Hello, I''m using xen-unstable tarball downloaded 25/08/05 and have two network cards installed on this machine. None of them is working. The /proc/interrupts shows eth0 alone but always with 0 interrupts. I''m attaching xm dmesg and dmesg output, respectively. Xen version 3.0-devel (root@) (gcc version 4.0.1 (4.0.1-2mdk for Mandriva Linux release 2006.0)) Thu Aug 25 10:19:50 EDT 2005 Latest ChangeSet: (XEN) Physical RAM map: (XEN) 0000000000000000 - 00000000000a0000 (usable) (XEN) 00000000000f0000 - 0000000000100000 (reserved) (XEN) 0000000000100000 - 000000000f7f0000 (usable) (XEN) 000000000f7f0000 - 000000000f7f3000 (ACPI NVS) (XEN) 000000000f7f3000 - 000000000f800000 (ACPI data) (XEN) 00000000ffff0000 - 0000000100000000 (reserved) (XEN) System RAM: 247MB (253504kB) (XEN) Xen heap: 10MB (10672kB) (XEN) PAE disabled. (XEN) DMI 2.2 present. (XEN) Using APIC driver default (XEN) ACPI: RSDP (v000 VIA694 ) @ 0x000f76d0 (XEN) ACPI: RSDT (v001 VIA694 MSI ACPI 0x42302e31 AWRD 0x00000000) @ 0x0f7f3000 (XEN) ACPI: FADT (v001 VIA694 MSI ACPI 0x42302e31 AWRD 0x00000000) @ 0x0f7f3040 (XEN) ACPI: DSDT (v001 VIA694 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000 (XEN) Local APIC disabled by BIOS -- you can enable it with "lapic" (XEN) Initializing CPU#0 (XEN) Detected 1300.096 MHz processor. (XEN) Using scheduler: Simple EDF Scheduler (sedf) (XEN) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) (XEN) CPU: L2 Cache: 64K (64 bytes/line) (XEN) CPU0: AMD Duron(tm) processor stepping 01 (XEN) SMP motherboard not detected. (XEN) Local APIC not detected. Using dummy APIC emulation. (XEN) Platform timer is 1.193MHz PIT (XEN) Brought up 1 CPUs (XEN) mtrr: v2.0 (20020519) (XEN) *** LOADING DOMAIN 0 *** (XEN) Xen-ELF header found: ''GUEST_OS=linux,GUEST_VER=2.6,XEN_VER=3.0,VIRT_BASE=0xC0000000,PAE=no,LOADER=generic'' (XEN) PHYSICAL MEMORY ARRANGEMENT: (XEN) Dom0 alloc.: 01800000->02000000 (30702 pages to be allocated) (XEN) VIRTUAL MEMORY ARRANGEMENT: (XEN) Loaded kernel: c0100000->c0621a84 (XEN) Init. ramdisk: c0622000->c0657c00 (XEN) Phys-Mach map: c0658000->c0677fb8 (XEN) Page tables: c0678000->c067b000 (XEN) Start info: c067b000->c067c000 (XEN) Boot stack: c067c000->c067d000 (XEN) TOTAL: c0000000->c0800000 (XEN) ENTRY ADDRESS: c0100000 (XEN) Initrd len 0x35c00, start at 0xc0622000 (XEN) Scrubbing Free RAM: ...done. (XEN) *** Serial input -> DOM0 (type ''CTRL-a'' three times to switch input to Xen). (XEN) (file=irq.c, line=224) Cannot bind IRQ 2 to guest. In use by ''cascade''. (XEN) (file=irq.c, line=224) Cannot bind IRQ 2 to guest. In use by ''cascade''. (XEN) (file=irq.c, line=224) Cannot bind IRQ 2 to guest. In use by ''cascade''. (XEN) (file=irq.c, line=224) Cannot bind IRQ 2 to guest. In use by ''cascade''. Linux version 2.6.12-xen0 (root@localhost) (gcc version 4.0.1 (4.0.1-2mdk for Mandriva Linux release 2006.0)) #2 Thu Aug 25 10:19:08 EDT 2005 BIOS-provided physical RAM map: Xen: 0000000000100000 - 0000000007fee000 (usable) 0MB HIGHMEM available. 127MB LOWMEM available. On node 0 totalpages: 32750 DMA zone: 32750 pages, LIFO batch:15 Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 DMI 2.2 present. ACPI: RSDP (v000 VIA694 ) @ 0x000f76d0 ACPI: RSDT (v001 VIA694 MSI ACPI 0x42302e31 AWRD 0x00000000) @ 0x0f7f3000 ACPI: FADT (v001 VIA694 MSI ACPI 0x42302e31 AWRD 0x00000000) @ 0x0f7f3040 ACPI: DSDT (v001 VIA694 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000 IRQ lockup detection disabled Allocating PCI resources starting at 08000000 (gap: 07fee000:f8012000) Built 1 zonelists Kernel command line: ro root=/dev/hda1 Initializing CPU#0 PID hash table entries: 512 (order: 9, 8192 bytes) Xen reported: 1300.096 MHz processor. Console: colour VGA+ 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) vmalloc area: c8800000-fb7fe000, maxmem 34000000 Memory: 