Virtualization - Nov 2012 - [PATCHv4] virtio-spec: virtio network device RFS support

Add RFS support to virtio network device.
Add a new feature flag VIRTIO_NET_F_RFS for this feature, a new
configuration field max_virtqueue_pairs to detect supported number of
virtqueues as well as a new command VIRTIO_NET_CTRL_RFS to program
packet steering for unidirectional protocols.

Signed-off-by: Michael S. Tsirkin <mst at redhat.com>

--

Changes from v3:
- rename multiqueue -> rfs this is what we support
- Be more explicit about what driver should do.
- Simplify layout making VQs functionality depend on feature.
- Remove unused commands, only leave in programming # of queues

Changes from v2:
Address Jason's comments on v2:
- Changed STEERING_HOST to STEERING_RX_FOLLOWS_TX:
  this is both clearer and easier to support.
  It does not look like we need a separate steering command
  since host can just watch tx packets as they go.
- Moved RX and TX steering sections near each other.
- Add motivation for other changes in v2

Changes from Jason's rfc:
- reserved vq 3: this makes all rx vqs even and tx vqs odd, which
  looks nicer to me.
- documented packet steering, added a generalized steering programming
  command. Current modes are single queue and host driven multiqueue,
  but I envision support for guest driven multiqueue in the future.
- make default vqs unused when in mq mode - this wastes some memory
  but makes it more efficient to switch between modes as
  we can avoid this causing packet reordering.

Rusty, could you please take a look and comment soon?
If this looks OK to everyone, we can proceed with finalizing the
implementation. Would be nice to try and put it in 3.8.

---

diff --git a/virtio-spec.lyx b/virtio-spec.lyx
index d2f0da9..c1fa3e4 100644
--- a/virtio-spec.lyx
+++ b/virtio-spec.lyx
@@ -59,6 +59,7 @@
 \author -608949062 "Rusty Russell,,," 
 \author -385801441 "Cornelia Huck" cornelia.huck at de.ibm.com
 \author 1531152142 "Paolo Bonzini,,," 
+\author 1986246365 "Michael S. Tsirkin" 
 \end_header
 
 \begin_body
@@ -4170,9 +4171,42 @@ ID 1
 \end_layout
 
 \begin_layout Description
-Virtqueues 0:receiveq.
- 1:transmitq.
- 2:controlq
+Virtqueues 0:receiveq
+\change_inserted 1986246365 1352742829
+0
+\change_unchanged
+.
+ 1:transmitq
+\change_inserted 1986246365 1352742832
+0
+\change_deleted 1986246365 1352742947
+.
+ 
+\change_inserted 1986246365 1352742952
+.
+ ....
+ 2N
+\begin_inset Foot
+status open
+
+\begin_layout Plain Layout
+
+\change_inserted 1986246365 1352743187
+N=0 if VIRTIO_NET_F_RFS is not negotiated, otherwise N is indicated by max_
+\emph on
+virtqueue_pairs control
+\emph default
+ field.
+ 
+\end_layout
+
+\end_inset
+
+: receivqN.
+ 2N+1: transmitqN.
+ 2N+
+\change_unchanged
+2:controlq
 \begin_inset Foot
 status open
 
@@ -4343,6 +4377,16 @@ VIRTIO_NET_F_CTRL_VLAN
 
 \begin_layout Description
 VIRTIO_NET_F_GUEST_ANNOUNCE(21) Guest can send gratuitous packets.
+\change_inserted 1986246365 1352742767
+
+\end_layout
+
+\begin_layout Description
+
+\change_inserted 1986246365 1352742808
+VIRTIO_NET_F_RFS(2) Device supports Receive Flow Steering.
+\change_unchanged
+
 \end_layout
 
 \end_deeper
@@ -4355,11 +4399,44 @@ configuration
 \begin_inset space ~
 \end_inset
 
