similar to: IBM eServer x366 with Xen?

Hi. We look to switch from XenServer, as it latest versions do not run on our eserver xSeries 336 server. Does the XCP 1.1 fully support this hardware? Also, any idea how well the Xen tools, such as XenCenter and Xen HW->VM tools supported in 1.1 release? I seen there is a feature called XAPI that makes the XCP look as fully-featured XenServer. Thanks.

Hello: I have an odd problem with an IBM EServer XSeries 305 (aka x305). Sometimes it seems to just sit there, completely unresponsive to the command line (ssh and console), for several seconds. Other times it works normally. top will sometimes die with a floating point error while waiting for it to start. When top does work, it often shows a system load of 0.5, with high interrupt load. At

I'm trying to install CentOS 4.2 on an old IBM x300 server, but it hangs during the boot from cd. The last entries I can see before it dies are the two "agpgart" lines. I've been playing around with bios settings (video settings and serial settings since the serial driver is the next thing going on in the kernel) and boot params (noapic, acpi=off etc) but I just can't

Hi, I have an IBM xSeries server... and the digium card is sharing IRQ with USB and giving me crackling audio. >>> cat /proc/interrupts >>> >>> It brings up these results: >>> 0: 10566547 IO-APIC-edge timer >>> 1: 9 IO-APIC-edge i8042 >>> 2: 0 XT-PIC cascade >>> 8: 1

On 30/10/2018 14:49, mark wrote: > I wouldn't expect a system 1, if that's the current name AS/400 -> eServer iSeries -> System i -> Power Systems RS/6000 -> eServer pSeries -> System p -> Power Systems So the current 'Power Systems' range combines what was AS/400 with what was RS/6000. They all use Power CPUs now and run Linux, IBM i, or AIX. "IBM

Hi, I have a problem, probably with the SiI 3512 SATA150 controller in a dual-Opteron IBM eServer 326: Every once a while the kernel issues a message like: ad4: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=150190687 The system waits a few seconds and continues to work normally. It typically occurs several times a day most likely depending on the load of the (SATA connected) hard drive.

Hello everyone, I''m totally new to Xen and trying to run it on some platforms (x86, x64) using SLES (that is what I have to use for reasons other than technical). Several machines on which I tried using Xen simply fails to run normally using Xen kernel: either network communication is not functioning at all despite proper configuration (that works on non-Xen kernel), or the kernel

Hi All, I recently got some IBM Xseries 335 servers 2nd hand, and noticed they don't have any graphics card. Some google searched indicate they only have an uplink port, which you could connect to another (other model) IBM server and use that as the head node. But, I don't have one available. It has 2x GB NIC's, and what looks like a management port, but I can't figure out how to

ok now i bought an IBM xSeries 206 but my problem is the hard drive can't be detected. I tried surfing for drivers for SATA and i found one for RHEL 3 can this driver works for CentOS 4.2? -- Regards, Mark Quitoriano, CCNA Fan the flame... http://www.spreadfirefox.com/?q=user/register&r=19441 -------------- next part -------------- An HTML attachment was scrubbed... URL:

Does anyone recommend any particular SAS controller, or should I use an Ultra-320 SCSI controller instead? My machine is an IBM xSeries 306m. It has a SAS controller provided on a daughter card, but it''s not supported in the 2.6.16 kernel, so I''m looking for a separate disk controller card that will work with my existing SAS disks. -- James Holmes Programmer/SysAdmin RTDS

Hi , I have setup xen on a number of different machines already; however, I couldn''t get xSeries 330 working with Xen. When it boots up, it says "Waiting for device /dev/sda1 .... device not found" and then return a shell prompt. I have looked up this error on the mailing list. I found that the error is potentially caused SCSI driver and it can be resolved this problem by

Does anyone have experience installing Xen on IBM eSeries (I have an x336), specifically with getting all the drivers to work? _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

Dear all, I''ve installed Xen 3.0.1 on my laptop and dom0 is boot normaly execpt it''s could not using X, i haven''t trying to boot guest OS. my laptop configuration is Toshiba Portege R150 with Debian Sarge on it. And then I installed same version of Xen into our server with Debian Sarge and Kernel 2.4. Booting dom0 is not success , xen always trying look dor NFS root and

Does anyone on list have experience with Digium hardware in the following servers: Dell poweredge SC440 IBM xSeries x226 Have just had major hassles getting TE205P ISDN cards going in these boxes. No joy so far. Anyone managed to do it yet? Thanks. Mark

I hope the CentOS people don't mind me cross-posting for their input. I've just done a clean, text-mode minimal WBEL4 install on an IBM Netfinity 4500, essentially the same hardware as an xSeries 340. The install went fine but now the box will boot, run through the initrd init sequence, perform its switchroot then hang here... SELinux: Initializing. SELinux: Starting in permissive mode

I need to install CentOS 5.2 on a IBM Server xSeries 226, which comes with a IBM SERVERAID 6i RAID card. I think it is not a true hardware RAID card. I has, nevertheless, an interesting feature: 128MB of cache with battery backup. I launched the CentOS boot DVD and CentOS correctly identified the card and the RAID 5 array as configured by the controller's BIOS. My question now is:

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 ______________________________________________________________________________ Caldera Systems, Inc. Security Advisory Subject: serious bug in setuid() Advisory number: CSSA-2000-014.0 Issue date: 2000 May, 31 Cross reference:

I am using SuSE 10.2 with all updates applied. (kernel 2.6.18.8-0.3) IBM eserver xSeries 360 with quad Xeon 2ghz processors. 6 gb memory. Bios is up to date. When I boot SUSE without Xen the processor speed is reported at 2000 and the system clock keeps time correctly. When I boot the xenpae kernel Xen incorrectly reports a 2493.830 MHz processor. This causes the system clock to lose 12

Hello, I''m trying to install Xen3 on a server, but I can''t make the MegaRAID driver work. I''ve installed Debian Sarge, the stock kernel (2.6.8.2) works perfectly with the hardware. The SCSI RAID driver is megaraid. Hardware is : - IBM eServer xSeries 330 server - Dell PowerEdge RAID II controller I''ve recompiled the xen dom0 kernel (2.6.12.6) to include

Hello all I am trying to setup a backup system using Bacula on CentOS 6.7 installed on eserver x345 but cannot find the drivers Any help in finding the drivers will be much appreciated Regards Mustafa