similar to: bge0: EEPROM read timed

I'm experiencing similar problems with a 3C996-T under 4.8-REL. In particular, connecting a 4.8-REL machine to a 5.1-REL machine leads to some interesting situations: I can do simple pings across the link, but ssh fails, and heavy pings crash the 4.8 machine. Similarly changing the interface configuration with ifconfig tends to crash the 4.8 machine (mtu, link0, up/down, etc). The

Hi, I'm having lots of difficulties with BCM5719, which is the default network card of HP Proliant DL 360 G8 servers. I can get a few ping replies before I get a couple of these: bge0: watchdog timeout -- resetting bge0: watchdog timeout -- resetting Then everything hangs. Can not log in using ssh.

I opened a bug report earlier today but it doesn''t seem to have been added to the bugs database. I''m posting here in case one of the Crossbow developers might see it and confirm this behavior. Description Duplicate packets are generated whenever an aggregate is introduced into the network configuration. We''ve ruled out switch ports and physical bge interfaces as

Recent SUP. Installed on Dell PowerEdge 4600. Getting tons of: Sep 30 12:23:16 zige /kernel: bge0: gigabit link up Sep 30 12:23:46 zige last message repeated 98 times Also getting some TCP retransmits. This causes noticable delays in pretty much everything I do now. Not a problem prior to the SUP. I was on 4.8-STABLE before. When pulling/replacing cables, it went into a mode where it would

Hi, this server, a Dell R720 has 4 bge on board, Broadcom NetXtreme Gigabit Ethernet, ASIC rev. 0x5720000 bge0: APE FW version: NCSI v1.1.7.0 bge0: CHIP ID 0x05720000; ASIC REV 0x5720; CHIP REV 0x57200; PCI-E miibus0: <MII bus> on bge0 ... I have connected the ethernet to port labeled 0, but it appears as bge2, how can this be corrected? thanks, danny

Hi all, Over the last month or so I've installed FreeBSD 9 (-stable) on several Mac Minis via the memstick image; they seem to be pretty good little boxes for things like offsite secondary nameservers, for example, and they're easily replaced in case of problems. However, the newest minis have slightly different hardware, and FreeBSD can't find the built-in NIC. pciconf -lv on the

Well this is new. I haven't a clue what Dell has done on this R620, but this popped up today after I did a boat load of BIOS updates and tried to install stable/9 from our yahoo tree. If anyone sees the obvious solution here, I'd love to figure it out. found-> vendor=0x14e4, dev=0x165f, revid=0x00 domain=0, bus=2, slot=0, func=1 class=02-00-00, hdrtype=0x00, mfdev=1

Hi, I have a server (Dell PowerEdge SC1435, ServerWorks HT1000) on which I'd like to try installing FreeBSD. I've already failed to make 7.0 work on this box and was wondering if you have information about the behavior of the upcoming 7.1 on this hardware. I've been following the "HT1000 chipset errata saga" thread, and the commits by sos@ to CVS (around Jan 2008), but have

Hi, Can you tell why my vnic built on top of an aggregation of 2 NICs of 1 Gbit/s doesn''t report a speed of 2 GBit/s ? [root at nazgul /]# dladm show-dev bge0 link: up speed: 1000Mb duplex: full bge1 link: down speed: 0Mb duplex: unknown bge2 link: down speed: 0Mb duplex: unknown bge3 link: down speed: 0Mb

(networking-discuss Bcc''ed) Good morning, The Crossbow team would like to invite you to participate in the project''s third and last phase of code review. The third phase of the review starts today, and will last for two weeks. It covers the following parts of the code: VLANs Link Aggregations Xen mac_datapath_setup All drivers

Hi, how can ip instances be used with vlans ? Is that possible ? I don''t know how to configure this, if I only have one interface (e.g. bge0), and want to assign e.g. bge1000 to a zone. Any cookbooks available ? Thanks Detlef

Hi, I am trying to install centos 5.3 on ibm x3200 m2 server. The problem appears when the installer is about to finish the installation. It detects the RAID correctly, but it doesn't finish formatting the root partition. I tried the default partition layout and also a custom one, but it always ends with the same message: An error occurred trying to format /. this problem is serious and the

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello All, I have had a problem detecting the network card on my notebook when ACPI is enabled for a year. The problem still exists in 7.1-RELEASE. with ACPI: ... bge0: <Broadcom NetLink Gigabit Ethernet Controller, ASIC rev. 0xb002> irq 17 at device 0.0 on pci8 bge0: 0x10000 bytes of rid 0x10 res 3 failed (0, 0xffffffff). bge0: couldn't

Hi, between March 16 and now, bge on a Sun X2200 stopped working, turning off msi (via hw..pci.enable_msi=0) got it working again. I tried first replacing bge with an older version but that did not help. please advice :-) Danny

How do I create a vnic that represents the factory assigned MAC address of my physical nic? The bge device in my system (x2100) appears to support 4 MAC addresses. The driver reserves the first as the ''primary/default'' address and allows manipulation of the other three via the MAC_CAPAB_MULTIADDRESS interface. I''d like to use vnics on this system, as I have Xen guest

Hello Got strange problem with high system "%system load" and very slow user level programs (apache+php+mysql) behavior gstat shows 1.5-4% hard disk busy load but system shows about 20-30% load while user load is max 5%. vmstat shows from 2 to 35 process in "b" state. Now use 7.0-RELEASE-p5 , but the same problem was with 7.0-RELEASE. And have no idea what to do with this.

Has anyone gotten a transparent firewall working? I''m using snv_125 on an IBM x346 (snv_130 goes into endless boot loops on this hardware). I can create a working bridge with dladm, but can''t stop packets, even with "block in quick all". That stops packets on my management interface bge0, but not on the bridge. :( tim at ghost:~# ifconfig -a lo0:

I have a broadcom bcm5722 and a dual intel pro/1000 pt nic in a dell t110. The setup sees the cards and i put them into automatic mode. After the install no cards are detected at all. Astaro 8.01 detects and utilizes all of these cards just fine. I have also tried ubuntu server 10.04 lts and they work fine. I'm curious if this is a bug with Centos 6?

Hello! I have Compaq DL360G2 with Broadcom BCM5701 Gigabit Ethernet and FreeBSD 5.1R installed. There are no problems if I use bge as usual network card, but when I try to use 802.1Q vlans, I can't receive (only receive, sending is ok) packets more then 1456 bytes! What is the problem? BGE driver, VLAN driver or my network configuration? Best wishes, Boris

I''m running a nevada b99 guest on a nevada b99 host. The guest is configured as a dhcp client. When I snoop in dom0 while the guest boots, I see two back-to-back DHCPREQUEST packets issued by the guest. The first of the two packets has an empty UDP checksum; otherwise they seem identical. Is this a bug? Fred Oliver ETHER: ----- Ether Header ----- ETHER: ETHER: Packet 246 arrived