-layout Two configuration fields are currently defined.
+layout 
+\change_deleted 1986246365 1352743300
+Two
+\change_inserted 1986246365 1352743301
+Four
+\change_unchanged
+ configuration fields are currently defined.
  The mac address field always exists (though is only valid if VIRTIO_NET_F_MAC
  is set), and the status field only exists if VIRTIO_NET_F_STATUS is set.
  Two read-only bits are currently defined for the status field:
VIRTIO_NET_S_LIN
 K_UP and VIRTIO_NET_S_ANNOUNCE.
+
+\change_inserted 1986246365 1353595219
+ The following read-only field, 
+\emph on
+max_virtqueue_pairs
+\emph default
+ only exists if VIRTIO_NET_F_RFS is set.
+ This field specifies the maximum number of each of transmit and receive
+ virtqueues (receiveq0..receiveq
+\emph on
+N
+\emph default
+ and transmitq0..transmitq
+\emph on
+N
+\emph default
+ respectively; 
+\emph on
+N
+\emph default
++\emph on
+max_virtqueue_pairs
+\emph default
+) that can be configured once VIRTIO_NET_F_RFS is negotiated.
+
+\change_unchanged
  
 \begin_inset listings
 inline false
@@ -4410,7 +4487,24 @@ Device Initialization
 
 \begin_layout Enumerate
 The initialization routine should identify the receive and transmission
- virtqueues.
+ virtqueues
+\change_inserted 1986246365 1352744077
+, up to N+1 of each kind
+\change_unchanged
+.
+
+\change_inserted 1986246365 1352743942
+ If VIRTIO_NET_F_RFS feature bit is negotiated, 
+\emph on
+N=max_virtqueue_pairs
+\emph default
+, otherwise identify 
+\emph on
+N=0
+\emph default
+.
+\change_unchanged
+
 \end_layout
 
 \begin_layout Enumerate
@@ -4455,7 +4549,11 @@ status
 \end_layout
 
 \begin_layout Enumerate
-The receive virtqueue should be filled with receive buffers.
+The receive virtqueue
+\change_inserted 1986246365 1352743953
+s
+\change_unchanged
+ should be filled with receive buffers.
  This is described in detail below in 
 \begin_inset Quotes eld
 \end_inset
@@ -4550,8 +4648,15 @@ Device Operation
 \end_layout
 
 \begin_layout Standard
-Packets are transmitted by placing them in the transmitq, and buffers for
- incoming packets are placed in the receiveq.
+Packets are transmitted by placing them in the transmitq
+\change_inserted 1986246365 1353593685
+0..transmitqN
+\change_unchanged
+, and buffers for incoming packets are placed in the receiveq
+\change_inserted 1986246365 1353593692
+0..receiveqN
+\change_unchanged
+.
  In each case, the packet itself is preceeded by a header:
 \end_layout
 
@@ -4861,6 +4966,17 @@ If VIRTIO_NET_F_MRG_RXBUF is negotiated, each buffer must
be at least the
 struct virtio_net_hdr
 \family default
 .
+\change_inserted 1986246365 1353594518
+
+\end_layout
+
+\begin_layout Standard
+
+\change_inserted 1986246365 1353594638
+If VIRTIO_NET_F_RFS is negotiated, each of the receiveq0...receiveqN that will
+ be used should be populated with receive buffers.
+\change_unchanged
+
 \end_layout
 
 \begin_layout Subsection*
@@ -5293,8 +5409,125 @@ Sending VIRTIO_NET_CTRL_ANNOUNCE_ACK command through
control vq.
  
