similar to: Same IRQ in dom0 and domU by different hardware causes dom0 crash

Hi, I'm having trouble with one machine that kernel panics with Asterisk 1.4. The motherboard is an Asus P5W Deluxe. I reported the kernel panic here: http://lists.digium.com/pipermail/asterisk-users/2009-November/241006.html I'm now trying to understand if the problem can be an IRQ issue or not. I disabled APIC in the BIOS because I thought that maybe it could be buggy (not sure

hi, i just found a page on the net which might me worth some lines. for the urgent reader: http://isdn.jolly.de there is a guy in germany who has successfully programmed a gpl-patch for isdn4linux to make isdn cards with the hfc chipset from cologne chip (http://www.colognechip.com) run in the NT mode (up to 2.4.20). this mode is needed to connect isdn device to a pc and enables the use of

hi i am experiencing some problems with the configuration of an BN8S0 Beronet card. I've downloaded last CVS of mISDN ans mISDNuser, i patch the kernel 2.6.16.18 and the enabled the following: <*> ISDN support x x Old ISDN4Linux ---> x x --- CAPI subsystem x x <M> CAPI2.0 support x x [*] Verbose reason code reporting (kernel size +=7K) x x [*]

Hi list, Attempting to get an ISDN-BRI line connected using an HFC-S PCI card together with Asterisk v1.4.14 and Zaptel 1.4.7 on a Debian etch system, I find that I can't access the card's resources because the channels are always be busy. An attempt to call out results in the following CLI output: == Primary D-Channel on span 1 down == Primary D-Channel on span 2 down

Hi, I have a Fedora 7 xen system with a domU to which I have delegated via pciback two isdn pci cards. One is a HFC-S card, the other a AVM Fritz!Card Pci 2.0. In the domU I load mISDN drivers for the cards. The two cards are recognized and function well UNTIL I either decide to unload one or both of the card driver modules (hfcpci and avmfritz) or I decide to shut down the domU. At this

Hi, In my system, I can see : # cat /proc/interrupts CPU0 CPU1 CPU2 CPU3 .... 16: 22252 22220 22209 22211 IO-APIC-fasteoi uhci_hcd:usb1, b4xxp I'm quite new with this topic, so if someone has experience about this, ... Does the line above means my HFC board is sharing IRQ16 with another device (specifically uhci_hcd:usb1) ? Regards

Hi list, Has anyone been able to get ISDN-BRI support to work reliably on Asterisk 1.4? If so, I'd love to know how you did it (hardware, distro, kernel, modules, versions, config files). I've tried to get it to work on a Debian etch system with an HFC-PCI card and the zaptel package (v1.4.7, also from xorcom.com), but with no luck: all three channels that are created when the

Dear R helpers, I have molten data which is : - > t3 Year variable value 1 2005 ICICI.Bank 274883700000 2 2006 ICICI.Bank 431668500000 3 2007 ICICI.Bank 595153000000 4 2008 ICICI.Bank 630857600000 5 2009 ICICI.Bank 545263300000 6 2005 HDFC.Bank 2658600000 7 2006 HDFC.Bank 7891000000 8 2007 HDFC.Bank 18031100000 9 2008

Hello, I am having problems, getting my asterisk-domU to work properly. It consists of the following components: - Debian Etch under Xen-3.1 with a 2.6.18-kernel - Asterisk 1.2.24 - mISDN-1.1.5 I have 2 HFC-ISDN-cards, which I pass through to the Asterisk-DomU in permissive mode. This is working fine. The strange problem is, that the two HFC-ISDN-cards are not beeing initialized by the

Hi, I'm very new to asterisk and managed to set one up in debian, I installed via apt-get the asterisk and asterisk-bristuff packages. I downloaded the bristuff source as well. I managed to get as far as loading the following modules: zaptel 199144 4 cwain,zaphfc,zttranscode,ztdummy But the problem now is that all channels that I try to configure gives me an error that

Need some help if anyone can provide it on this issue. I have a very basic setup and am trying to have samba utilize openldap. I have made sure the password is correct but for whatever reason, I am unable to connect. Here is a log of what is going on. Any help would be greatly apprecated. TIA Maximum core file size limits now 16777216(soft) -1(hard) get_current_groups: user is in 7 groups: 0,

Hello List, is someone operating a DID /P2P / Anlagenanschluss with more than one HFC-Based ISDN-Card ??? I have now 12 hours of setup-troubles behind me with Colt-Telekom, where we did not get it working with two HFC-based cards. Here the setup: - 2 HFC-ISDN-Cards (the one from Conrad-Electronic) - bri-stuff.0.0.2 (with the asterisk-sources from the download.sh-skript) - two NTBAs from

Hello everyone. I've got this really annoying HFC Cologne card (or however I should call it - a single channel ISDN card based on the HFC chipset). It wrongfully detects lots and lots and lots of incoming DTMFs, to the point the card is not usable. Here's a sample out of CLI: P[ 1] I IND :DTMF_TONE oad:206361 dad:520101 P[ 1] --> mode:TE cause:16 ocause:16 rad: cad: P[ 1] -->

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

Hi all, On an Asterisk/Zaptel 1.4 system, one way to gather diagnostic info is: ~# cat /proc/zaptel/* Span 1: ZTHFC1 "HFC-S PCI A Zaptel Driver card 0 [TE]" (MASTER) AMI/CCS 1 ZTHFC1/0/1 Clear (In use) 2 ZTHFC1/0/2 Clear (In use) 3 ZTHFC1/0/3 HDLCFCS (In use) Span 2: ZTHFC2 "HFC-S PCI A Zaptel Driver card 1 [TE]" AMI/CCS 4 ZTHFC2/0/1 Clear 5 ZTHFC2/0/2

This is my first posting to the list. Thus hopefully the question has not been asked several times before... I'm trying to install asterisk on a PC using Debian Sarge but without any real success... Problem: I may get the Asterisk packet (Debian version) installed using 'apt-get install asterisk', but that does not include the bristuff from Junghanns

Hello list, After upgrading from BRIstuff 1y-b to 1y-e my ISDN card is suddently detected as 2 ports instead of 4. I still load the driver as "modprobe qozap ports=12" as I've always done. But now it only sees 2 ports. Output of "lspci -vvv" ------ cut -------- 02:01.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01) Subsystem:

Hello, I've been using * for quite a while using AVM C4 card and a few Grandstream Budgetone 102 hard phones plus couple of HandyTone 286. Echo is a big problem. I am getting used to it, but some users complain. Anyone has experience w/ regards to echo comparing the AVM C4 with two HFC-cards? Before shelling out time and money, maybe someone else already has done so, and could tell me if

Hi list! I'm currently using a HFC-S card for my ISDN BRI line with bristuff. The instability is driving me crazy however. I'm having continuous problems where inbound calls will not work after some time of operation (the number then appears as not in use to the caller) or also outbound calls do not work. The solution is to unload the modules, stop asterisk, re-load the modules and

Hello I have asterisk running in Red Hat 9 with a cheap HFC card on i4l. I have choppy sound problems sometimes, and echo problems often. I am using a 2 port Grandstream ATA, Grandstream BT and a Grandstream GPX-2000 I read that changing to BriStuff will fix the echo problems, but have also read other users say that the only way they solved the echo/choppy sound problems was using a Fritz ISDN