similar to: Asterisk Release 20.4.0

The Asterisk Development Team would like to announce the release of Asterisk 18.19.0. The release artifacts are available for immediate download at https://github.com/asterisk/asterisk/releases/tag/18.19.0 and https://downloads.asterisk.org/pub/telephony/asterisk This release resolves issues reported by the community and would have not been possible without your participation. Thank You!

The Asterisk Development Team would like to announce the release of Asterisk 18.19.0. The release artifacts are available for immediate download at https://github.com/asterisk/asterisk/releases/tag/18.19.0 and https://downloads.asterisk.org/pub/telephony/asterisk This release resolves issues reported by the community and would have not been possible without your participation. Thank You!

The Asterisk Development Team would like to announce security release Certified Asterisk 18.9-cert5. The release artifacts are available for immediate download at https://github.com/asterisk/asterisk/releases/tag/certified-18.9-cert5 and https://downloads.asterisk.org/pub/telephony/certified-asterisk The following security advisories were resolved in this release:

The Asterisk Development Team would like to announce security release Certified Asterisk 18.9-cert5. The release artifacts are available for immediate download at https://github.com/asterisk/asterisk/releases/tag/certified-18.9-cert5 and https://downloads.asterisk.org/pub/telephony/certified-asterisk The following security advisories were resolved in this release:

The Asterisk Development Team would like to announce the release of asterisk-21.0.0. The release artifacts are available for immediate download at https://github.com/asterisk/asterisk/releases/tag/21.0.0 and https://downloads.asterisk.org/pub/telephony/asterisk This release resolves issues reported by the community and would have not been possible without your participation. Thank You!

The Asterisk Development Team would like to announce the release of asterisk-21.0.0. The release artifacts are available for immediate download at https://github.com/asterisk/asterisk/releases/tag/21.0.0 and https://downloads.asterisk.org/pub/telephony/asterisk This release resolves issues reported by the community and would have not been possible without your participation. Thank You!

The Asterisk Development Team would like to announce the release of asterisk-20.5.0. The release artifacts are available for immediate download at https://github.com/asterisk/asterisk/releases/tag/20.5.0 and https://downloads.asterisk.org/pub/telephony/asterisk This release resolves issues reported by the community and would have not been possible without your participation. Thank You!

The Asterisk Development Team would like to announce the release of asterisk-20.5.0. The release artifacts are available for immediate download at https://github.com/asterisk/asterisk/releases/tag/20.5.0 and https://downloads.asterisk.org/pub/telephony/asterisk This release resolves issues reported by the community and would have not been possible without your participation. Thank You!

Hello, On a Debian Buster instance, I compiled Asterisk 17.3.0 from source. I enables all 3 File, IMAP and ODBC voicemail modules but I'm still using classical File module (in modules;conf and voicemail.conf): cd asterisk-17.3.0 ... make menuselect.makeopts menuselect/menuselect --enable app_voicemail_imap menuselect.makeopts; done menuselect/menuselect --enable app_voicemail_odbc

Hi, Continuing with the saga of Digium vs MTNL Mumbai, looking for suggestions on handling incoming Caller-ID issues. The card manages to grab a couple of (random) digits of the incoming CID, but they're more or less useless. Is there any way to fix this? Asterisk 1.8.13, Dahdi 2.5.0.1 on Debian Testing (Wheezy), MTNL Mumbai. Digium, Inc. Wildcard AEX410 4-port analog card (PCI-Express)

Upgrading an ancient customer installation... was running 1.4.23.1 (Trixbox) with Zaptel 1.4.12.9 and a Sangoma A102D, which has been running fine for 5+ years. Customer getting anxious about hardware failure, so we built a new box and installed 1.8.24.0, Dahdi 2.7.0.1, and a new Sangoma A104D. The single active span is an RBS T1 B8ZS/ESF/E&M Wink. I tried to move one span over one

In Asterisk 1.8, I used the following line in extensions.conf to allow me to pass "*82" in front of a dialed number, to disable the callerid block that's normally on that POTS line: ; disable callerid block exten => _*82.,1,Dial(${POTS}/${EXTEN}) But this seems to have stopped working when I upgraded to Asterisk 11.7. I get the following debug output, with a "no

The Asterisk Development Team would like to announce the release of asterisk-18.20.0. The release artifacts are available for immediate download at https://github.com/asterisk/asterisk/releases/tag/18.20.0 and https://downloads.asterisk.org/pub/telephony/asterisk This release resolves issues reported by the community and would have not been possible without your participation. Thank You!

The Asterisk Development Team would like to announce the release of asterisk-18.20.0. The release artifacts are available for immediate download at https://github.com/asterisk/asterisk/releases/tag/18.20.0 and https://downloads.asterisk.org/pub/telephony/asterisk This release resolves issues reported by the community and would have not been possible without your participation. Thank You!

I'd like to have my Asterisk system pick up a certain extension on an existing Panasonic PBX when it rings. (It's connected to some proprietary Panasonic doorphones that I haven't replaced yet.) I connected that extension to an FXO port on a Digium AEX410 card, and set that channel to have the context "doorphone". The problem is that the extension is never executed. With

Hi, We've got a dedicated T1 with two trunks running into our ILECs selective router for 911. Split out of the T1 into two MF CAMA trunks on ILEC side. I'm trying to use asterisks e911 signaling, but I'm having trouble with the dial command. (== Everyone is busy/congested at this time (1:1/0/0)) I'm missing something and I'm thinking it has to do with the hookstate

Hi everyone! I have a Digium Card TDM410 But, it appear for me this massege chan_dahdi.c:8061 handle_alarms: Detected alarm on channel 3: Red Alarm But my line is ok! But sometimes it back sig_analog.c:3807 analog_handle_init_event: Alarm cleared on channel 2 But it again back to red alarm. What can be happen? My lines is all ok! But when I put on Digium Card TDM410 is very inconsistent

Humm, if I put a filter in this lines, maybe back? 2016-01-05 12:36 GMT-02:00, Ryan, Travis <RyanT at oscarwinski.com>: > >> -----Original Message----- >> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- >> bounces at lists.digium.com] On Behalf Of Vitor Mazuco >> Sent: Tuesday, January 05, 2016 9:21 AM >> To: Asterisk Users Mailing

System details: Digium Wildcard TDM410P with three extensions and one POTS line. Dual core Pentium 4 (32-bit) processor Fedora 18 Asterisk 11.2.1 DAHDI Version: 2.6.2 Echo Canceller: HWEC I recently upgraded from Asterisk 1.4, and made as few changes to the configuration files as possible. I regenerated the dahdi-channels.conf file, then I believe I had to edit this to set the contexts

The Asterisk Development Team is pleased to announce the release of Asterisk 1.8.9.0. This release is available for immediate download at http://downloads.asterisk.org/pub/telephony/asterisk/ The release of Asterisk 1.8.9.0 resolves several issues reported by the community and would have not been possible without your participation. Thank you! The following is a sample of the issues resolved in