similar to: diamond/triangle "plot"

Displaying 20 results from an estimated 500 matches similar to: "diamond/triangle "plot""

2018 Dec 16
3
detailed ups.test.result
My UPS has an LCD that says the battery is 100% and the estimated run time is 12min. The uspc has similar results. The problem is when line power is lost the UPS batter goes to 0% very quickly (seconds). It charged to 85% when power was restored. 86-100% is slower. I did: $ upscmd desktop_ups test.battery.start.deep Username (admin): Password: OK Now the ups.test.result says there is a
2012 Apr 04
2
question on DHCP
If a machine with centos 6.2 is set for DHCP and it looses power and the switch looses power for a long time. lets say a day. so the switch really goes off even with batter backup. Now power comes on, the machine asks for a DHCP address before the switch is read as its not back up yet. there is no response and the machine does not get an address. Finally the switch comes back up , the machine
2014 Feb 13
2
Eaton Powerware 5110 - some stats not reported
Hi all, I've hooked up an Eaton Powerware 5110 to Ubuntu 13.10 server, and configured nut appropriately. The cgi scripts are working fine, but on upsstats.cgi, the Batter, UPS Temp and Battery Runtime fields are all blank - and there are no entries for these values in the 'All data' tree. I've checked the man page for bcmxcp_usb
2006 Feb 21
3
sniffing sip password/uri/host info
Hello all, I want to sniff all these info to test a sip ip phone talking to a asterisk server. I have used tcpdump, but It just shows the UDP, length: 602 Anyway to see the sip uri. Host info? Regards, Dinesh. -------------- next part -------------- An HTML attachment was scrubbed... URL:
2016 Dec 12
3
kde failing???
greetings. centos 6.8 kde 4.3.4 toshiba satellite l4550-s5976 laptop - part 1: clock losing time first noticed time was off by 8 min, reset via F2 cl terminal. ~40 min later, off by ~2 min, reset via 'service manager' by stopping ntpd, count 20, started ntpd, within a few seconds, clock reset to correct time. ~1 hour later, noticed clock off again, considered cause to be cmos
2012 Dec 07
2
Tripp Lite SMART1000RM2U
Hi, I recently purchased a Tripp Lite SMART1000RM2U UPS (http://www.tripplite.com/en/products/model.cfm?txtSeriesID=744&txtModelID=2657) and tried to configure the NUT with tripplite_usb driver and encounter the following problems: 1. battery.charge doesn't report correct charge level when the UPS is On Batter. It just reports 0. Even though it will report 100 when on line power. 2. I
2011 Apr 11
1
24 bit flac decoding efficiency
I am trying to decode 192k/24 bit flac on 542 MHZ risk processor, and I am having problems. I seem to be right at the edge of what this processor can do. So I am wondering what functions would be canidates for assembly code optimization? Any suggestions? Or could an older version of code be a batter candidate to use? Dennis Kerrisk 720-542-8504 303-668-0736 dennis_k85 at yahoo.com
2006 May 16
1
Size of observations
Hi All I had to assure the randomness of backgammon game's two dices. I took 8,000,000 observations and found that one of the dices is not uniform distributed. I took 80,000,000 observations and found that the dice is uniform distributed. In both tests I used Pearson Chi Square test. My questions: 1. How many observations should I take? 2. How much the 80,000,000
2014 Feb 13
0
Eaton Powerware 5110 - some stats not reported
Run the driver with -DDDDD and see what variables it picks up. I have noted that with the Prestige 9 in bcmxcp, some variables are not consistent within models, and had to do some gentle remapping to get things to work correctly. - Tim On 02/12/2014 06:46 PM, Greg Vickers wrote: > Hi all, > > I've hooked up an Eaton Powerware 5110 to Ubuntu 13.10 server, and > configured nut
2014 Feb 13
2
Eaton Powerware 5110 - some stats not reported
On Feb 12, 2014, at 7:50 PM, Tim Dawson wrote: > Run the driver with -DDDDD and see what variables it picks up. I have noted that with the Prestige 9 in bcmxcp, some variables are not consistent within models, and had to do some gentle remapping to get things to work correctly. Tim, is this the issue you mentioned on 2014-02-02 with blocks 0x9 and 0x13? I'll reply to that email. > On
2020 Sep 29
5
Question about hardware failures / FSD
Hello, The UPS I am developing a driver to is able to report several flags for critical hardware conditions, like overheat, overload, inverter failure, output short etc. What should be the correct policy of operation when such a condition occurs? I think that the an UPS in such a condition is not reliable and therefore a system shutdown should be called. However, the developer's manual and
2005 May 18
1
Small office setup with Asterisk @home, IAX and analog termination
I'm setting up a small office with about 8 SIP phones. Incoming and outgoing lines will be through IAX. We would also like to use an analog line for 911. Is the TDM01B a good option for this kind of configuration? Are there gotchas I'm missing? Finally, we would like to be able to use analog fax machines in the office. Would it make more sense to purchase the TDM400 card with 1 FXO
2016 Sep 30
1
Good Bye SAMBA?!?!?
