similar to: Confusion on Primary and Secondary

Hello and welcome, Can you please point to any online "PiNUT" docs, if that is a project name? I did not find anything that looked specific to the key word. In any case, the "primary" role of upsmon applies to any UPS that it is connected to and can directly manage, so in case of a power outage it tells everyone else (secondaries) to shut down first, and then runs the UPS

hi: when testing nut in our environment, we found something that nut maybe tune for "stale/dead ups" situation. currently the "dead ups" are assume alive(eg: host shutdown unnecessary), unless it is in the "OB" state before going to stale. our environment (ServerA + ServerB forms a cluster): ServerA-> usb to UPSA -> two PS power by UPSA and UPSB

Hello NUT Team! I continue playing with NUT for Windows and USBHID-UPS driver I've got from Frederic to fix "Data Stale" problem. It seems there is something wrong when Network UPS Tools service is starting with disconnected USB cable. UPSMON is writing "Data Stale" to output and continue do it infinitely, even the cable is connected back. Here is a short log: Network

Hello NUT Team! I am testing the early shutdowns in NUT 2.6.5-1 package for Windows (Windows 7 x64). My configuration files: upsmon.conf RUN_AS_USER upsmon MONITOR upsa at 192.168.10.200 1 upsmon pass master MINSUPPLIES 1 SHUTDOWNCMD "/sbin/shutdown -h +0" NOTIFYCMD "upssched.exe" POLLFREQ 5 POLLFREQALERT 5 HOSTSYNC 15 DEADTIME 15 POWERDOWNFLAG

Hello! I tried NUT 2.6.5-1 (Windows port) with my APC Back UPS ES. It seems I have configured NUT properly, nut-scanner found my UPS: [nutdev1] driver = "usbhid-ups" port = "auto" vendorid = "051D" productid = "0002" product = "Back-UPS ES 525 FW:851.t3.I USB FW:t3" serial = "8B0745R23575

OS: Raspbian Lite 4.19 (Linux 5.4.51-v7l+ armv7l) NUT version: 2.7.4 Install Method: Package (apt-get) Device Name: CyberPower CP1500PFCLCD, connected via USB Problem: This is a brand-new installation; the only step I've taken is my initial edit of /etc/nut/ups.conf (which I'll post below). I started the driver and after doing so issued a reboot command to my Raspberry Pi (sudo reboot).

?Hello, There is a new intermediate Windows binaries release available at : http://www.networkupstools.org/package/windows/NUT-Installer-2.6.5-3.msi This fixes a regression about stopping the NUT service. Feedback is highly appreciated. Regards, Fred -- Eaton Opensource Team - http://opensource.eaton.com ----------------------------- -----------------------------

Hi, I'm trying to talk to an old Masterguard UPS A3000 so I can determine current load and status etc, to determine the best replacement options. After a fair amount of google fu, and attempting different things, this is where I have ended up. First, environment: OS: Linux (Debian Stable) NUT Version: 2.7.2-1 (Debian unstable package) UPS details (on the rear lable): Manufacturer:

On Jan 21, 2014, at 8:05 AM, Rafa? Oleszek wrote: > MONITOR UPS_251 at localhost 2 monmaster password master > MONITOR UPS_252 at localhost 2 monmaster password master I think the "2"s here should be "1". "powervalue is an integer representing the number of power supplies that the UPS feeds *on this system*." So if UPS_251 is connected to one power supply on

> What do your configuration files look like? Setting MINSUPPLIES to 2 should work. You can run upsmon with a debug level of 3 or greater, and it will print the current and minimum "power value", which is what determines when to shut down. > > Also, if you don't want to wait for both UPSes to drain to the low battery state, you can set up a pair of dummy-ups drivers. I'm

Hi Team While i;m searching on the internet about UPS SNMP monitoring , I found this NUT server. Thank God, But sad news is that my UPS is not listed in the compatibility list. But I download NUT server on my ubuntu node and just discover it sudo /lib/nut/snmp-ups -DD -a ups unfortunately got the below error message. 228.253598 [D2] Testing ups.model using OID 1.3.6.1.2.1.33.1.1.2.0

On Jan 21, 2014, at 3:16 AM, Rafa? Oleszek wrote: > I would like to mention that MINSUPPLIES manipulation doesn't work. My nut version is : 2.2.2-4 (RHEL 5) What do your configuration files look like? Setting MINSUPPLIES to 2 should work. You can run upsmon with a debug level of 3 or greater, and it will print the current and minimum "power value", which is what determines

Hi, Another beginner question. I spend hours trying to find the solution for how to configure winnut properly but I' struggling to make it work. I want my QNAP NAS TS-231 to work as a master and send signal to the PC to shut it down during power outage. I configured QNAP properly (like this: http://geekbeat.tv/qnap-adding-external-devices-qnap), but I don't know what to do next. I work

On Jan 21, 2014, at 8:05 AM, Rafa? Oleszek wrote: > It does not matter what value I'll put in MONITOR and MINSUPPLIES line. NUT not waiting for both UPS to start timer. Correct. You can think of upssched as operating on raw UPS status, rather than the calculated powervalue that upsmon uses to decide when to shut down. -- Charles Lepple clepple at gmail

Hello, I'm trying to communicate with a MGE Pulsar STS 16 using nut under Linux, but I've had no luck so far. I haven't saw it supported in the doc, so if there's anything I can try... Thanks, Arnaud. -- Perso: http://launay.org/blog/ H?bergement: http://www.nocworld.com/

Hi, What shoud I do in order to configure NUT to perform only monitoring, I mean to not shutdown anything at all? Thanks in advance! -- -- Sergio Belkin LPIC-2 Certified - http://www.lpi.org -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.alioth.debian.org/pipermail/nut-upsuser/attachments/20160518/23c72ff1/attachment.html>

> On Jan 21, 2014, at 9:24 AM, Rafal Oleszek wrote: > >> I tried all options: >> 1,2 >> and in MINSUPPLIES: 1,2,3,4 >> still didn't work. > > My mistake - I gave you the wrong advice before. For MINSUPPLIES, I'm used > to either a 1:1 UPS-to-server ratio, or 2:1 where the server can run with > either power supply unpowered. > > I just tried

HI all How to setup nut to use and monitor laptop battery on linux? (/proc/acpi/battery/BAT0/state) Emard

On Jan 21, 2014, at 9:24 AM, Rafal Oleszek wrote: > I tried all options: > 1,2 > and in MINSUPPLIES: 1,2,3,4 > still didn't work. My mistake - I gave you the wrong advice before. For MINSUPPLIES, I'm used to either a 1:1 UPS-to-server ratio, or 2:1 where the server can run with either power supply unpowered. I just tried this in upsmon.conf: MONITOR dummy1 1 monuser

Hi, I'm trying to get a sweex ups working with nut on debian sarge. This one: http://www.sweex.com/producten.php?lang=1&%20sectie=&item=59&artikel=95 It's shipped with UPSmart and according to the compatibility list it should work with the genericups upstype=7 driver. But it doesn't. I get: mybox:/etc/nut# /etc/init.d/nut start Starting Network UPS Tools: (upsdrvctl