122752k/131000k available (3571k kernel code, 7004k reserved, 1034k data, 356k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 2595.22 BogoMIPS (lpj=12976128) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 64K (64 bytes/line) CPU: After all inits, caps: 0383d1f1 c1cbf9ff 00000000 00000020 00000000 00000000 00000000 CPU: AMD Duron(tm) processor stepping 01 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking ''hlt'' instruction... disabled ACPI: setting ELCR to 0008 (from 1c08) checking if image is initramfs...it isn''t (bad gzip magic numbers); looks like an initrd Freeing initrd memory: 215k freed NET: Registered protocol family 16 PCI: Using configuration type 1 ACPI: Subsystem revision 20050309 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Disabling VIA memory write queue (PCI ID 3112, rev 00): [55] f9 & 1f -> 19 Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 *12 14 15) xen_mem: Initialising balloon driver. SCSI subsystem initialized usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn''t work, try "pci=routeirq". If it helps, post a report Grant table initialized IA-32 Microcode Update Driver: v1.14-xen <tigran@veritas.com> Initializing Cryptographic API Applying VIA southbridge workaround. PCI: Disabling Via external APIC routing serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) HP CISS Driver (v 2.6.6) Intel(R) PRO/1000 Network Driver - version 6.0.54-k2 Copyright (c) 1999-2004 Intel Corporation. pcnet32.c:v1.30j 29.04.2005 tsbogend@alpha.franken.de e100: Intel(R) PRO/100 Network Driver, 3.4.8-k2-NAPI e100: Copyright(c) 1999-2005 Intel Corporation 8139too Fast Ethernet driver 0.9.27 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 eth0: RealTek RTL8139 at 0xdc00, 00:c0:df:03:2d:13, IRQ 11 eth0: Identified 8139 chip type ''RTL-8139B'' tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> Linux Tulip driver version 1.1.13 (May 11, 2002) ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 12 ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12 tulip0: MII transceiver #1 config 1000 status 7849 advertising 05e1. tulip0: MII transceiver #2 config 1000 status 7849 advertising 05e1. tulip0: MII transceiver #3 config 1000 status 7849 advertising 05e1. tulip0: MII transceiver #4 config 1000 status 7849 advertising 05e1. eth1: ADMtek Comet rev 17 at 0001e000, FE:FF:FF:FF:FF:FF, IRQ 12. Xen virtual console successfully installed as ttyS0 Event-channel device installed. Initialising Xen netif backend Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Probing IDE interface ide0... hda: SAMSUNG SP0802N, ATA DISK drive Probing IDE interface ide1... hdc: SONY CD-ROM CDU5221, ATAPI CD/DVD-ROM drive Probing IDE interface ide2... Probing IDE interface ide3... Probing IDE interface ide4... Probing IDE interface ide5... ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 1024KiB hda: 156368016 sectors (80060 MB) w/2048KiB Cache, CHS=16383/255/63 hda: cache flushes supported hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 > hdc: ATAPI 40X CD-ROM drive, 128kB Cache Uniform CD-ROM driver Revision: 3.20 Red Hat/Adaptec aacraid driver (1.1.2-lk2 Aug 25 2005) 3ware Storage Controller device driver for Linux v1.26.02.001. libata version 1.11 loaded. Fusion MPT base driver 3.01.20 Copyright (c) 1999-2004 LSI Logic Corporation Fusion MPT SCSI Host driver 3.01.20 usbmon: debugs is not available ohci_hcd: 2004 Nov 08 USB 1.1 ''Open'' Host Controller (OHCI) Driver (PCI) USB Universal Host Controller Interface driver v2.2 ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12 uhci_hcd 0000:00:07.2: UHCI Host Controller uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:07.2: irq 12, io base 0x0000c400 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12 uhci_hcd 0000:00:07.3: UHCI Host Controller uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:07.3: irq 12, io base 0x0000c800 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.01:USB HID core driver mice: PS/2 mouse device common for all mice md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid5 personality registered as nr 4 raid5: automatically using best checksumming function: pIII_sse pIII_sse : 1809.200 MB/sec raid5: using function: pIII_sse (1809.200 MB/sec) md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 4Kbytes TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) NET: Registered protocol family 1 NET: Registered protocol family 17 input: AT Translated Set 2 keyboard on isa0060/serio0 Bridge firewalling registered md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. RAMDISK: ext2 filesystem found at block 0 RAMDISK: Loading 212KiB [1 disk] into ram disk... |/-\|/-\|/-\|/done. VFS: Mounted root (ext2 filesystem). EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds Freeing unused kernel memory: 356k freed *************************************************************** *************************************************************** ** WARNING: Currently emulating unsupported memory accesses ** ** in /lib/tls libraries. The emulation is very ** ** slow. To ensure full performance you should ** ** execute the following as root: ** ** mv /lib/tls /lib/tls.disabled ** ** Offending process: hotplug (pid=806) ** *************************************************************** *************************************************************** Pausing... 5Pausing... 4Pausing... 3Pausing... 2Pausing... 1Continuing... ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (CM) [SLPB] ibm_acpi: ec object not found ACPI: CPU0 (power states: C1[C1] C2[C2]) ACPI: Processor [CPU0] (supports 2 throttling states) EXT3 FS on hda1, internal journal Adding 506008k swap on /dev/hda5. Priority:-1 extents:1 Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected VIA KLE133 chipset agpgart: AGP aperture is 4M @ 0xd4000000 ip_conntrack version 2.1 (1023 buckets, 8184 max) - 244 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timeout, status 0c 0005 c07f media 80. eth0: Tx queue start entry 4 dirty entry 0. eth0: Tx descriptor 0 is 0008a156. (queue head) eth0: Tx descriptor 1 is 0008a156. eth0: Tx descriptor 2 is 0008a156. eth0: Tx descriptor 3 is 0008a156. eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timeout, status 0c 0005 c07f media 80. eth0: Tx queue start entry 4 dirty entry 0. eth0: Tx descriptor 0 is 0008a156. (queue head) eth0: Tx descriptor 1 is 0008a156. eth0: Tx descriptor 2 is 0008a156. eth0: Tx descriptor 3 is 0008a156. eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timeout, status 0c 0005 c07f media 80. eth0: Tx queue start entry 4 dirty entry 0. eth0: Tx descriptor 0 is 0008a156. (queue head) eth0: Tx descriptor 1 is 0008a156. eth0: Tx descriptor 2 is 0008a156. eth0: Tx descriptor 3 is 0008a156. eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 -- Flávio Bruno Leitner <fbl@conectiva.com.br> [0EA2 7F40 4CF4 1E63 4AF6 33C0 3E10 E205 F251 EDDA] _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel
Flavio Leitner
2005-Aug-26 12:35 UTC
Re: [Xen-devel] network interface not responding in dom0
On Thu, Aug 25, 2005 at 02:39:04PM -0300, Flavio Leitner wrote:> I''m using xen-unstable tarball downloaded 25/08/05 and have > two network cards installed on this machine. None of them > is working. > > The /proc/interrupts shows eth0 alone but always with 0 > interrupts. > > Xen version 3.0-devel (root@) (gcc version 4.0.1 (4.0.1-2mdk for Mandriva Linux release 2006.0)) Thu Aug 25 10:19:50 EDT 2005Using gcc-3.3.6 fixed all issues. -- Flávio Bruno Leitner <fbl@conectiva.com.br> [0EA2 7F40 4CF4 1E63 4AF6 33C0 3E10 E205 F251 EDDA] _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel