similar to: RAM disapeared?

Hello. We have a number of Xen 3.4.2. boxes which have constant iowaits at around 10% with spikes up to 100% when accessing data over NFS. We have been unable to nail down the issue. Any advice? System info: release : 2.6.18-194.3.1.el5xen version : #1 SMP Thu May 13 13:49:53 EDT 2010 machine : x86_64 nr_cpus : 16 nr_nodes

Hello! I have new xen-3.3.0 installed and working on latest Ubuntu Hardy, with Linux 2.6.18-xen from xen.org. When I run "xm new" I got this error: root@hyper02:~# xm li Name ID Mem VCPUs State Time(s) Domain-0 0 512 1 r----- 1869.9 vsrv65 4 1024 1

Hello list, I have two differents installation Xen Hypervisor on two identical physical server, on the same switch : The problem is on my new server (Xen 4.0.1 with pvops kernel 2.6.32.24), I have bad performance on bandwidth I have test with a files copy and "iperf". Result iperf average: Transfert Bandwidth XEN-A -> Windows

You need to add dom0_mem=XXXm to xen or scale back the memory of domain0 with using "xm mem-set <DomId> <Mem>" command. Your domain0 used up almost all physical mem. >total_memory : 1023 >free_memory : 62 Thanks Yunfeng >-----Original Message----- >From: xen-devel-bounces@lists.xensource.com

Hello. I recently tried installing NetBSD-5 on xen-4.0.1-rc5, which resulted in no network (xennet0 can''t get IPs per dhclient and has no connectivity if set by hand). Tried it with netBSD-5.1-RC3-1 i386 PAE & amd64, netBSD-5.0 and even 4, all with the same result. On a older xen version (3.3.1) networking works fine, so I assume it''s a xen bug, and not a netBSD-kernel

Hello, Earlier this week I installed a test server with CentOS 5.6 with Virtualization enabled during the installer. Today I installed another server using the same method (they are identical servers). I just did a yum update and I found something curious. Both servers have a different kernel. Server 1 is at 9.1 version and server 2 at 5.1. How can this be? How to I get the latest version on

I installed a 32 bit Windows 2003 enterprise edtion domU. xm list shows the domU has 7G RAM. But Windows 2003 shows only 3.75G RAM. I do not know what''s wrong. Anyone knows? [root@sjd-hot w2k3e]# xm info host : sjd-hot.rashost.com release : 2.6.18.8-xen version : #1 SMP Fri Nov 27 03:53:01 UTC 2009 machine : x86_64 nr_cpus

Hey all, just compiled xen 3.4.2 and linux 2.6.31.12. I followed the instructions on the Xen wiki to get the install running. my issue here is that in my grub memnu config i set dom0_mem=512M when i login to the dom0 and i do a free -m i get that the system only has 432 under the total section. booting into the stock debian kernel 2.6.26-2-amd64 kernel gives me 8192 free memory for i did

Hi All, Debian squeeze, Xen 4.0, 2.6.32-5 I successfully installed opensolaris, but when trying to convert to pygrub it just hangs. root@vhost2:/var/log/xen# xm create /etc/xen/opensolaris.cfg -c Using config file "/etc/xen/opensolaris.cfg". root@vhost2:/etc/xen# xm list Name ID Mem VCPUs State Time(s) Domain-0

Hello everyone, i just updated from 4.2.1 to 4.2.2. If i try to fire up my win2k8 domU with a pci device attached, the dom0 machine hardcrashes. my system log (idrac) shows the following: CPU 2 has an internal error (IERR). A bus fatal error was detected on a component at bus 0 device 0 function 0. CPU 1 machine check detected. and plenty of other entries. The machine hardresets then. If i

hi, thanks for your response. i cleaned that above one and installed in this following steps: * sudo apt-get install gcc make pkg-config libxml2-dev libgnutils-dev libdevmapper-dev libcurl4-gnutls-dev python-dev libpciaccess-dev libxen-dev libnl-dev * ./configure = --prefix=/usr --localstatedir=/var --sysconfdir=/etc --with-xen=yes --with-libxl=yes * make * make install now i am getting the

hi all i am trying to boot from rhel5.1 x86_64 image. with the following configuration kernel = "/usr/lib/xen/boot/hvmloader" builder=''hvm'' memory = 3048 name = "rhel51" vcpus=1 cpus = "" vif = [ ''type=ioemu, bridge=xenbr0'' ] disk = [ ''phy:/dev/cciss/c0d0p7,ioemu:hda,w'',

Hi folks, I met a problem: when 6 VM reboot at the same time, 3:00 morning, the Dom0 reboot it self: Xen version is 4.0.0, VMs are windows 2003 with redhat pv, they will update and reboot itself every 3:00 AM. # last ... ... admin pts/0 10.247.1.1 Fri Jun 25 03:40 - 04:30 (00:50) reboot system boot 2.6.31.13 Fri Jun 25 11:16 (00:-3) admin pts/0

Hi folks, I met a problem: when 6 VM reboot at the same time, 3:00 morning, the Dom0 reboot it self: Xen version is 4.0.0, VMs are windows 2003 with redhat pv, they will update and reboot itself every 3:00 AM. # last ... ... admin pts/0 10.247.1.1 Fri Jun 25 03:40 - 04:30 (00:50) reboot system boot 2.6.31.13 Fri Jun 25 11:16 (00:-3) admin pts/0

Hi Guys, Now I am using Xen-4.0.0. I need to attach CDROM from ISO files to vitual machines when they are running. The VMs contain RHEL4.6, Windows Server 2003 32bit and Windows Server 2006 64bit. The disk configuration of the VMs is: disk = [ ''tap:vhd:/guest/SS_test/vhd/hmi-100130.vhd,hda,w''] (1) When I attach a CDROM to RHEL4.6 VM with the command: virsh

Hi Guys, Now I am using Xen-4.0.0. I need to attach CDROM from ISO files to vitual machines when they are running. The VMs contain RHEL4.6, Windows Server 2003 32bit and Windows Server 2006 64bit. The disk configuration of the VMs is: disk = [ ''tap:vhd:/guest/SS_test/vhd/hmi-100130.vhd,hda,w''] (1) When I attach a CDROM to RHEL4.6 VM with the command: virsh

This patch modifies the physinfo hcall to export NUMA CPU and Memory topology information. The new physinfo hcall is integrated into libxc and xend (xm info specifically). Included in this patch is a minor tweak to xm-test''s xm info testcase. The new fields in xm info are: nr_nodes : 4 mem_chunks : node0:0x0000000000000000-0x0000000190000000

Hi , I have two virtual machines VM1 and VM2. Then I have added eth0 of my VM to 'default' network. Use case :- I want to monitor all traffic on virbr0('default' network). Steps followed :- 1. Add VM1 eth0 to virbr0 2. Add VM2 eth1 to virbr0 3. brctl setageing ovsbr0 0 ..(To put bridge in promiscuous) Now I am running tcpdump on eth1 of VM2 and trying to ping