similar to: Xen configuration

Hi, I have two Fedora box and rsync running on both systems. One system ip is 192.168.1.110 and the other is 192.168.1.71. I run manually for the following commands in both systems. my problem is whenever run it asking the user passwd and i cannot run the same automatically using crontab. My question is how to avoid the passwd option... rsync -aPrv rsync://192.168.1.110/detailing/

Hi I got a FC4 system running as Host.  Within this I loaded Suse 10 as a guest OS, the config file is as below: kernel = "/boot/vmlinuz-2.6.11.12-xenU" memory = 100 name = "suseguest" nics = 1 vif= [''mac=aa:00:10:00:00:10, bridge=xen-br0''] ip = "192.168.2.2" disk = [''file:/dev/hdc3,hdc3,w''] root = "/dev/hdc3 rw" extra =

Hi, When is start one vpn i get the following result: tinc10703003005 Link encap:Ethernet HWaddr C2:F7:7B:75:47:1A inet addr:192.168.3.20 Bcast:192.168.3.255 Mask:255.255.255.0 inet6 addr: fe80::c0f7:7bff:fe75:471a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX

Hi, I want to use samba as AD. everything seemed to be ok so far with the install and the config. STATUS=daemon 'smbd' finished starting up and ready to serve connections Feb 27 10:34:03 ip-1XX winbindd[22083]: [2020/02/27 10:34:03.002858, 0] ../lib/util/become_daemon.c:124(daemon_ready) Feb 27 10:34:03 ip-1XX winbindd[22083]: STATUS=daemon 'winbindd' finished starting up and

Hi, I have problem with a Centos 5.3 computer. The networking is very slow. The networking card is a RealTek 1GigE. I plugged an Ubuntu laptop on the same cable and port with an Intel GigE, and it's about 8 to 10 times faster. So the problem is likely to be with the CentOS config. Any suggestion on how to track down the problem with speed. I have checked the packets with wireshark, no

Hi, My local server is running CentOS 7. The machine has two NICs and is acting as a gateway. For DHCP and DNS, I'm using Dnsmasq. I have a strange little problem with local hostname resolution. Before going into more details, here's my configuration. [root at nestor:~] # ifconfig enp2s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.0.2 netmask

I have been having some problems setting up tinc on 2 masquerading linux slackware boxes. routerA is a NAT router to the internet, for two networks on two interfaces. This are the two networks: eth1 Link encap:Ethernet HWaddr 00:E0:4C:6C:6D:86 inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX

Hi All, I am facing an issue regarding communicating a value from outside to a Guest OS (linux, solaris and windows) launched on Xen Server. I did went through this thread, but It was not completely clear. http://lists.xensource.com/archives/html/xen-users/2006-07/msg00473.html My question is - Is there a way in Xen, through which I can communicate a value from outside to a Guest OS (linux,

Hi, I''ve setup a box with xen. For the root machine, it''s ok, it see the network card: alian@yoda:~> /sbin/lspci ... 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 Gigabit Ethernet Controller (rev 19) alian@yoda:~> lsmod .... sk98lin 208748 1 alian@yoda:~> /sbin/ifconfig eth0 Lien encap:Ethernet HWaddr 00:15:F2:39:D4:DF

Hi! I have a problem with my new Xen setup. I have installed Debian etch with netinstall and I''m using 2.6.18-6-xen-amd64 kernel in my dom0 and 3.0.3-0-4 version xen hypervisor. I''m using four network cards on my system and using three of them as xen bridges and dom0 is using the fourth one only for it''s own. So basicly both of my virtual servers use a network card

Greetings! I finally got the install done for a couple of gust OSs (Win 2003 server & Suse Enterprise 10) Bothe gusts are up and running, but - no networking. My setup: Hardware - AMD Athlon 4200+, ABIT Motherboard, 4 GB of DDR2 RAM, 2 onboard GB NICs Host OS- Suse Linux Enterprise server 10 Xen - 3.0.2_09749-0.4 Config file for Win 2003 server guest: # -*- mode: python; -*-

Hello, my current network setup looks like the following: dom2-eth0 (172.30.1.22) netmask /24 | | xen-br1 (no ip) | dom1-eth0 (172.30.1.21) netmask /24 dom1-eth1 (172.30.0.21) netmask /24 | | xen-br10 (172.30.0.1) netmask /24 | dom0 | | xen-br0 (normal IP) | eth0 (same IP as xen-br0) |

I am installed Xen 3.0 on a Fedora Core 4(2.6.12-1.1454_FC4xen0) machine. This machine is currently running one host domain: [root@]# xm list Name Id Mem(MB) CPU VCPU(s) State Time(s) Domain-0 0 128 0 1 r---- 49.1 fc4-vm1 1 63 0 1 -b--- 18.5 Following is the network configuration for Domain-0: eth0 Link

Greetings, I have two vms, one is a router and the other one is a client, for some reason, the client vm is unable get ip via dhcp from the router vm. here are outputs: vm1.xml: <interface type='bridge'> <mac address='52:54:00:54:78:be'/> <source bridge='virbr0'/> <model type='virtio'/> <address

Hi, I have a strange problem with my networking setup. I read all forums around the world where people had similar problems, but couldn''t find a solution. I have an Attansic L1 gigeth chip on my mainboard. This chip works OK in stock Ubuntu Gutsy (development) 2.6.22-9-generic kernel. When I boot into Xen, and after the bridge is created, the network stops working. Some info: - If I

Hello, There is a xen setup in which "brctl show" gives the following output. bridge name bridge id STP enabled interfaces eth1 8000.003048c9d4df no peth1 vif1.0 vif2.0

Hello, I have the following loop for two data sets: diveData_2008 and diveData_2009. It uses two other data: diveCond_all and fishTable. The problem is at the point to identify the dive_id for the given index (index is timestamp). It keeps on saying for the1st loop Error in fishReport$dive_id[i] <- dive_id : replacement has length zero for the 2nd loop Error in fishReport$dive_id[i + j] <-

I installed 64-bit xen 3.1.0 (from xensource.com tarballs) on three new machines today, using a configuration setup that I''ve used successfully many times before. However, I encountered a new problem. These are Dell Poweredge 1950 servers, by the way. >From lspci 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) 08:00.0 Ethernet

I am running Fedora 16 64bit and installed libvirt. I have the VM running with arm emulation with this one issue I can't figure out. I used Virtual Machine Manager to manage the VM and can access its console there. The Ethernet appears to be eth1 and the guest can set an IP on it etc. However, I cannot see any traffic from the Host when dumping any of the interfaces. I've tried

Hi, I tried this post on the Xen list first with no answer. I have 4 machines and 3 of which (all different) have no network access when booted into Xen. I tried using Fedora Core 8 and it produced the same results. Is it normal for the virbr0 interface to take an arbitrary IP? How does it decide what to use? An ifconfig when booted into Xen shows the following: eth0 Link encap:Ethernet