similar to: Xen creating two bridges

I installed 64-bit xen 3.1.0 (from xensource.com tarballs) on three new machines today, using a configuration setup that I''ve used successfully many times before. However, I encountered a new problem. These are Dell Poweredge 1950 servers, by the way. >From lspci 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) 08:00.0 Ethernet

Hi! I have a problem with my new Xen setup. I have installed Debian etch with netinstall and I''m using 2.6.18-6-xen-amd64 kernel in my dom0 and 3.0.3-0-4 version xen hypervisor. I''m using four network cards on my system and using three of them as xen bridges and dom0 is using the fourth one only for it''s own. So basicly both of my virtual servers use a network card

Hi, I''ve set up identical (what I think) machines using SLES 10 x86_64, but a new one of those is saying frequently in /var/log/messages: kernel: bond0: received packet with own address as source address A short summary of ifconfig looks like this: bond0 Link encap:Ethernet HWaddr 00:14:4F:2A:12:9C inet addr:132.199.176.78 Bcast:132.199.255.255 Mask:255.255.0.0 eth0

I am posting the message below again because it did not go through last night. Help! Steve Timm -- ------------------------------------------------------------------ Steven C. Timm, Ph.D (630) 840-8525 timm@fnal.gov http://home.fnal.gov/~timm/ Fermilab Computing Division, Scientific Computing Facilities, Grid Facilities Department, FermiGrid Services Group, Assistant Group Leader.

Hi All, I am facing an issue regarding communicating a value from outside to a Guest OS (linux, solaris and windows) launched on Xen Server. I did went through this thread, but It was not completely clear. http://lists.xensource.com/archives/html/xen-users/2006-07/msg00473.html My question is - Is there a way in Xen, through which I can communicate a value from outside to a Guest OS (linux,

Hi, I tried this post on the Xen list first with no answer. I have 4 machines and 3 of which (all different) have no network access when booted into Xen. I tried using Fedora Core 8 and it produced the same results. Is it normal for the virbr0 interface to take an arbitrary IP? How does it decide what to use? An ifconfig when booted into Xen shows the following: eth0 Link encap:Ethernet

Hey all I''m new to Linux and Virtualizing. I''m trying to dedicate my nic''s to each virtual server. For instance, virt server A would use nic1 and virt server B would use nic2 and so on. I''ve been reading some stuff for this list and to tell you the truth I''m a bit overwhelmed. We are going to run SLES10.1 and Xen. I would appreciate any assistance.

Hi, I have Xen 3.0.3 installed on CentOS 5.5 with 2 paravirtualized domU''s configured to use the default bridge networking and am having networking issues. If I boot the computer fresh I am able to ping dom0 and can SSH into it and start the domU''s. The following ping snippet demonstrates the problem. The first group of "Destination Host Unreachable" is while the

Greetings! I finally got the install done for a couple of gust OSs (Win 2003 server & Suse Enterprise 10) Bothe gusts are up and running, but - no networking. My setup: Hardware - AMD Athlon 4200+, ABIT Motherboard, 4 GB of DDR2 RAM, 2 onboard GB NICs Host OS- Suse Linux Enterprise server 10 Xen - 3.0.2_09749-0.4 Config file for Win 2003 server guest: # -*- mode: python; -*-

Hello, I have been playing with the XCP for a while now, and must say I''m very exited about the technology. I had no prior experience with Xen so it has taken me a while to understand the concepts, but now I feel most important issues are solved and I''ve purchased some hardware to build my (tiny) cloud on. The box is a Supermicro 1026TT-IBXF, so I have 2 x Ethernet and 1 x

Hey folks, I created a DomU, installed Linux, and then realized I''d only given it 1 NIC so brought it down to edit the cfg file to give it another NIC. Originally I just had : vif = [''''] And so I guess the defaults worked for the 1 NIC. So I changed it to : vif =

Dear, I''ve attempted to upgrade a Xen box from 3.1.2 to 3.2.1. Unfortunately it has been a partial success only. At this point I''m really stuck with a network problem that affects my HVM machines (Linux PV run fine). The really odd thing is that everything seems to work properly, except that the "vif" network interfaces in dom0 seem to have only dropped TX packets for

Hello. I''ve just started with Xen and configuring Dom0. My hardware is Core2Duo based Xeon server and I installed Debian etch for amd64 architecture. The Xen related pachages installed are the following. linux-image-2.6.17-2-xen-amd64 linux-modules-2.6.17-2-xen-amd64 xen-hypervisor-3.0.3-1-amd64 xen-tools xen-utils-3.0.3-1 xen-utils-common My problem is that when xend is

Well where do I start...I have a domU (ubuntu) booting and appears well but I don''t have an eth0 listed at all, dom) looks good. DomU: eth0 Link encap:Ethernet HWaddr 00:06:5B:15:C5:0B inet addr:10.99.99.5 Bcast:10.99.99.7 Mask:255.255.255.248 inet6 addr: fe80::206:5bff:fe15:c50b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

Hello, There is a xen setup in which "brctl show" gives the following output. bridge name bridge id STP enabled interfaces eth1 8000.003048c9d4df no peth1 vif1.0 vif2.0

Hi all, did somebody successfuly export ISDN Cards to DomU? I want to have 2 ISDN Cards in DomU (for Asterisk with mISDN) lspci -vt -[0000:00]-+-00.0 nVidia Corporation MCP55 Memory Controller +-01.0 nVidia Corporation MCP55 LPC Bridge ... +-05.1 nVidia Corporation MCP55 SATA Controller +-06.0-[0000:01]--+-00.0 Cologne Chip Designs GmbH ISDN

Hello everybody, Here again with a Xenbr0 bridge problem I''m a Gentoo user, xen-sources-2.6.34 and I always used the bridge from eth0 to xenbr0. Here''s what I get at boot time: * Bringing up interface eth0 * null [...] * Starting Xen control daemon ... And the bridge doesn''t come up. The normal behaviour should be that the Xenbr0 bridge comes up automatically, but

xenconsole fix. reference of tty->count in xencons_close() is racy. It must be protected by tty_sem semaphore like con_close() in drivers/char/vt.c -- yamahata _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel

I'm recording TCP network throughput performance between Dom0 IP stack and all my guest domains (currently 6 running simultaneously). All guests are running simultaneously, but I only ever transmit between Dom0 and one of the DomUs while the other five are idle. When running a netperf TCP_STREAM test (netperf on Dom0, netserver on DomU) I record the following performance numbers, CPU % as

Hi, I''ve installed xen 3.0.3 from packages (xen-linux-system) on a debian etch, and i''ve configured it with network-bridge script in the default way (netdev=eth0, bridge=xenbr0, etc...) which is ok for me. the problem I have: I cannot ping any outer machine from dom0 (nor any outer machine can ping me). It gives me a "Destination Host Unreachable" message that