similar to: Problem passing a HP-DAT (USB) device to domU (fwd) (this time with outputs!)

Hello List, I'm hoping someone else out there has an Asus DSBF-DE server board, and can tell me if anything special needs to be done to get ports 5 and 6 of the onboard SATA to work under Centos 5.1 x64. I have drives on 1 through 4 that are detected and working properly, however, a drive on 5 is not detected, from what i can tell, the kernel doesn't even see phy's for ports 5 and 6.

Package: xen-hypervisor-4.1-amd64 Version: 4.1.4-3+deb7u1 Severity: important Dear Maintainer, We are having a problem on several Supermicro servers (I'll include more details on the configuration later) : when booting Linux 3.2 linux-image-3.2.0-4-amd64 (Wheezy) as a DOM0 on Xen 4.1 (xen-hypervisor-4.1-amd64 from Wheezy), the system hangs after : [ 3.716174] scsi1 : ata_piix [

Hi there, I''m running Xen 3.2.1-rc1-pre on a Ubuntu 8.0.4 server (kernel 2.6.24-19-xen). I have some network cards which are passed through to the DomUs. ''Normally'' everything works quite well. but sometimes when a DomU crashes or has to be shutdown, the pci interrupt of that DomU gets disabled in Dom0. After that happend there is no way (at least I haven''t

Dear folks, We are installing a large diskless cluster using CentOS 5.1. The hardware is pretty new - Supermicro X7DWT boards with Harpertown CPUs. Unfortunately we have some PXE-related problems described by the following scenario: 1) Set up DHCP, TFTP and NFS on a server, prepare PXE kernel and initrd - fine. 2) Start up the node using PXE for the first time - fine. 3) Reboot the node - PXE

Hi ,Guys I installed CentOS5.2-x86_64 on my Dell PowerEndger 1950 with virtualization component ,when reboot the system halted at: /////////////////////////////////////////////////////////// Red Hat nash version 5.1.19.6 usb 1-5: device not accepting address 4 ,error -110 usb 1-5: device not accepting address 5, error -110 usb 1-5: device not accepting address 6,error -110 usb 1-5: device not

I have a current RELENG_7 running on: http://www.supermicro.com/products/system/4U/7045/SYS-7045B-TR+.cfm with the -3+ IPMI card. I can interact with the BIOS, etc, but no joy once we get past the loader. Anyone have ideas? Attached is the kernel config, and the /var/run/dmesg.boot file. -- Larry Rosenman http://www.lerctr.org/~ler Phone: +1 512-248-2683

Hi, I was trying to rebuild world on a FreeBSD 10 test system, that I had just installed. ZFS root was setup. I let the installation program do all the ZFS setup and configuration. I put root on a 5 disk encrypted raidz array. Besides the installer configuring 5 times the amount of swap space I asked for (asked for 8gb, installer put 8gb on each drive, for 40gb in total.) everything was working

Hello everybody, we recently got three Dell PowerEdge servers equipped with Qlogic QLE2462 cards (dual FC 4Gbps ports) and an EMC CLARiiON CX3-40 SAN. The servers with the FC cards were successfully and extensively tested with an older SUN StorEdge T3 SAN. However, when we connect them to the CX3-40, create and mount a new partition and then do something as simple as "tar -C /san -xf

I have begun to see these messages in my morning reports: WARNING: Kernel Errors Present pciehp 0000:00:1c.0:pcie04: Link Training Error occurs ...: 146 Time(s) pciehp 0ng Error occurs ...: 1 Time(s) pcieport 0000:00:1c.0: bridge window [mem 0xd0a000000.0 failed with error -22 ...: 1 Time(s) r8168: probe of 0000:01:00.0 failed with error -22 ...: 702 Time(s) r8168:

Update.? Only a single reboot has occurred since changing defalt_vsz_limit from 384M to 512M.? It would seem that something the users are doing is causing that virtual memory size to be exceeded (possibly a mailbox search?), and when that occurs Dovecot/FreeBSD is not handling the event as smoothly as expected. Here's my dmesg for more basic info. Sep 17 11:25:39 romulus syslogd: kernel boot

