similar to: Ethernet device problem when using xen.

Hi , I am trying to export home directorie from a FC3 system, running kernel 2.6.10-xen0 from xen-2.0-testing.bk. When i try to mount the /home dit from a other host i get the following error. client: mount: xen:/home/xen/tmp failed, reason given by server: Permission denied server: xen rpc.mountd: authenticated mount request from client230.office.netland.nl:666 for /home/xen/tmp

Hi, I compiled tinc 1.1pre14 for android 6, then i created the config for tinc. When i try to start tinc, it can not connect to /dev/tun I have looked for information on android/tinc and /dev/tun. The information i found is about system permissions, how can i start tinc on android whitout rooting my android tablet ? And set extra routing to the tinc interface. Greeting from Amsterdam,

I am trying to compile tinc on a android tablet. When i do ./configure it does not run because the shell in not /bin/sh but /data/data/com.termux/files/usr/bin/sh. $ which sh /data/data/com.termux/files/usr/bin/sh What do i have to change to make this part of the compile work ? Greetings from Amsterdam, Perry

Hi, I configured 2 vpn's between 2 servers. When starting the tinc on each server. De 2 vpns's look like 1 vpn. Can tinc be configure for multiple vpn's between 2 hosts or more. Lets say there are 3 servers A, B and C. I want a tinc vpn between host A en host B. And a second vpn between host B en C without is becoming one vpn. And for example a third vpn between host A en host

Hi, I want to use tinc for voip phones. How can i measure the overhead ? Compared to a direct connection ? How can i reduce overhead when tunneling voip over tinc ? Greeting from Amsterdam, Perry Couprie

Hi, I want a way to remove/deny a node from the vpn without restarting all nodes. What i did is to remove the hostfile and the ConnectTo but the node i removed is still connected. I did do a kill -HUP. How do i purge the node that i removed, without effecting the other nodes ? Greeting from Amsterdam. Perry

Sure, and thanks for trying to help! These are the two correct answers when SNI is included. The certificates are fully chained. Both certificates carry the same subject mail.cs.sbg.ac.at but differ in Subject Alternative Name (SAN). X509v3 Subject Alternative Name:? ? DNS:mail.cs.sbg.ac.at, DNS:smtp.cs.sbg.ac.at, DNS:imap.cs.sbg.ac.at, DNS:pop.cs.sbg.ac.at X509v3 Subject Alternative Name:? ?

Hi, How long can the the tinc netname be ? -n, --net=NETNAME Connect to net NETNAME. Perry

I have some tinc nodes behind a nat router. Which ipaddress should i use in de host file for the tinc nodes behind a nat router. The internet ipaddress or the private ipaddress ? Perry

JdL> I've always been afraid to ask, but here goes... JdL> What's the advantage of GUEST_SESSSETUP being a compile time parameter, JdL> instead of having it as an smb.conf parameter? I'd like to second this question! Also, just in case that it will not become an smb.conf parameter: can't it be added as a comment to the Makefile (probably near the comments to

Florian, Sorry you haven't heard anything but we've recently decided not to offer this product out side of Holland. If your still interested we have another product called ISDN-Flex that provides SIP/H.323 PSTN access inbound/outbound but you need to be connected on on one of our IP or MetroLan products so we can guarantee the QoS. Rgds, Adam -----Original Message----- From: Florian

Hi, I have a routing problem. When i start tinc it creates the following route in the main routing table. 192.168.2.0/24 dev nb003004 proto kernel scope link src 192.168.2.8 The problem is that i want to use extra routing tables for each tinc vpn. When i set the netmask for the tinc device to 255.255.255.255. The route is not created, how can i add it to a another route table. Setting a

Hi, Can any one explain what the following can be used for ? I want to know , so that i can use it in the future :-) > Add support for VDE through libvdeplug. > > When compiled with vde/device.c, tinc will connect to a vde_switch instance > instead of using a tun/tap device. Perry

Hi everybody. I added two Address values to a host file, one for a ipv6 address en one for a ipv4 address. ci1143800182:Address = 2001:xxx:xxxx:xxx:99b5:d0aa:27b3:d158 ci1143800182:Address = xxx.xxx.xxx.xxx The documentation says : *Address = <**IP address**|**hostname**> [<port>] [recommended]* *This variable is only required if you want to connect to this host. It must

Package: xen-utils-common Version: 3.0.3-0-2 Severity: normal On my systen, the script vif-common fails to retrieve the primary IP address of my ethernet device, preventing a domU from starting. I tracked this issue down to the file /etc/xen/script/vif-common. The function ip_of uses the following shell code to extract the address: ip addr show "$1" | awk "/^.*inet.*$1\$/{print

Hi, I am trying to install tinc on a mac. When starting tinc a /dev/tun0 is created, on linux a device is created with a custom name, something like 'ci00001'. How can i achieve the same result on a mac ? Perry -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://www.tinc-vpn.org/pipermail/tinc/attachments/20130921/3acfb278/attachment.html>

Anyone have recommendations for a highly reliable datacenter located in Holland? Thanks -- Craig White ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ craig.white at ttiltd.com 1.800.869.6908 ~~~~~~~~~~~~~~~~~~~~~~~~~~~ www.ttiassessments.com Need help communicating between generations at work to achieve your desired success? Let us help!

Hi, I just tried to generate keys for tinc. /usr/sbin/tinc generate-keys When generating the key, the rsa key are generated. But ik get de following error, what does it means. Generating ECDSA keypair: Generating EC key failed: error:100AE081:elliptic curve routines:EC_GROUP_new_by_curve_name:unknown groupError during key generation! Perry

Ok. I'll send u that info. On Sat, Nov 23, 2019, 16:50 Phil Perry <pperry at elrepo.org> wrote: > On 23/11/2019 06:48, Ebed wrote: > > Hi, > > > > Yesterday i tried to install centOS 8 on my little router and server, but > > there's no ethernet listed there. I'm using Compaq pressario V3737TU > which > > come with Marvell PCI-e ethernet

Hi, I am using newest xen-unstable package. Everything seems fine and boot is successful. However, it seems that the new xen0 kernel cannot find the ethernet card. I have two cards installed on my blade. When it tries to bring up eth1, it gives: Device eth1 does not seem to be present, delaying initialization. Or if I try to bring up eth0, it gives: Error for wireless request "Set