similar to: [Q]Are Intel''s ICH9 chipsets supported by xen-3.2?

about VIRQ & PIRQ what is VIRQ  ?How VIRQ is different from PIRQ ?How VIRQ & PIRQ are related each other ? DISCLAIMER: ----------------------------------------------------------------------------------------------------------------------- The contents of this e-mail and any attachment(s) are confidential and intended for the named recipient(s) only. It shall not attach any

Hi All, I tried a usual NAT setup with a Linux HVM guest. Looks straight forward approach. Unfortunately I cannot ping even domain0''s eth0 interface. Xen assigns an IP address for me to vif1.0, where 1 is the domid of my HVM guest i.e 10.0.1.128(changes are per vmid and domid). I manually attached ip address 10.0.1.2 to eth0 in HVM domainU and add default gateway to be 10.0.1.128.

Hi All, I tried a usual NAT setup with a Linux HVM guest. Looks straight forward approach. Unfortunately I cannot ping even domain0''s eth0 interface. Xen assigns an IP address for me to vif1.0, where 1 is the domid of my HVM guest i.e 10.0.1.128(changes are per vmid and domid). I manually attached ip address 10.0.1.2 to eth0 in HVM domainU and add default gateway to be 10.0.1.128.

Hi All, The interface manual says - grant tables provide a generic mechanism sharing between domains. Subsequent lines suggest mechanism sharing between only unpriviliged domains. Can grant tables be used for this capability based shared memory communication between dom0 and domUs? Thanks ~psr -- pradeep singh rautela "proud to be a TUXedo, BSDemons you are a little late" - me

hello, I would like to map (Read/Write) pages owned by a HVM guest from my Dom0 Linux kernel module. I have access to the "machine frame numbers" of these pages. 1. What is the right interface to do this? kmap needs ''struct page'' ptrs which I doubt exist for pages owned by a HVM guest. Is there a hypercall to do this then? 2. Do I need to modify the HVM behavior in

Hi, I have a question about memory page tables in Xen. As far as I understood, every modification to page table will go through Xen(hypervisor). Is it so that all page tables are actually allocated in Xen(hypervisor) instead of guest OS(domain)? Also, is it the case that Xen(hypervisor) needs to maintain a page table for each process running in every domain? Thanks Haifeng

Hello, I am trying to boot a FC6 domU on Xen 3.2 (compiled on a FC6 system). After compiling Xen 3.2 successfully on FC6 and making the ramdisk, I modified the conf.grub as shown below. With this, I was able to boot xen. ------------------------------ --------------------------------------------------------------------------------- # grub.conf generated by anaconda # # Note that you do not have

HI Rusty, I wanted to play with lguest. As it was recently merge upstream by Linus, i took a look and the location looks like driver/lguest*. Unfortunately my local git repo cannot get the 2.6.23-rc2 changes from upstream somehow :-/.[duh... says "Cannot get the repository state from http://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git"]. i do not know what i am doing

HI Rusty, I wanted to play with lguest. As it was recently merge upstream by Linus, i took a look and the location looks like driver/lguest*. Unfortunately my local git repo cannot get the 2.6.23-rc2 changes from upstream somehow :-/.[duh... says "Cannot get the repository state from http://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git"]. i do not know what i am doing

Hi, full ICH9 support for Centos 5 can be found http://fs12.vsb.cz/hrb33/pub/ Take it as a workaround until CentOS 5.1 is released. I hope ICH9 to be included in this version. Support is done by backporting from new kernel versions. Delta file is created with mkdeltaiso from CentOS-5.0-i386-bin-DVD.iso, so full image can be created with applydeltaiso. Regards, David Hrb??

Hi, Well, ICH9 support for CentOS as announced on Oct 16th by me http://lists.centos.org/pipermail/centos/2007-October/088104.html has been extended. Today I have published x86_64 install DVD. You can find it here: http://fs12.vsb.cz/hrb33/pub/ich9/ Regards, David Hrb??

David wrote: >I'll test DVD tomorrow. Today new kernel RPMS are > being built. What ptions are you talking about? > David all-generic-ide irqpoll Without irqpoll it just hangs and without all-generic-ide it get a kernel panic. So I still need both to recognize the disk and continue booting. __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo!

btw - I installed your x86_64 rpms that has the ich9 patch directly on that box but it still will not boot without all the options. --- Michael Rock <mikerocks65 at yahoo.com> wrote: > > David wrote: > > Now there are right md5sums and even > > x86_64 iso.delta. > > David > > I tried using applydeltaiso and it creates a 2gb ISO > but I notice it fails on

Hi all, I've the same problem, I've download the CentOS-5.0-x86_64-bin-DVD.iso from one centos mirror, i've applied deltaiso and the created image is 2 GB, the md5sum check of iso.delta (CentOS-5.0-x86_64-bin-DVD-ich9.iso.delta) is ok, what's wrong ? deltaiso program exit on the same as Michael , maybe I've downloaded the worng DVD 64 bit iso version? do you know any good

Michael Rock napsal(a): > all-generic-ide irqpoll > > Without irqpoll it just hangs and without > all-generic-ide it get a kernel panic. So I still > need both to recognize the disk and continue booting. > Michael, > I have tested 8.1.14 ICH9 x86_64 version and it's kring fine. For sure > im right now uploading full DVD isos. I did not want to :o( due due to >

Hi, As it has been brought to my attention (by several parties), my current MB does not support VT-d. Since I don''t feel like purchasing a brand new system, I have searched for replacement MB-s that would fit into my existing uATX case, support my C2D CPU, and support at least 4x2GB ram. I have narrowed it down to the following four models: SUPERMICRO MBD-C2SBM-Q-O (Q35 chipset)

Hi, testing for bounce mails. suddenly xen-devel started bouncing my mails back saying somebody forged by email to them ... :-( uh... if anybody gets this , please hit a reply privately. Thanks a ton ~psr -- --- pradeep singh rautela "Genius is 1% inspiration, and 99% perspiration" - not me :) _______________________________________________ Xen-devel mailing list

Michael Rock napsal(a): > Hi Dave, > > I am using applydeltaiso with your delta and > CentOS-5.0-x86_64-bin-DVD.iso 4,186,786 bytes from one > of the Centos mirrors. But the block size is wrong and > does not match the image length. > > So I checked the md5 on your delta and it does not > match your md5.txt file. I downloaded it again to be > sure. > > Your

> David wrote: > Now there are right md5sums and even > x86_64 iso.delta. > David I tried using applydeltaiso and it creates a 2gb ISO but I notice it fails on applying. kdnssd-avahi-devel.i386: copying unchanged payload kernel-xen.x86_64 (???): applying delta new payload open failed __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has

> WELCOME TO MY WORLD :D > (Hey, are the new foobar packages done, how about the xwyz packages) > Thanks, > JOhnny Hughes When you snip the rest of my post man that last request sounds really bad on its own. Sorry guys. I saw the "uploading the new DVD's" a few days ago and thought I would ask. I really do not want to put anyone out and please do not go through any