similar to: IPv6 subnet routing

I have 2 nodes nodeA and nodeB I'm using tinc 1.1pre11 -- nodeA(fd80:2015:2105:abcd::1) : $ ip -6 route fd80:2015:2105:abcd::1 dev tun0 proto kernel metric 256 fd80:2015:2105:adcd::/64 dev tun0 metric 1024 fe80::/64 dev eth0 proto kernel metric 256 $ ping6 fd80:2015:2105:abcd::1 PING fd80:2015:2105:abcd::1(fd80:2015:2105:abcd::1) 56 data bytes 64 bytes from fd80:2015:2105:abcd::1:

You have a typo in your routes: fd80:2015:2105:adcd::/6 abcd vs. adcd On 21 May 2015, at 19:35, Martin <martinmoen at gmail.com<mailto:martinmoen at gmail.com>> wrote: I have 2 nodes nodeA and nodeB I'm using tinc 1.1pre11 -- nodeA(fd80:2015:2105:abcd::1) : $ ip -6 route fd80:2015:2105:abcd::1 dev tun0 proto kernel metric 256 fd80:2015:2105:adcd::/64 dev tun0 metric 1024

Hi all I feel like I should know the answer to this question, like I read it someplace sometime, but it evades me right now. It's also an opportunity to say hello to the list and many thanks for writing and supporting tinc vpn! We make great use of it at rhizomatica. So, Let's take this example setup. I have two tinc nodes (A and B) behind a firewall NodeA and NodeB have 192.168.1.2

Hi Guus, I've been a huge fan of the GraphDumpFile parameter in tinc -- it certainly beats sending USR2 to tincd, and ploughing through syslog to figure out which nodes are connected. Could I request that GraphDumpFile dumps a little more data to the file, namely, the subnet; changing the output file from (for example): digraph { nodeA [label = "nodeA"];

I have an rsync server running on nodeA and a client, nodeB. I am attempting to do a sync/copy from the local machine, nodeB, to the rsync server, nodeA. The following line from the rsync man page makes it look like this is relatively simple: for copying from the local machine to a remote rsync server. This is invoked when the destination path contains a :: separator or a rsync:// URL. I have

llseek requires ocfs2 inode lock for updating the file size in SEEK_END. because the file size maybe update on another node. if it not . after call llseek in SEEK_END. the position is old. this bug can be reproduce the following scenario: at first ,we dd a test fileA,the file size is 10k. on NodeA: --------- 1) open the test fileA, lseek the end of file. and print the position. 2) close the test

Hi, When I tested xm new command without uuid parameter repeatedly, I saw many same managed domain as follows. # xm list Name ID Mem VCPUs State Time(s) Domain-0 0 941 2 r----- 51.9 # xm new /xen/vm1.conf Using config file "/xen/vm1.conf". # xm new /xen/vm1.conf Using config file

Dear friends, How do I stop partial matching of list names? e.g., x <- list(AAAA="aaaaa", BBBBB="bbbbb") is.null(x$A) #returns FALSE even though there is no element A. if(is.null(x$A)) {result <- x$BBBB} else {result <- x$A} result #is aaaa even though there is no x$A element x <- list(CCCC="aaaaa", BBBBB="bbbbb") if(is.null(x$A))

I've the following error : Doing a node status request to the domain master browser at IP aaaa.bbbb.cccc.dddd failed First time I configure my smb.conf file on a server with the adress aaaa.bbbb.cccc.dddd For some raison I have to change this address for another. When I restart samba I the message : nmbd/nmbd_browsesync.c:get_domain_master_name_node_status_fail(486)

Thanks for the previous tips and suggestions. Here's a more concise example: Input file: <aaaa> <bbbb> <cccc> <dddd> I want everything on one line, i.e., remove all newlines. Like so: <aaaa><bbbb><cccc><dddd> Simple perl code: #!/usr/bin/env perl # Remove newlines from a file in two ways: # (1) Just "chomp" them; # (2) Replace

