similar to: [PATCH] fix free of event channel in blkfront

Hi All, We tested with Japanese keyboard. Then, the local keys that was not able to be input with a Japanese keyboard was found. This patch added the key that was not able to be input to the keymap. The key that cannot be input is as follows. ・Katakana ・Eisu_Toggle Signed-off-by: Takanori Kasai <kasai.takanori@jp.fujitsu.com> Signed-off-by: Junko Ichino

Hi All, I sent the patch to make blktap work with PV-on-HVM. I corrected the part that had been pointed out in the Xen community. ・All xvdN disk is looked like hdN. ・All tap disks are checked.(tap:aio, tap:sync, tap:vmdk, etc.) We cannot use blktap for the volume of the system with PV-on-HVM and are embarrassed. Could you apply this patch? Or, please give the comment to me. Signed-off-by:

Hi all, Currently we have severe problem and are struggling to investigate it. The problem is data broken. Reproduce pocess is following, 0. test FTP function between guest domain and FTP client(other PC). 1. put data from FTP client to guest domain. 2. get data from guest domain to FTP client. 3. compare put data and get data on FTP client. 4. repeat process from step1 to step3.

Hi All, My name is Takanori Kasai. This is a first time to send mail. I found the key that was not able to be input to HVM Domain (VTx and VTi Domain) through VNC Server with Japanese keyboard. I think that it is a cause by lack of some keys in Japanese keymap and the key symbol table in qemu-dm. This patch is addition of the keys for Japanese keyboard. My best regards. - Takanori Kasai

Hi All, The interface of the evtchn has been changed as follows. ・xen-unstable.hg : cs13198 [PV-ON-HVM] Update evtchn interface to match new PV Linux interfaces. ・xen-unstable.hg : cs13197 [LINUX] Extend the event-channel interfaces to provide helper methods However, the following errors occur if pv-on-hvm is done in insmod. This patch corrected this issue. --- # insmod xen-vbd.ko

Hi All, It is natural that there is quit command in original QEMU. However, I don''t think that the HVM domain on Xen is necessary. Because there is a possibility of shutting down GuestOS due to the mistake. I think that I should prohibit the quit command of qemu-dm. Thanks -- Takanori Kasai _______________________________________________ Xen-devel mailing list

Hi All, We contributed the problem when CD-ROM was changed as follows. There was especially no comment though we confirmed the correction method. Therefore, the patch that corrects these problems is contributed. Signed-off-by: Takanori Kasai <kasai.takanori@jp.fujitsu.com> Best Regards, --- Takanori Kasai ----- Original Message ----- From: "Kasai Takanori"

Hi I have a couple of questions: 1. How do I exist from a domU console back to dom0 console (after issuing xm console [domU])? 2. How do I setup a dom0/domU in order to get a tty login? TIA Paolo _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

Changeset 10742:3e07ec30c445 made it possible to switch to the QEMU monitor terminal when using the VNC display protocol. Unfortunately the VNC key handling is rather crazy, so even if you have the shift key pressed, a VNC client will send a lowercase letter, expecting the server to interpret the state of the shift key as desired. Normally in HVM guests, the guest OS does this interpretation

I am enclosing the patch I have been working on. I have tested this on sles9 (2.6.5) and RHEL 4 (2.6.9). The patch applies cleanly on ChangeSet 11635. This patch was cleaned up based on Ian''s and DOI''s work. Signed-off-by: K. Y. Srinivasan (ksrinivasan@novell.com) _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com

Hello * i have to rename a lot of variables, and, given that they have regular name constructs, I would like to use regexps. Here's a dump of my head(names(df)) varnames <- c("id.quest", "txt.1.3", "col1.1.3", "col2.1.3", "col3.1.3", "col4.1.3", "col5.1.3", "txt.2.3", "col1.2.3",

Hello, I am desperately trying to get pci-passthrough to working. I want to pass a tg3 nic to domU. when booting domU I get a lot of messages: pcifront pci-0: pciback not responding!!! in domU, "ifconfig eth... adress up" hangs for 2 minutes, finally ifconfig -a shows a correct setting with no data transmitted rx/tx The IP Adress is being assigned, but there is no data transmission

Hi All, I sent the patch to allow blktap to be able to booted as system bolume for PV-on-HVM. However, there was a problem that hdN and xvdN were not able to be specified at the same time. I made the patch to correct it as follows. - Whether hdN is defined first is checked. - If hdN is defined, xvdN is not replaced with hdN. Signed-off-by: Takanori Kasai <kasai.takanori@jp.fujitsu.com>

Hi, I''m trying to figure out how XEN decides which VNC port a particular VM will associate with. From what little there is in the documentation, it indicates that XEN will choose 5900+DomainID. From experience, this doesn''e seem to happen. When I start a guest domain, and do "xm list" its domainID shows as "22", however, when I netstat -a , it shows listening

Hi, I'm running samba-3.0.22, linux-kernel-2.6.16 and I'm having troubles with trusted domains. How can I find the suitable DC for each domain? Could be a resolution issue? Bellow my smb.conf and some tests. [global] workgroup = DOM1 netbios name = localhost server string = LOCALHOST Server security = ads realm = MYDOMAINCONTROLLERREALM

Hi, This patch intends to accurate vcpu weighting for CPU intensive job. The reason of this problem is that vcpu round-robin queue blocks large weight vcpus by small weight vcpus. For example, we assume following case on 2pcpu environment. (with 4domains (each domain has 2vcpus)) dom1 vcpu0,1 w128 credit 4 dom2 vcpu0,1 w128 credit 4 dom3 vcpu0,1 w256 credit 8 dom4 vcpu0,1 w512 credit 15

I have noticed the following behavior when testing out Samba 3.0.1 on RH9 with ldap authentication. Linux Samba V3.0.1 set up as PDC for domain DOM1 has a user test1. Two NT4 domains DOM2 and DOM3 also have a user called test1 with the same password as the user in DOM1 (all three users have the same username and password). All servers are on the same local subnet. When user1 does a logon to

Hi, If i take a snapshot of a qcow2 image backed domain via virsh snapshot-create domainID and I shutdown the machine (and probably destroy the domain if virsh list still shows it running), and then undeinfed the domain will that snapshot still exist and be active when I define and start the domain back up? --- Thanks, Yitao(依涛 姜) jiangyt.github.io

Further to my messages back in May I have at last got round to trying to get my DomU to recognise USB devices. I am using Xen 4.6 with CentOS kernel 3.18.34-20.el7.x86_64. I have to manually make the port available before creating the DomU by issuing the command: xl pci-assignable-add 00:1a.0 otherwise nothing shows in: xl pci-assignable-list I have added this to my .cfg file as per the

Hello, My name is Fermín Galán. I have started recently to use Xen (so please forgive me in advance if I''m too "newbie" :) and I''m facing my first problems... I''m trying to create a domU, but I''m getting an error: tornado:~# xm create test.cfg -c Using config file "/etc/xen/test.cfg". Error: Device 2049 (vbd) could not be connected.