similar to: tricky scenario? with shorewall/squid!

Hello all - This is my situation! I have a PC with no PCI slot and no modem! But I would like to install asterisk on it. I want to use SIP based software ONLY with the asterisk PBX system. I already have the asterisk running on a regular PC. BUt when I run assterisk it fails at this point when it parse modules.conf file. [Wait] == Registered application 'Wait' Asterisk Dynamic

I am attempting to create an ipsec tunnel between two CentOS 5.1 systems, network-to-network with two different 192.168.xxx.0/24 LAN segments. I have gone through the documentation on the centos web site, and have the machines to the point where the /var/log/messages show ``IPsec-SA established'' on both machines after runnig ``ifup ipsec0'' (same ipsec0 on each machine). IP

Hi all - I'm making gradual progress implementing asterisk on my box! Now, when I type asterisk it dies at this point. Does anyone have any idea why this is happening! It have checked everything but running out of options! [app_voicemail2.so] => (Comedian Mail (Voicemail System)) == Parsing '/etc/asterisk/voicemail.conf': Found == Registered application 'VoiceMail2'

Hi everyone - I was wondering how do I setup a rule with the following scenario: I have a VPN site-2-site connection setup. Also, on each site I have squid which redirect all local HTTP traffic on 3128. But I have problems when I try to access the other site web server which is 10.50.20.198 from my network setup which is 10.50.30.0/24. I have all other traffic flowing between the two sites

Folks, Ive got two ISP connections that I am using with: --- ip route add 192.168.200.0/24 dev eth2 src 192.168.200.11 table connection1 ip route add default via 192.168.200.1 table connection1 ip route add x.175.244.0/24 dev eth1 src x.175.244.2 table connection2 ip route add default via x.175.244.1 table connection2 ip rule add from 192.168.200.11 table connection1 ip rule add from x.175.244.2

I have a server running Centos4. I found I was seeing some network problems so I tried "route" and found there was no routing. I thought reboot would solve it but it didn't. I had to manually enter a route to the default gateway, there is still no route to the loopback interface. How is this possible? I thought there was default routes built into the kernel, taken from

Dear All, Sorry to trouble again..... After go through www.lartc.org I have implemented the HTB instead of CBQ for the same scenario. Now following files are under /etc/sysconfig/htb directory. eth0 DEFAULT=30 R2Q=10 eth0-2.root RATE=256kbps BURST=25k eth0-2:10.comp1 RATE=120kbps BURST=12k PRIO=0 LEAF=sfq RULE=192.168.200.0/24 eth0-2:20.comp2

Hello, Here is what I want to do: I have a patch that make me able to mark package by its nature useing layer 7. So I use this line to mark a packge (i will use msnmessenger like example): $IPT -t mangle -A POSTROUTING -m layer7 --l7proto msnmessenger -j MARK --set-mark 3001 Now I want that all packges with this mark get throu my gateway using the link at eth2 and all other packges use

Hello Everyone, I am having trouble with booting a soekris 4826 board.after setting up my tftp,dhcp and web servers ,I log into the board using minicom and type boot f0,which doesn't quite work out. > boot f0 NSC DP83815/DP83816 Fast Ethernet UNDI, v1.03 Copyright (C) 2002, 2003 National Semiconductor Corporation All rights reserved. Pre-boot eXecution Environment PXE-2.0 (build 082)

HI All , I am running a FC6 box with two internet links with load balance . Every thing is working fine expect the MSN connection that failed and reconnect every time and SSL connections . I would link to know if with the nona howto I could fix that . I have been tried with no success to redirect that connection only to one link but its look like do not work . Here my configuration :

Hi All, I have some questions on using library rpart. Given my data below, the plotcp gives me increasing 'xerrors' across different cp's with huge xstd (plot attached). What causes the problem or it's not a problem at all? I am thinking 'xerror's should be decreasing when 'cp' gets smaller. Also what the 'xstd' really tells us? If the error bars for

you also need the dev's aswell <p>> >hello! > >While trying to compile the new and final icecast2, I got this compile >error on the make: > >make[3]: *** [xslt.o] Error 1 >make[3]: Leaving directory `/home/boink/icecast-2.0.0/src' >make[2]: *** [all-recursive] Error 1 >make[2]: Leaving directory `/home/boink/icecast-2.0.0/src' >make[1]: ***

Using Samba (2nd edition) discusses using the "interfaces" network configuration option, along with "hosts allow", "hosts deny", etc, to provide support of multiple interfaces. The examples cited only discuss the scenario in which the interfaces are on different subnets. What about the case in which the interfaces of a multi-homed systems are on the same subnet?

Hi! It''s me again bothering you guys, what I want to do is to give full bandwidth to VPN traffic and limit the rest to 30KB/s (kilobytespersecond), ok? Here''s what I have: tcclasses ################################## eth0 1 1kbps 70kbps 1 eth0 2 1kbps 30kbps 2 default eth1 3 15kbps 10000kbps 1 eth1 4

Hi all! I''m trying to shape traffic in a dorm''s network (4 mbit symmetrical internet link, about 200 computers, heavy p2p usage). The router is a p4xeon running linux 2.6.9 with the qnet patches (http://kem.p.lodz.pl/~peter/qnet/). When I activate ip_forward I get >20% packet loss and a lot of duplicates. Any ideas? I attach my shaping script. Thank you very much in advance,

Do you have a source, like Oddcast, to generate the stream & send it over to Icecast for broadcast? >From: Darren <darren@dazdaz.org> >Reply-To: icecast@xiph.org >To: icecast@xiph.org >Subject: [icecast] Ice Cast / win32 basic help >Date: Mon, 22 Dec 2003 16:39:53 +0100 > >Hi, > >I've downloaded and experimented a little with the latest Windows

Hi everybody I want to specify the contrasts to build a cell means model on LME (each coefficient is the mean value of the independent variable for the specific category of a factor variable) when there are several factors as fixed effect in the model and also interactions between them. Can anybody give me a hint on how to do accomplish this? Also, how can I override the default

Hi, I'm new to libvirt so please bear with me. I am trying to set up a routed subnet on my laptop with libvirt, hoping it to be able to communicate with all servers in my nw. My laptop is on a subnet, 192.168.2.0/24, with a static ip, 192.168.2.27. I have "more or less" followed this guide for routed networks,