similar to: Issue with On Line Status (APC MGE Galaxy 5500 + AP9635CH)

I've got an update on this case Using tkmib I discovered that my UPS (NMC per say) sends its state by OID 1.3.6.1.4.1.318.1.1.1.11.1.1.0 .iso.org.dod.internet.private.enterprises.apc.products.hardware.ups.upsState.upsBasicState.upsBasicStateOutputState.0 = 0001010000000000001000000000000000000000000000000000000000000000 (mib used for this snmpget was powernet441.mib) (I got a description about

So what would it take me to edit NUT's code for my case to work? My Network Management Card sends its output state using unfortunately only (I guess so) this OID: 1.3.6.1.4.1.318.1.1.1.11.1.1.0 Weirdly the standard way of obtaining Battery Status (drivers/apc-mib.c) 1.3.6.1.4.1.318.1.1.1.2.1.1.0 gives me good results. Unfortunately power status OID's value type differs (my: 64 digits

One good intro to this is https://github.com/networkupstools/nut/blob/master/docs/snmp-subdrivers.txt although it focuses on adding new subdrivers - but more or less the same workflow applies to extending existing ones. Sometimes it helps to generate a new one for a currently-partially-supported device, and then compare with existing subdriver (using meld or similar GUI helps a lot) to port the

Well thanks, The solution for my problem was kinda easy (still need some testing though): found out my ups status is a string, so then I changed the way snmp-ups.c gets the status. Had to change *nut_snmp_get_int *to *nut_snmp_get_str *at around line 3470, then grab fourth char out, use *strtol *function to then send it to *su_status_set *function. I created my copy of *apc-mib.c *with my OID at

Hello, At my workplace I have exact UPS config as stated in the subject (APC MGE Galaxy 5500 + AP9635CH). I have it set up to work with snmp-ups NUT driver. Despite many readings from *upsc* command I am not receiving "On Line Status" (ups.status OL) nor "On Battery Status" (ups.status OB) and therefore I can't get my systems to shutdown during a power outage event.

mateuszx via Nut-upsdev <nut-upsdev at alioth-lists.debian.net> writes: > At my workplace I have exact UPS config as stated in the subject (APC MGE > Galaxy 5500 + AP9635CH). > I have it set up to work with snmp-ups NUT driver. > Despite many readings from *upsc* command I am not receiving "On Line > Status" (ups.status OL) nor "On Battery Status"

Also, which version of NUT is involved? There were recently PRs (merged to master-branch, eventually will be in 2.8.1) about more SNMP-UPS support including APCs e.g. 1674, 1679, 1113 (should be in 2.8.0)... Many distros still ship 2.7.4... Jim On Tue, Feb 28, 2023, 00:57 Greg Troxel <gdt at lexort.com> wrote: > mateuszx via Nut-upsdev <nut-upsdev at alioth-lists.debian.net>

Citeren Marco Chiappero <marco op absence.it>: > I managed to get twice connected at the same time from the same > machine to a single UPS using different hostnames, so it's > definitely not an IP based check (at least here with 66102 / EC). Never mind. The alarm messages are not bound to a specific outlet, but are sent to all NSM clients that are connected. Which means

Hi all, some time ago I bought at discount price a NMC for managing a few computers using the programmable outlets features available on my MGE Evolution, unuseful otherwise (ATM). However, expecially for my server machine, I don't like very much the NSM client provided by MGE/Eaton and I'd rather use only NUT from my distribution. So, looking at the netxml-ups driver, I started adding

hi @ all, i just wonder, if it is posible to read the values for all the three phases of a mge galaxy 6000 ups? we have unfortunately one mge comet ups (one phase) to play at work, but it is important to know, how many information upsc can deliver from a galaxy. we plane to use web / snmp interface. can someone post the upsc from such ups? thanks in advance, miroslav -- SHALTEV.ORG

Dear folks, According to mge-mib.c (NUT 2.6.2) LB condition is gained from variable .1.3.6.1.4.1.705.1.5.14.0 (i.e. upsmgBatteryLowBattery.0). The test device of me does not set this variable to yes(1) even if runtime drops below the preconfigured limit. I complained about this at Schneider Electric. They replied that low battery status is indicated by .1.3.6.1.4.1.705.1.5.14.0

Dear users, This mail is to announce the beta availability of the mge-xml driver in NUT's trunk. This (overdue) driver allows to support MGE* (UPS Systems and Office Protection Systems) Network Management Cards. This development is sponsored by MGE Office Protection Systems, which is also the NUT sponsor, web hoster and (new) benefactor in general. This driver offers similar services to the

OS: CentOS 7 NUT Version: 2.7 Installed NUT through: yum install nut UPS: APC smart UPS srt3000 with NMC I am trying to set up NUT with snmp for my apc ups. Heres the config; [ups6]                 Driver = snmp-ups                 Port: ups6.domain.name (also tried 192.168.24.9)                 Snmp_version = v3                 secLevel = authPriv                 secName = ups6

Greetings! I am still new to R but have been asked to look at doing astronomy with R. I have a FITS file which contains an optical telescope image (it can be viewed in SAOimageDS9). I need to estimate the magnitude of a galaxy... and eventually other optical sources. How do I find the apparent magnitude of a galaxy from a FITS file? -- View this message in context:

Is there something on the Icecast server I can do to improve compatibility with devices that seem to have a problem with high latency? (at least I think latency is the problem) For example, I have a Samjunk Galaxy tablet that randomly drops the live audio stream. Any other device in my house works fine. I'm streaming an MP3 source live over an HTTPS Internet connection using Icecast

Hi, Has anybody tried to connect Samsung Galaxy to Asterisk PBX to be able to make calls over VoLTE? Thanks a lot in advance! Best regards, Sevana http://www.sevana.biz -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20150403/ac9b4a31/attachment.html>

Has anybody successfully configured asterisk to use Galaxy Voice for inbound / outbound calls and what is required to make this work? Dave --------------------------------------- Dave Tipton dave@lodave.org 817-858-9841 Home 469-223-8506 Cell

Call us on +91-9666 4000 48 - Mobiles <http://www.fosila.com/mobiles> - Cameras <http://www.fosila.com/cameras> - Laptops <http://www.fosila.com/laptops> - Bags <http://www.fosila.com/bags> - Watches <http://www.fosila.com/watches> - Toys <http://www.fosila.com/TeddyBears> Dear *User*, Unbelievable offer Limited stock. Grab it!! Samsung

What software do you use to listen to the stream. Android stock browser? And how are you feeding the audio to icecast? List of files via oggfwd? Am 2020-01-04 00:28, schrieb webmaster at berean-biblechurch.org: > See below, although none of these things should be specific to the Galaxy tablet (my older tablet works fine, too). > > On 2020-01-03 13:20, Robert Jeffares wrote: >

Hi, I have tried Groundwire on IOS , and Android Alcatel (voice and video calls with asterisk 13.3) Also tried Bria on both OS in video and voice. Regards Toufic From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Sevana Oy Sent: Friday, April 03, 2015 12:28 PM To: Asterisk Users Mailing List - Non-Commercial Discussion