 \end_layout
 
-\begin_layout Enumerate
+\begin_layout Subsection*
+
+\change_inserted 1986246365 1353593879
+Packet Receive Flow Steering
+\end_layout
+
+\begin_layout Standard
+
+\change_inserted 1986246365 1353594403
+If the driver negotiates the VIRTIO_NET_F_RFS (depends on
VIRTIO_NET_F_CTRL_VQ),
+ it can transmit outgoing packets on one of the multiple transmitq0..transmitqN
+ and ask the device to queue incoming packets into one the multiple
receiveq0..rec
+eiveqN depending on the packet flow.
+\change_unchanged
+
+\end_layout
+
+\begin_layout Standard
+
+\change_inserted 1986246365 1353594292
+\begin_inset listings
+inline false
+status open
+
+\begin_layout Plain Layout
+
+\change_inserted 1986246365 1353594178
+
+struct virtio_net_ctrl_rfs {
+\end_layout
+
+\begin_layout Plain Layout
+
+\change_inserted 1986246365 1353594212
+
+	u16 virtqueue_pairs;
+\end_layout
+
+\begin_layout Plain Layout
+
+\change_inserted 1986246365 1353594172
+
+};
+\end_layout
+
+\begin_layout Plain Layout
+
+\change_inserted 1986246365 1353594172
+
+\end_layout
+
+\begin_layout Plain Layout
+
+\change_inserted 1986246365 1353594263
+
+#define VIRTIO_NET_CTRL_RFC    1
+\end_layout
+
+\begin_layout Plain Layout
+
+\change_inserted 1986246365 1353594273
+
+ #define VIRTIO_NET_CTRL_RFS_VQ_PAIRS_SET        0 
+\end_layout
+
+\end_inset
+
+
+\end_layout
+
+\begin_layout Standard
+
+\change_inserted 1986246365 1353594884
+RFS acceleration is disabled by default.
+ Driver enables RFS by executing the VIRTIO_NET_CTRL_RFS_VQ_PAIRS_SET command,
+ specifying the number of the last transmit and receive queue that is going
+ to be used; thus out of transmitq0..transmitqn and receiveq0..receiveqn where
+ 
+\emph on
+n=virtqueue
+\emph default
+_pairs will be used.
+ All these virtqueues must have been pre-configured in advance.
+\end_layout
+
+\begin_layout Standard
+
+\change_inserted 1986246365 1353595328
+Programming of the receive flow classificator is implicit.
+ Transmitting a packet of a specific flow on transmitqX will cause incoming
+ packets for this flow to be steered to receiveqX.
+ For uni-directional protocols, or where no packets have been transmitted
+ yet, device will steer a packet to a random queue out of the specified
+ receiveq0..receiveqn.
+\change_unchanged
+
+\end_layout
+
+\begin_layout Standard
+
+\change_inserted 1986246365 1353595040
+RFS acceleration is disabled by setting 
+\emph on
+virtqueue_pairs = 0
+\emph default
+ (this is the default).
+ Following this, driver should not transmit new packets on virtqueues other
+ than transmitq0 and device will not steer new packets on virtqueues other
+ than receiveq0.
+\change_unchanged
+
+\end_layout
+
+\begin_layout Standard
+
+\change_deleted 1986246365 1353593873
 .
+
+\change_unchanged
  
 \end_layout
 
@@ -6152,13 +6385,7 @@ Virtqueues 0:receiveq(port0).
 status open
 
 \begin_layout Plain Layout
-Ports 
-\change_inserted 1986246365 1347188327
-1
-\change_deleted 1986246365 1347188327
-2
-\change_unchanged
- onwards only if VIRTIO_CONSOLE_F_MULTIPORT is set
+Ports 12 onwards only if VIRTIO_CONSOLE_F_MULTIPORT is set
 \end_layout
 
 \end_inset
@@ -6185,13 +6412,8 @@ VIRTIO_CONSOLE_F_SIZE
 
 \begin_layout Description
 VIRTIO_CONSOLE_F_MULTIPORT(1) Device has support for multiple ports;
configurati
-on fields nr_ports and max_nr_ports are valid
-\change_inserted 1986246365 1347188404
-; if this bit is negotiated,
-\change_deleted 1986246365 1347188406
- and
-\change_unchanged
- control virtqueues will be used.
+on fields nr_ports and max_nr_ports are valid; if this bit is negotiated,
+ and control virtqueues will be used.
 \end_layout
 
 \end_deeper
@@ -6260,8 +6482,7 @@ If the VIRTIO_CONSOLE_F_MULTIPORT feature is negotiated,
the driver can
  spawn multiple ports, not all of which may be attached to a console.
  Some could be generic ports.
  In this case, the control virtqueues are enabled and according to the
max_nr_po
-rts configuration-space value, an appropriate number of virtqueues are
- created.
+rts configuration-space value, an appropriate number of virtqueues are created.
  A control message indicating the driver is ready is sent to the host.
  The host can then send control messages for adding new ports to the device.
  After creating and initializing each port, a VIRTIO_CONSOLE_PORT_READY
@@ -6699,14 +6920,9 @@ The driver constructs an array of addresses of memory
pages it has previously
 \end_layout
 
