similar to: 7.2-PRERELEASE/sunx2200/bge/msi broken

Hi, this server, a Dell R720 has 4 bge on board, Broadcom NetXtreme Gigabit Ethernet, ASIC rev. 0x5720000 bge0: APE FW version: NCSI v1.1.7.0 bge0: CHIP ID 0x05720000; ASIC REV 0x5720; CHIP REV 0x57200; PCI-E miibus0: <MII bus> on bge0 ... I have connected the ethernet to port labeled 0, but it appears as bge2, how can this be corrected? thanks, danny

Hi, I'm having lots of difficulties with BCM5719, which is the default network card of HP Proliant DL 360 G8 servers. I can get a few ping replies before I get a couple of these: bge0: watchdog timeout -- resetting bge0: watchdog timeout -- resetting Then everything hangs. Can not log in using ssh.

latest pxeboot (7.1): mother-board NIC/LOM CPU ------------- ------- --- Intel SWV25 em xeon works fine SUN X2200 bge amd works fine DELL PE 2950 bce xeon failes 95% of the times hangs or goes into btx dump regs. mode :-) Intel SE7320VP21 msk xeon failes 50% of the times - hangs pxeboot with btx.S 1.45 2008/02/27 23:35:39, works fine. so it seems that changes since 1.45 have

Sorry for the cross-post, but this could be either lists problem. I have 2 boxes running 7-STABLE as of 20081130, both i386 SMP. One is running ISC DHCPD 3.0.x from recent ports, and the other dhclient from make world. The server is refusing to answer the DISCOVER request, as it thinks the IP checksum is wrong, which tcpdump also confirms. Other DHCP clients are working fine on this network,

Hello! I have Compaq DL360G2 with Broadcom BCM5701 Gigabit Ethernet and FreeBSD 5.1R installed. There are no problems if I use bge as usual network card, but when I try to use 802.1Q vlans, I can't receive (only receive, sending is ok) packets more then 1456 bytes! What is the problem? BGE driver, VLAN driver or my network configuration? Best wishes, Boris

I opened a bug report earlier today but it doesn''t seem to have been added to the bugs database. I''m posting here in case one of the Crossbow developers might see it and confirm this behavior. Description Duplicate packets are generated whenever an aggregate is introduced into the network configuration. We''ve ruled out switch ports and physical bge interfaces as

Recent SUP. Installed on Dell PowerEdge 4600. Getting tons of: Sep 30 12:23:16 zige /kernel: bge0: gigabit link up Sep 30 12:23:46 zige last message repeated 98 times Also getting some TCP retransmits. This causes noticable delays in pretty much everything I do now. Not a problem prior to the SUP. I was on 4.8-STABLE before. When pulling/replacing cables, it went into a mode where it would

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I'm trying to run a QEMU VM on top of a FreeBSD 7.x server ... I've tried the exact same setup on my desktop, using 192.168.1.x and an fxp device, and it all works perfectly, but as soon as I do this on another machine on a public IP, I'm not getting any routing, I can't even ping it from the same machine ... My first thought was

I'm experiencing similar problems with a 3C996-T under 4.8-REL. In particular, connecting a 4.8-REL machine to a 5.1-REL machine leads to some interesting situations: I can do simple pings across the link, but ssh fails, and heavy pings crash the 4.8 machine. Similarly changing the interface configuration with ifconfig tends to crash the 4.8 machine (mtu, link0, up/down, etc). The

Hi all, Over the last month or so I've installed FreeBSD 9 (-stable) on several Mac Minis via the memstick image; they seem to be pretty good little boxes for things like offsite secondary nameservers, for example, and they're easily replaced in case of problems. However, the newest minis have slightly different hardware, and FreeBSD can't find the built-in NIC. pciconf -lv on the

After the interesting revelations about the X2100 and it''s hot-swap abilities, what are the abilities of the X2200-M2''s disk subsystem, and is ZFS going to tickle any wierdness out of them? -brian -- "The reason I don''t use Gnome: every single other window manager I know of is very powerfully extensible, where you can switch actions to different mouse buttons.

after rebooting I get very often: ... mfi0: COMMAND 0xffffff800132d990 TIMEOUT AFTER 659 SECONDS mfi0: COMMAND 0xffffff800132d990 TIMEOUT AFTER 689 SECONDS mfi0: COMMAND 0xffffff800132d990 TIMEOUT AFTER 719 SECONDS ... another reboot usualy fixes this. danny

I am running bsnmpd with basic snmpd.config (only community and location changed). When there is a problem with HDD and disk disapeared from ATA channel (eg.: disc physically removed) the bsnmpd always dumps core: kernel: pid 1188 (bsnmpd), uid 0: exited on signal 11 (core dumped) I see this for a long rime on all releases of 7.x and 8.x branches (i386 and amd64). I did not tested 9.x. Is

Hi. I got this on today's RELENG_6 with Broadcom BCM5722 A0, ASIC rev. 0xa200. >From dmesg (bge related): bge0: <Broadcom BCM5722 A0, ASIC rev. 0xa200> mem 0xe8400000-0xe840ffff irq 16 at device 0.0 on pci2 bge0: firmware handshake timed out, found 0x4b657654 bge0: firmware handshake timed out, found 0x4b657654 bge0: EEPROM read timed out bge0: failed to read EEPROM device_attach:

I have built up a simple allication for web service interaction. But the following error message occured: uninitialized constant HelloadminController::HelloApi service api class HelloApi < ActionWebService::API::Base api_method :getMsg, :expects => [:name=>:string], :returns => [:string] end service controller class HelloController < ApplicationController

Hi, on 2 different servers, running 7.1-stable + zfs, I get this error rather frequently: Feb 5 17:01:03 warhol-00 kernel: impossible packet length (543383918) from nfs server sunfire:/dist Feb 5 17:01:03 warhol-00 kernel: impossible packet length (1936028704) from nfs server sunfire:/dist Feb 5 17:01:03 warhol-00 kernel: impossible packet length (1869363744) from nfs server sunfire:/dist

Author: mabloom Repository: /hg/zfs-crypto/gate Revision: 39c5623029b347adbf2ab92400d25328f7b321ee Log message: 5084264 Error messages output when configure jumbo frames using bge.conf Files: update: usr/src/uts/common/io/pci_pci/pci_pci.c

Hello! Please, help me, I''m totally lost choosing basic budget server for XEN. The variants are Sun (X2200 M2 or Sun X2250 M2) or maybe HP Proliant DL160 G5p. Or maybe some IBM server? Which X2200 configuration will perform better, two Opteron dual-core 22xx or single quad-core 23xx? Which one performing better nowadays, Opteron or Xeon? I know that 2-3 years ago Opteron was the

Hello, I need some advice how to debug this issue ... Recently I got a new mainboard for a router, it's a Gigabyte GA-H77N-WIFI with two onboard re(4) NICs. The problem is that re0 works fine and re1 doesn't: It doesn't receive any packets. Tcpdump displays all outgoing packets, but no incoming ones on re1. Ifconfig shows the link correctly (100 or 1000 Mbit, depending on where I

How do I create a vnic that represents the factory assigned MAC address of my physical nic? The bge device in my system (x2100) appears to support 4 MAC addresses. The driver reserves the first as the ''primary/default'' address and allows manipulation of the other three via the MAC_CAPAB_MULTIADDRESS interface. I''d like to use vnics on this system, as I have Xen guest