similar to: xend start fails

I know, I know... don't use the non-standard kernels unless you have to... BUT: I have a D-Link N150 USB card. Bus 001 Device 004: ID 0846:9030 NetGear, Inc. WNA1100 Wireless-N 150 [Atheros AR9271] This isn't supported in C5, but it is supported in newer kernels (ath9k_htc). So let's try NDISwrapper: # rpm -i kmod\-ndiswrapper\-1.56\-1.el5.elrepo.i686.rpm

This is an abbreviated version of an e-mail that I also posted to the ndiswrapper mailing list. Compressing the long story, I ran into the same problem using CentOS 5 as I had with Fedora Core 6 and ndiswrapper: my laptop (HP Pavilion zv6000 series with a Broadcom BCM43xx wireless NIC) would lock up or spontaneously reboot after a few hours if I brought up the wireless interface. I also

Hi Folks, I'm trying tio install WLAN - USB - Stick Netgear WG111v3. ndiswrapper -i wg111v3 works. I can see ndiswrapper -l wg111v3: driver installed device (0846:4260) present But after modprobe ndiswrapper the system freezes. Troublshooting on ndiswrapper-sites says: It's a problem of "kernel is using 4K stacks (CONFIG_4KSTACKS)" Solution: recompile the kernel.

Hi everyone! :-) I have a problem with making a wireless USB dongle work under CentOS 6. The dongle is known to not work natively under Linux and last time I used it (cca 3 years ago) I managed to get it working using ndiswrapper. This time I was hoping to make it work again in the same way. But the "yum install kmod-ndiswrapper" reports the following (among other regular stuff):

WPA-2 (WPA Enterprise) fails with the new kernel(s) using ndiswrapper and wpa_supplicant. I haven't tried other authentication modes because that entails changes in the wireless setup which I am loathe to make right now. (It's a Broadcom mini pci card, so I have to use ndiswrapper with this Dell laptop. Bummer!). Rebuilding the newest wpa_supplicant rpm from the FC5 source rpm's

Greetings: I'm just installed Centos-4 on an IBM T-21 laptop. So far so good. Now I'd like to pop in a wireless lan adapter. I'm looking at a buying a Linksys WPC54G adapter (although I haven't done so yet). After doing some searching, it looks like the best way to get this card working is via ndiswrapper [http://ndiswrapper.sourceforge.net] and then to use Windoze

Hi - I'm trying to get wireless running on CentOS 4.7 on a dual core laptop (latitude-e4500) for an employee. I'm having trouble with building dkms-ndiswraper-1.54-1.el4.rf - enclosed are the errors messages. The kernel was rebuilt to disable CONFIG_4KSTACKS. The errors prior to rebuilding the kernel are identical to the errors after rebuilding the kernel and rebooting - minus the error

Hello, I tried to compile v2.3.1 on Solaris x86 with SUN Pro compilers. I had an error while stats libarary was being compiled and I notice that "-xtarget=generic64" was not passed to f95 while cc used it. Could you tell me how to fix this problem? f95 -PIC -O -I/mounts/devel/SUNWspro/prod/include -c sgram.f -o sgram.o f95 -PIC -O -I/mounts/devel/SUNWspro/prod/include -c

Hi Folks, I'd like to install my USB-WLAN-Stick Netgear WG111v3. Ndiswrapper works correct after installing Kernel-Modules from atrpm ndiswrapper-kmdl-2.6.18-53.1.19.el5.centos.plus-1.52-16.el5.i686.rpm. But by calling wpa_supplicant with wpa_supplicant -i wlan0 -D wext -c /etc/wpa_supplicant/wpa_supplicant.conf -d machine freezes. My wpa_supplicant.conf:

Hi people, I am using CentOs 4.3 and i'm trying to use ndiswrapper, but i don't obtain make it to run. my problem is with "invalid format" of module ? any suggestions ? thanks.

Has anyone had any luck with getting the Dell TrueMobile 1400 A/B/G wireless card working under Linux? I have experimented with ndiswrapper, i have had nothing but problems trying to get it to work. I was wondering if anyone has found a native Linux driver for the card. It uses a Broadcom 4309 chipset. Regards, Peter

Hi Folks, I am trying to get my wireless network card work under dom0 of XEN. I could successfully install the ndiswrapper drivers and could see it being associated to AP. However I amn''t able to transmit any packets outbound. I could''nt even ping the AP. Interestingly when I run a tcpdump I can see few broadcast packets on the interface. There no rules in iptables for nat or

Hi, I'm attempting to port an application which uses the Cypress CyAPI, which is Windows only, though I don't know if wine can handle device drivers or such low-level stuff. Anyway, I tried to develop a little prototype to run under wine, hoping it would provide with some insight. But this is the output I get: fixme:setupapi:SetupDiGetClassDevsW : returning empty list

I've just installed CentOS 5.3 on my Dell laptop and it seems to have detected and set-up my wireless card (BCM 4311) correctly as eth1. However, so far I haven't been able to activate it and have read the wiki http://wiki.centos.org/HowTos/Laptops/Wireless#head-320d6fcf09b7e16e0b15d19ef76adcb023a95938 which indicates that this card isn't actually supported in CentOS - but there has

Hi, I have a laptop DELL M90 with an Intel PRO/Wireless 3945ABG card. I'm using centOS 5.1 kernel 2.6.18-53 i386. I installed ndiswrapper v 1.52 I installed the driver http://ftp.us.dell.com/network/R164255.EXE The wireless-tools is v 28.2 When I trying to connect to my wireless access point with encryption key disabled everything work fine !!!! When I enabled the encryption key on my

Hi useRs, I'm trying to fit a basic AR(2) model with the 'ar' function. And when I try to check the value of the coefficients, I could not find the same value as the 'ar' function. Here is my example: myserie <- c(212, 205, 210, 213, 217, 222, 216, 218, 220, 212, 215, 236) #plot(myserie, type="l") myserieminus0 <- tail(myserie, -2) myserieminus1 <-

Hi useRs, I'm trying to fit a basic AR(2) model with the 'ar' function. And when I try to check the value of the coefficients, I could not find the same value as the 'ar' function. Here is my example: myserie <- c(212, 205, 210, 213, 217, 222, 216, 218, 220, 212, 215, 236) #plot(myserie, type="l") myserieminus0 <- tail(myserie, -2) myserieminus1 <-

Until recently, I was using POP on my desktop and imap to access my email on my phone and laptop. Got tired of not having everything everywhere, so decided to go full imap. Followed the suggestions online and created a new imap account for my site in Thunderbird and copied my pop folders over to the imap ones so that the emails would get uploaded to the dovecot server and Maildir folders. That

Hello. For couple of days ago i was searching google for some howto on installing Centos 5.3 on HP 2133 but i didnt found any. Since i have managed to install it on my HP 2133 i wrote on howto as well. I just need 2 things to be changed / defined better and its installing ndiswrapper (wich i did but im not so sure that i took right .rpms but it works), and second one is Installing 7zip on centos

Doing package development on a Windows 7 machine, and I want to tell R check not to worry about the "suggested" packages. I realize this can be done using the ~/.R/check.Renviron file, but what directory corresponds to "~"? Is that supposed to be the user directory? Or is it some other directory? I have this _R_CHECK_FORCE_SUGGESTS_=false (have also tried FALSE) in