similar to: XCP documentation?

My UPS is an Exide NetUPS SE PRC1500i (1500 VA), also known as Powerware 5119, according to Karl Schmidt (http://lists.alioth.debian.org/pipermail/nut-upsuser/2005-July/000026.html) also Deltec PowerRite Pro II, and according to http://www.usedups.de/compaq_ups.html also Compaq R3000h. I am not sure if the information in http://www.bps.hu/powerware/model_en.html is to be interpreted as that it was

My UPS is an Exide NetUPS SE PRC1500i (1500 VA), also known as Powerware 5119, according to Karl Schmidt (http://lists.alioth.debian.org/pipermail/nut-upsuser/2005-July/000026.html) also Deltec PowerRite Pro II, and according to http://www.usedups.de/compaq_ups.html also Compaq R3000h. I am not sure if the information in http://www.bps.hu/powerware/model_en.html is to be interpreted as that it was

On Feb 12, 2014, at 7:50 PM, Tim Dawson wrote: > Run the driver with -DDDDD and see what variables it picks up. I have noted that with the Prestige 9 in bcmxcp, some variables are not consistent within models, and had to do some gentle remapping to get things to work correctly. Tim, is this the issue you mentioned on 2014-02-02 with blocks 0x9 and 0x13? I'll reply to that email. > On

On 13/02/14 12:16, Charles Lepple wrote: > On Feb 12, 2014, at 7:50 PM, Tim Dawson wrote: > >> Run the driver with -DDDDD and see what variables it picks up. I have noted that with the Prestige 9 in bcmxcp, some variables are not consistent within models, and had to do some gentle remapping to get things to work correctly. I ran the new driver (see below) and with -DDDD it throws out

Hi, I've got a Powerware Prestige 9 1kVA UPS that seems to not be working with nut. It's not in the current "supported hardware" list, but the old bcmxcp page lists it as being a UPS that speaks that protocol. I have the following in my ups.conf [powerware] driver = bcmxcp port = /dev/ttyS0 desc = "Powerware Prestige 9 EXT" baud_rate = 2400 And when I start the

Run the driver with -DDDDD and see what variables it picks up. I have noted that with the Prestige 9 in bcmxcp, some variables are not consistent within models, and had to do some gentle remapping to get things to work correctly. - Tim On 02/12/2014 06:46 PM, Greg Vickers wrote: > Hi all, > > I've hooked up an Eaton Powerware 5110 to Ubuntu 13.10 server, and > configured nut

Looking for Powerware Prestige 9 Series 6000VA. If you know where I can buy one please respond. thanks!

Hi all, I've hooked up an Eaton Powerware 5110 to Ubuntu 13.10 server, and configured nut appropriately. The cgi scripts are working fine, but on upsstats.cgi, the Batter, UPS Temp and Battery Runtime fields are all blank - and there are no entries for these values in the 'All data' tree. I've checked the man page for bcmxcp_usb

I noted some correspondence from several years back about supporting this device with bcmxcp, and the problems therein. Since I have one of these UPS units, still going strong, and the Eaton LanSafe stuff has finally caused me enough grief to abandon it, I figured I'd take a look at this. The issue is not that bad - the bcmxcp driver query of the topology block (2 bytes!) is returning

Adam: Thanks for putting up this page. But something is wrong. In particular, our Powerware 9135 is a three phase UPS system with THREE 480 volt outputs. So the displayed voltage is not correct -- in fact there should really be THREE voltages displayed, all around 480v. Nut developers: I am copying the NUT mailing list to see if anyone can suggest how to fix this. NUT developers, see the

Hi all, I've more-or-less got NUT 2.0.4 working with my Powerware Prestige 1000VA UPS (serial), but unfortunately NUT is flagging LOW_BATTERY continuously, which is a tad embarrassing when power fails ;-) The numbers from upsc blah at localhost seem reasonable: ambient.temperature: 24.5 battery.charge: 99 battery.runtime: 3999 battery.voltage: 69.2 driver.name: bcmxcp

Someone might want to add this to the docs - cable list and compatibility list - took me way to long to find. I was trying to find information on my UPS and came up with the following names for the same UPS series. Powerware 5119 Exide name was NetUPS SE Deltec name was PowerRite Pro II (1000VA-3000VA) What I have: The Exide NETUPS SE model PRC2400a p/n 05144038-3904 OUTPUT 2400VA 1600 WATTS

During the last month, I've been integrating a Powerware 5115 into an embedded system by writing a custom NUT daemon. This work has gone quite well and NUT has been very helpful, but it sure would be nice to have some additional instcmds for the 5115. The bcmxcp driver comments mention "manuals for the BCM/XCP". I'm wondering if I could get a copy of those so that I might

Hi I have the following UPS : ups.mfr: Eaton ups.model: POWERWARE UPS 500i ups.power.nominal: 500 It is using the bcmxcp_usb driver. I started the driver with debug options, and noticed the following for the meter map : 0.475625 0027 0000 51 output.frequency 0.475634 0028 0004 51 input.frequency 0.475641 0033 0008 51 battery.voltage

On Feb 28, 2014, at 1:05 PM, Tim Dawson wrote: > Git: > > Network UPS Tools - BCMXCP UPS driver 0.28 (2.7.1) > RS-232 communication subdriver 0.20 > > > 2.7.1: > > Network UPS Tools - BCMXCP UPS driver 0.26 (2.6.5-3857M) > RS-232 communication subdriver 0.20 > > > I'm not so much noting the "2.6.5" in the dev, but the 0.28 vs 0.26 bcmxcp

Hallo, I own a NETUPS 450 (Model on the sticker: PRM 450i; upsstats reports "UPS 450 VA FW -0024") which perfectly works with the upscode2 driver. Maybe you want to add it to your list, even if the model is >10 years old. I suppose this is true for the whole series. According manual the come in the 450VA, 700VA, 1000VA and 1500VA strengths. They have been sold under different

The driver will poll the UPS for what variables it supports when it starts, and then go into a polling loop. Look for a section defining the meter map, and you should see the result, as well as the raw data. You can get the comm spec for XCP from the nut site if you want to delve deeper. I'd give more specifics, but am out of town and only working from memory at the moment . . . - Tim On

I'm trying to get a Powerware 5125 UPS running using the bcmxcp driver, but I get the following errors: video2:~# /sbin/upsdrvctl start Network UPS Tools - UPS driver controller 2.0.4 Network UPS Tools - BCMXCP UPS driver 0.10 (2.0.4) Communications with UPS lost: Error executing command Communications with UPS lost: Error executing command Communications with UPS lost: Error executing

Hi, just through setting up nut-2.0.2 I ran into a shutdown problem. As I have already spend some time on it and don't know any further, I like to ask for advice. Situation: Powerware 9125 serially connected using /dev/cua0 nut compiled and installed fine system shall - broadcast a message and shut down if ups on battery for 30+ s - wait 120 s - broadcast another message - give system 120

Hi all, I know there are some howto's about Powerware 5115 and Ubuntu, but I can't still get that thing working. Can someone give some light... 1. Powerware 5115, serial port (ttyS0) 2. Ubuntu 6.06.1 as LTSP-server As reference: http://gentoo-wiki.com/HOWTO_NUT http://keystoneit.wordpress.com/2006/09/25/network-ups-tools-nut-on-ubuntu/ --- a. I try to start driver as root. root at