similar to: Assuming write caching from CentOS 4.4 to iSCSI device

Dear Srs, I'm getting this error when trying to connect to a Infortrend A16E- G2130-4 storage v?a iSCSI. > Apr 29 10:24:40 vz-10 kernel: scsi1 : iSCSI Initiator over TCP/IP > Apr 29 10:24:41 vz-10 kernel: Vendor: IFT Model: A16E- > G2130-4 Rev: 361F > Apr 29 10:24:41 vz-10 kernel: Type: Direct- > Access ANSI SCSI revision: 04 > Apr

I've been having an extremely hard time using the on board SATA controller on my nvidia based board. I have two 160gig Maxtor SATA drives attached to the on board controller, setup as software raid0. The problem is the array is extremely unreliable, where I'm getting constant I/O errors like: sd 0:0:0:0: SCSI error: return code = 0x00040000 end_request: I/O error, dev sda, sector

Basically the issue comes down to my Volume Groups not being found by this initrd, causing good ole kernel panic. initrd-2.6.12.6-xen3_12.1_rhel4.1.img [root@xen01 lvm]# uname -a Linux xen01.inside.***.com 2.6.9-22.0.2.ELsmp #1 SMP Thu Jan 5 17:13:01 EST 2006 i686 i686 i386 GNU/Linux [root@xen01 lvm]# cat /etc/redhat-release Red Hat Enterprise Linux ES release 4 (Nahant Update 2) Everything

> > Well, i''m using here the qla2340 on several boxes. It works > > with Xen 2.0 but noch with Xen 3.0. as part of SUSE Linux 10.0: > > Interesting. If the driver really doews work flawlessly in > Xen 2, then I think the culprit has to be interrupt routeing. > > Under Xen 3, does /proc/interrupts show you''re receiving interrupts? I cannot boot with

> > Well, i''m using here the qla2340 on several boxes. It works > > with Xen 2.0 but noch with Xen 3.0. as part of SUSE Linux 10.0: > > Interesting. If the driver really doews work flawlessly in > Xen 2, then I think the culprit has to be interrupt routeing. > > Under Xen 3, does /proc/interrupts show you''re receiving interrupts? I cannot boot with

Hi folks, Backing up a host as noted below im getting over and over again the same issue on actual kernel, details: - Backup host has a pci/usb2.0 card, with a 250gb usb 2.0 disk attached, - Celeron 900 family - Remote host, local console from boot linux rescue: # dd if=/dev/hda conv=sync,noerror | ssh -c blowfish root at 192.168.0.6 "dd of=/media/backup/vol-hda.raw.img" - Backup

Hello, I have a weird problem after adding new PV do LMV volume group. It seems the error comes out only during boot time. Please read the story. I have couple of 1U machines. They all have two, four or more Fujitsu-Siemens SAS 2,5" disks, which are bounded in Raid1 pairs with Linux mdadm. First pair of disks has always two arrays (md0, md1). Small md0 is used for booting and the rest - md1

I just tried this with CentOS 5.3 as well, and got exactly the same symptoms and dmesg output. (As a point of comparison, Ubunu 8.04 on my work laptop is able to access the drive.) Obviously "not detected" is a misapprehension, though I'm puzzled why "lsusb" doesn't show it. The device is there even though the partition table can't be read. ---------- Forwarded

We have a 3TB external USB drive that I am trying to attach to some CentOS5 servers. I have tried an older Dell PE1950 and a newer R310 but neither one seems to be able to read the drive. It works no problem on windows servers/workstations and I was able to format with NTFS. I know there are different methods for formatting large disks but this one doesn't even seem to show up as a /dev/

Hello, We have recently purchased two Supermicro servers, AS-1021M-T2RB (http://www.supermicro.com/Aplus/system/1U/1021/AS-1021M-T2RV.cfm), and have built them both with CentOS 5 operating system. They are identical, apart from the manufacturer of the disk drives. Kernel is: Linux version 2.6.18-8.1.6.el5 (mockbuild at builder6.centos.org) (gcc version 4.1.1 20070105 (Red Hat 4.1.1-52)) #1 SMP

Hello List, I'm hoping someone else out there has an Asus DSBF-DE server board, and can tell me if anything special needs to be done to get ports 5 and 6 of the onboard SATA to work under Centos 5.1 x64. I have drives on 1 through 4 that are detected and working properly, however, a drive on 5 is not detected, from what i can tell, the kernel doesn't even see phy's for ports 5 and 6.