I can't get IPv6 routing to configure correctly despite everything I've read saying it should This is my network config on a fully-updated CentOS 5.8 system: # cat /etc/sysconfig/network NETWORKING=yes NETWORKING_IPV6=yes HOSTNAME=my.hostname.com GATEWAY=aaa.bbb.ccc.ddd IPV6_DEFAULTGW=2a02:aaaa.bbbb::1 IPV6_DEFAULTDEV=eth0 # cat /etc/sysconfig/network-scripts/ifcfg-eth0

Dear all, I have a lot of problems on R-programming. for example my csv. file is .. Date wrfRH wrfsolar wrfwindspeed wrfrain wrftd wrfta 21/10/2010 92.97 22.11 53.27 0 1546.337861 61.00852664 22/10/2010 87.35 21.99 40.89 0 1300.408288 62.85352227 23/10/2010 88.38 21.71 28.04 0.01 1381.768284 54.80594493 24/10/2010 92.32 15.45 22.38 0.51 1113.90981 39.46573663 25/10/2010 93.42

Hi Guys, I have now updated to 4.5.0 - thank you to all the team for your efforts on this :) I was excited to read in the release notes that there were many replication improvements, and I have run 'samba-tool dbcheck --cross-ncs --fix' on all my DCs; there were many, many replPropertyMetaData and other errors which have now been found and fixed - thanks! However, I think something

I have already a linux PDC with LDAP-Samba 3.3. Now i want to install BDC which will work if my PDC goes down. Pleases help me out. Thanks kamal

quoted from http://www.tinc-vpn.org/examples/redirect-gateway/ "In fact, one does not have to set the VPN_GATEWAY variable at all. In switch mode, the gateway routes are necessary" i don't get it. it's is too short to understand. is VPN_GATEWAY set by tinc in switch mode? and why is "In switch mode, the gateway routes are necessary" mentioned here suddenly? afaik,

Has anyone ever used UUID in a migration? I thought I could set the default value of a field to be ‘UUID’ but that only sets the value the string instead of executing the function to create a new unique identifier. -- Posted via http://www.ruby-forum.com/. --~--~---------~--~----~------------~-------~--~----~ You received this message because you are subscribed to the Google Groups "Ruby

I have been using shorewall and freeswan successfully for 3 or more years now. But they have all been using the Linux 2.4 kernel. My current configuration is (as the title suggests) using SuSE 9.1 which has a 2.6.5 kernel and freeswan 2.0.4 built-in. After much reading and a lot of trial and error, I did get this combination to work with Shorewall 2.0.9. It is happily talking to an older Mandrake

Hi all, This is the second take of a patch that I submitted some time ago for allowing specifying vcpu pinning taking NUMA nodes into account. IOW, something like this: * "nodes:0-3": all pCPUs of nodes 0,1,2,3;  * "nodes:0-3,^node:2": all pCPUS of nodes 0,1,3;  * "1,nodes:1-2,^6": pCPU 1 plus all pCPUs of nodes 1,2    but not pCPU 6; v1 was a single patch, this is

Hi! I need some help to finish my script. I have two tables that I combine randomly to produce a third table. This I do for hundreds of iterations. In the output file I get all the simulated tables after each other. It looks like this (in this case 3 iterations): output file: [[1]] [,1] [,2] [,3] [1,] "GM030005" "WI920024" "CCCC" [2,]

Guus Sliepen [2016-05-24 11:26 +0200] : > On Tue, May 24, 2016 at 08:17:07AM +0200, Niklaas Baudet von Gersdorff wrote: [...] > > A $ cat /usr/local/etc/tinc/klaas/tinc-up > > ifconfig $INTERFACE inet6 fd16:dcc0:f4cc:0:0:1:0:1 prefixlen 80 > > route -6 add -host fd16:dcc0:f4cc:0:0:2:0:1 fd16:dcc0:f4cc:0:0:1:0:1 > > route -6 add -net