 \begin_layout Enumerate
-If the VIRTIO_BALLOON_F_MUST_TELL_HOST feature is 
-\change_inserted 1986246365 1347188540
-negotiated
-\change_deleted 1986246365 1347188542
-set
-\change_unchanged
-, the guest may not use these requested pages until that descriptor in the
- deflateq has been used by the device.
+If the VIRTIO_BALLOON_F_MUST_TELL_HOST feature is negotiatedset, the guest
+ may not use these requested pages until that descriptor in the deflateq
+ has been used by the device.
 \end_layout
 
 \begin_layout Enumerate

On 11/22/2012 10:46 PM, Michael S. Tsirkin wrote:
> Add RFS support to virtio network device.
> Add a new feature flag VIRTIO_NET_F_RFS for this feature, a new
> configuration field max_virtqueue_pairs to detect supported number of
> virtqueues as well as a new command VIRTIO_NET_CTRL_RFS to program
> packet steering for unidirectional protocols.
>
> Signed-off-by: Michael S. Tsirkin <mst at redhat.com>
>
> --
>
> Changes from v3:
> - rename multiqueue -> rfs this is what we support
> - Be more explicit about what driver should do.
> - Simplify layout making VQs functionality depend on feature.
> - Remove unused commands, only leave in programming # of queues
>
> Changes from v2:
> Address Jason's comments on v2:
> - Changed STEERING_HOST to STEERING_RX_FOLLOWS_TX:
>    this is both clearer and easier to support.
>    It does not look like we need a separate steering command
>    since host can just watch tx packets as they go.
> - Moved RX and TX steering sections near each other.
> - Add motivation for other changes in v2
>
> Changes from Jason's rfc:
> - reserved vq 3: this makes all rx vqs even and tx vqs odd, which
>    looks nicer to me.
> - documented packet steering, added a generalized steering programming
>    command. Current modes are single queue and host driven multiqueue,
>    but I envision support for guest driven multiqueue in the future.
> - make default vqs unused when in mq mode - this wastes some memory
>    but makes it more efficient to switch between modes as
>    we can avoid this causing packet reordering.
>
> Rusty, could you please take a look and comment soon?
> If this looks OK to everyone, we can proceed with finalizing the
> implementation. Would be nice to try and put it in 3.8.
>
> ---
>
> diff --git a/virtio-spec.lyx b/virtio-spec.lyx
> index d2f0da9..c1fa3e4 100644
> --- a/virtio-spec.lyx
> +++ b/virtio-spec.lyx
> @@ -59,6 +59,7 @@
>   \author -608949062 "Rusty Russell,,,"
>   \author -385801441 "Cornelia Huck" cornelia.huck at de.ibm.com
>   \author 1531152142 "Paolo Bonzini,,,"
> +\author 1986246365 "Michael S. Tsirkin"
>   \end_header
>   
>   \begin_body
> @@ -4170,9 +4171,42 @@ ID 1
