608 pages > to be allocated) > (XEN) VIRTUAL MEMORY ARRANGEMENT: > (XEN) Loaded kernel: ffffffff80200000->ffffffff808d9d20 > (XEN) Init. ramdisk: ffffffff808da000->ffffffff8bc37600 > (XEN) Phys-Mach map: ffffffff8bc38000->ffffffff8be38000 > (XEN) Start info: ffffffff8be38000->ffffffff8be384b4 > (XEN) Page tables: ffffffff8be39000->ffffffff8be9c000 > (XEN) Boot stack: ffffffff8be9c000->ffffffff8be9d000 > (XEN) TOTAL: ffffffff80000000->ffffffff8c000000 > (XEN) ENTRY ADDRESS: ffffffff80756200 > (XEN) Dom0 has maximum 2 VCPUs > (XEN) elf_load_binary: phdr 0 at 0xffffffff80200000 -> 0xffffffff80694000 > (XEN) elf_load_binary: phdr 1 at 0xffffffff80694000 -> 0xffffffff807293d4 > (XEN) elf_load_binary: phdr 2 at 0xffffffff8072a000 -> 0xffffffff8072a8c8 > (XEN) elf_load_binary: phdr 3 at 0xffffffff8072c000 -> 0xffffffff807b4086 > (XEN) elf_load_binary: phdr 4 at 0xffffffff807b5000 -> 0xffffffff807c7560 > (XEN) elf_load_binary: phdr 5 at 0xffffffff807c8000 -> 0xffffffff807c8000 > (XEN) Scrubbing Free RAM: > .......................................................................done. > (XEN) Xen trace buffers: disabled > (XEN) Std. Loglevel: All > (XEN) Guest Loglevel: All > (XEN) Xen is relinquishing VGA console. > (XEN) *** Serial input -> DOM0 (type \047CTRL-a\047 three times to > switch input to Xen) > (XEN) Freed 124kB init memory. > (XEN) io_apic.c:2147: > (XEN) ioapic_guest_write: apic=0, pin=2, old_irq=0, new_irq=-1 > (XEN) ioapic_guest_write: old_entry=000009f0, new_entry=00010900 > (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ! > (XEN) irq.c:930: dom0: pirq 2 or vector 152 already mapped > (XEN) io_apic.c:2160: > (XEN) ioapic_guest_write: apic=0, pin=16, old_irq=16, new_irq=16 > (XEN) ioapic_guest_write: old_entry=0000a9a0, new_entry=0001a9a0 > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! > (XEN) io_apic.c:2160: > (XEN) ioapic_guest_write: apic=0, pin=17, old_irq=17, new_irq=17 > (XEN) ioapic_guest_write: old_entry=0000a9a8, new_entry=0001a9a8 > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! > (XEN) io_apic.c:2160: > (XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18 > (XEN) ioapic_guest_write: old_entry=0000a9b8, new_entry=0001a9b8 > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! > (XEN) io_apic.c:2160: > (XEN) ioapic_guest_write: apic=0, pin=23, old_irq=23, new_irq=23 > (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0 > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! > (XEN) io_apic.c:2160: > (XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18 > (XEN) ioapic_guest_write: old_entry=0000a9b8, new_entry=0001a9b8 > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! > (XEN) io_apic.c:2160: > (XEN) ioapic_guest_write: apic=0, pin=16, old_irq=16, new_irq=16 > (XEN) ioapic_guest_write: old_entry=0000a9a0, new_entry=0001a9a0 > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! > (XEN) io_apic.c:2160: > (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19 > (XEN) ioapic_guest_write: old_entry=0000a9d0, new_entry=0001a9d0 > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! > (XEN) io_apic.c:2160: > (XEN) ioapic_guest_write: apic=0, pin=22, old_irq=22, new_irq=22 > (XEN) ioapic_guest_write: old_entry=0000a9b0, new_entry=0001a9b0 > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! > >Yes, I''ve started seeing this too; it looks like something''s trying to mask the ioapic pins, but I''m not sure what changed. It doesn''t seem to have any bad effects on my machine. Does anything actually malfunction for you? J _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Thank you for explanation, i would try a script (pseudo code) Check for pid of download process after start. Modify script kind of bellow