similar to: SAMBA DNS interfaces set to br0

Am 24.02.19 um 16:51 schrieb Brian Davis via samba: > On a machine with virtual networking is enabled and two ether net > controllers eth0/192.168.1.2 and eth1/192.168.1.3 and having SAMBA smb.conf > set to: > > dns interfaces = lo br0 > > is there a chance for: > > 1) The system not to boot with DNS working > 2) The DNS server bounce between eth0 and eth1 > 3)

Hi, How can i count the number of packets on an interface evry 2 or 5 seconds. and i want to count only specific packets like only arriving packets from port 5001 Any thoughts... Muhammad

I know this is on the wiki, I just want to confirm so I don't blow up my cisco phones. I've got several cisco 7940's all running using cisco power cubes. However, my boss wants me to switch just a few over to poe, but doesn't want to fork out the dough for a nice cisco poe switch, or anybody else's poe switch for that matter. So my question is, what is the '99.999%

I need to connect up to sixteen phones per building, I can use a cheap hub, but POE would be useful. Is there a cheap POE hub available? Everything I have seen has been expensive. Chris Mason

Hi all, I'm looking for recommendations on ethernet switches for a new install. Ideally would want switches with at least 24 ports, ideally with a GE uplink, and that support PoE (power over ethernet) on every port. I've seen lots of switches, and lots of "power hubs", but the combination, which makes a lot of sense, seems rare. What is out there? Do the switches need to be

Hey guys, I was wondering what POE solutions are being used ? Ive done some searching on google and found that PowerDsine seems to be good brand. Any comments,suggestions, and experiences on POE hubs other POE products would be greatly appreciated. Thank you, Steve Maroney

Based on several threads I've read on this list, I assume that it would be handy to supply POE (power over ethernet) in an environment without having to purchase POE switches (assumed expensive) and abandon one's existing (familiar/custom/not-yet-expensed/etc.) switches/hubs. Assume I have a non-POE switch with 24 RJ-45 (ethernet) ports. I design a 1U box that can be mounted just

Hi, Do you need a special cable and power for that unit or you can run it of PoE Switch? Thanks. robert

Dear R users, I have some trouble with the aggregate function. Here are my data > daf S_id AF_Class count... R_gc_percent S_length 5 8264497 1 30 0.48 35678 6 8264497 3 7 0.48 35678 8 8264554 1 31 0.51 38894 9 8264554 2 11 0.51 38894 10 8264554 3 1 0.51 38894

I have a 501 with traditional power and a 301 with PoE. I rightfully assumed that the traditional power from the 501 would work on the 301. How do I get the PoE to work? Do I use the Polycom PoE cable in addition to whatever PoE injection method I use? I have a Cisco PoE injector that works on my Cisco AP350 and my 7960. No combination of this injector, the Polycom cable, and the phone result in

I'm trying to spec out hardware for a new office, and I'd like to include power over Ethernet as an option. I've seen a handful of PoE injectors around $1000 for 24 ports and a couple switches up around $2500 for 24 ports. Are there any cheaper options, short of buying a boatload of 1-port injectors off of ebay? I don't really need more then 24 ports of PoE out of 48 total

Hey, all. We're rolling out VoIP, and I'm wondering about PoE recommendations, as we're going to have to replace our current network equipment. My first inclination would be to just plunk down the cash and do a Cisco system, but I'm relatively certain that would get shot down by finance. Any recommendations for a couple-hundred-port solution with VLANs, PoE, and QoS? Don't

Hello All, I apologize for the slightly off-topic question, but I'm sure that the people best acquainted with the issue would be hanging around here. We recently deployed several Linksys POE switches for some smaller customers (10-24 station) and appear to be suffering from intermittent lock-ups of the SNOM phones attached. Obviously we are running Asterisk for the gateway, but I was

We are currently considering the Linksys POE switch for a small Asterisk office deployment. There will be no separate wiring closet to put it in. Can anybody tell me if this switch has a loud fan? Users would not be able to tolerate a loud noise close by. Otherwise we will go with a fanless desktop switch. Thanks, -- Andres

Hi List; Can someone advise me if Polycom support H323 that work fine with Asterisk? And wether this H323 Polcyom devices more costly than SIP Polycom. Also, I am not able to know if new Polycom come with PoE adaptor so no need for PoE Switch (can use normal switch that does not support PoE)? Do I need any special cable for Polycom or normal Ethernet cable? Regards Bilal

Hi all, For a top quality setup, I will need to install high quality VoIP switches with QoS and PoE. My potential customer should not have any problem with call quality. Experienced folks, Please advice me what switches to install and at what price. I may need it for upto 100 phones. What else should I consider so that phones work without problem along with the computers on the same network?

As an alternative to the "expensive" PoE switches out there, I found the D-Link Web Smart DES-1316 switch for just around $400. Now, the issue is, it does 802.3af power and, as I've found out through previous discussions, this original 76?0 series phones (the non G variety) do not use 802.3af. So I'm assuming I just need to use the special cable thing as per

2011/11/30 Mike <list at net-wall.com> > Hi Olivier,**** > > ** ** > > It if occurs only on the sidecar, I would imagine this is either a > defective sidecar/Polycom phone, or a defective PoE switch not giving > enough power. Changing PoE port would eliminate of confirm the PoE port > being the issue, but I?m betting on a Polycom defect.**** > > ** ** > >

Pardon, this might be off-topic. I'm reading: http://en.wikipedia.org/wiki/Network_switch For a setup of ~5 agents, would I be wrong in thinking that a generic 16 port unmanaged switch would fit the bill? The first model to come up for me in an Amazon search is: http://support.netgear.com/product/fs116 Is this a reasonable choice? Would I be wrong in thinking that most any Fast

> > Allen Casteran wrote: > > Anyone know what the POE draw is for the Aastra 480i phones? > > We have switches that will do 15 watts on 12 ports but only do 7.7 watts on all 24 ports. > > A Cisco 3560 switch will do 15.6 watts on all 24 ports. > > Just trying to find out if we need that much power. > Drew wrote: > According to Aastra tech support, 5 watts