similar to: SMART problems with AOC-SAT2-MV8 / marvell88sx driver

Hey all, I''m not sure if this is a ZFS bug or a hardware issue I''m having - any pointers would be great! Following contents include: - high-level info about my system - my first thought to debugging this - stack trace - format output - zpool status output - dmesg output High-Level Info About My System --------------------------------------------- - fresh

Hello zfs-discuss, One of a disk started to behave strangely. Apr 11 16:07:42 thumper-9.srv sata: [ID 801593 kern.notice] NOTICE: /pci at 1,0/pci1022,7458 at 3/pci11ab,11ab at 1: Apr 11 16:07:42 thumper-9.srv port 6: device reset Apr 11 16:07:42 thumper-9.srv scsi: [ID 107833 kern.warning] WARNING: /pci at 1,0/pci1022,7458 at 3/pci11ab,11ab at 1/disk at 6,0 (sd27): Apr 11 16:07:42 thumper-9.srv

After applying 125205-07 on two X4500 machines running Sol10U4 and removing "set sata:sata_func_enable = 0x5" from /etc/system to re-enable NCQ, I am again observing drive disconnect error messages. This in spite of the patch description which claims multiple fixes in this area: 6587133 repeated DMA command timeouts and device resets on x4500 6538627 x4500 message logs contain multiple

I have a supermicro AOC-SAT2-MV8 and am having some issues getting drives to work. From what I can tell, my cables are to long to use with SATA2. I got some drives to work by jumpering them down to sata1, but other drives I can''t jumper without opening the case and voiding the drive warranty. Does anyone know if there is a system setting to drop it back to SATA1? I use zfs on a raid2 if

Hi all, I''m getting a very strange problem with a recent OpenSolaris b134 install. System is: Supermicro X5DP8-G2 BIOS 1.6a 2x Supermicro AOC-SAT2-MV8 1.0b 11 Seagate Barracuda 1TB ES.2 ST31000340NS drives If I have any of the 11 1TB Seagate drives plugged into the controller, the AOC-SAT2-MV8 BIOS appears to detect them just fine, but I get the following problems: 1. Grub takes a

Every day we see pause times of sometime 60 seconds to read 1K of a file for local reads as well as NFS in a test setup. We have a x4500 setup as a single 4*( raid2z 9 + 2)+2 spare pool and have the files system mounted over v5 krb5 NFS and accessed directly. The pool is a 20TB pool and is using . There are three filesystems, backup, test and home. Test has about 20 million files and uses 4TB.

Bouncing a thread from the device drivers list: http://opensolaris.org/jive/thread.jspa?messageID=357176 Does anybody know if OpenSolaris will support this new Supermicro card, based on the Marvell 88SE6480 chipset? It''s a true PCI Express 8 port JBOD SAS/SATA controller with pricing apparently around $125. If it works with OpenSolaris it sounds pretty much perfect. --------------

Hello, I''ve been using Nexentastore Community Edition with no issues now for a while now, however last week I was going to rebuild a different system so I started to copy all the data off that to my to a raidz2 volume on me CE system. This was going fine until I noticed that they copy was stalled, as well as the entire system was non-responsive. I let it sit for several hours with no

Hello All, I have an issue where I have two SATA cards with 5 drives each in one zfs pool. The issue is one of the devices has been intermittently failing. The problem is that the entire box seems to lock up on occasion when this happens. I currently have the SATA cable to that device disconnected in the hopes that the box will at least stay up for now. This is a new build that I am

Hello, I am not sure if I am posting in the correct forum, but it seems somewhat zfs related, so I thought I''d share it. While the machine was idle, I started a scrub. Around the time the scrubbing was supposed to be finished, the machine panicked. This might be related to the ''metadata corruption'' that happened earlier to me. Here is the log, any ideas? Oct 24

Hi, all, I think I''m missing a concept with import and export. I''m working on installing a Nexenta b134 system under Xen, and I have to run the installer under hvm mode, then I''m trying to get it back up under pv mode. In that process the controller names change, and that''s where I''m getting tripped up. I do a successful install, then I boot OK,

I''ve installed Open Solaris 2009.06 on a machine with 5 identical 1TB wd green drives to create a ZFS nas. The intended install is one drive dedicated to the OS and the remaining 4 drives in a raidz1 configuration. The install is working fine, but creating the raidz1 pool and rebooting is causing the machine report "Cannot find active partition" upon reboot. Below is command

i''ve got a little zpool with a naughty raidz vdev that won''t take a replacement that as far as i can tell should be adequate. a history: this could well be some bizarro edge case, as the pool doesn''t have the cleanest lineage. initial creation happened on NexentaCP inside vmware in linux. i had given the virtual machine raw device access to 4 500gb drives and 1 ~200gb

Hello! I''am setup zfs / cifs home storage server, end now have low performance with play movie stored on this zfs from windows client. server hardware is not new , but n windows it perfomance was normal. CPU is AMD Athlon Burton Thunderbird 2500, runing on 1,7GHz, 1024 RAM and storage: usb c4t0d0 ST332062-0A-3.AA-298.09GB /pci at 0,0/pci1458,5004 at 2,2/cdrom at 1/disk at

I made a bad judgment and now my raidz pool is corrupted. I have a raidz pool running on Opensolaris b85. I wanted to try out freenas 0.7 and tried to add my pool to freenas. After adding the zfs disk, vdev and pool. I decided to back out and went back to opensolaris. Now my raidz pool will not mount and got the following errors. Hope someone expert can help me recover from this error.

Hi all, Please can you help with my ZFS troubles: I currently have 3 x 400 GB Seagate NL35''s and a 500 GB Samsung Spinpoint in a RAIDZ array that I wish to expand by systematically replacing each drive with a 750 GB Western Digital Caviar. After failing miserably, I''d like to start from scratch again if possible. When I last tried, the replace command hung for an age, network

I''m not sure exactly what happened with my box here, but something caused a hiccup on multiple sata disks... May 9 16:40:33 sol scsi: [ID 107833 kern.warning] WARNING: /pci at 0,0/pci10de,5c at 9/pci-ide at a/ide at 0 (ata6): May 9 16:47:43 sol scsi: [ID 107833 kern.warning] WARNING: /pci at 0,0/pci-ide at 7/ide at 1 (ata3): May 9 16:47:43 sol timeout: abort request, target=0

I have a 1.5TB Western Digital hard disk (WD15EADS-00R6B0) on my CentOS-5.7 server, which has become incredibly slow for some operations, eg rsync, BackupPC archive, e2fsck, although it seems to work fine for ordinary file operations, and "smartctl -a /dev/sdb" does not report any errors. For example, running "e2fsck -p /dev/sdb5" on a 250GB partition on this disk took over 24

Author: lclee Repository: /hg/zfs-crypto/gate Revision: c80632cae25a4c92285f9e6434b64aa3f3aa6b79 Log message: 4855218 sparc: Need EFI label support on IDE 6275431 x86: Need EFI label support on IDE 6340778 cmlb: common disk label code 6326547 format: converting EFI to VTOC, fdisk info is taken from a random disk 6335611 format: Need to warn users that data will be lost when converting to and from

Hi Host: VirtualBox 2.1.0 (WinXP SP3) Guest: OSol 5.11snv_101b IDE Primary Master: 10 GB, rpool IDE Primary Slave: 10 GB, empty format output: AVAILABLE DISK SELECTIONS: 0. c3d0 <DEFAULT cyl 1302 alt 2 hd 255 sec 63> /pci0,0/pci-ide at 1,1/ide at 0/cmdk at 0,0 1. c3d1 <drive unknown> /pci0,0/pci-ide at 1,1/ide at 0/cmdk at 1,0 # ls