afterwards and start monitor in another terminal window PID_DOWNLOAD = XXXX while [ 1 == 1] do var=`file /usr/src/xen-unstable.hg/tools/ioemu-remote/hw/pass-through.c` if [ $? == 0 ] ; then kill -SIGSTOP $PID_DOWNLOAD exit 1 fi sleep 3 done --- On Sun, 2/22/09, Andrew Lyon <andrew.lyon@gmail.com> wrote: From: Andrew Lyon <andrew.lyon@gmail.com> Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip To: bderzhavets@yahoo.com Cc: Ian.Jackson@eu.citrix.com, "xen-devel@lists.xensource.com" <xen-devel@lists.xensource.com>, "Jeremy Fitzhardinge" <jeremy@goop.org> Date: Sunday, February 22, 2009, 10:19 AM On Sun, Feb 22, 2009 at 3:10 PM, Boris Derzhavets <bderzhavets@yahoo.com> wrote:>> I''ve also tried Xen 3.4 with the fix applied >> for "pci device without power management" > Is it possible to share "How to apply this patch" ?Because the ioemu-remote sources do not exist until the build process downloads them I had to use a very crude method, I started the Xen build process and paused it every few seconds using ctrl+z, if tools/ioemu-remote/hw/pass-through.c exists I applied the patch, if not I resumed the process using "fg <enter>", after a while its easy to spot when the code is downloaded. The patch was posed to the mailing list with subject "[Xen-devel] [PATCH] ioemu: Fix the segmentation fault on assigning device without PM cap.", I copied the patch content into a text file and applied with patch -p1 -i <patchfile> But even with the patch applied qemu-dm crashes and the VM does not start. Andy> > Boris. > > > --- On Sun, 2/22/09, Andrew Lyon <andrew.lyon@gmail.com> wrote: > > From: Andrew Lyon <andrew.lyon@gmail.com> > Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip > To: Ian.Jackson@eu.citrix.com, "xen-devel@lists.xensource.com" > <xen-devel@lists.xensource.com> > Cc: "Jeremy Fitzhardinge" <jeremy@goop.org> > Date: Sunday, February 22, 2009, 9:20 AM > > On Sat, Feb 21, 2009 at 3:53 PM, Jeremy Fitzhardinge<jeremy@goop.org>> wrote: >> Andrew Lyon wrote: >>> >>> I''ve also tried using 3.3.1 with the > backported patches as above, > I >>> still get a device model failure error but this time there is no >>> mention of power management: >>> >>> [2009-02-21 12:32:33 3486] WARNING (image:472) domain xptest:device>>> model failure: pid 3766: malfunctioning (closed sentinel), killed;see>>> /var/log/xen/qemu-dm-xptest.log >>> >> >> IanJ would have more of an idea about this stuff than me. > > I''ve now tried Xen 3.3.1 and 3.3.2 both with the backported patches > from xen-unstable for pv_ops dom0 support, and I''ve also tried Xen 3.4 > with the fix applied for "pci device without power management",with> all 3 a existing VM which works under a non pv_ops Xen kernel fails to > start under pv_ops kernel, I''ve also tried different disk backends > (tap:io, file:/) the error is always the same: > > [2009-02-22 14:07:25 3467] WARNING (image:470) domain xptest: device > model failure: > pid 4224: malfunctioning (closed sentinel), killed; see > /var/log/xen/qemu-dm-xptest.log > > > cat /var/log/xen/qemu-dm-xptest.log > domid: 4 > qemu: the number of cpus is 1 > Using xvda for guest''s hda > Strip off blktap sub-type prefix to /root/xp (drv ''aio'') > Watching /local/domain/0/device-model/4/logdirty/next-active > Watching /local/domain/0/device-model/4/command > qemu_map_cache_init nr_buckets = 10000 size 3145728 > shared page at pfn 1fffe > buffered io page at pfn 1fffc > Time offset set 0 > Register xen platform. > Done register platform. > I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0 > > Andy > > >> >> J >> >>> >>> cat /var/log/xen/qemu-dm-xptest.log >>> >>> domid: 1 >>> qemu: the number of cpus is 2 >>> Watching /local/domain/0/device-model/1/logdirty/next-active >>> Watching > /local/domain/0/device-model/1/command >>> qemu_map_cache_init nr_buckets = 10000 size 3145728 >>> shared page at pfn 1fffe >>> buffered io page at pfn 1fffc >>> Time offset set 0 >>> Register xen platform. >>> Done register platform. >>> medium change watch on `hdc'' (index: 1): >>> I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0,size: 0>>> I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0,size: 0>>> >>> Which logfiles do I need to post to investigate this problem? >>> >>> Andy >>> >> >> > > _______________________________________________ > Xen-devel mailing list > Xen-devel@lists.xensource.com > http://lists.xensource.com/xen-devel > >_______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Boris Derzhavets
2009-Feb-22 17:27 UTC
[Xen-devel] Re: "xm dmesg" report for the most recent vmlinuz-2.6.29-rc5-tip
No. I have F10 and Solaris Nevada (b106) PV DomUs reinstalled under 2.6.29-rc5 ( with APIC issue fixed ) . "yum update" performed 730 MB download at F10 DomU and i setup VNC on F10 PV DomU with Nautilus alive. Unfortunately, we can''t test HVM DomUs due to known issues. --- On Sun, 2/22/09, Jeremy Fitzhardinge <jeremy@goop.org> wrote: From: Jeremy Fitzhardinge <jeremy@goop.org> Subject: Re: "xm dmesg" report for the most recent vmlinuz-2.6.29-rc5-tip To: bderzhavets@yahoo.com Cc: "xen-devel@lists.xensource.com" <xen-devel@lists.xensource.com> Date: Sunday, February 22, 2009, 12:12 PM Boris Derzhavets wrote:> > __ __ _____ _ _ _ _ _\ \/ /___ _ __ |___ /| || | _ _ _ __ ___| |_ __ _| |__ | | ___> \ // _ \ \047_ \ |_ \| || |_ __| | | | \047_\/ __| __/ _` | \047_ \| |/ _ \> / \ __/ | | | ___) |__ _|__| |_| | | | \__ \ || (_| ||_) | | __/> /_/\_\___|_| |_| |____(_) |_| \__,_|_||_|___/\__\__,_|_.__/|_|\___|>(XEN) Xen version 3.4-unstable (root@) (gcc version 4.3.2 (Ubuntu 4.3.2-1ubuntu11) ) Sun Feb 22 08:28:39 EST 2009> (XEN) Latest ChangeSet: Thu Feb 19 11:07:33 2009 +0000 19232:84af3ded5b02 > (XEN) Command line: dom0_mem=1024M > (XEN) Video information: > (XEN) VGA is text mode 80x25, font 8x16 > (XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds > (XEN) EDID info not retrieved because no DDC retrieval method detected > (XEN) Disc information: > (XEN) Found 0 MBR signatures > (XEN) Found 2 EDD information structures > (XEN) Xen-e820 RAM map: > (XEN) 0000000000000000 - 000000000009ec00 (usable) > (XEN) 000000000009ec00 - 00000000000a0000 (reserved) > (XEN) 00000000000e4000 - 0000000000100000 (reserved) > (XEN) 0000000000100000 - 00000000cff80000 (usable) > (XEN) 00000000cff80000 - 00000000cff8e000 (ACPI data) > (XEN) 00000000cff8e000 - 00000000cffe0000 (ACPI NVS) > (XEN) 00000000cffe0000 - 00000000d0000000 (reserved) > (XEN) 00000000fee00000 - 00000000fee01000 (reserved) > (XEN) 00000000ffe00000 - 0000000100000000 (reserved) > (XEN) 0000000100000000 - 0000000230000000 (usable) > (XEN) System RAM: 8191MB (8387704kB) > (XEN) ACPI: RSDP 000FBB80, 0014 (r0 ACPIAM) > (XEN) ACPI: RSDT CFF80000, 003C (r1 A_M_I_ OEMRSDT 10000730 MSFT97)> (XEN) ACPI: FACP CFF80200, 0084 (r2 A_M_I_ OEMFACP 10000730 MSFT97)> (XEN) ACPI: DSDT CFF805C0, 8E13 (r1 A0840 A0840001 1 INTL20060113)> (XEN) ACPI: FACS CFF8E000, 0040 > (XEN) ACPI: APIC CFF80390, 006C (r1 A_M_I_ OEMAPIC 10000730 MSFT97)> (XEN) ACPI: MCFG CFF80400, 003C (r1 A_M_I_ OEMMCFG 10000730 MSFT97)> (XEN) ACPI: OEMB CFF8E040, 0081 (r1 A_M_I_ AMI_OEM 10000730 MSFT97)> (XEN) ACPI: HPET CFF893E0, 0038 (r1 A_M_I_ OEMHPET 10000730 MSFT97)> (XEN) ACPI: OSFR CFF89420, 00B0 (r1 A_M_I_ OEMOSFR 10000730 MSFT97)> (XEN) NUMA turned off > (XEN) Faking a node at 0000000000000000-0000000230000000 > (XEN) Domain heap initialised > (XEN) found SMP MP-table at 000ff780 > (XEN) DMI 2.4 present. > (XEN) Using APIC