similar to: kernel oops errors+xen+lvm snapshot

I inherited an ancient Dell Latitude C840 and recently installed CentOS 5.2 on it. It worked fine for the most part, but when I left it overnight and came back the next morning, the screen blacked out and wouldn't come back unless I did a hard reset. Even though I turned off all the power management settings and left it set like a desktop, the next morning after that it still blacked out. I

Hi peploe, i am new in the list, i need know, how blocked the Amule/emule in shorewall? My dist. debian version: 3.2.6-shorewall -- .~. / v \ Seja Livre, use GNU/Linux! /( )\ ^^-^^ ------------------------------------------------------------------------- This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2005.

Hello , The folllowing is the error problem: Validating interfaces file... ERROR: The ''norfc1918'' option may not be specified on an interface with an RFC 1918 address. Interface:eth2 The shorewall interface file: net eth2 detect tcpflags,routefilter,norfc1918,nosmurfs,logmartians P.S. I tried to remove norfc1918 from interface

Hi! How I can use L7-Filter (http://l7-filter.sourceforge.net/) with Shorewall? Thank you very much! Bye. ------------------------------------------------------------------------- This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2005. http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/

Are shorewall-shell and shorewall-common required at compile time even if one only wishes to use shorewall-perl (4.0.9)? ____________________________________________________________________________________ Be a better friend, newshound, and know-it-all with Yahoo! Mobile. Try it now. http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ

In my peculiar setup I need my shorewall router to do one-to-one NAT with RFC1918 addresses. The "external" addresses are 10.215.0.0 and the internal addresses are 192.168.0.0. I can ping, vnc, http, smb from 10.215.144.48 to 10.215.145.237 which is 192.168.44.237 internally. >From 192.168.44.237 I can do http, rdp, ping to 10.215.0.0 hosts. So all seems fine except for the fact

Hi list! I am configuring Shorewall on a Xen domU virtual machine. I configured only the zones, interfaces, rules, policy and shorewall.conf files. When I run "shorewall check" there aren''t no problems, but when I try to start shorewall I get this error a lot of time: iptables: Invalid argument ip6tables v1.3.6: can''t initialize ip6tables table `filter'': Bad

Hi, I have a linux box with vpn client. shorewall version 3.4.0 I can connect to a remote vpn network with the nortel vpn client. Can I allow local machines on my network to access remote vpn using Linux box as a gateway? Thanks and Regards Anuj ------------------------------------------------------------------------- This SF.net email is sponsored by: Microsoft Defy all challenges.

Hi, I''m in a process of setting up a firewall system, which is going to be also an ipsec/l2tp and pptp vpn server for some mobile clients. The problem is, that the system has two ISPs a cable one (no problems here) and a DSL provider. Because of the DSL provider the system is going to have one pppN interface for DSL (net zone) and many pppX interfaces for l2tp/pptp (loc zone)

Perhaps it is obvious, but I have googled a lot and couldn''t find an answer. Is that error message something to worry about? FATAL: Error inserting nf_conntrack_ipv4 (/lib/modules/2.6.13-15.16- default/kernel/net/ipv4/netfilter/nf_conntrack_ipv4.ko): Device or resource busy I am using OpenSuse 10.0 if that matters.

Hi, just wondering if there is anyone that can help me configure my quintum box to operate with asterisk. i have tried and made numerous attemtps configuring the tenor to work with asterisk@home but have been unlucky. anyone out there has a cheat sheet to configure this device. thanks.. for some reason i cannot get it to work. your help is appreciated.

Greetings, There is a very old bug report [0] still floating around asking for a configuration check before restarting on upgrade. While this may not have been possible in the past, would it be possible now with Shorewall-perl? Regards, -Roberto [0] http://bugs.debian.org/200573 -- Roberto C. Sánchez http://people.connexer.com/~roberto http://www.connexer.com

The ''detectnets'' interface option has always been a rather silly feature. For incoming packets, it duplicates the function of the ''routefilter'' option. It provides no value on output since it enforces the same thing that the routing table does. In other words, if you set ''routefilter'' and ''log_martians'' you get the same

Does anybody know a "type 102 milliwatt test number" that I can dial in the USA? I need this in order to configure my "rxgain" and "txgain". My analog line provider, AT&T Repair Center was so confuse, when called them. Thanks in advance. -John _________________________________________________________________ Stay up to date on your PC, the Web, and your

Hello, On my systems i use shorewall 3.2.6. Now all systems where replace by new ones with new ip''s. So i tried with DNAT to map the old ip''s to the new one as long as DNS is updated. But i didn''t get it work. I see in tcpdump that a connect from client-ip to new-server-ip is done while connection the old on. But i get no response. Did i configure something in the

Hello everyone, is a pleasure to be here. I have a problem with my server, it runs qmail SMTP and protect it with shorewall. Since yesterday I get syn flood attacks on port 25, which means that no longer meet. How can I stop this with shorewall? my setup is as follows. zones: #ZONE DISPLAY COMMENTS net Net Internet loc Local Local networks dmz DMZ

Hello! I written several implementations in R of R?my's algorithm for generating random ordered strictly binary trees on 2n+1 vertices. One implementation involves manufacturing character strings like: "X <- list(0,list(0,0))" for the case n=2. If I perform the following two steps: cmd <- "X <- list(0,list(0,0))" eval(parse(text=cmd)) then X becomes a true

I am trying to make the following connection: WindowsXP(OpenVPN-Client)->shorewall->Internet->LinksysWRTG->OpenVPN-Server ...of course the reverse path too. The OpenVPN server is running in bridge mode. When the openVPN client is launched it looks like a successful connection is made. The openVPN client gets assigned an address from the openVPN server pool. The OpenVPN

Hello Tom! After i read and analyze some docs about IFB i decide that for implement this feature in Shorewall not need more efforts (of course i may be wrong). If we have 'ifb0' device then we must activate ingress discipline on real device (f.e. eth2) and redirect 'egress' from it to 'ifb0'. tc qdisc add dev eth2 ingress tc filter add dev eth2 parent ffff: protocol ip

Hello Chuck! I have 128kbit/s for 70 computers and if several users start several FTP/HTTP/Torrent downloads (or one downloads with several threads) or also open several htmlpages with big content, for other users remain not very much. As i hear Squid make traffic shaping on IPaddress base and in my scenario every user will work in equal borders (as another) for all his connections.