>   \end_layout
>   
>   \begin_layout Description
> -Virtqueues 0:receiveq.
> - 1:transmitq.
> - 2:controlq
> +Virtqueues 0:receiveq
> +\change_inserted 1986246365 1352742829
> +0
> +\change_unchanged
> +.
> + 1:transmitq
> +\change_inserted 1986246365 1352742832
> +0
> +\change_deleted 1986246365 1352742947
> +.
> +
> +\change_inserted 1986246365 1352742952
> +.
> + ....
> + 2N
> +\begin_inset Foot
> +status open
> +
> +\begin_layout Plain Layout
> +
> +\change_inserted 1986246365 1352743187
> +N=0 if VIRTIO_NET_F_RFS is not negotiated, otherwise N is indicated by
max_
> +\emph on
> +virtqueue_pairs control
> +\emph default
> + field.
> +
> +\end_layout
> +
> +\end_inset
> +
> +: receivqN.
> + 2N+1: transmitqN.
> + 2N+
> +\change_unchanged
> +2:controlq
>   \begin_inset Foot
>   status open
>   
> @@ -4343,6 +4377,16 @@ VIRTIO_NET_F_CTRL_VLAN
>   
>   \begin_layout Description
>   VIRTIO_NET_F_GUEST_ANNOUNCE(21) Guest can send gratuitous packets.
> +\change_inserted 1986246365 1352742767
> +
> +\end_layout
> +
> +\begin_layout Description
> +
> +\change_inserted 1986246365 1352742808
> +VIRTIO_NET_F_RFS(2) Device supports Receive Flow Steering.
> +\change_unchanged
should be 22
> +
>   \end_layout
>   
>   \end_deeper
> @@ -4355,11 +4399,44 @@ configuration
>   \begin_inset space ~
>   \end_inset
>   
> -layout Two configuration fields are currently defined.
> +layout
> +\change_deleted 1986246365 1352743300
> +Two
> +\change_inserted 1986246365 1352743301
> +Four
> +\change_unchanged
> + configuration fields are currently defined.
>    The mac address field always exists (though is only valid if
VIRTIO_NET_F_MAC
>    is set), and the status field only exists if VIRTIO_NET_F_STATUS is set.
>    Two read-only bits are currently defined for the status field:
VIRTIO_NET_S_LIN
>   K_UP and VIRTIO_NET_S_ANNOUNCE.
> +
> +\change_inserted 1986246365 1353595219
> + The following read-only field,
> +\emph on
> +max_virtqueue_pairs
> +\emph default
> + only exists if VIRTIO_NET_F_RFS is set.
> + This field specifies the maximum number of each of transmit and receive
> + virtqueues (receiveq0..receiveq
> +\emph on
> +N
> +\emph default
> + and transmitq0..transmitq
> +\emph on
> +N
> +\emph default
> + respectively;
> +\emph on
> +N
> +\emph default
> +> +\emph on
> +max_virtqueue_pairs
> +\emph default
> +) that can be configured once VIRTIO_NET_F_RFS is negotiated.
> +
> +\change_unchanged
So the virt queues used in single queue mode is still reserved in 
multiqueue mode, since when max_virtqueue_pairs in N, we finally get N+1 
virt queue pairs? And this looks conflict with the description in 
"Packet Receive Flow Steering":

"specifying the number of the last transmit and receive queue that is 
going to be used; thus out of transmitq0..transmitqn and 
receiveq0..receiveqn where n=virtqueue_pairs will be used."

In this description, looks like n+1 virtqueue pairs (include receiveq0 
and transmitq0) could be used in RFS mode.
>    
>   \begin_inset listings
>   inline false
> @@ -4410,7 +4487,24 @@ Device Initialization
>   
>   \begin_layout Enumerate
>   The initialization routine should identify the receive and transmission
> - virtqueues.
> + virtqueues
> +\change_inserted 1986246365 1352744077
> +, up to N+1 of each kind
> +\change_unchanged
> +.
> +
> +\change_inserted 1986246365 1352743942
> + If VIRTIO_NET_F_RFS feature bit is negotiated,
> +\emph on
> +N=max_virtqueue_pairs
> +\emph default
> +, otherwise identify
> +\emph on
> +N=0
> +\emph default
> +.
> +\change_unchanged
> +
>   \end_layout
>   
>   \begin_layout Enumerate
> @@ -4455,7 +4549,11 @@ status
>   \end_layout
>   
>   \begin_layout Enumerate
> -The receive virtqueue should be filled with receive buffers.
> +The receive virtqueue
> +\change_inserted 1986246365 1352743953
> +s
> +\change_unchanged
> + should be filled with receive buffers.
>    This is described in detail below in
>   \begin_inset Quotes eld
>   \end_inset
> @@ -4550,8 +4648,15 @@ Device Operation
>   \end_layout
>   
>   \begin_layout Standard
> -Packets are transmitted by placing them in the transmitq, and buffers for
> - incoming packets are placed in the receiveq.
> +Packets are transmitted by placing them in the transmitq
> +\change_inserted 1986246365 1353593685
> +0..transmitqN
> +\change_unchanged
> +, and buffers for incoming packets are placed in the receiveq
> +\change_inserted 1986246365 1353593692
> +0..receiveqN
> +\change_unchanged
> +.
>    In each case, the packet itself is preceeded by a header:
>   \end_layout
>   
> @@ -4861,6 +4966,17 @@ If VIRTIO_NET_F_MRG_RXBUF is negotiated, each buffer
must be at least the
>   struct virtio_net_hdr
>   \family default
>   .
> +\change_inserted 1986246365 1353594518
> +
> +\end_layout
> +
> +\begin_layout Standard
> +
> +\change_inserted 1986246365 1353594638
> +If VIRTIO_NET_F_RFS is negotiated, each of the receiveq0...receiveqN that
will
> + be used should be populated with receive buffers.
> +\change_unchanged
> +
>   \end_layout
>   
>   \begin_layout Subsection*
> @@ -5293,8 +5409,125 @@ Sending VIRTIO_NET_CTRL_ANNOUNCE_ACK command
through control vq.
>    
>   \end_layout
>   
> -\begin_layout Enumerate
> +\begin_layout Subsection*
> +
> +\change_inserted 1986246365 1353593879
> +Packet Receive Flow Steering
> +\end_layout
> +
> +\begin_layout Standard
> +
> +\change_inserted 1986246365 1353594403
> +If the driver negotiates the VIRTIO_NET_F_RFS (depends on
VIRTIO_NET_F_CTRL_VQ),
> + it can transmit outgoing packets on one of the multiple
transmitq0..transmitqN
> + and ask the device to queue incoming packets into one the multiple
receiveq0..rec
> +eiveqN depending on the packet flow.
> +\change_unchanged
> +
> +\end_layout
> +
> +\begin_layout Standard
> +
> +\change_inserted 1986246365 1353594292
> +\begin_inset listings
> +inline false
> +status open
> +
> +\begin_layout Plain Layout
> +
> +\change_inserted 1986246365 1353594178
> +
> +struct virtio_net_ctrl_rfs {
> +\end_layout
> +
> +\begin_layout Plain Layout
> +
> +\change_inserted 1986246365 1353594212
> +
> +	u16 virtqueue_pairs;
> +\end_layout
> +
> +\begin_layout Plain Layout
> +
> +\change_inserted 1986246365 1353594172
> +
> +};
> +\end_layout
> +
> +\begin_layout Plain Layout
> +
> +\change_inserted 1986246365 1353594172
> +
> +\end_layout
> +
> +\begin_layout Plain Layout
> +
> +\change_inserted 1986246365 1353594263
> +
> +#define VIRTIO_NET_CTRL_RFC    1
RFS
> +\end_layout
> +
> +\begin_layout Plain Layout
> +
> +\change_inserted 1986246365 1353594273
> +
> + #define VIRTIO_NET_CTRL_RFS_VQ_PAIRS_SET        0
> +\end_layout
> +
> +\end_inset
> +
> +
> +\end_layout
> +
