similar to: [Xen-API] Frequent I/O error of HTTP server and memory error on XenServer5.6 FP1

Hello, I am using XCP 1.0 and am accessing it with XenCenter. I have three NIC''s and I have bonded two of them through the XenCenter frontend. I then create a VLAN using XenCenter and attach it to the bond0. I create a VM and create its NIC to use VLAN 10, which it does and when the VM boots the NIC shows Active inside of XenCenter. When I look at the XCP host it shows VLAN 10 as an

Hello Everyone, I am new with XCP. I''ve setup several hosts with* XCP 1.0* and manage it through XenCenter and command console. Each host has two NICs, one (xenbr0) connected to a physical switch for Internet (said sw1), the other (xenbr3) connected to a physical switch for internal network (said sw2). I am trying to setup VMs and VLANs on xenbr3. I created a virtual bridge by

Hi, In XenServer5.6 FP1 beta, I have switched default bridge to open vswitch, I wonder how to use "xe tunnel-create" to create a GRE tunnel. my commands: xe tunnel-create pif-uuid=eth0_uuid network-uuid=network_created_by_xe_network_create then I got an uuid which is "access-PIF" of output from "xe tunnel-list". what should I do next? how to set remote_ip

Hi, I am using Xen Center5.6 FP1 since last 8 months and it was working fine since last few weeks, when i observed that suddenly all new Xen VMs started showing me sda or hda disks as xvhd. This is observed when i try to create any new Xen VM on my XenCenter5.6FP1. All my earlier Xen VMs are still showing hda or sda but when i try to upgrade the respective VMs say from SLES11GA to SLES11 SP1, it

Hi, I am using Xen Center5.6 FP1 since last 8 months and it was working fine since last few weeks, when i observed that suddenly all new Xen VMs started showing me sda or hda disks as xvhd. This is observed when i try to create any new Xen VM on my XenCenter5.6FP1. All my earlier Xen VMs are still showing hda or sda but when i try to upgrade the respective VMs say from SLES11GA to SLES11 SP1, it

I am able to start kick off windows/linux installs on a new vm but then find the installation can''t read from the dvd-rom....xe cd-list reports the dvd-rom as scsi? I am using xcp 1 beta and xencenter fp1. Any help would be appreciated. Thanks, Chris _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com

Hi All, I tried again with XAPI on Debian last night and this time things went far smoother... I managed to boot into the Xen kernel, xe is working and the XAPI daemon appears to be running. However, I am having trouble connecting to XAPI from XenCenter... it just says the connection was refused without any meaningful errors and nothing in the logs on either side. I can ping the Xen machine from

Dear all, How to make XCP cannot management by XenCenter? We have an environment about 10 XCP host, and provide about 50 vm for users, We notice that some users want to use XenCenter to connect the XCP host, even they don’t have password, so we want to make XCP cannot use XenCenter and only for console management, is it possible? Sorry for the strange question,

Hi all, today i tried to enable HA on xcp 1.6 but when i enable it through xencenter I received the following error in xensource.log: Dec 5 17:56:26 xcp1 xapi: [ info|xcp1|490661|Async.pool.enable_ha R:9119ce88ffcb|xapi_ha] Using statefile: /etc/xensource/static-vdis/0/disk Dec 5 17:56:26 xcp1 xapi: [debug|xcp1|490661|Async.pool.enable_ha R:9119ce88ffcb|xapi_ha]

Hi, I am new to citrix xen server. I have sucesfully installed citrix xen server 5.6.1 Fp1(free version) on my system. and through xencenter I have connected citrix xenserver and created vm (centos 5.5 32 bit), Installed Xen-tools in centos. My xenserver and xen vm ip details are below Xenserver Ip address - 192.168.1.5 Netmask - 255.255.255.0 Gateway - 192.168.1.1 which is my xencenter

New build with Ubuntu 13.04 and Xen 4.2. Installed XCP-XAPI as the plan was to use XenCenter to manage the installation. I pretty much followed this guide here: https://help.ubuntu.com/community/Setting%20up%20Xen%20and%20XAPI%20(XenAPI)%20on%20Ubuntu%20Server%2012.04%20LTS%20and%20Managing%20it%20With%20Citrix%20XenCenter%20or%20OpenXenManager With a few changes for things that have been fixed

Hi, I have installed XCP 0.5 on the HP Server. To create VM''s i installed Xencenter V5.6.0(Build 31188). Adding the server is successful but after that it get the below error. "The version of Xencenter is out of date and cannot connect to "hostname" " Please also check the attached log & let me know any possiblity to connect from Xencenter client. -- Regards,

Hi all, I''ve got XCP 1.0 up and running nicely and would like to use it in production. However I''m struggling with the concept of bandwidth management. It seems like such a common problem that everyone must have, but I can''t find any clear direction in which to go. The dedicated host I am using (Hetzner) gives me a 5TB monthly bandwidth quota which needs to be shared

XCP Users: As many of you are aware, there are several open source products available for everyone to use when working with XCP. I would like to get some feedback on the various tools to get a feeling on how people are using XCP and these tools. Here are the tools that I am aware of (please respond if you are using another tool): * OpenXenManager -

Thanks for all the help... XVP seems quite high on requirements. Like it needs an SMTP server set up. I''m not sure I like that. I found a tool called BixData, it''s proprietary but with a free license for a limited number of managed servers. Being a fully fledged cloud management system, it''s true overkill for me and my 3-4 virtual machines, but at least it seems quite

I have Kronos setup fine. I have installed open-iscsi and setup the system as an initiator. However, I cannot seem to get xapi to allow me to setup the target as an SR. I was trying to use XenCenter but go nowhere. So I tried adding it manually and here is what I got: xe sr-create host-uuid=466aac75-c86a-496f-90e8-2a9925a9e9f7 content-type=user \ > name-label="Shared LVM over iSCSI

Hi all, Using XenServer with a RHEL6 beta VM, I have sar installed on the hypervisor and VM. If I do a ''md5sum < /dev/urandom'' to spike CPU usage on the VM, I see the indication on the XenCenter performance graph on CPU 0. It does increase quickly. Neither sar output gives any sort of indication that the CPU is being loaded. This VM is pinned to both processor 0 and 1

I just noticed OpenXenCenter (aka OpenXenManager) that is an open source replacement for Citrix's XenCenter. This tool works with XenServer. But as per the blog entry: http://blog.xen.org/index.php/2010/02/09/xen-cloud-platform-installation/ it is also supposed to work with Xen Cloud Platform. XCP is licensed GPL2 and is a combination of multiple packages. Has the team looked at the

Hi everyone! I have 2 hosts + 1 ISCSI device. I want to create a shared storage repository and both hosts use together. I wont use NFS. prepared sr: xe sr-create host-uuid=xxx content-type=user name-label=NAS1 shared=true type=iscsi device-config:target=xxxx device-config:targetIQN=xxxx hosts see the iscsi device: scsi4 : iSCSI Initiator over TCP/IP scsi 4:0:0:0: Direct-Access NAS

Hi, everyone. I''m Guilherme Suzuki (brazillian, by the way) and really interested in xen-vga-passthru. Lately, I bought a brand new Saphire HD 7950 (OC Boost) because I saw in a wiki somewhere that users have been able to passthru these VGA devices to domU (win7, win-xp and so on). But, after I installed it, I executed *lspci -vv* to check if FLR in DevCap was present (which