similar to: guest Windows XP

I discovered that IPv6 is sort of working when I got an email rejection from Comcast for not having an IPv6 PTR record. I discovered I could telnet to port 25 on their MX server over IPv6! I then found I could tracroute6 to them, but I couldn't to my Linode VPS in Fremont. It gets to the data center and stops. Going the other way, my Linode can traceroute6 almost to my AT&T-hosted

I am running Asterisk CVS-HEAD-07/14/04-16:28:29 and noticed that when I send a subscribe I get back a 403. This used to work in an old version which I forgot to record before upgrading to the above version. Any suggestion? I can register fine with the * server. Sip read: SUBSCRIBE sip:2486@192.168.0.2:5060 SIP/2.0 Via: SIP/2.0/UDP 192.168.0.1:5060;branch=z9hG4bK46F2668 From:

Hi ! I have install the xen4+centos5 on my server following the post of the kernel version is 2.6.32.27 which is download from git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git But after I reboot the server ,and run the "ifconfig", whose output likes the following [root@localhost scripts]# ifconfig eth0 Link encap:Ethernet HWaddr 00:15:C5:EB:96:C3

I'm having a wireless connection issue with an HP laptop and a Zotac media server after the 6.4 package updates from CR repository. Nothing changed with wireless config as far as I can tell. Both have been working fine with previous releases of 6.x. Oddly, if a cat 5 cable is connected for a few seconds and then disconnected the wireless works fine and survives a 'service network

Hello all I have weird problem i can't understand and don't know where to look. [root at chamber ~]# ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host

Hi all, I need to (quickly!grrr) update IP addresses for which a given machine will answer. I did this: /sbin/ifconfig eth0:0 xx.xx.xx.10 netmask 255.255.255.0 /sbin/ifconfig eth0:1 xx.xx.xx.11 netmask 255.255.255.0 /sbin/ifconfig eth0:2 xx.xx.xx.30 netmask 255.255.255.0 /sbin/ifconfig eth0:3 xx.xx.xx.31 netmask 255.255.255.0 /sbin/ifconfig eth0:4 xx.xx.xx.13 netmask 255.255.255.0

On 4/28/2020 3:17 PM, Chris Adams wrote: > - gateway sends a router solicitation and gets a router advertisement > with "stateful config" set, which tells gateway to do DHCPv6 (but > default route comes from RA) I'm not seeing any outbound IPv6 traffic from my CentOS 7 box on the WAN interface. I do see RA's emitting from the LAN interface, from radvd. Is there

Hello! I have two problems. One is, that I cannot ping a DomU from Dom0 (or any other host in my local network) and the second one is, that I cannot ping the same site (eg. www.suse.com) from two DomU''s at the same time. I have a fresh installation of openSuse 11.0 with Kernel 2.6.25.20-0.1-xen and my box has two physical ethernet cards. As far as I have investigated, eth0 is the one

[mod: Forwarded by Jeff Uphoff. I tried to mangle the headers that it appears as the original post: with an invalid return address. -- REW] A few months back, a very alpha version of bliss got posted. That shouldn''t have happened, but, it was pretty much ignored so I didn''t worry about it. But now it seems there''s a bit of a fuss about this. I''ll post the

This is fresh install of CentOS v6 and Xen v4.1 on a new Dell server following the tutorial posted at: http://wiki.xensource.com/xenwiki/RHEL6Xen4Tutorial   Every thing went just fine, yet virbr0 won''t work and when I run brctl show I get the following error message:   [root@pe1950 ~]# brctl show bridge name     bridge id               STP enabled     interfaces virbr0         

This is fresh install of CentOS v6 and Xen v4.1 on a new Dell server following the tutorial posted at: http://wiki.xensource.com/xenwiki/RHEL6Xen4Tutorial   Every thing went just fine, yet virbr0 won''t work and when I run brctl show I get the following error message:   [root@pe1950 ~]# brctl show bridge name     bridge id               STP enabled     interfaces virbr0         

Hi folks, I''ve been trying to work out this situation for a few days now without much success and dug all over the archives for similar issues, none of which seem to relate exactly. I installed Debian Etch and the Xen (3.03) kernels / binaries on a Dell server. It works fantastic with all the default configurations with one strange flaw - as soon as the /etc/xen/scripts/network-bridge