driver default > (XEN) ACPI: PM-Timer IO Port: 0x808 > (XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[804,0], pm1x_evt[800,0] > (XEN) ACPI: wakeup_vec[cff8e00c], vec_size[20] > (XEN) ACPI: Local APIC address 0xfee00000 > (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > (XEN) Processor #0 7:7 APIC version 20 > (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) > (XEN) Processor #1 7:7 APIC version 20 > (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) > (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) > (XEN) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) > (XEN) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) > (XEN) ACPI: IRQ0 used by override. > (XEN) ACPI: IRQ2 used by override. > (XEN) ACPI: IRQ9 used by override. > (XEN) Enabling APIC mode: Flat. Using 1 I/O APICs > (XEN) ACPI: HPET id: 0xffffffff base: 0xfed00000 > (XEN) Using ACPI (MADT) for SMP configuration information > (XEN) Using scheduler: SMP Credit Scheduler (credit) > (XEN) Initializing CPU#0 > (XEN) Detected 3005.653 MHz processor. > (XEN) CPU: L1 I cache: 32K, L1 D cache: 32K > (XEN) CPU: L2 cache: 6144K > (XEN) CPU: Physical Processor ID: 0 > (XEN) CPU: Processor Core ID: 0 > (XEN) VMX: Supported advanced features: > (XEN) - APIC MMIO access virtualisation > (XEN) - APIC TPR shadow > (XEN) - Virtual NMI > (XEN) - MSR direct-access bitmap > (XEN) HVM: VMX enabled > (XEN) MCE: Intel newly family MC Init > (XEN) Intel machine check reporting enabled on CPU#0. > (XEN) CPU0: Thermal monitoring enabled (TM2) > (XEN) CMCI: CPU0 has no CMCI support > (XEN) CPU0: Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz stepping 06 > (XEN) Booting processor 1/1 eip 8c000 > (XEN) Initializing CPU#1 > (XEN) CPU: L1 I cache: 32K, L1 D cache: 32K > (XEN) CPU: L2 cache: 6144K > (XEN) CPU: Physical Processor ID: 0 > (XEN) CPU: Processor Core ID: 1 > (XEN) MCE: Intel newly family MC Init > (XEN) Intel machine check reporting enabled on CPU#1. > (XEN) CPU1: Thermal monitoring enabled (TM2) > (XEN) CMCI: CPU1 has no CMCI support > (XEN) CPU1: Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz stepping 06 > (XEN) Total of 2 processors activated. > (XEN) ENABLING IO-APIC IRQs > (XEN) -> Using new ACK method > (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1 > (XEN) checking TSC synchronization across 2 CPUs: passed. > (XEN) Platform timer is 14.318MHz HPET > (XEN) Brought up 2 CPUs > (XEN) microcode.c:73:d32767 microcode: CPU1 resumed > (XEN) I/O virtualisation disabled > (XEN) ACPI sleep modes: S3 > (XEN) mcheck_poll: Init_mcheck_timer > (XEN) mcheck_poll: Machine check polling timer started. > (XEN) *** LOADING DOMAIN 0 *** > (XEN) elf_parse_binary: phdr: paddr=0x200000 memsz=0x494000 > (XEN) elf_parse_binary: phdr: paddr=0x694000 memsz=0x953d4 > (XEN) elf_parse_binary: phdr: paddr=0x72a000 memsz=0x8c8 > (XEN) elf_parse_binary: phdr: paddr=0x72c000 memsz=0x88086 > (XEN) elf_parse_binary: phdr: paddr=0x7b5000 memsz=0x12560 > (XEN) elf_parse_binary: phdr: paddr=0x7c8000 memsz=0x111d20 > (XEN) elf_parse_binary: memory: 0x200000 -> 0x8d9d20 > (XEN) elf_xen_parse_note: GUEST_OS = "linux" > (XEN) elf_xen_parse_note: GUEST_VERSION = "2.6" > (XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0" > (XEN) elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000 > (XEN) elf_xen_parse_note: ENTRY = 0xffffffff80756200 > (XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff80209000 > (XEN) elf_xen_parse_note: FEATURES "!writable_page_tables|pae_pgdir_above_4gb" > (XEN) elf_xen_parse_note: PAE_MODE = "yes" > (XEN) elf_xen_parse_note: LOADER = "generic" > (XEN) elf_xen_parse_note: unknown xen elf note (0xd) > (XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1 > (XEN) elf_xen_parse_note: HV_START_LOW = 0xffff800000000000 > (XEN) elf_xen_parse_note: PADDR_OFFSET = 0x0 > (XEN) elf_xen_addr_calc_check: addresses: > (XEN) virt_base = 0xffffffff80000000 > (XEN) elf_paddr_offset = 0x0 > (XEN) virt_offset = 0xffffffff80000000 > (XEN) virt_kstart = 0xffffffff80200000 > (XEN) virt_kend = 0xffffffff808d9d20 > (XEN) virt_entry = 0xffffffff80756200 > (XEN) p2m_base = 0xffffffffffffffff > (XEN) Xen kernel: 64-bit, lsb, compat32 > (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x200000 -> 0x8d9d20 > (XEN) PHYSICAL MEMORY ARRANGEMENT: > (XEN) Dom0 alloc.: 0000000210000000->0000000220000000 (196608 pagesto be allocated)> (XEN) VIRTUAL MEMORY ARRANGEMENT: > (XEN) Loaded kernel: ffffffff80200000->ffffffff808d9d20 > (XEN) Init. ramdisk: ffffffff808da000->ffffffff8bc37600 > (XEN) Phys-Mach map: ffffffff8bc38000->ffffffff8be38000 > (XEN) Start info: ffffffff8be38000->ffffffff8be384b4 > (XEN) Page tables: ffffffff8be39000->ffffffff8be9c000 > (XEN) Boot stack: ffffffff8be9c000->ffffffff8be9d000 > (XEN) TOTAL: ffffffff80000000->ffffffff8c000000 > (XEN) ENTRY ADDRESS: ffffffff80756200 > (XEN) Dom0 has maximum 2 VCPUs > (XEN) elf_load_binary: phdr 0 at 0xffffffff80200000 ->0xffffffff80694000> (XEN) elf_load_binary: phdr 1 at 0xffffffff80694000 ->0xffffffff807293d4> (XEN) elf_load_binary: phdr 2 at 0xffffffff8072a000 ->0xffffffff8072a8c8> (XEN) elf_load_binary: phdr 3 at 0xffffffff8072c000 ->0xffffffff807b4086> (XEN) elf_load_binary: phdr 4 at 0xffffffff807b5000 ->0xffffffff807c7560> (XEN) elf_load_binary: phdr 5 at 0xffffffff807c8000 ->0xffffffff807c8000> (XEN) Scrubbing Free RAM:.......................................................................done.> (XEN) Xen trace buffers: disabled > (XEN) Std. Loglevel: All > (XEN) Guest Loglevel: All > (XEN) Xen is relinquishing VGA console. > (XEN) *** Serial input -> DOM0 (type \047CTRL-a\047 three timesto switch input to Xen)> (XEN) Freed 124kB init memory. > (XEN) io_apic.c:2147: > (XEN) ioapic_guest_write: apic=0, pin=2, old_irq=0, new_irq=-1 > (XEN) ioapic_guest_write: old_entry=000009f0, new_entry=00010900 > (XEN) ioapic_guest_write: Attempt to remove IO-APIC pin of in-use IRQ! > (XEN) irq.c:930: dom0: pirq 2 or vector 152 already mapped > (XEN) io_apic.c:2160: > (XEN) ioapic_guest_write: apic=0, pin=16, old_irq=16, new_irq=16 > (XEN) ioapic_guest_write: old_entry=0000a9a0, new_entry=0001a9a0 > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! > (XEN) io_apic.c:2160: > (XEN) ioapic_guest_write: apic=0, pin=17, old_irq=17, new_irq=17 > (XEN) ioapic_guest_write: old_entry=0000a9a8, new_entry=0001a9a8 > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! > (XEN) io_apic.c:2160: > (XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18 > (XEN) ioapic_guest_write: old_entry=0000a9b8, new_entry=0001a9b8 > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! > (XEN) io_apic.c:2160: > (XEN) ioapic_guest_write: apic=0, pin=23, old_irq=23, new_irq=23 > (XEN) ioapic_guest_write: old_entry=0000a9c0, new_entry=0001a9c0 > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! > (XEN) io_apic.c:2160: > (XEN) ioapic_guest_write: apic=0, pin=18, old_irq=18, new_irq=18 > (XEN) ioapic_guest_write: old_entry=0000a9b8, new_entry=0001a9b8 > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! > (XEN) io_apic.c:2160: > (XEN) ioapic_guest_write: apic=0, pin=16, old_irq=16, new_irq=16 > (XEN) ioapic_guest_write: old_entry=0000a9a0, new_entry=0001a9a0 > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! > (XEN) io_apic.c:2160: > (XEN) ioapic_guest_write: apic=0, pin=19, old_irq=19, new_irq=19 > (XEN) ioapic_guest_write: old_entry=0000a9d0, new_entry=0001a9d0 > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! > (XEN) io_apic.c:2160: > (XEN) ioapic_guest_write: apic=0, pin=22, old_irq=22, new_irq=22 > (XEN) ioapic_guest_write: old_entry=0000a9b0, new_entry=0001a9b0 > (XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ! > >Yes, I''ve started seeing this too; it looks like something''s trying to mask the ioapic pins, but I''m not sure what changed. It doesn''t seem to have any bad effects on my machine. Does anything actually malfunction for you? J _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Andrew Lyon wrote:> what is the correct technique for applying patches to ioemu-remote ? > the source doesn''t exist until the build process is started, is it > possible to manually pull the source and then tell the build process > not to download it? >you can easily clone the qemu-xen repository manually from here: http://xenbits.xensource.com/git-http/qemu-xen-unstable.git apply your patches, then compile it: export XEN_ROOT=/path/to/xen-unstable.hg ./xen-setup make you''ll find the compiled binary under i386-dm _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
I guess # make install-tools won''t pick up binaries from i386-dm and i will have to do something like (?) :- # cd /usr/src/xen-unstable.hg/i386-dm # make install Actually, what command is supposed to install binaries from /usr/src/xen-unstable.hg/i386-dm ? Thanks Boris. --- On Sun, 2/22/09, Stefano Stabellini <stefano.stabellini@eu.citrix.com> wrote: From: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip To: "Andrew Lyon" <andrew.lyon@gmail.com> Cc: "Jeremy Fitzhardinge" <jeremy@goop.org>, "bderzhavets@yahoo.com" <bderzhavets@yahoo.com>, "xen-devel@lists.xensource.com" <xen-devel@lists.xensource.com>, "Marc - A. Dahlhaus [ Administration | Westermann GmbH ]" <mad@wol.de> Date: Sunday, February 22, 2009, 9:39 PM Andrew Lyon wrote:> what is the correct technique for applying patches to ioemu-remote ? > the source doesn''t exist until the build process is started, is it > possible to manually pull the source and then tell the build process > not to download it? >you can easily clone the qemu-xen repository manually from here: http://xenbits.xensource.com/git-http/qemu-xen-unstable.git apply your patches, then compile it: export XEN_ROOT=/path/to/xen-unstable.hg ./xen-setup make you''ll find the compiled binary under i386-dm _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Another guess to recreate symlink ioemu-dir :- cd /usr/src/xen-unstable.hg/tools rm ioemu-dir ln -s /usr/src/xen-unstable.hg/tools/i386-dm ioemu-dir --- On Mon, 2/23/09, Boris Derzhavets <bderzhavets@yahoo.com> wrote: From: Boris Derzhavets <bderzhavets@yahoo.com> Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip To: "Andrew Lyon" <andrew.lyon@gmail.com>, "Stefano Stabellini" <stefano.stabellini@eu.citrix.com> Cc: "Jeremy Fitzhardinge" <jeremy@goop.org>, "xen-devel@lists.xensource.com" <xen-devel@lists.xensource.com>, "Marc - A. Dahlhaus [ Administration | Westermann GmbH ]" <mad@wol.de> Date: Monday, February 23, 2009, 5:19 AM I guess # make install-tools won''t pick up binaries from i386-dm and i will have to do something like (?) :- # cd /usr/src/xen-unstable.hg/i386-dm # make install Actually, what command is supposed to install binaries from /usr/src/xen-unstable.hg/i386-dm ? Thanks Boris. --- On Sun, 2/22/09, Stefano Stabellini <stefano.stabellini@eu.citrix.com> wrote: From: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip To: "Andrew Lyon" <andrew.lyon@gmail.com> Cc: "Jeremy Fitzhardinge" <jeremy@goop.org>, "bderzhavets@yahoo.com" <bderzhavets@yahoo.com>, "xen-devel@lists.xensource.com" <xen-devel@lists.xensource.com>, "Marc - A. Dahlhaus [ Administration | Westermann GmbH ]" <mad@wol.de> Date: