similar to: Problem with bridged network

I''m trying to build out a test cloud using XCP 1.0.0 beta with 3 machines of 18 cores total (Phenom II 1090s). I''ve built three machines, installed XCP 1.0.0 beta on them and they all three have the same problem - the Realtek network cards don''t work. The following is the output from lspci 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI

Hi, I''ve set up identical (what I think) machines using SLES 10 x86_64, but a new one of those is saying frequently in /var/log/messages: kernel: bond0: received packet with own address as source address A short summary of ifconfig looks like this: bond0 Link encap:Ethernet HWaddr 00:14:4F:2A:12:9C inet addr:132.199.176.78 Bcast:132.199.255.255 Mask:255.255.0.0 eth0

Hi! I have a problem with my new Xen setup. I have installed Debian etch with netinstall and I''m using 2.6.18-6-xen-amd64 kernel in my dom0 and 3.0.3-0-4 version xen hypervisor. I''m using four network cards on my system and using three of them as xen bridges and dom0 is using the fourth one only for it''s own. So basicly both of my virtual servers use a network card

Hi, I have a strange problem with my networking setup. I read all forums around the world where people had similar problems, but couldn''t find a solution. I have an Attansic L1 gigeth chip on my mainboard. This chip works OK in stock Ubuntu Gutsy (development) 2.6.22-9-generic kernel. When I boot into Xen, and after the bridge is created, the network stops working. Some info: - If I

Hi, I''ve installed xen 3.0.3 from packages (xen-linux-system) on a debian etch, and i''ve configured it with network-bridge script in the default way (netdev=eth0, bridge=xenbr0, etc...) which is ok for me. the problem I have: I cannot ping any outer machine from dom0 (nor any outer machine can ping me). It gives me a "Destination Host Unreachable" message that

I have an odd problem. I am running an ubuntu 10.04 domu that I got from stacklet on my centos 5.5/xen4.0.1 dom0. The problem is that even sitting idle the domu has a 1.05 load with init taking up 99% of that. I have searched around but have not found what is causing the issue. I thought I remembered this being mentioned on the list before but could not find it either. My domu.cfg is as

Hello everybody, Here again with a Xenbr0 bridge problem I''m a Gentoo user, xen-sources-2.6.34 and I always used the bridge from eth0 to xenbr0. Here''s what I get at boot time: * Bringing up interface eth0 * null [...] * Starting Xen control daemon ... And the bridge doesn''t come up. The normal behaviour should be that the Xenbr0 bridge comes up automatically, but

xenconsole fix. reference of tty->count in xencons_close() is racy. It must be protected by tty_sem semaphore like con_close() in drivers/char/vt.c -- yamahata _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel

Hi, I have a new xen hosting platform. I have given the bridge a static IP which I can ping/ssh to etc, when I create a new vm all works well apart from the networking. If I give DomU a static IP I can''t ping out from the box, Dom0 can''t ping the vm. I''m suspecting it just isn''t seeing the bridge but am unsure where to start looking. This is a very standard

Hi, I have Xen 3.0.3 installed on CentOS 5.5 with 2 paravirtualized domU''s configured to use the default bridge networking and am having networking issues. If I boot the computer fresh I am able to ping dom0 and can SSH into it and start the domU''s. The following ping snippet demonstrates the problem. The first group of "Destination Host Unreachable" is while the

Hi, I''m trying to set up networking on a new machine. I''m not getting any networking from the domU''s I notice that I have two bridges being created: xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 RX packets:3024 errors:0 dropped:0

hi, after rebooting my host, i can''t have anymore the networking: here''s my output of /etc/init.d/networking restart Reconfiguring network interfaces...SIOCSIFADDR: No such device eth0: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device eth0: ERROR while getting interface flags: No such device Failed to bring up eth0. done. cat

Hi, I''m using Xen 3.0.3 on two servers with Debian Etch (amd64). These servers have 10 nics (2 onboard and 8 in two 4-port cards) so that every vm can have its own interface. This worked so far with the Xen Version from Etch with a wrapper script wich started 10 bridges at boot time. But now I''ve updated Xen on one of these server to Xen 3.2.0 from backports.org and now the

Hi, Has anybody ever stumbled upon the need to replicate a live and in production server to a virtual machine? I''m trying to virtualize a bunch of servers but I can''t figure out how can I mirror the file system. I do not want to start from scratch with them. The whole idea is to transfer them to the virtual side as they currently are. Any advice is welcome. Thank you.

I installed 64-bit xen 3.1.0 (from xensource.com tarballs) on three new machines today, using a configuration setup that I''ve used successfully many times before. However, I encountered a new problem. These are Dell Poweredge 1950 servers, by the way. >From lspci 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) 08:00.0 Ethernet

Hello again, folks! I''m getting one strange problem with FC5 running on XEN 3.0.3 x64... The MRTG point to my machine with XEN running one absurd volume of output data sent (normal is around 6 MB/s) and when XEN is working we get 80 MB/s until my DRAC is alive... after this, the machine crash, DRAC stop do reply, swith stop do work together... Anyone knows whats happening now? ;)

Hello. I have installed the SuSE Linux 10 XEN kernel but no domU yet. Now I cannot ping to and from dom0. I get lots of ARP broadcasts from dom0 but dom0 seems to ignore ARP answers. When pinging to dom0 it ignores arp requests. This happens regardless xend is running or not. This happens in the xen kernel only, when booting stock kernel all works as expected. What can I do? Robert

Hi, I have a set of 32bit HVM images running fine under Xen 3.2.1 and Xen 3.4.1. Due to performance issues with the fully virtualized setup, I would like to migrate one of those images to a paravirtualized image to compare the network performance. As I do not have a Xen-aware kernel for that VM, I thought the best would be to provide one from outside. Sounds like an easy task, doesn''t

Hello. I''ve just started with Xen and configuring Dom0. My hardware is Core2Duo based Xeon server and I installed Debian etch for amd64 architecture. The Xen related pachages installed are the following. linux-image-2.6.17-2-xen-amd64 linux-modules-2.6.17-2-xen-amd64 xen-hypervisor-3.0.3-1-amd64 xen-tools xen-utils-3.0.3-1 xen-utils-common My problem is that when xend is

Greetings! I finally got the install done for a couple of gust OSs (Win 2003 server & Suse Enterprise 10) Bothe gusts are up and running, but - no networking. My setup: Hardware - AMD Athlon 4200+, ABIT Motherboard, 4 GB of DDR2 RAM, 2 onboard GB NICs Host OS- Suse Linux Enterprise server 10 Xen - 3.0.2_09749-0.4 Config file for Win 2003 server guest: # -*- mode: python; -*-