similar to: directing output of tftpd to stdout, instead of syslog()

OK here's our setup, we're running pfSense as our firewall/router. We have a dual-WAN with a Comcast Business Gateway and another local ISP. We're running Samba 4.7.6 as the AD DC & Bind 9.9.4. Here's the issue, we just upgraded our Comcast service to a higher speed & they replaced the modem/gateway. Everything was working fine, before the modem swap. Once they did

On 12/04/2020 02:08, Barry Ralphs via samba wrote: > OK here's our setup, we're running pfSense as our firewall/router. We > have a dual-WAN with a Comcast Business Gateway and another local ISP. > We're running Samba 4.7.6 as the AD DC & Bind 9.9.4. Here's the issue, > we just upgraded our Comcast service to a higher speed & they replaced > the

We recently upgraded Samba on our DC from 4.7.6-0 to 4.11.9-3. Everything seems to be running fine over the last few weeks after the update. I'm now setting up a new computer & am having issues getting it to register with DNS. Windows shows that it has joined the domain. I can see the system in ADUC, but no A record in DNS Manager. I've run ipconfig /registerdns, but the event log

> Are you sure it worked before ? > > This is my take on your named.conf: > > ??? acl mynetworks { > ??????? 192.168.254.0/24; > ??????? 192.168.252.0/24; > ??????? 192.168.251.0/24; > ??????? 192.168.250.0/24; > ???? }; > > ??? options { > ??????? directory???? "/var/named"; > ??????? notify no; > ??????? empty-zones-enable no; > ???????

Has anybody tried to to compile SAMBA using gcc under SCO unix 5? This may just be a problem I'm having using the gcc compiler, but I'm having problems. I would just like to know if anyone's done it, and any special problems they may have had. ______________________________________________________ Get Your Private, Free Email at http://www.hotmail.com

Is there some reason why > (1:2)+(1:3) [1] 2 4 4 Warning message: In (1:2) + (1:3) : longer object length is not a multiple of shorter object length can't be made into an error? I realise it was there in S-PLUS, but since it produces a warning there can't be many examples on CRAN or Bioconductor using it, and I can't think of any situation where it would be used deliberately.

I have sources for samba 1.9.18p8. I'm trying to build the package on HPUX 10.20 I beleive it cann't seem to find the varargs macros. What linker options / enviroment variables do I need to turn on? I'm a little new to HPUX. Thanks for your help. HERE's my output from make....... Using CFLAGS = -O -DSYSLOG -DSMBLOGFILE="/opt/utils/samba/var/log.smb"

PArdon the "newbie" nature of this question, but I *am* a samba newbie I'm trying to compile samba-1.9.18p6 on a DEC Alpha running OSF/1 V3.0 (I know it's old, but I'm stuck with it). I've modified the Makefile as follows... ># Add any optimisation or debugging flags here ># add -DSYSLOG for syslog support >FLAGS1 = -O -std1 -w >LIBS1 = and ># This

to> A short time ago I recieved a reply to a query to> about compiling samba with the freeware gcc under to> sco unix. Im sorry, Ive misplaced your Email to> address and WEB address (which was in italian). to> Sorry to use this forum as a contact point, but to> can you contact me again? Thanks. to> to> Tony Nichols The WEB page is at

remove

> Sorry, but in the first mail I forgot to attach the Makefile and I > forgot also to mention that I already tried the password handling in win95 > via the registry. > > De Boe Bart wrote: > > > Hello, > > > > I need to install Samba on a HP J210 HPUX 10.20. > > I downloaded and compiled version 1.9.18p10. > > > > Following problems are

Hi, Let me explain what I'm looking for a solution using asterisk. I have one third party SIP based server (A) and on Asterisk server (B). 1. Extension-1 --> Server A calls Server B. 2. Server B does some processing and calls/sends back to Server A ---> Extension-2 3. SIP session has been established b/w two Extension-1 and Extension-2. Now is there any config that I can do in

[sorry if re-post - first mail to the list and did not get confirmation for earlier mail] Dear all. Not sure what's the best way to describe the scenario and having searched all over the place without luck, I hope some of you may have the correct answer to this scenario: I have an incoming PRI connection to Asterisk 1.4.2. In the office we have two SIP phones and one Zap analog

OK, Asterisk Newbie I've read TFOT and the Asterisk handbook and lurked, but my skills are a bit poor so perhaps someone could post a dialplan fragment to help me Brief details Asterisk@home 2.6 installed on a miniITX system Digium 400 card with 3 FXO modules 3FXS interfaces by Iaxy (1FXS) and Linksys PAP2 (Sipura 2002) (2FXS) I started with AMP to get going but have started

I have a server that I have to reach from 2 different networks, the Internet and another private network called downtown and I also have to reach from the server both networks. If I have one of the set of rules running, it works fine, but if I put both set of rules on, it doesn't work. below are my set of rules. Can anyone tell me a how this can be done? Here is the setup. mynetwork

This may be more a question about the pseudo-DOS command line than about flac itself, but at this point I don't really know. How can one direct the output of flac -t to a file instead of the screen? Often I'd like to verify a large number of flac files, and Speek's front-end is very good for writing up the batch file for that (flac -t itself doesn't seem to expand wildcards on

According to ?system2, I should be able to direct the output of STDERR to a file by giving the filename as a character vector to the "stderr" argument. But here is what happens. Given a ruby script test.rb (with its executable bit set): #!/usr/bin/env ruby STDOUT.puts "stdout" STDERR.puts "stderr" And the following R code: > t <- tempfile() > res <-

Hi all - I'm a first-timer on this list. Just downloaded and installed the latest version (20041019) - works very well - very many thanks to the devs! When I'm running an app using Wine, I get a few warnings and error messages. I'd like to be able to redirect these to a file (for two reasons) a) I'd rather they went to a file instead of the screen ( if I know an app

I am starting to play with validations as I want to catch errors before SQL rejects inserts to the table which are ugly when nulls are sent to ''Not Null'' columns, etc. If I do something in my model like... validates_format_of :first_name, :with => /^\w+$/, :message => "you moron, enter a name" I still end up

How do I use... <%= link_to "All Facilities", :action => ''fac_log_all'' %> if I add :target => "_new" that is just a parameter and not a directive. I just want reports to print into a separate window. How do I do that? It''s not clear at all to me Craig