Sunday, February 22, 2009, 9:39 PM Andrew Lyon wrote:> what is the correct technique for applying patches to ioemu-remote ? > the source doesn''t exist until the build process is started, is it > possible to manually pull the source and then tell the build process > not to download it? >you can easily clone the qemu-xen repository manually from here: http://xenbits.xensource.com/git-http/qemu-xen-unstable.git apply your patches, then compile it: export XEN_ROOT=/path/to/xen-unstable.hg ./xen-setup make you''ll find the compiled binary under i386-dm _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Andrew Lyon writes ("Re: [Xen-devel] Build
vmlinuz-2.6.29-rc5-tip"):> Because the ioemu-remote sources do not exist until the build process
> downloads them I had to use a very crude method, I started the Xen
> build process and paused it every few seconds using ctrl+z, if
> tools/ioemu-remote/hw/pass-through.c exists I applied the patch, if
> not I resumed the process using "fg <enter>", after a while
its easy
> to spot when the code is downloaded.
This is not necessary. You can easily clone the qemu-xen-unstable
source yourself and get the xen-unstable tree to use that instead;
this is probably the easiest way.
Change to the parent directory of your xen-unstable tree and say
git-clone http://xenbits.xensource.com/git-http/qemu-xen-unstable.git
and then create
xen-unstable.hg/.config
containing
CONFIG_QEMU=/u/iwj/work/qemu-xen-unstable
or whatever the path is.
Ian.
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
Ian Jackson
2009-Feb-23 16:42 UTC
Re: [Xen-devel] Reproduced error when creating Intrepid HVM at Xen Unstable Dom0(vmlinuz-2.6.29-rc5-tip)
Boris Derzhavets writes ("[Xen-devel] Reproduced error when creating
Intrepid HVM at Xen Unstable
Dom0(vmlinuz-2.6.29-rc5-tip)"):> After fresh port Xen Unstable:-
...> xs_read(/local/domain/0/device-model/1/xen_extended_power_mgmt): read error
This emssage is not important.
> "If we assign the device that doesn''t have Power Management
Capability
> Structure to guest domain, qemu accesses NULL pointer."
And this is not relevant to you, unless you are trying to pass through
PCI devices to your HVM guest.
Having said that, Yuji Shimada''s patch should be in staging now and
should be pushed to qemu-xen-unstable very shortly.
Ian.
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
Boris Derzhavets
2009-Feb-23 18:04 UTC
Re: [Xen-devel] Reproduced error when creating Intrepid HVM at Xen Unstable Dom0(vmlinuz-2.6.29-rc5-tip)
--- On Mon, 2/23/09, Ian Jackson <Ian.Jackson@eu.citrix.com> wrote:
From: Ian Jackson <Ian.Jackson@eu.citrix.com>
Subject: Re: [Xen-devel] Reproduced error when creating Intrepid HVM at Xen
Unstable Dom0(vmlinuz-2.6.29-rc5-tip)
To: bderzhavets@yahoo.com
Cc: "xen-devel@lists.xensource.com"
<xen-devel@lists.xensource.com>
Date: Monday, February 23, 2009, 11:42 AM
Boris Derzhavets writes ("[Xen-devel] Reproduced error when creating
Intrepid HVM at Xen Unstable
Dom0(vmlinuz-2.6.29-rc5-tip)"):> After fresh port Xen Unstable:-
...> xs_read(/local/domain/0/device-model/1/xen_extended_power_mgmt): read
error
This emssage is not important.
> "If we assign the device that doesn''t have Power Management
Capability> Structure to guest domain, qemu accesses NULL pointer."
And this is not relevant to you, unless you are trying to pass through
PCI devices to your HVM guest.
************************************************
No, i am not trying to pass through
PCI devices to my HVM guest.
Boris.
************************************************
Having said that, Yuji Shimada''s patch should be in staging now and
should be pushed to qemu-xen-unstable very shortly.
Ian.
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel