similar to: Anyone running Xen on HP DL380 G5? Intel 5150 and 5160 CPU''s?

Hi I'm having problems getting the TE420 working in HP DL380G5 servers. The cards don't seem to be detected 100% by the BIOS. With two cards in the server they are never detected. things I've tried: 1 Update firmware to latest (P56) for the server 2 change irq settings 3 disable all onboard devices on server and remove raid controller 4 different cards in different slots What I

I have CentOS 6.x installed on a "HP ProLiant DL380 G5" server. It has eight 750GB drives in a hardware RAID6 array. Its acting as a host for a number of OpenVZ containers. Seems like every time I reboot this server which is not very often it sits for hours running a disk check or something on boot. The server is located 200+ miles away so its not very convenient to look at. Is

The HP DL380 G5 (like many rack servers) has no AMP Mate-n-Lok connector available to attach to a card that needs more power than the PCI bus can provide, like the TDM400P when FXS modules are used. HP has confirmed that there is no part they sell to give you such a connector, and Digium says their business edition folks got it to work, but only by doing nasty warranty-voiding things to the

Hi All: Has anyone tried using an LSI MegaRAID 320-2E PCIe RAID Controller in an HP DL380G5 (of any HP G5 DL for that matter) running CentOS 5? It looks like it should work but it would be nice to know that someone has already done it before I start going to all the effort and expense of building the box. I have a spare DL380 and a couple of IBM EXP400 disk arrays that I would like to configure

Hi All I will need to install CentOS 5.3 on HP DL380 R05 server with RAID-1 required. I am a newbie to CentOS / HP servers, need your help: - Does CentOS 5.3 work smoothly with HP DL380 server especially recognizing SAS disks and hardware RAID-1 features? From you experience, do you have to use HP Storage Drivers provided for RedHat Enterprise Linux 5? - How is HP

Hi, folks, Since I've gotten a total of one response in days on the HP forum, maybe the collective mind here has an answer.... As I've mentioned in other posts, we have an HP dl580 g5 that started throwing ECC errors. But wait, it's worse: memory is mirrored.... And the thing is fully populated with 32 DIMMs. I took my best guess, pulled the matching set of DIMMs, and took two

Hi, i''am trying to build a Gentoo Dom0-kernel booting a HP DL380 G6. Has anyone twiddled a working kernel configuration for this hardware? i do have the linux-2.6.32-xen-r1 sources checked out by portage and tried some configurations. Olaf _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

Hi. I am trying to boot Xen 2.0.5 on an HP DL380 G3. It won''t. The box has an "HP Smart Array 5i" that when running normal Linux is handled by the CCISS driver. I suspect that this is what is not supported in the stock Xen kernel. Am I correct that I need to build a kernel from source ? According to http://lists.xensource.com/archives/html/xen-devel/2004-11/msg00709.html there

A customer is looking to replace or augment their Sun Thumper with a ZFS appliance like 7320. However, the Thumper was used not only as a protocol storage server (home dirs, files, backups over NFS/CIFS/Rsync), but also as a general-purpose server with unpredictably-big-data programs running directly on it (such as corporate databases, Alfresco for intellectual document storage, etc.) in order to

greetings, for those of you in the know, may i have some assistance in helping to make better decisions in purchasing more used server toys to install CentOS on please? :-) in the Compaq Proliant Rackmount DL380 line, the one that looks like the older 1850R is called a G1 meaning Generation 1 right? and then the DL380 G2 is a redesign that is gray and just has 6 drive bays up front correct?

Dears, I hope this email finds you well and in a very good health, I've been installed Centos5 on HP DL380 G5 server(Dual Processor), but actually we are unable to see the other CPU, during boot I get this error message, Module microcode doesn't exit /proc/modules Please advise. Thanks Anas Al-Naffar Anas Al-Naffar Content Manager Tel.: +966 1

Hi, i have a proliant dl380 g5, with an amd as1000. I try to install centos8 with gui, but when try to start the new installed system, the xserver don't start. There is a throuble with the amd es1000 driver. This grafic card, seems not supported more from amd. I need a minimalistic gui for study for rhcsa certification. The gui is mandatory for the exam. Any help? Paride

greetings i have a few dual P3 Compaq 1850R units and use compaq smartstart 5.5 on them before a CentOS 4 load i have acquired some dual P3 Compaq DL380 G1 i.e. Generation 1 units and am wondering which specific smartstart download i should be using for them from this URL below h18004.www1.hp.com/support/files/server/us/subscription/ssdownloads.asp would someone please share their experience

Hi list, After a lot of testing + troubleshooting, I guess I'm observing what I am now calling a regression with zaptel 1.4.10 (is it?) As such I call for peer feedback, before either asking Digium install support or filing a bug. Thanks in advance! System: HP Proliant DL380 G5 with 2x PCI-X + 1x PCIe riser card OS: Centos 5 Kernel: 2.6.18-53.1.14.el5 (also tested under

Was there any resolution on this I also have a TE410P in an box with an Intel E7501 chipset? -Vickers -------- Original Message -------- Subject: RE: [Asterisk-Users] Re: TE410P card in an HP-Compaq DL380 G4 server Date: Tue, 8 Feb 2005 11:13:24 +1030 From: Peter Childs <peter.childs@nec.com.au> Reply-To: Asterisk Users Mailing List - Non-Commercial Discussion

Hi to all out there using HP DL380 G4 servers, i found a way to get the Digium TE410P with older firmware running on a HP-Compaq DL380 G4 Server! Here's the step-by-step description: 1. download the latest BIOS (in my case it was 4.04 from date: 06/02/2005) for the HP-Compaq DL380 G4 using the "Systems ROMPaq Firmware Upgrade Diskette for HP ProLiant DL480 G4 (P51) Servers" Link:

Good afternoon everyone, I''m trying to compile the xen 2.6.32.x pv_ops kernel on centos 5.5 with i386 quad core xeon system (HP DL380 G3). Having some issues during the kernel compile one of which related to intel agp so I just removed it from .config and didn''t come across it again. This error here has got me stumped though: drivers/built-in.o: In function

I am considering a G5/XServe for a conferencing system. I need to put a TDM card in the machine for timing. Is anyone out there using Asterisk on Mac with zaptel drivers? I am looking at using Linux for the OS. If so what is your experience? Have a great day! Geoff

Hi, Has anyone had success using a TE410P card in an HP-Compaq DL380 G4 server? For me the card is detected fine, but the system just never sees an interrupt from the card. I've tried everything I can think of. The card definitely works. Its Fedora Core, but we also tried a stock 2.6.10 kernel. We tried with and without Hyperthreading, with "noapic", we disabled all the

Hi all, I have been trying to solve nouveau issues on my iMac G5 for ages. As far as I can understand it, there is a problem with nouveau and page size mapping. I tried both 64K and 4K page size kernels and the the result is always distorted video. There is an old To-Do list, which says "fix the page size mapping problem on G5/64 bit for exposing fifo regs" on