similar to: ISDN card in xenu domain

Hello, After searching the archives, I''ve found only two messages regarding this case, but there were no solution. I have a similar problem, so I try to ask here. I have twi HFC chipset ISDN cards in my pc: 0000:00:0d.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02) Subsystem: Cologne Chip Designs GmbH ISDN Board Flags: bus

Hi all, did somebody successfuly export ISDN Cards to DomU? I want to have 2 ISDN Cards in DomU (for Asterisk with mISDN) lspci -vt -[0000:00]-+-00.0 nVidia Corporation MCP55 Memory Controller +-01.0 nVidia Corporation MCP55 LPC Bridge ... +-05.1 nVidia Corporation MCP55 SATA Controller +-06.0-[0000:01]--+-00.0 Cologne Chip Designs GmbH ISDN

Hi, Bristuff works great with HFC card... your compilation problem may come from your kernel configuration... You should check this doc, at least, for the redhat config : http://www.automated.it/guidetoasterisk.htm Then, installation of Bristuff works like as charm ! Bye David Masure -----Message d'origine----- De : vdasilva [mailto:aquamoon@wol.co.za] Envoy? : mardi 28 juin 2005 09:01

Hello everybody! After checking the complete wiki and the mailinglist archives I still haven't really found out why the following constellation does not work. We have an asterisk-System with some SIP-Phones and an old ISA Fritz-ISDN-Card used with i4l. The whole system is integrated in out (ISDN-)PBX for testing. The ISDN-Card is properly configured, as we are able to phone out, receive

Hello I have asterisk running in Red Hat 9 with a cheap HFC card on i4l. I have choppy sound problems sometimes, and echo problems often. I am using a 2 port Grandstream ATA, Grandstream BT and a Grandstream GPX-2000 I read that changing to BriStuff will fix the echo problems, but have also read other users say that the only way they solved the echo/choppy sound problems was using a Fritz ISDN

Hello, I'm a newbie trying to figure out how to install an ISDN Card. I downloaded the latest Asterisk iso and did install it (actually version 1.3). ISDN Card details: Eicon Diva Server BRI-2M/-2F I did listen something that capi 2.0 is needed and some drivers etc. but I can't figure out how it works. Has some of you maybe experience in that? Or does someone of you know an easy to

There is no CONFIG_SCSI to enable in xenU. Is there any reason for this? I want to try out iSCSI and obviously it needs scsi support. Or would I be better doing it in dom0 and exporting it? thanks James

i read that quite all of you are using the driver for the isdn that you are using is the digium... i use I4L and i got a problem with some call through normal PBX, can someone tell me where i can download the digium drivers for the ISDN card? i didn't find it... but i'd like to try if is a driver issue... (i use a digium isdn card...) thanks a lot, Angelo

I have an asterisk installation connected to 2 isdn lines via an AVM C2 card. modules seems to load well, lsmod gives : c4 19588 4 b1 24192 1 c4 capidrv 28468 2 isdn 134604 9 capidrv slhc 7552 1 isdn capi 18112 4 capifs 6024 2 capi kernelcapi 46112 4

Hi, I'm setting up an asterisk server with this hardware configuration: AMD Athlon 1000 Mhz 256 MB ram 3ware ATA raid controller 2 * Ethernet controller 2 * ISDN HFC controller One ethernet controller is connected directly to the internet (public IP) One ethernet controller is connected to the internal lan One ISDN controller is connected to the public telephone network One ISDN controller

Hi! If I install a CAPI-compatible ISDN-card in my server, will that: a) enable me to connect that server to the public phone net b) allow me to connect an ISDN phone to the server and use it as a SIP-phone c) all of the above? Regards, Evert

Hi everybody I have installed a TrixBox with Asterisk 1.2.14 and relative upgreaded software. I Bristuffed it with last version of bristuff to use a Hemlet PCI ISDN CARD in a normal Italian EUROISDN installation. The * works fine except for the ISDN CARD. It is always Channel D down, but if a Call comes in, it works perfectly for some time, both inbound and outbound. It prompts Channel D UP!

Hi guys, I'trying to setup Asterisk with an AVM Fritz PCI ISDN card with no success. I have an IP phone from Micronet and I want to receive and place calls over ISDN. But I'm not sure if I need the binary CAPI from AVM or isdn4linux. I've tryed with redhat 9 and with Suse 8.2. Cold someone help me? Thank you very much.

Hi All, Has anyone had experiences with Asterisk and ISDN Gateways or cards? I am looking to setup a home phone system using asterisk and am looking to convert my two existing no's to a single isdn2e line. I was wandering if anyone could recommend which is better to use with asterisk - ISDN Card or gateway? also which brands are best with linux/asterisk? I have used eicon BRI cards for

Hi All, I currently run asterisk in our office (in Japan) and use a cisco PRI gateway for connection to the PSTN. I would like to setup some more systems for our smaller offices (in Japan) that would use BRI and preferably using a PCI card in the asterisk box and not a seperate Cisco gateway (expensive). HOWEVER, Japan has this INS64 protocol for their BRI lines and im not sure what cards

Yes, i know that there are many ISDN card on the market. But when i spend money for ISDN card, i prefer to be Digiums, to get all support and help Asterisk :).

Hello to all, I'm trying to build a PBX using Asterisk. I have a single BRI ISDN line and I need to connect 4 internal normal phones and a couple of softphones on PC. I have bought a single port Billion S0 card and a TDM400 with 4 FXS modules for the intenal phones. ISDN lines here in Greece terminate to an NT1 terminal called NetMod

Hello I want to setup an Asterisk in several offices with 4 BRI ISDN. I am looking for recommendations on hardware. Criteria would be ease of setup, reliability and cost. The Eicon 4 BRI cards seem fairly pricey. Shame Digium don't do a ISDN BRI card. Angus -------------- next part -------------- An HTML attachment was scrubbed... URL:

I'm trying to use an hfc based pci card with asterisk but every call fails falling in the congestion extension. exten => _0.,1,Dial(${TRUNK}:${EXTEN:${TRUNKMSD}}||tr) exten => _0.,2,Congestion Looking in the syslog i can see: isdn: HiSax,ch0 cause: E001B it seems that this is a terrible error when arrives... hard to tell what is the cause. Also terrible is finding a lot of material

Hello, I'm looking for an ISDN BRI-U interface for use in the US. I'm primarily interested in using the BRI as a trunking interface into the PSTN with Asterisk. Naturally, cheaper is better. I currently use a Nortel Norstar system with BRI-U trunks, and really like the digital PSTN interface. Would really like to replace the whole mess with Asterisk but want to keep the ISDN trunks.