> -----Original Message-----
> From: xen-devel-admin@lists.sourceforge.net [mailto:xen-devel-
> admin@lists.sourceforge.net] On Behalf Of Xiaofang Chen
> Sent: 11 April 2004 04:24
> To: Steven Hand
> Cc: xen-devel@lists.sourceforge.net
> Subject: [Xen-devel] New Domain
>
> Thanks, I am clear on this now.
>
> Another question, could you help me look at the
"xen_read_console"
output?> It''s in the attachement.
> The output of xc_dom_create -Dvmid=1 is as follows:
> ./xc_dom_create.py -Dvmid=1
> Parsing config file ''/etc/xc/defaults''
> VM image : "/boot/xenolinux.gz"
> VM ramdisk : ""
> VM memory (MB) : "16"
> VM IP address(es) : "169.254.1.1"
> VM block device(s) : "phy:hda11,hda11,w"
> VM cmdline :
>
"ip=169.254.1.1:169.254.1.0:155.99.182.1:255.255.254.0::eth0:on> root=/dev/hda11 ro 4 VMID=1"
> VM started in domain 1
>
> The ifcfg-eth0 is using static IP address, not DHCP.
> Seems that the new domain starts with no problem, but I couldn''t
ping
&> ssh
> into it.
Ping/ssh from where? You are assigning VMM local address to the domain
(169.254/16) which are not send on the LAN. You won''t be able to ping
that domain from another machine.
If you try to ping/access that domain from another domain on the same
machine you also have to configure that domains IP address properly (or
better, create an alias). For example, dom0 should have an alias for the
169.254 subnet.
Your gateway address 155.99.182.1 is on a completely different subnet.
Rolf
> Thanks for your help.
>
> Xiaofang
>
>
> > The vbd_list consists of entries of the form
> >
> > (<real device>, <virt device>, <mode>)
> >
> > where <real device> is the name of the device (disk, partition,
> whatever)
> > under ''normal'' linux, or from the first xenolinux
(domain 0), and
> > <virt device> is the name you want the new domain (e.g. domain
1) to
> > refer to it as, and <mode> is ''w'' for
read-write or ''r'' for
read-only.> >
> > Hence the first item in each entry in vbd_list will be a "real
physical> > partition", but the others will not. No real device should appear
more> > than once (since that means you would be trying to let the new
domain> > access the same device more than once, which is bad), and no virt
device> > should appear more than once (since this means you have conflicting
> ideas
> > about what that device should be mapped to).
> >
> > Furthermore, any [real] device should be accessed either exactly
once> > in read-write mode (by all domains), or may be accessed read-only by
> > as many domains as you like.
> >
> > Hence your setup
> >
> > > > vbd_list = [
(''phy:hda1'',''sda1'',''w''),
(''phy:hda1'',''sda6'',''r'')
]> >
> > is definitely wrong since (a) it attempts to export the same real
device> > phy:hda1 more than once and (b) it attempts to export a device both
> > read-only and read-write.
> >
> > >And what the "cmdline_root" should be?
> >
> > This should be the ''virt device'' you have set up to
point to a real
> > device that has a root file system for that domain on it.
> >
> > There''s more information in the HOWTOs, FAQs and READMEs.
> >
> > S.