> +\begin_layout Standard
> +
> +\change_inserted 1986246365 1353594884
> +RFS acceleration is disabled by default.
> + Driver enables RFS by executing the VIRTIO_NET_CTRL_RFS_VQ_PAIRS_SET
command,
> + specifying the number of the last transmit and receive queue that is
going
> + to be used; thus out of transmitq0..transmitqn and receiveq0..receiveqn
where
> +
> +\emph on
> +n=virtqueue
> +\emph default
> +_pairs will be used.
> + All these virtqueues must have been pre-configured in advance.
> +\end_layout
> +
> +\begin_layout Standard
> +
> +\change_inserted 1986246365 1353595328
> +Programming of the receive flow classificator is implicit.
> + Transmitting a packet of a specific flow on transmitqX will cause
incoming
> + packets for this flow to be steered to receiveqX.
> + For uni-directional protocols, or where no packets have been transmitted
> + yet, device will steer a packet to a random queue out of the specified
> + receiveq0..receiveqn.
> +\change_unchanged
> +
> +\end_layout
> +
> +\begin_layout Standard
> +
> +\change_inserted 1986246365 1353595040
> +RFS acceleration is disabled by setting
> +\emph on
> +virtqueue_pairs = 0
Zero looks a little bit misleading, use 1 here is more clear since we 
would still use 1 queue pairs.
> +\emph default
> + (this is the default).
> + Following this, driver should not transmit new packets on virtqueues
other
> + than transmitq0 and device will not steer new packets on virtqueues other
> + than receiveq0.
> +\change_unchanged
> +
> +\end_layout
> +
> +\begin_layout Standard
> +
> +\change_deleted 1986246365 1353593873
>   .
> +
> +\change_unchanged
>    
>   \end_layout
>   
> @@ -6152,13 +6385,7 @@ Virtqueues 0:receiveq(port0).
>   status open
>   
>   \begin_layout Plain Layout
> -Ports
> -\change_inserted 1986246365 1347188327
> -1
> -\change_deleted 1986246365 1347188327
> -2
> -\change_unchanged
> - onwards only if VIRTIO_CONSOLE_F_MULTIPORT is set
> +Ports 12 onwards only if VIRTIO_CONSOLE_F_MULTIPORT is set
The changes here and follow looks unrelated.
>   \end_layout
>   
>   \end_inset
> @@ -6185,13 +6412,8 @@ VIRTIO_CONSOLE_F_SIZE
>   
>   \begin_layout Description
>   VIRTIO_CONSOLE_F_MULTIPORT(1) Device has support for multiple ports;
configurati
> -on fields nr_ports and max_nr_ports are valid
> -\change_inserted 1986246365 1347188404
> -; if this bit is negotiated,
> -\change_deleted 1986246365 1347188406
> - and
> -\change_unchanged
> - control virtqueues will be used.
> +on fields nr_ports and max_nr_ports are valid; if this bit is negotiated,
> + and control virtqueues will be used.
>   \end_layout
>   
>   \end_deeper
> @@ -6260,8 +6482,7 @@ If the VIRTIO_CONSOLE_F_MULTIPORT feature is
negotiated, the driver can
>    spawn multiple ports, not all of which may be attached to a console.
>    Some could be generic ports.
>    In this case, the control virtqueues are enabled and according to the
max_nr_po
> -rts configuration-space value, an appropriate number of virtqueues are
> - created.
> +rts configuration-space value, an appropriate number of virtqueues are
created.
>    A control message indicating the driver is ready is sent to the host.
>    The host can then send control messages for adding new ports to the
device.
>    After creating and initializing each port, a VIRTIO_CONSOLE_PORT_READY
> @@ -6699,14 +6920,9 @@ The driver constructs an array of addresses of
memory pages it has previously
>   \end_layout
>   
>   \begin_layout Enumerate
> -If the VIRTIO_BALLOON_F_MUST_TELL_HOST feature is
> -\change_inserted 1986246365 1347188540
> -negotiated
> -\change_deleted 1986246365 1347188542
> -set
> -\change_unchanged
> -, the guest may not use these requested pages until that descriptor in the
> - deflateq has been used by the device.
> +If the VIRTIO_BALLOON_F_MUST_TELL_HOST feature is negotiatedset, the guest
> + may not use these requested pages until that descriptor in the deflateq
> + has been used by the device.
>   \end_layout
>   
>   \begin_layout Enumerate

