On 1/12/09, Neal Hogan <nealhogan@gmail.com>
wrote:> Hello,
>
> I am attempting to get by broadcom wifi card up and running, am sick of
> trying to get ndis working, and am attempting to use the bwi driver
> (originating in dragonflyBSD). I'm hoping others here have tried to do
the
> same and have some pointers. I'm using 7.1-RELEASE (system/source are
> in-sync) and my card is a BCM94306MP. My dmesg is posted below.
>
> Bwi(4) is installed and it recognizes my card
(*if_bwi_load-"YES"* is in my
> /etc/rc.conf and *bwi_v3* and *if_bwi* are loaded). I can send a IP request
> to my WEP encrypted access point. Yet, it doesn't get an offer and says
that
> *no DS tssi* and *no OFDM tssi* Being new to bwi(4) and have never seen
> references to DS/OFDM tssi, I'm not sure what info to provide. My
research
> is not leading anywhere helpful. Thanks.
>
>
>
>
> Copyright (c) 1992-2009 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 7.1-RELEASE #0: Sat Jan 10 19:07:15 CST 2009
> nph@frege.lambdaserver:/usr/obj/usr/src/sys/GENERIC
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: mobile AMD Athlon(tm) XP2400+ (1788.94-MHz 686-class CPU)
> Origin = "AuthenticAMD" Id = 0x6a0 Stepping = 0
>
>
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
> AMD Features=0xc0480800<SYSCALL,MP,MMX+,3DNow!+,3DNow!>
> real memory = 468647936 (446 MB)
> avail memory = 444530688 (423 MB)
> kbd1 at kbdmux0
> ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
> acpi0: <PTLTD RSDT> on motherboard
> acpi0: [ITHREAD]
> acpi0: Power Button (fixed)
> Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
> acpi_timer0: <32-bit timer at 3.579545MHz> port 0x8008-0x800b on
acpi0
> acpi_ec0: <Embedded Controller: GPE 0x18> port 0x62,0x66 on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci_link5: BIOS IRQ 10 for 0.10.INTA is invalid
> pci0: <ACPI PCI bus> on pcib0
> agp0: <ATI RS100 AGP bridge> on hostb0
> pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> vgapci0: <VGA-compatible display> port 0x9000-0x90ff mem
> 0xe0000000-0xefffffff,0xd0100000-0xd010ffff irq 10 at device 5.0 on
> pci1
> ohci0: <AcerLabs M5237 (Aladdin-V) USB controller> mem
> 0xd0006000-0xd0006fff irq 9 at device 2.0 on pci0
> ohci0: [GIANT-LOCKED]
> ohci0: [ITHREAD]
> usb0: OHCI version 1.0, legacy support
> usb0: SMM does not respond, resetting
> usb0: <AcerLabs M5237 (Aladdin-V) USB controller> on ohci0
> usb0: USB revision 1.0
> uhub0: <AcerLabs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on
usb0
> uhub0: 4 ports with 4 removable, self powered
> pcm0: <Acer Labs M5451> port 0x8400-0x84ff mem 0xd0007000-0xd0007fff
> irq 5 at device 6.0 on pci0
> pcm0: <Conexant CX20468 AC97 Codec>
> pcm0: [GIANT-LOCKED]
> pcm0: [ITHREAD]
> isab0: <PCI-ISA bridge> at device 7.0 on pci0
> isa0: <ISA bus> on isab0
> pci0: <simple comms, generic modem> at device 8.0 (no driver
attached)
> bwi0: <Broadcom BCM4306v1 802.11 Wireless Lan> mem
> 0xd0004000-0xd0005fff irq 9 at device 9.0 on pci0
> bwi0: [ITHREAD]
> bwi0: regwin: chipcommon (0x800), rev 2, vendor 0x4243
> bwi0: BBP: id 0x4306, rev 0x2, pkg 0
> bwi0: nregwin 6, cap 0x0000002a
> bwi0: regwin: 802.11 MAC (0x812), rev 4, vendor 0x4243
> bwi0: has TX stats
> bwi0: MAC: rev 4
> bwi0: regwin: pcmcia (0x80d), rev 1, vendor 0x4243
> bwi0: regwin: v90 codec (0x807), rev 1, vendor 0x4243
> bwi0: regwin: pci (0x804), rev 7, vendor 0x4243
> bwi0: regwin: 802.11 MAC (0x812), rev 4, vendor 0x4243
> bwi0: ignore second MAC
> bwi0: bus rev 0
> bwi0: pci is enabled
> bwi0: card flags 0x000f
> bwi0: 0th led, act 3, lowact 0
> bwi0: 1th led, act 5, lowact 0
> bwi0: 2th led, act 4, lowact 0
> bwi0: 3th led, act 0, lowact 0
> bwi0: 802.11 MAC was already disabled
> bwi0: PHY is linked
> bwi0: PHY: type 2, rev 1, ver 1
> bwi0: PHY: 802.11G attach
> bwi0: RF: manu 0x17f, type 0x2050, rev 2
> bwi0: bus rev 0
> bwi0: PHY is linked
> bwi0: 30bit bus space
> bwi0: max txpower from sprom: 57 dBm
> bwi0: invalid antenna gain in sprom
> bwi0: ant gain 8 dBm
> bwi0: region/domain max txpower 76 dBm
> bwi0: max txpower 57 dBm
> bwi0: sprom idle tssi: 0x003e
> bwi0: TSSI-TX power map:
> 71 71 70 70 70 70 70 69
> 69 69 69 69 68 68 68 67
> 67 67 66 66 66 66 65 65
> 65 64 64 64 63 63 63 62
> 61 61 61 60 59 59 58 57
> 57 55 55 54 53 52 51 50
> 49 48 47 44 43 42 39 37
> 35 32 29 26 22 18 14 8
> bwi0: idle tssi0: 62
> bwi0: bus rev 0
> bwi0: locale: 6
> bwi0: WARNING: using obsoleted if_watchdog interface
> bwi0: Ethernet address: 00:90:4b:61:02:45
> cbb0: <O2Micro OZ6912/6972 PCI-CardBus Bridge> irq 11 at device 10.0
on pci0
> cardbus0: <CardBus bus> on cbb0
> pccard0: <16-bit PCCard bus> on cbb0
> cbb0: [ITHREAD]
> fwohci0: <Texas Instruments TSB43AB21/A/AI/A-EP> mem
> 0xd0009000-0xd00097ff,0xd0000000-0xd0003fff irq 10 at device 12.0 on
> pci0
> fwohci0: [FILTER]
> fwohci0: OHCI version 1.10 (ROM=1)
> fwohci0: No. of Isochronous channels is 4.
