similar to: Poor network performance on Win2k3 DomU

Hello, some have maybe heard of the GPL dirvers for KVM. See: http://www.techworld.com.au/article/316219/red_hat_open_sources_windows_virtualisation_drivers Is there any profit that Xen can get from this ? Matthieu. _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

Hi there. I have been dealing with a conundrum off and on with a VPS of mine. Windows 2003 Standard 32 bit on a Xen HVM instance. Been trying to get the GPLPV drivers working to help boost performance but always seem to run into one major issue: The PV network device looks like it works but actual connectivity is non-existant. Everything else in the GPLPV driver suite works fine. What I want to

I have a Win2K3 domU (and thankfully an image backup of the LVM volume that holds its system disk) I previously installed GPLPV v0.8.9 drivers, the domU boots OK with or without the /GPLPV switch in boot.ini, however with the /GPLPV switch it tries and fails to use the Xen network driver, and so the machine is network-less, so for the past few months I''ve left it using pure HVM

Hi. I have some new 64bit Windows 2008 R2 domU''s running on SLES11/xen_3.4.2. What is everyone using to get 1gb network performance on win2k8? I''ve used GPLPV on win2k3, but I see you have to sign the drivers yourself for 64bit. Maybe that process isn''t difficult, I only glance at the link from gplpv''s page. What is everyone using? GPLPV is about the only

Hi, this shown up today. I had to do a hard reboot as graceful hanged on sync(). ------------[ cut here ]------------ kernel BUG at fs/btrfs/delayed-inode.c:1466! invalid opcode: 0000 [#1] SMP CPU 10 Modules linked in: btrfs zlib_deflate lzo_compress ipmi_devintf autofs4 be2iscsi iscsi_boot_sysfs ib_iser rdma_cm ib_cm iw_cm ib_sa ib_mad ib_addr iscsi_tcp bnx2i cnic uio ipv6 cxgb3i libcxgbi

Hello. We are using gpxelinux from SYSLINUX 4.02. We recently purchased some HP Proliant BL460c G6 servers with Broadcom BCM 57711 10Gbit NICS. We have a very simple pxelinux.gpxe script compiled into gpxelinux.0: #!gpxe set use-cached 1 dhcp net0 chain http://webserver/gpxe/gpxe.php?IP=${net0/ip} The PHP script dynamically creates a config file that looks something like this: #!gpxe set

I''ve just uploaded 0.9.11-pre7. save/restore should be working for 32 bits on both SMP and UP, and maybe for 64 bits although it''s not tested. If someone could test migration it would be much appreciated. The installer seems to not install the drivers under 64 bit environment... but they can then be installed manually. Not sure why at this point.

I''ve just uploaded 0.9.11-pre7. save/restore should be working for 32 bits on both SMP and UP, and maybe for 64 bits although it''s not tested. If someone could test migration it would be much appreciated. The installer seems to not install the drivers under 64 bit environment... but they can then be installed manually. Not sure why at this point.

Hello, I have Xenserver 5.0. When i install a new VM with Windows Server 2003 X64 Standard (R2) and install all windows-updates, it gives me a BSOD when i install the PV 0.9.12pre3 drivers. Steps to reproduce: - Install Xenserver 5 (light/free or Enterprise/trial) - Install a Windows Server 2003 x64 R2 VM from a ISO or CD - Install all windows updates - Download the GPLPV 0.9.12pre3 .exe file

Hi, DomU is a Win2008 R2 64 When i install the GPLPV drivers the network latency goes from 15ms to random numbers up to 1200ms and eventually dies. If you run a ping from the DomU to another host the network stays alive but the high latency is still there. Further more if i try and uninstall the network driver i am unable to use the old one (realtek) as it cannot detect the device.

Hello! Has anybody experienced network latency problems with combination of Windows 7, GPLPV drivers and RDP connection? Any Windows pop-up message(such as "command not found" error message in "Run command:" dialog, or dividing by zero in windows calc) causes a short freeze of RDP session and looks like that from dom0: PING 192.168.44.65 (192.168.44.65) 56(84) bytes of data.

I have been using the built in Xen Paravirt NIC drivers for paravirt networking and had bad performance until I disabled all offload setting on the bridge and paravirt nic (From Dom0). There are 2 related questions I have, where should I be tweaking the offload settings, the Dom0 Physical NIC, The Bridge or the DomU NIC? Which settings in particular tend to cause trouble? (I just disabled all of

Hello, My first post on Xen-Users, so .. i''ve discovered a strange problem. Setup: -A Windows server 2003R2 (x86) with GPL PV driver 0.9.9 ipferf 1.7.0 (from 2003) -dom0 a opensuse 11.0 xen: # rpm -q -a |grep -i xen kqemu-kmp-xen-1.3.0pre11_2.6.25.5_1.1-7.1 kiwi-desc-xenboot-2.38-67.1 xen-3.2.1_16881_04-4.2 xen-tools-3.2.1_16881_04-4.2 xen-libs-3.2.1_16881_04-4.2

I''m running Xen 3.3.0 with AMD Opteron 2350s. Windows 2003 32bit SP2+patches. When I bring a Windows VM up with the GPLPV drivers, it runs until I try to do anything with the network and then it crashes. Trying to web browse will lock the VM up, RDPing to it will lock the VM up. I''ve tried 0.9.11 and 0.9.12pre13, both with the same results. I''ve removed the

Greetings Richard, To add to the above information, we are following the understated steps: 1. We have 2 BL460c (Gen8) with Fedora 21 installed. Both the machines(BL1 & BL2) have been updated with virt-v2v packages 2. On BL1, we execute the following commands: 1. virt-p2v-make-kickstart fedora 2. livecd-creator p2v.ks 3. After creating the

On Sat, Oct 31, 2015 at 06:11:05PM +0000, Richard W.M. Jones wrote: > > On Sat, Oct 31, 2015 at 10:14:32PM +0530, Tejas Gadaria wrote: > > Hi, > > > > We are trying to do P2V conversion with virt-p2v. > > > > we have conversion server (virt-p2v) and physical server (virt-p2v) server > > configured as per below documentation. > > > >

Hi, We are trying to do P2V conversion with virt-p2v. we have conversion server (virt-p2v) and physical server (virt-p2v) server configured as per below documentation. http://libguestfs.org/virt-p2v.1.html#kernel-command-line-configuration After "Start Conversion" from GUI interface, we are conversion fails with "/run/lvm/lvmetad.socket: connect failed: No such file or

I have a situation very similar to whats in http://www.syslinux.org/archives/2013-January/019251.html The server is setup to provide info over dhcp+tftp and I'm planning on chaning that to dhcp+http so I copied gpxelinux.0 to pxelinux.0 and started failing. The client (in my case it's a hp proliant BL460c G7) manage to get gpxelinux.0 loaded but when it comes to load the config file it

I am trying to generate kmean of 10 clusters for a 165 x 165 matrix. i do not see any errors known to me. But I get this error on running the script Error: empty cluster: try a better set of initial centers the commands are M <-matrix(scan("R_mutual",n = 165 * 165),165,165,byrow = T) cl <- kmeans(M,centers=10,20) len = dim(M)[1] .... .... I ran the same script last night and

Hi, I have a simple question ;-) Has anyone made experiences with GPLPV driver and MS Server 2008? Thanks in advance. Cheers, Alex _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users