similar to: dom0 networking disabled

Hi everybody, First of all, let me say that I searched a lot on the internet. I spent several hours sitting after my notebook, but I can't configure my network bridge in Ubuntu. I'm really desperate, so I hope somebody can point me out what I'm doing Hardware: ----------------------------------------------------------- $ lspci | grep controller 06:05.0 Network controller: Intel

Greetings, I have two vms, one is a router and the other one is a client, for some reason, the client vm is unable get ip via dhcp from the router vm. here are outputs: vm1.xml: <interface type='bridge'> <mac address='52:54:00:54:78:be'/> <source bridge='virbr0'/> <model type='virtio'/> <address

So Working on CEntOS 5 I am trying to sett up Xen with 2 bridges, one that connects dom0 and most of the domU to the physical card and the out to the network. Got that figured out no problem, now i want to have a second bridge that runs a local network for all the doms that doesn''t connect to the network. With code I have found used in multiple places I can easily get 2 bridges, and

Hello, I am facing some problems in bridged networking. I have successfully created a bridge br0 and added a virtual machine to it. Now the address of virtual machine is 10.1.3.31. I am able to connect to this virtual machine by another computer on same network. The virtual machine is hosting a simple python http server on port 8000, while some other service is running on port 80 When I try

Hi! I have a problem with my new Xen setup. I have installed Debian etch with netinstall and I''m using 2.6.18-6-xen-amd64 kernel in my dom0 and 3.0.3-0-4 version xen hypervisor. I''m using four network cards on my system and using three of them as xen bridges and dom0 is using the fourth one only for it''s own. So basicly both of my virtual servers use a network card

Hi, I have a new xen hosting platform. I have given the bridge a static IP which I can ping/ssh to etc, when I create a new vm all works well apart from the networking. If I give DomU a static IP I can''t ping out from the box, Dom0 can''t ping the vm. I''m suspecting it just isn''t seeing the bridge but am unsure where to start looking. This is a very standard

TEQL and Subnet problem I have a network topology shown below, and I am trying to use TEQL. My problem is: When I ping to P3.teql0 from P2 ("[P2]# ping 16.119.144.66"), the traffic can never go from P2.eth1, and all traffic only goes to P1.eth0. What P2.eth1 (16.119.144.33) did is broadcasting an ARP asking for the MAC address of 16.119.144.66, although I have specified the route to

Package: xen-hypervisor-4.1-i386 Version: 4.1.1-1 Severity: important Tags: wheezy I cannot boot a domU with networking after installing the package. root at topsail:~# xm create /etc/xen/udevtest.cfg -c root at topsail:~# Error: Device 0 (vif) could not be connected. Hotplug scripts not working. [2011-08-03 15:56:53 4411] DEBUG (DevController:139) Waiting for devices tap2. [2011-08-03

Hi, I have Xen 3.0.3 installed on CentOS 5.5 with 2 paravirtualized domU''s configured to use the default bridge networking and am having networking issues. If I boot the computer fresh I am able to ping dom0 and can SSH into it and start the domU''s. The following ping snippet demonstrates the problem. The first group of "Destination Host Unreachable" is while the

Hello, my current network setup looks like the following: dom2-eth0 (172.30.1.22) netmask /24 | | xen-br1 (no ip) | dom1-eth0 (172.30.1.21) netmask /24 dom1-eth1 (172.30.0.21) netmask /24 | | xen-br10 (172.30.0.1) netmask /24 | dom0 | | xen-br0 (normal IP) | eth0 (same IP as xen-br0) |

I installed 64-bit xen 3.1.0 (from xensource.com tarballs) on three new machines today, using a configuration setup that I''ve used successfully many times before. However, I encountered a new problem. These are Dell Poweredge 1950 servers, by the way. >From lspci 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) 08:00.0 Ethernet

Hello. I''ve just started with Xen and configuring Dom0. My hardware is Core2Duo based Xeon server and I installed Debian etch for amd64 architecture. The Xen related pachages installed are the following. linux-image-2.6.17-2-xen-amd64 linux-modules-2.6.17-2-xen-amd64 xen-hypervisor-3.0.3-1-amd64 xen-tools xen-utils-3.0.3-1 xen-utils-common My problem is that when xend is

Hello everyone, I have been able to get windows xp to run under a virtual machine, but i cannot get any network access. My desktop is connected to a university network, and we are only given 1 ip address. so i understand i have to use routing instead of bridging, right? i have commented the two lines for bridge and enabled routing in /etc/xen/xend-config.sxp next i inserted a line: vif

Hello, I have problems with installation of my second DomU. I cannot ping it from the outside world and I cannot access outside world from this domain. I see it from Dom0 and my first DomU, same as my second DomU can ping Dom0 and my first DomU. I use xen 3.0.3 on ubuntu 6 LTS. DomU is running on debian. I also network-bridge script in the xend config.

Hello, I''ve read the FAQ and searched the mailing list but have been unable to resolve my issue with networking in DomUs. The following things I CAN do: +SSH from within DomU to Dom0 +SSH from within DomU to all other DomUs on the same machine +SSH to other machines from within Dom0 +SSH from within DomU to other machines +SSH from other machines to Dom0 (and use the xm commands to

Hello. I need your help, DomU xen network diconnects randomly, how do you monitoring this? When I connect to vnc server in the hosts, DomU is running, then I open the DomU, after that guest network responds. DomU Debian 6.03 over Centos 5.7 and Xen 3.03. My network configuration: eth0 Link encap:Ethernet HWaddr 68:B5:99:78:AA:6D inet addr:192.168.5.230 Bcast:192.168.5.255

Hi, I have a fc14 box with two interfaces that I'm having some difficulty setting up a bridge properly. I have a few kvm guests set up and running, but I've switched from using NetworkManager to using standard networking with a bridge. I've modified the ifcfg-eth0 and created ifcfg-br0 as per the standard documentation, but I think I'm having routing problems. This is what the

Hi list. I started with Xen yesterday, but I am facing a bit of a problem. My system had always configure eth0 with 10.0.0.4/8 I am using Xen unstable source (on Debian sid) Now I installed Xen, rebooted the machine, and first the usual network is coming up and then the xend will be started. I''ll end up with this, but I am wondering if this should be the way of things to be

I am posting the message below again because it did not go through last night. Help! Steve Timm -- ------------------------------------------------------------------ Steven C. Timm, Ph.D (630) 840-8525 timm@fnal.gov http://home.fnal.gov/~timm/ Fermilab Computing Division, Scientific Computing Facilities, Grid Facilities Department, FermiGrid Services Group, Assistant Group Leader.

hi, i''ve tried again Debian testing, with xen 3.1 binary. it works fine but i can''t have the networt working: i''ve have an ethernet card with static IP: 172.20.2.160 gateway: 172.20.2.1 uname -r :2.6.18-xen without xen, the network works fine. here''s my output: eth0 Lien encap:Ethernet HWaddr 00:0F:FE:6B:57:32 inet adr:172.20.2.160