similar to: Kernel panic - em0 culprit?

Hello, I have a server pfsense in bridge mode to function as transparent FW, the problem is that once I connect the pfsense between my router core and my core switch catalyst a few seconds begin to appear several messages like these: em2: watchdog timeout - resetting em2: watchdog timeout - resetting em2: watchdog timeout - resetting em2: watchdog timeout - resetting And the connection falls

I have a current RELENG_7 running on: http://www.supermicro.com/products/system/4U/7045/SYS-7045B-TR+.cfm with the -3+ IPMI card. I can interact with the BIOS, etc, but no joy once we get past the loader. Anyone have ideas? Attached is the kernel config, and the /var/run/dmesg.boot file. -- Larry Rosenman http://www.lerctr.org/~ler Phone: +1 512-248-2683

Hi, I had 6 crash in 3 hours with exactly the same messages is my aac controler dead ? aac0: COMMAND 0xc4c9d900 TIMEOUT AFTER 512 SECONDS aac0: WARNING! Controller is no longer running! code= 0x100 Fatal trap 12: page fault while in kernel mode cpuid = 0; apic id = 01 fault virtual address = 0x5a fault code = supervisor read, page not present instruction pointer =

Hi, I have Orinoco 802.11b PC Card from Proxim. I plugged it to pcmcia slot, but It doesn't work - no blinking LEDs, no wi0 in ifconfig. I have 7.1-PRERELEASE, laptop Prestigio Nobile 157. On NetBSD seems working, but NetBSD is not friendly with me. if_wi driver included in kernel. ----- dmesg Copyright (c) 1992-2008 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989,

Hi, I currently encounter spin lock 0xc0c83ba8 (sio) held by 0xc6337460 (tid 100005) too long panic: spin lock held too long cpuid=3 on hp server with two dual-core intel xeon (3.8GHz) and 3GB RAM. System is 7.1-PRELEASE last fetched 29.11.2008, 17:58 UTC. This happens with VSCom Card that was previously in use in a 5.3-STABLE system (also hp server, but older hardware) without problems. The

Hello, I am attempting to get by broadcom wifi card up and running, am sick of trying to get ndis working, and am attempting to use the bwi driver (originating in dragonflyBSD). I'm hoping others here have tried to do the same and have some pointers. I'm using 7.1-RELEASE (system/source are in-sync) and my card is a BCM94306MP. My dmesg is posted below. Bwi(4) is installed and it

I have an Asus A8V-MX motherboard with an AMD Athlong 64 X2 3800+ CPU and I'm trying to run powerd to keep it cooler/quieter/greener. I'm running -STABLE (6.1-RC) cvsup'ed a couple of days ago, with a kernel config that consists of the SMP sample plus an atapicam device. I'm loading the cpufreq.ko module in /boot/loader.conf. I've attached my dmesg output and sysctl -a

Hello, I am trying to use a 1.5TB Eonstor raid array with FreeBSD 7.0, but I don't understand whether it is the raid or the scsi card or something else that is causing the computer problems when accessing the raid. My problem is that soon after recognizing the attached disk during boot, FreeBSD appears to hang for about 10 seconds and then says ahd0: Recovery Initiated - Card

Good morning, I'm having a bit of an issue getting a 3CR990B-TXM NIC detected and usable. Just wondering if anyone knows of any issues with this NIC chipset and/or with the motherboard chipset. The motherboard is a Biostar GeForce 6100 AM2 using an nVidia nForce 410 chipset and nVidia GeForce 6100 vide chipset. I've tried FreeBSD 6.1, 6.2, 6-STABLE (from Wed), and 7-CURRENT (from

I have a new system which includes a Plextor PX-740a DVD+-R/RW CD-R/RW drive attached to an Asus A8V-MX motherboard. When I try to use burncd to burn a cd, it writes all of the data, says "fixating CD, please wait.." and then reports burncd: ioctl(CDRIOCFIXATE): Input/output error Oddly enough, the CD seems to be usable. I can successfully burn the same file if I use cdrecord. The

Hello Got strange problem with high system "%system load" and very slow user level programs (apache+php+mysql) behavior gstat shows 1.5-4% hard disk busy load but system shows about 20-30% load while user load is max 5%. vmstat shows from 2 to 35 process in "b" state. Now use 7.0-RELEASE-p5 , but the same problem was with 7.0-RELEASE. And have no idea what to do with this.

