similar to: Two gateways

Hy shorewall users :)) I have the following config in my shorewall: DNAT net:200.137.193.2 loc:192.168.0.55 udp 135,445 - 200.137.193.38 DNAT net:200.137.193.2 loc:192.168.0.55 udp 137:139 - 200.137.193.38 DNAT net:200.137.193.2 loc:192.168.0.55 tcp 135,139,445 - 200.137.193.38 The IP

Hi, i need configure traffic shaper limting a traffic to IP.... for sample: In my lan i have 10 user and i need limit to 10 ips = 30k fot each ip/user. Anyone know if can i this?? where i find more information about? tks

Hi, i''m a shorewall users and i have the following problem: I have one class C range of IP''s and i have three zones (net, dmz , loc) I need create one rule to dnat one valid ip address (but not in use in one computer) to one invalid host in my loc zone. How i do? I try this: DNAT net:200.200.200.200 dmz:200.193.137.38 tcp 137,138,139,445 -

Hi, here my system on shorewall: eth0 192.168.108.1 net eth1 192.168.109.1 dmz eth2 192.168.110.1 loc_110 eth3 192.168.111.1 loc I haven''t access from or to server in loc_110 through shorewall. I can use ssh or other types from loc to dmz or from loc to fw, but I can''t use connections to loc_110. I can also use ssh - connection from fw to loc_110 or redirectly. Where is the

Hi, Please suppose following config: Two external interfaces for two different providers On each of them configured NAT for specific IP addr. ie. 4: eth2: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc htb qlen 100 inet 1.1.1.30/30 brd 1.1.1.31 scope global eth2 6: eth4: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc htb qlen 100 inet 2.2.2.66/27 brd 2.2.2.95 scope global eth4 On eth2

Hey all, i am fighting with a strange behavior here - i have two systems connected via a direct crosslink wire. After booting, the connection is up and both systems can reach the other one. After a small time window the interface is down. $ dmesg |grep eth4 igb 0000:41:00.2: added PHC on eth4 igb 0000:41:00.2: eth4: (PCIe:5.0Gb/s:Width x4) igb 0000:41:00.2: eth4: PBA No: G13158-000 8021q:

hi all At last i got sucess !.. but am confused y it didnt work earlier..the difference today was that i reinstalled RH7.2 & complied kernel 2.4.16(not 17).. rest was same..... & the bandwidth too is under control!.. is it normal for to get more than said bandwidth--i mean i restricted a network with 8Kbit(with same script as below) but still was able to get a download(ftp) of

Hello, I have a problem with the following setup, I hope you can help me. I have two internet gateways, one for LAN1 and the second for LAN2. +--------------+ GW1 more eth0| |eth4(SNAT) GW2 ---...routers...-----+ router +----------------- | | +---+------+---+ eth1|

I have a 2.6.12(ubuntu-patchset), kernel recompiled with this routing options: [*] IP: advanced router [*] IP: policy routing [*] IP: equal cost multipath Load balancing is working great, but i have problems whits long term tcp flows (like msn-messenger or vpns or any other type of long term ip based conection). I assume this is because after a period of time, the per-host

Hi, Shorewall version -4.0.12-2 (EL5 rpm version) OS : Centos 5.2 I have shorewall successfully running on Linux with multi ISP. Trying to make services such as "rsync, ftp" go through my secondary ISP. For which I did the following eth0 : Internal LAN eth4 : DSL (Second ISP) => x.x eth5 : T1 (First ISP) => y.y Created the following entries in

I''am using the following script to aggregate the bandwidth of one quad gigabit ethernet controller (pci-express). #!/bin/bash sysctl -w net.ipv4.tcp_reordering = 30 ifconfig eth1 up ifconfig eth2 up ifconfig eth3 up ifconfig eth4 up modprobe sch_teql tc qdisc add dev eth1 root teql0 tc qdisc add dev eth2 root teql0 tc qdisc del dev eth3 root teql0 tc qdisc del dev eth4 root teql0 ip link

Hi, in my lan I have two firewall, fw1 is the first and manage inte-vlan routing. Fw2 manage internet and dmz. fw1 and fw2 have an interface (eth4 for both fw2 and fw1) on the same subnet that permit to the host behind fw1 to reach internet, my problem is on fw2: eth4 is the NIC that connect fw2 and fw1, I would''t like masquerading hosts behind fw1, so to eth4 of fw2 arrive all

Hello, I am attempting a PXE boot between two systems, each with multiple network cards. While there are a total of 8 ports on each computer, only two (each) are connected as follows: Boot Server eth0 - 10GbE fiber channel (private to the set of computers being managed) (Qlogic) eth4 - 1Gb ethernet (public and out of my sphere of management) (NetExtreme II)

Hi, I''m trying to use Shorewall (3.0.6) to accomplish what I thought was going to be fairly simple. Unfortunately, I can''t get the dmz to work correctly, and I''m getting martians logged against the interface at issue. Any help I could get would be greatly appreciated! A picture of my physical setup is attached. I have also attached a shorewall dump. To make a long

Hi all. I have a problem with pciback in OpenSUSE using PVM. I try to send 3 nic for the PVM.. its ok.. but.. if i try ifconfig eth3 up.. got the error... Please.. see this. Anybody.. know this problem? Thanks, Junior opensuse:~ # uptime 3:36pm up 0:03, 2 users, load average: 0.02, 0.06, 0.02 opensuse:~ # uname -a Linux opensuse 2.6.27.7-9-xen #1 SMP 2008-12-04 18:10:04 +0100 x86_64

Hi, This is the first time I write to the list. My english is not so good, but I hope I''ll be understood. I have 4 adsl routers, plugged on a linux box, and this box e used to connect to a local network. The linux box has 5 NICs. eth0: local network inet 10.0.0.56/24 brd 10.0.0.255 scope global eth0 eth1: adsl router 1 inet 192.168.254.1/24 brd 192.168.254.255 scope global

Hello newsgroup, I hope somebody with more routing experience then me can help me with the problem I have. The setup is as described below. A dual internet provider routing, multiple local area networks, and a dmz network with one public and one private ip range. I followed the instructions at lartc.org, and so far everything is working. The default route is via

I am trying to configure a firewall, but nailing down the configuration is eluding me. The box is running Debian stable. Basically, I have a rackmount server with six network cards. eth0 is the internal network, eth1 is a kiosk network, eth2 is a DMZ/wireless network. On the outbound side, eth3 is a DSL connection and eth4 is a cablemodem connection. What I am trying to do is route all internal

Hello guys, I am experiencing a strange behaviour with HTB. Here is my situation: Test PC -------- internet ------------- ISP ----- fiber connection --------- (eht2) RT1 (eth1) --------- wireless connection ------------ (eth4) RT2 (eth0) -------- users RT1 - Slackware router RT2 - Slackware router Delay between Test PC and ISP is approx 450 ms. I have the following shapers

Everyone, Most of the time I am over my head in trying to troubleshoot problems. However, after reading manuals, man pages, and getting advice from this list I have been able to work my way through difficulties, and at the end, I usually have a better understanding of what 'is going on'. I can only hope this method will work on this problem too. I have been chasing a problem with a