similar to: [XCP] - XCP -> HCL

Hi everyone, How many cores should show on command “top”? We have a 24 cores machine with XCP, we can see 24 cores show on XenCenter and xentop, But when use “top” and “cat /proc/cupinfo”, it only show 4 cores, Is this right? ----------------------------------------------------------------------- 黃獻輝（Hunag Hsien Hui） 中華電信研究所網路維運研究室 TEL: 03-4244997 Mobile: 0928-752495

Hello Everyone, I am new with XCP. I''ve setup several hosts with* XCP 1.0* and manage it through XenCenter and command console. Each host has two NICs, one (xenbr0) connected to a physical switch for Internet (said sw1), the other (xenbr3) connected to a physical switch for internal network (said sw2). I am trying to setup VMs and VLANs on xenbr3. I created a virtual bridge by

Hi, I am new to citrix xen server. I have sucesfully installed citrix xen server 5.6.1 Fp1(free version) on my system. and through xencenter I have connected citrix xenserver and created vm (centos 5.5 32 bit), Installed Xen-tools in centos. My xenserver and xen vm ip details are below Xenserver Ip address - 192.168.1.5 Netmask - 255.255.255.0 Gateway - 192.168.1.1 which is my xencenter

Hi guys, I am testing out some FC storage in my XCP environment but I''m a bit confused on the right way to proceed. XCP actually sees the cards "under hardware in xsconsole". I made a lv available to the XCP box I''m testing on but both fdisk -l and via the XCP cli and ui the lv isn''t there. As I understand it from the documents I''ve read, you

Hi All, I want to test REMUS over XEN, I would like to know the basic steps to be followed . I have installed xen4.1 on debian and i didn''t find any command related to remus, is there any steps which i have to carry out? _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

Hi, all, Is the Xen currently compatible with the InfiniBand? I found some information about the Smart I/O module, but it was posted in 2006. Is the module still maintained? Or, are there any up-to-date alternatives for that? Many thanks, Chiu _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

Hai, I am using dell insprion 580 machine for xen installation and dom0 configuation. I compiled xen source code and configured the kernal. Grub entry given below menuentry ''Xen 4.0.0-rc8 / Ubuntu 10.4 kernel 2.6.32.25 pvops'' { insmod ext2 set root=''(hd0,3)'' multiboot (hd0,3)/boot/xen-4.0.0-rc8.gz module (hd0,3)/boot/vmlinuz-2.6.32.25 dummy=dummy

Hai, I am using dell insprion 580 machine for xen installation and dom0 configuation. I compiled xen source code and configured the kernal. Grub entry given below menuentry ''Xen 4.0.0-rc8 / Ubuntu 10.4 kernel 2.6.32.25 pvops'' { insmod ext2 set root=''(hd0,3)'' multiboot (hd0,3)/boot/xen-4.0.0-rc8.gz module (hd0,3)/boot/vmlinuz-2.6.32.25 dummy=dummy

On Wed, May 25, 2011 at 12:41 AM, JAMES BOND 123 007 <james123007@gmail.com> wrote: > Hi , > I saw your thread post at > http://web.archiveorange.com/archive/v/ZvO4jnaavtTfcyqnHoRX > , about problems with XEN 4.0 installation. > I have the same problem and my machine is similar to yours( HP Proliant > DL380G6, 4GB-RAM) This question is better asked on the xen-users list.

Hello, I am using XCP 1.0 and am accessing it with XenCenter. I have three NIC''s and I have bonded two of them through the XenCenter frontend. I then create a VLAN using XenCenter and attach it to the bond0. I create a VM and create its NIC to use VLAN 10, which it does and when the VM boots the NIC shows Active inside of XenCenter. When I look at the XCP host it shows VLAN 10 as an

Hello, I have a Gentoo Linux guest, which was working very well with the past xm tool stack. Since the migration to xen-4.1.1 and to the new xl tool stack, I have a problem for the IP assignation. Actually, when dhcpcd starts at boot time the IP address is not correctly assigned. This also happens if I perform "dhcpcd eth0" once I''ve accessed to the guest shell. I

Does Xen Cloud Platform (XCP) support the notion of a driver domain? I can assign a VIF to a domain, but it seems that I can only attach that VIF to a network. What I''d like to do is attach the front-end VIF in one domain to a backend running in another domain. The second domain will control the physical interface (via PCI passthrough). This use case is easily supported using Xen +

Hi List, is it possible with the virt-manager to choose a drbd device? Example: 9:testsever Connected Primary/Secondary UpToDate/UpToDate C is running on /dev/sda9 but I can´t use it as a drive. (syntax?) Best, Mike _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

So Working on CEntOS 5 I am trying to sett up Xen with 2 bridges, one that connects dom0 and most of the domU to the physical card and the out to the network. Got that figured out no problem, now i want to have a second bridge that runs a local network for all the doms that doesn''t connect to the network. With code I have found used in multiple places I can easily get 2 bridges, and

Hi guys, I upgraded my home server to check out XCP 1.0 but i have a big problem. After the upgrade my network just died. I see the card, it''s listed as xenbr0 but there is no network acces/connection going over it. A ping to or from the server results in nothing. When i check out the configure managment interface settings i see the NIC, and it states connected. But there is no way to

Dear all, How to make XCP cannot management by XenCenter? We have an environment about 10 XCP host, and provide about 50 vm for users, We notice that some users want to use XenCenter to connect the XCP host, even they don’t have password, so we want to make XCP cannot use XenCenter and only for console management, is it possible? Sorry for the strange question,

Hi all, I follow instructions(http://wiki.xensource.com/xenwiki/XenParavirtOps) to build XEN and dom0 kernel. Building XEN has no problem, but there is an error which I cannot solve to build dom0 kernel. The brief instructions for building dom0 are get linux-2.6-xen code from git and make ARCH=x86_64 menuconfig, finally generate kernel.deb. (I did every step exactly as the web page says)

Recently I installed Xen on my computer.But there are some problems during the starting time. The /var/log/xen/xend.log is follows: [2011-06-10 14:24:36 1395] DEBUG (XendDomainInfo:1794) Storing domain details: {''cpu/3/availability'': ''online'', ''description'': '''', ''console/limit'': ''1048576'',

I think the title says it all :) I got far enough along in the Xen documentation that the documentation recommended me to start using XenCenter to manage the server. Why am I being asked by XenCenter to register my XCP 1.0 server? I know it''s similar, but it''s not a Citrix XenServer... ;) >From what I can gather, XCP is open source freeware...correct me if I''m