similar to: load_ocfs problem

# uname -r 2.4.21-20.ELsmp [root@hp2620-2 root]# rpm -qa | grep ocfs ocfs-tools-1.0.10-1 ocfs-support-1.0.10-1 ocfs-2.4.21-EL-1.0.13-1 [root@hp2620-2 root]# /sbin/load_ocfs /sbin/insmod ocfs node_name=hp2620-2-eth1 ip_address=10.1.2.101 cs=1913 guid=8D65C7CEECF9EBE638BD0013215BD6E9 comm_voting=1 ip_port=7000 insmod: ocfs: no module by that name found load_ocfs: insmod failed [root@hp2620-2 root]#

Looking for any ideas where I need to look to fix this: I'm installing RHEL3 AS (update 4) on Dell PowerEdge 6850's. I've installed the hugemem kernels on these boxes and need to install and run ocfs. Kernel: ------- 2.4.21-27.0.4.ELhugemem Loaded the ocfs rpm's --------------------- # rpm -qa | grep ocfs ocfs-2.4.21-EL-smp-1.0.14-1 ocfs-support-1.1.5-1 ocfs-2.4.21-EL-1.0.14-1

I have installed OCFS2 on two nodes SuSE 10. Seems all works superb and nice from the first sight. But, /dev/sda ocfs2 rac1 is not sharing through net (port 7777) with rac0. On both nodes I have 500Mb /dev/sda disks that are mounted (and are ocfs2). But they did not share the content with each other (files and folders in it). So when I am creating the file in one node I am expecting to

Hi All, I am getting this error after updating RHEL 3 Update 5 to update 8.. After upgrading OCFS loading get failed boot.log entries Nov 10 06:00:00 HHMEA load_ocfs: modprobe: Can't locate module ocfs Nov 10 06:00:00 HHMEA load_ocfs: load_ocfs: insmod failed Nov 10 06:00:01 HHMEA ocfs:  failed Nov 10 06:00:01 HHMEA mount: mount: fs type ocfs not supported by kernel I had given depmod

Well, I've compiled and installed Kernel 2.4.9-37 uniprocessor. I've made ocfs setup using version 1.0.9-9 uniprocessor. I've generated ocfs.conf using ocfstool. When I start ocfs using /etc/init.d/ocfs start, I receive the following errors: [root@RAC1 root]# /etc/init.d/ocfs start Loading OCFS: /sbin/insmod ocfs node_name=RAC1.localdomain ip_address=192.168.61 2 ip_port=7000

Hi. I'm running RHEL4 for my test system, Adaptec Firewire controllers, Maxtor One Touch III shared disk (see the details below), 100Mb/s dedicated interconnect. It panics with no load about each 20 minutes (error message from netconsole attached) Any clues? Yegor --- [root at rac1 ~]# cat /proc/fs/ocfs2/version OCFS2 1.2.0 Tue Mar 7 15:51:20 PST 2006 (build

Hi, We have a two node cluster running SLES 9 SP2 connecting directly to an EMC CX300 for storage. We are using OCFS(OCFS2 DLM 0.99.15-SLES) for the voting disk etc, and ASM for data files. The system has been running until last Friday when the whole cluster went down with the following error messages in the /var/log/messages files : rac1: Jul 7 14:56:23 rac1 kernel:

Hello, I want to use ocfs for a 10g RAC installation on a 2 node cluster, consisting of 1 Athlon and 1 Pentium machine with Firewire storage. OS is RHAS 3. Since I need to build my own binary Athlon rpm's, I downloaded ocfs-1.0.12.tar.gz ocfs-tools-1.0.10.tar.gz I was able to install both (./configure ; make - make install). When I try to load_ocfs I get lots of errors

I am receiving these errors when rebooting my system. Unmounting file systems: (1785) ERROR: unable to sendmsg, error=-101, Linux/ocfsipc.c, 394 (1785) ERROR: status = -999, Linux ocfsipc.c, 206 ocfs: Unmounting device (104,33) on rac1-priv1.collo.corp.net (node 2) (1785) ERROR: unable to sendmsg, error=-101, Linux/ocfsipc.c, 394 (1785) ERROR: status = -999, Linux/ocfsipc.c, 206 It

I followed your instruction to compile OCFS and received the following errors: [root@RAC1 ocfs-1.0.11]# ./configure --with-kernel=/usr/src/linux-2.4.9-e.38/linux checking build system type... i686-pc-linux-gnu checking host system type... i686-pc-linux-gnu checking for gcc... gcc checking for C compiler default output... a.out checking whether the C compiler works... yes checking whether we are