Hi there, I have a question regarding PCI passthrough on the Citrix XenServer 5.6 (Xen 3.4.2). I already managed to get some soundcard passed through to a Windows guest. So I think my knowledge about that topic isn''t _that_ low. But I cannot seem to pass through a SATA/PATA controller to a Linux guest. I have some additional CD/DVD burner (PATA) attached to a SATA/PATA controller

# lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation 5520 I/O Hub to ESI Port [8086:3406] (rev 22) 00:01.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 [8086:3408] (rev 22) 00:03.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 [8086:340a] (rev 22) 00:05.0 PCI bridge [0604]: Intel Corporation 5520/X58 I/O Hub PCI

Hello, I am installing dahdi on a machine lspci 00:00.0 Host bridge: Intel Corporation 3200/3210 Chipset DRAM Controller (rev 01) 00:01.0 PCI bridge: Intel Corporation 3200/3210 Chipset Host-Primary PCI Express Bridge (rev 01) 00:06.0 PCI bridge: Intel Corporation 3210 Chipset Host-Secondary PCI Express Bridge (rev 01) 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI

Hello, I´m trying to map one network interface of a Dual-Port e1000 Server Adapter to a DomU (firewall). In Dom0 the adaper is seen with lspci as: 06:00.0 Ethernet controller: Intel Corporation 631xESB/632xESB DPT LAN Controller Copper (rev 01) 06:00.1 Ethernet controller: Intel Corporation 631xESB/632xESB DPT LAN Controller Copper (rev 01) My goal is to map only 06:00.1 to DomU so I used this

On 7/30/2016 6:56 AM, Fawzy Ibrhim wrote: > # lspci -nn > 00:00.0 Host bridge [0600]: Intel Corporation 5520 I/O Hub to ESI Port [8086:3406] (rev 22) > 00:01.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 [8086:3408] (rev 22) > 00:03.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 [8086:340a] (rev 22) >

Hi... I have a Dell Latitute with an ATA/ATAPI-5 T13 1321D and it would seem that my disk access is extremely slow. I have the latest updated kernel from RedHat 8.0 kernel 2.4.18-27.8.0. Somehow I think it is related to the UDMA stuff (shows my level of understanding). I have run hdparm and although I think I should at least udma level 5, I have at most udma2 listed. Is this a kernel

I spent a few hours upgrading one of my Xen boxes so that I''d be able to use VT-d. I bought a DQ35JO because it seemed like a sure thing. I can successfully use pciback to hide and grab devices. Specifically I am trying to pass some USB controllers to Windows. The DQ35JO/ICH9DO appears to have two independent sets of USB UHCI/EHCI controllers: 00:1a.0 USB Controller: Intel

I have one HP Proliant DL320 G5p, where for some reason, the AHCI mode is not enabled. According to server specs, it should have AHCI/NCQ capability, but ata_piix module gets loaded during bootup, not ahci module. Any ideas how to enable AHCI mode? lspci output: # lspci 00:00.0 Host bridge: Intel Corporation 3200/3210 Chipset DRAM Controller (rev 01) 00:01.0 PCI bridge: Intel Corporation

Hello, In real life I use xen 3.3.1 successfully on servers Fujitsu-Siemens RX100. Now I to see how working xen-3.4-rc3 on the same server, but unfortunately is a problem with loading a module to handle the disk (mptsas) . I use debian lenny 5.0.1 and kernel version 2.6.26-2-xen-686. Someone managed to compile 3.4 xen kernel with this version? xen:~# lspci 00:00.0 Host bridge: Intel

Sorry to duplicate my issues onto the list - I thought I had looked through this thread before and seen a different error, but apparently Adam and I are running into much the same thing. I'm seeing exactly the same "Failed to assign device to IOMMU" along with the "Device not owned by PCI Back End or pci-stub" in these scenarios. I have not gone back to previous versions,