lol 60++ posts. 2016-09-29 18:30 GMT-03:00 Miguel Medalha via samba <samba at lists.samba.org>: > >> Problem is -- inotify is not recursive by default. > > Yup. That's why I've been using Watcher, a recursive incron type daemon > written in Python. > > https://github.com/splitbrain/Watcher > -- > To unsubscribe from this list go to the following URL
2013 Jan 08
1
sftp "cd" command to drive letter under cygwin
Hello. When using sftp under cygwin, a "cd d:" attempt to change to the d: drive, results in the following: sftp> cd d:/ Couldn't canonicalise: No such file or directory. It can only be done by using a cygdrive-type path: sftp> cd /cygdrive/d sftp> pwd Remote working directory: /cygdrive/d sftp> yet a local cd (lcd) works fine. "lcd d:" works, and then lpwd
2008 Apr 28
4
Samba 3.2.0-pre3 packages in Debian - version of Samba in Debian lenny
The day after Karolin announced the release of 3.2.0-pre3, the Debian packaging team was able to upload .deb packages for it in Debian *experimental*. To use them, you need to already use Debian testing or unstable, then add this to /etc/apt/sources.list: deb http://ftp.fr.debian.org/debian experimental main contrib non-free (replace "fr" by your favorite mirror country code) If you
2011 May 29
1
reshape with function(x,y)?
Hi, I'm not sure if this is impossible or if I just don't know the syntax. example: library(reshape); library(corpcor); data<-data.frame(ids=c("A","A","A","B","B","B"),rate=c(12,14,17,10,8,5),sample=c(100,80,60,50,40,45));
2008 Jul 25
3
CyberPower 550SL reports LB and OB when on line power
I am using nut 2.2.2 and I have a CyberPower CP550SL. According to the drivers list, I should be using genericups with upstype set to 7, but when I try that and when I run upsc I get: driver.name: genericups driver.parameter.LB: 04 driver.parameter.pollinterval: 2 driver.parameter.port: /dev/ups driver.parameter.upstype: 7 driver.version: 2.2.2 driver.version.internal: 1.34 ups.mfr: CyberPower
2008 Jul 25
3
CyberPower 550SL reports LB and OB when on line power
I am using nut 2.2.2 and I have a CyberPower CP550SL. According to the drivers list, I should be using genericups with upstype set to 7, but when I try that and when I run upsc I get: driver.name: genericups driver.parameter.LB: 04 driver.parameter.pollinterval: 2 driver.parameter.port: /dev/ups driver.parameter.upstype: 7 driver.version: 2.2.2 driver.version.internal: 1.34 ups.mfr: CyberPower
2020 May 11
2
[RFC] Remove AGP support from Radeon/Nouveau/TTM
On Monday, May 11, 2020, 1:17:19 PM, "Christian K?nig" wrote: > Hi guys, > Well let's face it AGP is a total headache to maintain and dead for at least 10+ years. > We have a lot of x86 specific stuff in the architecture independent > graphics memory management to get the caching right, abusing the DMA > API on multiple occasions, need to distinct between AGP and
2020 May 11
3
[RFC] Remove AGP support from Radeon/Nouveau/TTM
On Tue, 12 May 2020 at 06:28, Alex Deucher <alexdeucher at gmail.com> wrote: > > On Mon, May 11, 2020 at 4:22 PM Al Dunsmuir <al.dunsmuir at sympatico.ca> wrote: > > > > On Monday, May 11, 2020, 1:17:19 PM, "Christian K?nig" wrote: > > > Hi guys, > > > > > Well let's face it AGP is a total headache to maintain and dead for at