> fwohci0: EUI64 00:0d:9d:71:9e:43:0c:6a
> fwohci0: Phy 1394a available S400, 1 ports.
> fwohci0: Link S400, max_rec 2048 bytes.
> firewire0: <IEEE1394(FireWire) bus> on fwohci0
> fwe0: <Ethernet over FireWire> on firewire0
> if_fwe0: Fake Ethernet address: 02:0d:9d:43:0c:6a
> fwe0: Ethernet address: 02:0d:9d:43:0c:6a
> fwip0: <IP over FireWire> on firewire0
> fwip0: Firewire address: 00:0d:9d:71:9e:43:0c:6a @ 0xfffe00000000,
> S400, maxrec 2048
> sbp0: <SBP-2/SCSI over FireWire> on firewire0
> dcons_crom0: <dcons configuration ROM> on firewire0
> dcons_crom0: bus_addr 0x12bc000
> fwohci0: Initiate bus reset
> fwohci0: BUS reset
> fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
> atapci0: <AcerLabs M5229 UDMA100 controller> port
> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x8080-0x808f at device 16.0 on
> pci0
> atapci0: using PIO transfers above 137GB as workaround for 48bit DMA
> access bug, expect reduced performance
> ata0: <ATA channel 0> on atapci0
> ata0: [ITHREAD]
> ata1: <ATA channel 1> on atapci0
> ata1: [ITHREAD]
> pci0: <bridge> at device 17.0 (no driver attached)
> sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0x8c00-0x8cff mem
> 0xd000a000-0xd000afff irq 11 at device 18.0 on pci0
> sis0: Silicon Revision: DP83816A
> miibus0: <MII bus> on sis0
> nsphyter0: <DP83815 10/100 media interface> PHY 0 on miibus0
> nsphyter0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> sis0: Ethernet address: 00:0d:9d:43:2b:a7
> sis0: [ITHREAD]
> acpi_button0: <Power Button> on acpi0
> acpi_lid0: <Control Method Lid Switch> on acpi0
> acpi_acad0: <AC Adapter> on acpi0
> battery0: <ACPI Control Method Battery> on acpi0
> acpi_tz0: <Thermal Zone> on acpi0
> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> atkbd0: [ITHREAD]
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: [GIANT-LOCKED]
> psm0: [ITHREAD]
> psm0: model IntelliMouse, device ID 3
> fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
acpi0
> fdc0: [FILTER]
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10
on
> acpi0
> sio0: type 16550A
> sio0: [FILTER]
> cpu0: <ACPI CPU> on acpi0
> powernow0: <PowerNow! K7> on cpu0
> pmtimer0 on isa0
> orm0: <ISA Option ROMs> at iomem
> 0xc0000-0xcefff,0xcf000-0xcf7ff,0xdb000-0xdbfff,0xdc000-0xdffff pnpid
> ORM0000 on isa0
> ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 16/16/16 bytes threshold
> ppbus0: <Parallel port bus> on ppc0
> ppbus0: [ITHREAD]
> ppi0: <Parallel I/O> on ppbus0
> plip0: <PLIP network interface> on ppbus0
> plip0: WARNING: using obsoleted IFF_NEEDSGIANT flag
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppc0: [GIANT-LOCKED]
> ppc0: [ITHREAD]
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
> ums0: <Logitech USB Receiver, class 0/0, rev 1.10/25.00, addr 2> on
uhub0
> ums0: 16 buttons and Z dir.
> Timecounter "TSC" frequency 1788943467 Hz quality 800
> Timecounters tick every 1.000 msec
> firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
> firewire0: bus manager 0 (me)
> ad0: 95396MB <Seagate ST9100823A 3.02> at ata0-master UDMA100
> acd0: CDRW <QSI CD-RW/DVD-ROM SBW-241/VH04> at ata1-master UDMA33
> Trying to mount root from ufs:/dev/ad0s2a
> bwi0: bwi_init
> bwi0: bwi_stop
> bwi0: bbp atten: 0, rf atten: 3, ctrl1: 2, ctrl2: 65535
> bwi0: bus rev 0
> bwi0: 802.11 MAC is disabled
> bwi0: 802.11 MAC was already disabled
> bwi0: PHY is linked
> bwi0: bus rev 0
> bwi0: PHY is unlinked
> bwi0: RF calibration value: 0x002a
> bwi0: bus rev 0
> bwi0: PHY is linked
> firmware_get: failed to load firmware image bwi_v3_ucode4
> bwi0: request firmware bwi_v3_ucode4 failed
Looks like it either doesnt have such firmware loaded or firmware
is not supported for your card. bwi works only with firmware version 3
and not with 4.
To get right answer look in current openbsd and dragonfly bwi driver if
your BCM94306MP is listed.
--
Paul