I successfully have OCFS running in a two-node RAC environment using RHAS 3 (2.4.21-4.EL) using Qlogic 2310 cards. IO performance, however, was terrible with the combination of OCFS and the Qlogic cards. After extensive testing, OCFS did fine on its own, as did the fibre cards. Put the two together, and everything literally ran twice as slow. Support at Qlogic pointed me to

As I said before, I'm not a linux expert. In which file of kernel source can I look for any missing code ? And specially what do I have to check ? __________________________________________ Mauro Staretz - MI Montreal Inform?tica Ltda Microsoft MCSE+I / MCDBA / MCP - Oracle OCP Tel: 55-21-2291-6116 R.2104 Fax: 55-21-2533-6028 __________________________________________ -----Mensagem

Hi, Is this "Unresolved Symbols" issue only occurring on VMware with e.38? We have OCFS users want to update their kernel to e.34 or e.38 without VMware. Please advise, Thanks! Roger--- -----Original Message----- From: Wim Coekaerts [mailto:wim.coekaerts@oracle.com] Sent: Friday, April 30, 2004 12:20 PM To: Sunil Mushran Cc: ocfs-users@oss.oracle.com Subject: Re: ENC: ENC:

Error: mount.ocfs2: Transport endpoint is not connected while mounting /dev/sdc1 on /u02, could not mount /dev/sdc1. The installation step is: 1. install all rpms on int-rac1, int-rac2 2. interconnect int-rac1, int-rac2, ping each other using private ip and public ip ok. Add EMC SAN as shared disk and visable for two nodes. 3. configure int-rac1 using ocfs2console, add two nodes 4. according

>also - for async io ; >p2448994_9204_LINUX.zip is the patch to apply for oracle >(this is metalink ARU patch number). Wim, The patch description on Metalink says: DIRECT IO SUPPORT ON EXT2 FILESYSTEM Which wasn't quite what I was expecting. Kevin -----Original Message----- From: Wim Coekaerts [mailto:wim.coekaerts@oracle.com] Sent: 25 November 2003 03:23 To: Brian M. Diehl

Hello list! Just pulled down ocfs2 this morning and installed it on two RHEL 4 2.6.9-34 systems. I have followed the manual, but am not seeing some things it describes and am not sure what the problem is. I guess my first question is - do I need to have a partition formatted as ocfs2 on all nodes in the cluster for this to work? I have formatted a partition via ocfs2console on node1, and

Hi, i dont seem to be able to get ocfs running on RH3 U8 32Bit [root@libra-devb-db1 root]# uname -a Linux devb-db1.mydomain 2.4.21-47.ELsmp #1 SMP Wed Jul 5 20:38:41 EDT 2006 i686 athlon i386 GNU/Linux [root@devb-db1 root]# cat /etc/redhat-release Red Hat Enterprise Linux AS release 3 (Taroon Update 8) [root@devb-db1 root]# rpm -ivh ocfs-2.4.21-EL-smp-1.0.14-1.i686.rpm Preparing...

I people, i install the ocfs in my virtual machine, with centos 5.3 and xen. But when i turn off the machine1, the ocfs start the fencing off the machine2. I read the doc in oracle.com, but could not solve the problem. Someone help? My conf and my package version. cluster.conf node: ip_port = 7777 ip_address = 192.168.1.35 number = 0 name = x1 cluster

Hi, I am trying to configure a two node cluster on SLES10SP2 using user level heartbeat. Here is my configuration. ocfs2-tools-1.4.0-0.3 **user level heartbeat** -> lsmod | grep ocfs ocfs2_user_heartbeat 20992 1 ocfs2_dlmfs 37776 1 ocfs2_dlm 204456 1 ocfs2_dlmfs ocfs2_nodemanager 223384 6 ocfs2_user_heartbeat,ocfs2_dlmfs,ocfs2_dlm configfs 44700 3 ocfs2_user_heartbeat,ocfs2_nodemanager

Hi , I am getting the error "No space left on device" on a device with free space which is ocfs2 filesystem. Additional information is as below, [root at sai93 staging]# debugfs.ocfs2 -n -R "stats" /dev/sdb1 | grep -i "Cluster Size" Block Size Bits: 12 Cluster Size Bits: 15 [root at sai93 ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release