similar to: Weird network performance behaviour?

Hello, There is a xen setup in which "brctl show" gives the following output. bridge name bridge id STP enabled interfaces eth1 8000.003048c9d4df no peth1 vif1.0 vif2.0

xenconsole fix. reference of tty->count in xencons_close() is racy. It must be protected by tty_sem semaphore like con_close() in drivers/char/vt.c -- yamahata _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel

Hi! I have a problem with my new Xen setup. I have installed Debian etch with netinstall and I''m using 2.6.18-6-xen-amd64 kernel in my dom0 and 3.0.3-0-4 version xen hypervisor. I''m using four network cards on my system and using three of them as xen bridges and dom0 is using the fourth one only for it''s own. So basicly both of my virtual servers use a network card

Hi all, I have a very strange situation, which I can''t explain. On a Core 2Quad server with 8GB RAM, we have 10 xen domU''s, as follows: vps.animalsaregreat.info login: root@zaxen01:[~]$ xm list Name ID Mem(MiB) VCPUs State Time(s) Domain-0 0 512 4 r----- 232.2 actionco.vm

Hi, I''ve set up identical (what I think) machines using SLES 10 x86_64, but a new one of those is saying frequently in /var/log/messages: kernel: bond0: received packet with own address as source address A short summary of ifconfig looks like this: bond0 Link encap:Ethernet HWaddr 00:14:4F:2A:12:9C inet addr:132.199.176.78 Bcast:132.199.255.255 Mask:255.255.0.0 eth0

Hi All, I am facing an issue regarding communicating a value from outside to a Guest OS (linux, solaris and windows) launched on Xen Server. I did went through this thread, but It was not completely clear. http://lists.xensource.com/archives/html/xen-users/2006-07/msg00473.html My question is - Is there a way in Xen, through which I can communicate a value from outside to a Guest OS (linux,

I installed 64-bit xen 3.1.0 (from xensource.com tarballs) on three new machines today, using a configuration setup that I''ve used successfully many times before. However, I encountered a new problem. These are Dell Poweredge 1950 servers, by the way. >From lspci 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) 08:00.0 Ethernet

I''ve looked everywhere for the error message I''ve posted in the title, doesn''t seem like anyone else has it (lots of missing hotplugs scripts). We''re using network-nat. ifconfig -a outputs this: eth0 Link encap:Ethernet HWaddr 00:19:99:a8:f4:5c inet addr:X.X.X.X Bcast:X.X.X.X Mask:255.255.255.255 inet6 addr: X::X:X:X:X/64 Scope:Link

Hello everyone, I have been able to get windows xp to run under a virtual machine, but i cannot get any network access. My desktop is connected to a university network, and we are only given 1 ip address. so i understand i have to use routing instead of bridging, right? i have commented the two lines for bridge and enabled routing in /etc/xen/xend-config.sxp next i inserted a line: vif

I am installed Xen 3.0 on a Fedora Core 4(2.6.12-1.1454_FC4xen0) machine. This machine is currently running one host domain: [root@]# xm list Name Id Mem(MB) CPU VCPU(s) State Time(s) Domain-0 0 128 0 1 r---- 49.1 fc4-vm1 1 63 0 1 -b--- 18.5 Following is the network configuration for Domain-0: eth0 Link

Hello. I need your help, DomU xen network diconnects randomly, how do you monitoring this? When I connect to vnc server in the hosts, DomU is running, then I open the DomU, after that guest network responds. DomU Debian 6.03 over Centos 5.7 and Xen 3.03. My network configuration: eth0 Link encap:Ethernet HWaddr 68:B5:99:78:AA:6D inet addr:192.168.5.230 Bcast:192.168.5.255

Hi, I tried this post on the Xen list first with no answer. I have 4 machines and 3 of which (all different) have no network access when booted into Xen. I tried using Fedora Core 8 and it produced the same results. Is it normal for the virbr0 interface to take an arbitrary IP? How does it decide what to use? An ifconfig when booted into Xen shows the following: eth0 Link encap:Ethernet

Hello, I''ve read the FAQ and searched the mailing list but have been unable to resolve my issue with networking in DomUs. The following things I CAN do: +SSH from within DomU to Dom0 +SSH from within DomU to all other DomUs on the same machine +SSH to other machines from within Dom0 +SSH from within DomU to other machines +SSH from other machines to Dom0 (and use the xm commands to

Hi, I have Xen 3.0.3 installed on CentOS 5.5 with 2 paravirtualized domU''s configured to use the default bridge networking and am having networking issues. If I boot the computer fresh I am able to ping dom0 and can SSH into it and start the domU''s. The following ping snippet demonstrates the problem. The first group of "Destination Host Unreachable" is while the

hi, after rebooting my host, i can''t have anymore the networking: here''s my output of /etc/init.d/networking restart Reconfiguring network interfaces...SIOCSIFADDR: No such device eth0: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device eth0: ERROR while getting interface flags: No such device Failed to bring up eth0. done. cat

Greetings! I finally got the install done for a couple of gust OSs (Win 2003 server & Suse Enterprise 10) Bothe gusts are up and running, but - no networking. My setup: Hardware - AMD Athlon 4200+, ABIT Motherboard, 4 GB of DDR2 RAM, 2 onboard GB NICs Host OS- Suse Linux Enterprise server 10 Xen - 3.0.2_09749-0.4 Config file for Win 2003 server guest: # -*- mode: python; -*-

I am posting the message below again because it did not go through last night. Help! Steve Timm -- ------------------------------------------------------------------ Steven C. Timm, Ph.D (630) 840-8525 timm@fnal.gov http://home.fnal.gov/~timm/ Fermilab Computing Division, Scientific Computing Facilities, Grid Facilities Department, FermiGrid Services Group, Assistant Group Leader.

Well where do I start...I have a domU (ubuntu) booting and appears well but I don''t have an eth0 listed at all, dom) looks good. DomU: eth0 Link encap:Ethernet HWaddr 00:06:5B:15:C5:0B inet addr:10.99.99.5 Bcast:10.99.99.7 Mask:255.255.255.248 inet6 addr: fe80::206:5bff:fe15:c50b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

xm list reveals the following information... Name Id Mem(MB) CPU State Time(s) Console Domain-0 0 315 0 r---- 2058.1 Domain-1 11 342 0 -b--- 5.2 9611 Domain-2 12 342 0 -b--- 3.9 9612 Xen seems to be working beautifully but I have not yet figured out how to get Domain-0 to ping both Domain-1 and Domain-2,

Hi, I would like to know if somebody can point me out how to configure several DomUs in a private LAN (for example 192.168.100.0/24) and one DomU with two interfaces (one - 192.168.100.0/24 and two - internet). So far I have enabled in xend-config.sxp: (network-script network-route) (vif-script vif-route) My config files have: /mnt/VM/1.cfg:vif = [''ip=192.168.1.3'']