similar to: Growing a zpool mirror breaks on Adaptec 1205sa PCI

I''m in well over my head with this report from zpool status saying: root # zpool status z3 pool: z3 state: DEGRADED status: One or more devices has experienced an error resulting in data corruption. Applications may be affected. action: Restore the file in question if possible. Otherwise restore the entire pool from backup. see: http://www.sun.com/msg/ZFS-8000-8A

I thought I recalled reading somewhere that in the situation where you have several zfs filesystems under one top level directory like this: rpool rpool/ROOT/osol-112 rpool/export rpool/export/home rpool/export/home/reader you could do a shapshot encompassing everything below zpool instead of having to do it at each level. (Maybe it was in a dream...)

I''ve got knee deep into learning how to use Opensolaris and zfs, and I see now that my goal of home zfs server may have been better served if I had partitioned the install disk leaving some of the 60GB to be added to a zpool. First, how much space does a working OS need. I don''t mean bare minimum but to be comfortable and have some growing room (on the install disk)?

Hi, Does anybody has any experience with e-sata on CentOS5.2? - How fast is it? Same as an internal sata? - Does it support sata-2? - Does it "hot-plug" like a USB? -- Thanks http://www.911networks.com When the network has to work

Adaptec 1210SA with a RAID 0 Intel 815 based mobo 512mb ram During the install, Disk Druid or whatever the partition utility is, sees the first disk but says the other disk is not initialized and only reports 150MB when the array is 300MB. How do I get the CentOS installer to see the RAID 0 array correctly?

This may be a bit poorly thought through but in this case I don''t really know enough to really think it through. My back ground is linux... there I used a tool called rsnapshot which used rsync and some hardlink magic to create versioned backups. But take very little space. By versioned I don''t mean as in version control but just copies of files as they change. It worked by

Hi everyone, I'm looking into setting up a SATA hardware raid, probably 5 to use with CentOS 4. I chose hardware raid over software mostly because I like the fact that the raid is transparent to the OS. Does anyone know of any SATA controllers that are well tested for this sort of usage? From what I can tell from googling, this is more or less where RHEL stands: Red Hat Enterprise Linux

Hi List I have a Promise SATA 300 TX ( NOT raid ) that do have RHEL4 driver, but this driver doesn?t work with CentOS4 Why? What can I do to get a driver that works? SATAII150/SATA300 TX series RHEL4 32-bit Driver http://www.promise.com/support/download/download2_eng.asp?productID=139&cate gory=all&os=100# This one should be for the correct 2.6 kernel, but it's

I know that this has been well-discussed already, but it''s been a few months - WD caviars with mpt/mpt_sas generating lots of retryable read errors, spitting out lots of beloved " Log info 31080000 received for target" messages, and just generally not working right. (SM 836EL1 and 836TQ chassis - though I have several variations on theme depending on date of purchase: 836EL2s,

I''m hoping to get some general clues about what all is required to get an experiment going with zfs. I''ve managed to install osol-11 in a vmware on windowsXP host from a recent *.iso. I''m following along with Simon''s blog showing how to set up ZFS. I''m newbie with both ZFS and Solaris but the instructions seem pretty clear. However I''m

Hello there, I spent all day yesterday trying to get a small data set from Splus into R, no luck! Both, Splus and R, are run on a 64-bit RedHat Linux machine, the versions of the softwares are 64-bit and are as what follows: Splus: TIBCO Software Inc. Confidential Information Copyright (c) 1988-2008 TIBCO Software Inc. ALL RIGHTS RESERVED. TIBCO Spotfire S+ Version 8.1.1 for Linux 2.6.9-34.EL,

Hi: I've tried to install centos 4.3 in a raid array, setuped on bios as mode "Adaptec". The chip is ICH7R but centos always sees 2 drives instead of the array that I create. I've contacted Supermicro support and they gave me this link ftp://ftp.supermicro.com/driver/SATA/Adaptec_ICH7R/Linux/Redhat/ , but the disk drivers I tried to use with centos 4.3 did not work, saying that

I have a simple mirror pool with 2 disks. I pulled out one disk to simulate a failed drive. zpool status shows that the pool is in DEGRADED state. I want syslog to log these type of ZFS errors. I have syslog running and logging all sorts of error to a log server. But this failed disk in ZFS pool did not generate any syslog messages. ZFS diagnosists engine are online as seen bleow. hrs1zgpprd1#

Hi, What are the most stable sata raid cards for centos. Looking at sata raid1 setup. Kind Regards, Imran ************************************* This electronic transmission is strictly confidential and intended solely for the addressee. If you are not the intended addressee, you must not disclose, copy or take any action in reliance of this transmission. *************************************

Can anyone tell me if/when the Adaptec AIC9410 SAS/SATA controller will be supported? Michael Grant

This morning we got a fault management message from one of our production servers stating that a fault in one of our pools had been detected and fixed. Looking into the error using fmdump gives: fmdump -v -u 90ea244e-1ea9-4bd6-d2be-e4e7a021f006 TIME UUID SUNW-MSG-ID Oct 22 09:29:05.3448 90ea244e-1ea9-4bd6-d2be-e4e7a021f006 FMD-8000-4M Repaired

I have just built a new SunFire X4100 server with an Adaptec 2230SLP RAID card using FreeBSD 6.2-PRE kernel (from September 20). Everything is working extremely well except I cannot run the aaccli utility on this controller. When I try to open the controller, it gives this error: Command Error: <The current AFAAPI.DLL is too old to work with the current controller software.> On

Has anyone on the list used one of these w/Linux? We currently use Linux + Cinelerra for editing uncompressed video (and a few dual G5 macs running Final Cut Pro). Current editing stations are getting a bit long in the tooth so I've been mulling over a mass upgrade. 8-) These cards are interesting to me because they are PCI-X and support 4 SATAII drives per multilane/infiniband

I am curious why zpool status reports a pool to be in the DEGRADED state after a drive in a raidz2 vdev has been successfully replaced. In this particular case drive c0t6d0 was failing so I ran, zpool offline home/c0t6d0 zpool replace home c0t6d0 c8t1d0 and after the resilvering finished the pool reports a degraded state. Hopefully this is incorrect. At this point is the vdev in question now has

Last week we tried to install Centos on a brand new HP ML150 G2 with AIC-8130/ Marvell SATA Raid card and it was a no go. We tried a few other flavors of Linux as a test and all had trouble as well. Unfortunately time didn't permit so we opted for a Windows solution to get the box into production. We have never had a problem with IDE and Embedded SATA (Non Raid) Next time we want to