similar to: Dell / Broadcom NetXtreme II BCM5708

I am having the same problem. But, I cannot access to the following link for solution http://wiki.ncsa.uiuc.edu/wiki/Dell_PE1950_NIC_Firmware_Workaround Can someone send me the content of this link? Thanks. Pete, This may be relevant: http://wiki.ncsa.uiuc.edu/wiki/Dell_PE1950_NIC_Firmware_Workaround - Mike At 8/18/2006 09:40 AM Friday, Peter McEvoy wrote: Hi, I''ve run

Hi, I''ve run into the same issue as: http://lists.xensource.com/archives/html/xen-users/2006-07/msg00599.html In that, running the network bridge script kills networking completely, trying to ping the gateway gives me destination host unreachable. The card is: 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 11) Using the bnx2 module:

Hi, I have a Dell PowerEdge 1950 with two NICs Broadcom NetXtreme II BCM5708 1000Base-T. I installed CentOS 5.1 and Xen 3.0.3 (RPM). One of my virtual machines has Windows 2003 Server. In this virtual machine my NICs appears like "Realtek RTL8139 Family PCI Fast Ethernet NIC". The problem is that when I ping to other machines sometimes the reply time value is very high: C:>

I have a new x3655 IBM and whenever the /etc/xen/scripts/network-bridge script starts, the ethernet would no longer work. This post isn''t about the cause, but the fix. I did a lot of tcpdumps and Googling, but I''ll spare you that. All they do is prove that yes, there is an issue. :) I tried Debian 4.0 i386/amd64 and Ubuntu 7.04 Server i386/amd64 and they all exhibit the

This sounds kind of like what happened with me for earlier attempts at using syslinux. Skip using HPA's tools entirely and dd if=vmlinuz of=/dev/fd0 bs=1440k count=1 and make sure that the kernel runs from a floppy disk. There'll be no file system or anything, but you'll make sure that your kernel isn't faulty. If it doesn't execute, then you can avoid the syslinux/pxelinux

Hello all. We recently purchased HP Proliant DL380 G7 server and also a HP Lefthand P4500 G2 24TB iSCSI box. The server itself has Quad Ethernet based on the BCM5709 Chipset from Broadcom (NetXtreme II). My main question is about iSCSI offload mechanism, as iSCSI itself is pretty new to me but I have gotten a good hold on it tho. I have managed to setup and configured our Lefthand box into

Hi all! We use pxelinux for booting a diskless Linux from whitch we install all our systems. But we discovered some Problems: - With v1.75 the Kernel is fetched from the TFTP-Server with no problem, but it gets not started on Broadcom NetXtreme with newer PXE-Bioses - With v2.04, pxelinux even seems not to be able to fetch the kernel from the TFTP-Server. This affects also Intel's

Does anyone have some tips for setting up Broadcom's 802.3AD support or just getting their driver compiled / installed? First off, I noticed redhat claims the broadcom bcm5708 driver has been added to the rhel4 kernel. But I don't see /proc/net/nicinfo which broadcom claims the driver creates when it's successfully initialized. So, I'm trying to build the driver based on the

I''ve idendified the problem... description: problem in XEN bridged-network. Dom0 doesn''t respond at external network activity (DomUs may work correctly) problem: something related to Broadcom NetXtreme II menagement solution: follow all this instructions: http://article.gmane.org/gmane.linux.hardware.dell.poweredge/23276 bye, s.

Hi all I'm trying to setup second ethernet on Dell 2950 server but there isn't any eth1 device (in the bios are ON) # dmesg |grep eth eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 169, node addr 001c23d878bb eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f4000000, IRQ 169, node addr 001c23d878bd

Hello, I''ve this strange problem. When Xen kernel start and it try to start eth devices, network doesn''t work. It seems to be a problem with NICs firmware. Anyone had this problem? Do you know where I can download firmware upgrade? (on DELL''s site I''ve just searched...) Thanks, Carlo No virus found in this outgoing message. Checked by AVG Free Edition.

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA512 Hi, This is my first version of the block-iscsi script. Easy to setup, easy to work with. > #general > name = "skinkie_gentoo_old"; > memory = 256; > > # booting > kernel = "/home/skinkie/xen/boot/gentoo"; > > # virtual harddisk > disk = [

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA512 Hi, This is my first version of the block-iscsi script. Easy to setup, easy to work with. > #general > name = "skinkie_gentoo_old"; > memory = 256; > > # booting > kernel = "/home/skinkie/xen/boot/gentoo"; > > # virtual harddisk > disk = [

Team I have a Dell PowerEdge R720xd, with the Broadcom NetXtreme bcm5720. I found the following thread: http://forums.freebsd.org/showthread.php?t=31769 I find I am unable to use the NIC's (there are 4 on the server). When we put a cable into it we get a "watchdog timeout -- resetting" error, and the machine will pause for 5 or so seconds. IP may or may not come up randomly.

Hi, For the past day, I have been researching about making dovecot to support mailfront (http://untroubled.org/mailfront/) imapfront-auth natively and able to use mailfront imapfront-auth with dovecot imap v1.2.16 without starting any dovecot related services and no /etc/dovecot.conf file is required. More information about this can be read at:

Hi Marek, Is it possible for you to provide a backtrace of the crash? And can you file a bug report at bugs.gluster.com? Also if possible can you upgrade to 2.8 release and confirm whether you face the same problem? regards, ----- Original Message ----- From: "Marek" <mb at kis.p.lodz.pl> To: gluster-users at gluster.org Sent: Thursday, November 19, 2009 7:20:44 PM GMT +04:00 Abu

While exploring some btrfs maintenance with respect to defragmenting I ran the following commands: # filefrag /path/to/34G.file /path/to/5.7G.file /path/to/34G.file: 2406 extents found /path/to/5.7G.file: 572 extents found Thinking those mostly static files could be less fragmented I ran: # btrfs filesystem defragment -c /path/to/34G.file # btrfs filesystem defragment -c /path/to/5.7G.file and

Hello, Today I was benchmarking DV video on a AMD64: skinkie@zwartepiet ~ $ cat /proc/cpuinfo processor : 0 vendor_id : AuthenticAMD cpu family : 15 model : 47 model name : AMD Athlon(tm) 64 Processor 3500+ stepping : 0 cpu MHz : 2210.197 cache size : 512 KB fpu : yes fpu_exception : yes cpuid level : 1 wp : yes

What are the major differences between Versions 1.x and 2.0? I am beginning to set up a new mail server for a small group of users (~20 accounts). Options are the "0.99" version pre- packaged with RHEL-4, or building v1.2.16 or v2.0.7. Just wondering what the list recommends for a new installation. Thanks, - Don

Hello, When upgrading Dovecot, I get this: Dovecot version mismatch: Master is v2.0.6, imap-login is v2.0.7 (if you don't care, set version_ignore=yes) This should not occur as version_ignore=yes is in dovecot.conf, at the top. Cheers, Olivier