I really hope someone has a clue on this one.... :) I've got a 2.2TB array mounted on a 3ware 9500 controller. I installed it last week ensuring that LBA was enabled and using gpt with parted to get the full size available on one array. I also think I chose reiserfs for the array. We then moved ALOT of data to the array. Problem now is that after a reboot LBA doesn't seem to be in

I have just bought a 120GB external usb drive but after plugging it in it is not getting mounted. lines from /var/log/messages: > Oct 22 18:54:49 station2 kernel: usb 1-2: new high speed USB device using ehci_hcd and address 2 > Oct 22 18:54:49 station2 kernel: usb 1-2: configuration #1 chosen from 1 choice > Oct 22 18:54:49 station2 kernel: scsi4 : SCSI emulation for USB Mass Storage

Hello, A message was already posted here regarding this issue- I experience the same problem with 6 machines, all with Hitachi harddrive, VIA Motherboard which uses the sata_via driver: Once every few days each machine freezes or just stops reading from the HD and throws i/o error messages as pasted below. Note that the first "ata exception Emask" errors apear right after booting,

Hello, I have a Promise EX 12-port RAID controller in my box, connected to 8 750GB disks. I have set up 2 RAID-5 devices and joined these using LVM. This is working fine. However, there is something that seems wrong.. (4-1) * 750 = 2250, but df reports the LVM volume as a mere 4.0T; /dev/mapper/storage_volume-stor 4.0T 3.6T 507G 88% /storage Shouldn't this be 4.5TB? Relevant bit of

I just installed CentOS 5 on a computer. On boot, I get the a error message, related to 2 SATA disks. These errors did NOT appear on version 4.4 with the EXACT same hardware. Could someone please tell me what these error are and if there is some known way to prevent them? My configuration: - 2 Hitachi SATA 120 GB Harddisks - Intel P4 3GHz - Tyan Tomcat i875p motherboard - 1 GB ECC RAM - 2

I just installed CentOS 5 on a computer. On boot, I get the a error message, related to 2 SATA disks. These errors did NOT appear on version 4.4 with the EXACT same hardware. Despite the error messages, the disks seem to be working with no problems. Could someone please tell me what these error are and if there is some known way to prevent them? I searched the Net for these errors and they seem

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 This seems to be an old problem, but I haven't found much about it. SuSE mentions "hwprobe=-pci" but, as far as I know, CentOS doesn't use it. This does stop the machine from booting (mounting /) quite a few times. Logs: SCSI subsystem initialized sym0: <895> rev 0x2 at pci 0000:00:13.0 irq 177 sym0: Symbios NVRAM, ID 7,

Fresh install of CentOS 4.4. uname -a, lspci, & lsusb output at bottom. I insert my 256MB USB key, light goes on, then off. Never mounts. Here's the end of dmesg: usb 1-1: new full speed USB device using address 11 scsi7 : SCSI emulation for USB Mass Storage devices Vendor: Generic Model: STORAGE DEVICE Rev: 1.02 Type: Direct-Access ANSI SCSI revision:

A friend bring and Ipod, initially it didn't start because of charge, so I connected to my PC to give some charge, after that my linux didn't mount it, and when I start the iPod it shows me a folder with a sign, and that's all, nothing else matters. when I connected the iPod to the PC it start to charge and suddenly stops and shows the folder I have talked before I run the command