"Michael S. Tsirkin" <mst at redhat.com>
writes:
> Add RFS support to virtio network device.
> Add a new feature flag VIRTIO_NET_F_RFS for this feature, a new
> configuration field max_virtqueue_pairs to detect supported number of
> virtqueues as well as a new command VIRTIO_NET_CTRL_RFS to program
> packet steering for unidirectional protocols.
Hi Michael,

        Sorry for the delay, I took last week off.
> - rename multiqueue -> rfs this is what we support
> - Be more explicit about what driver should do.
> - Simplify layout making VQs functionality depend on feature.
> - Remove unused commands, only leave in programming # of queues
Thanks: this looks really nice now.  Comments are about the text, not
the ideas.
> + 2N+1: transmitqN.
> + 2N+
> +\change_unchanged
> +2:controlq
>  \begin_inset Foot
>  status open
Hmm, controlq after xmit queues... a nice improvement.
> +VIRTIO_NET_F_RFS(2) Device supports Receive Flow Steering.
I think readers would prefer numerical order to historical order here,
so perhaps move this up in the list.
> -layout Two configuration fields are currently defined.
> +layout 
> +\change_deleted 1986246365 1352743300
> +Two
> +\change_inserted 1986246365 1352743301
> +Four
> +\change_unchanged
> + configuration fields are currently defined.
two to four?  I only see three?  And you didn't update the structure to
match...
> + Following this, driver should not transmit new packets on virtqueues
other
> + than transmitq0 and device will not steer new packets on virtqueues other
> + than receiveq0.
"Following this" is vague.  After the buffer is consumed by the
device.

Should not is kind of meaningless.  Let's make it clear: the device will
not steer new packets to RxqN, nor read from TxqN.

You should probably put in a note about the RFS control in the Device
Initialization section, too, ie. if you have negotiated and want to use
more queues, you must initialize them then wait for the ack of the
CTRL_RFS cmd.

Note: the following hunks didn't apply, but I'm not sure why they're
in
this anyway...
> @@ -6152,13 +6385,7 @@ Virtqueues 0:receiveq(port0).
>  status open
>  
>  \begin_layout Plain Layout
> -Ports 
> -\change_inserted 1986246365 1347188327
> -1
> -\change_deleted 1986246365 1347188327
> -2
> -\change_unchanged
> - onwards only if VIRTIO_CONSOLE_F_MULTIPORT is set
> +Ports 12 onwards only if VIRTIO_CONSOLE_F_MULTIPORT is set
>  \end_layout
>  
>  \end_inset
> @@ -6185,13 +6412,8 @@ VIRTIO_CONSOLE_F_SIZE
>  
>  \begin_layout Description
>  VIRTIO_CONSOLE_F_MULTIPORT(1) Device has support for multiple ports;
configurati
> -on fields nr_ports and max_nr_ports are valid
> -\change_inserted 1986246365 1347188404
> -; if this bit is negotiated,
> -\change_deleted 1986246365 1347188406
> - and
> -\change_unchanged
> - control virtqueues will be used.
> +on fields nr_ports and max_nr_ports are valid; if this bit is negotiated,
> + and control virtqueues will be used.
>  \end_layout
>  
>  \end_deeper
> @@ -6260,8 +6482,7 @@ If the VIRTIO_CONSOLE_F_MULTIPORT feature is
negotiated, the driver can
>   spawn multiple ports, not all of which may be attached to a console.
>   Some could be generic ports.
>   In this case, the control virtqueues are enabled and according to the
max_nr_po
> -rts configuration-space value, an appropriate number of virtqueues are
> - created.
> +rts configuration-space value, an appropriate number of virtqueues are
created.
>   A control message indicating the driver is ready is sent to the host.
>   The host can then send control messages for adding new ports to the
device.
>   After creating and initializing each port, a VIRTIO_CONSOLE_PORT_READY
> @@ -6699,14 +6920,9 @@ The driver constructs an array of addresses of
memory pages it has previously
>  \end_layout
>  
>  \begin_layout Enumerate
> -If the VIRTIO_BALLOON_F_MUST_TELL_HOST feature is 
> -\change_inserted 1986246365 1347188540
> -negotiated
> -\change_deleted 1986246365 1347188542
> -set
> -\change_unchanged
> -, the guest may not use these requested pages until that descriptor in the
> - deflateq has been used by the device.
> +If the VIRTIO_BALLOON_F_MUST_TELL_HOST feature is negotiatedset, the guest
> + may not use these requested pages until that descriptor in the deflateq
> + has been used by the device.
>  \end_layout
>  
>  \begin_layout Enumerate

Cheers,
Rusty.