Hello all. I have a supermicro 16 bay box with a LSI 9211-8i card. We use it for temp data storage, and we wanted to try the l4z compression. After updating the source tree to r247839: and doing a make buildworld cycle all works fine. But at boot time we get some warnings. make_dev_physpath_alias: WARNING - Unable to alias gptid/281951f4-a996-11e1-83eb-00259061b51a to enc at

I'm running FreeBSD 7.1-PRERELEASE over Asus P5Q motherboard. Such board comes with an nic requiring age0 driver. When the nic is under load, such trasferring big amount of data over gigabit connection (let's say some gigabyte backups), the computer hangs, sometimes with panic, sometimes freezing. Before that i was using an Intel nic with em0 driver and 7.0-Stable#2.. and that

Can anyone help me here? ----- Forwarded message from Larry Rosenman <ler at lerctr.org> ----- Date: Sat, 9 Nov 2013 08:46:26 -0600 From: Larry Rosenman <ler at lerctr.org> To: freebsd-stable at freebsd.org Subject: 10-BETA3: Bad negotiation on AHD controller User-Agent: Mutt/1.5.22 (2013-10-16) Ever since I put 10 on this box (source upgrade from 8), I've been getting slow

These are new boxes. http://www.supermicro.com/products/system/1U/5015/SYS-5015B-MT.cfm core 2 Q6600 CPU 8Gb 667 RAM Boxes were memtested from Fri-Mon okay. 6.3-RELEASE (amd64) installs fine. Build cycle okay. Running (no load) for a week or so. However, when I try to configure gmirror they hang on boot. After some fiddling it appears issuing #kldload geom_mirror hangs the boxes very hard.

Hello everybody, we recently got three Dell PowerEdge servers equipped with Qlogic QLE2462 cards (dual FC 4Gbps ports) and an EMC CLARiiON CX3-40 SAN. The servers with the FC cards were successfully and extensively tested with an older SUN StorEdge T3 SAN. However, when we connect them to the CX3-40, create and mount a new partition and then do something as simple as "tar -C /san -xf

I recently put together a new machine w/ a SuperMicro H8SCM and an AMD Opteron 4228 HE... I've having an issue where the clock on the machine skips around... The wierd part is that it's very sudden when it happens... ntp sometimes brings it back, but it can't when the clock gets too far ahread (1000 seconds), ntp dies... In order to catch it happening, I ran a sleep 60 loop

This morning, I upgraded my main system to an up-to-date -STABLE including acpi and it now hangs during shutdown after reporting: Waiting (max 60 seconds) for system process `vnlru' to stop...stopped If I set hw.acpi.disable_on_poweroff=0 then the shutdown completes but poweroff fails with (hand copied): ACPI-1287: ***Error: Method execution failed [\_PTS] (Node 0xc21ed450),

Hi, We're having some trouble with detection of a couple of Sil3124 SATA controller cards on newer motherboard and processor combos. Specifically, we're running a Supermicro X9SCM-F motherboard (latest BIOS) and Intel E3-1220v2 CPU. What we're seeing: - Syba Sil3124 PCIe cards are only being detected when installed in PCIe Slot 4 -- The motherboard documentation shows that this

Hi, I've installed 7.2-PRERELEASE, csup on 20090423 at around 19:00 UTC. When I rebooted after installing world, X started (xdm in /etc/ttys) and immediately panicked the system, even before switching to the new VTY. I removed all ports and installed Xorg from today's ports HEAD, same result. This is the case with my old xorg.conf and a new one from 'Xorg -configure'. I