similar to: IBM x3500 M3 and CentOS 7.*

Hello, Can you please help. Which versions of Centos 6 and 7 support Multi Stream Transport (MST) on DisplayPort graphics. Regards, Mark Woolfson MW Consultancy Ltd Leeds LS18 4LY West Yorkshire United Kingdom Tel: +44 113 259 1204 Mob: +44 786 065 2778 Em: julie at mwcltd.co.uk (Commercial) Em: mrw at mwcltd.co.uk (Technical) Web: www.mwcltd.co.uk

Hello, I have a pre-production Intel Skylake server using dual 8176 processors (28 core @2.1Ghz) I have loaded from the DVD distribution CentOS 7.3 and RHEL 7.4 with no problems. When I try and load CentOS 6.9 the boot process hangs just as the Anaconda graphics is started for CentOS configuration. If I use a secondary graphics card then the process completes with no problems and CentOS boots

Hello, I have an Intel NUC7PJYH running CentOS 6.8. This is a NUC with standard USB, 1GbE and 2*HDMI. Installation was no problem providing acpi=off. The problem is that by default the two displays are mirrored and I can?t seem to separate them. I can only see one HDMI port from CentOS. I need to see both HDMI ports discreetly. Can you please help. Regards, Mark Woolfson MW Consultancy Ltd

Hi John, why not try something newer than CentOS 6.8 ? Maybe not the latest 8.1 but 7.7 is quite recent and stable. Your (integrated) video card is : Intel? HD Graphics 605 (NUC7PJYH) Intel NUC7PJYH seems to be able to pilot Dual 4K display : " ...The NUC7PJYH kit also comes with dual Ultra HD 4K display support via two full-sized HDMI* ports, consumer infrared, and a TOSLINK audio jack,

CentOS 6.9 has support for the Haswell processor which is a subset of the Skylake. All Skylake server ancillary components work perfectly with CentOS 6.9. The AST2500 used with the Skylake is very good and will process UHD. However this is not backwards compatible with legacy variants. To make it work an ancillary graphics card is required which is less than $100. This will not break the

Good afternoon, I've been using CentOS for many, many years. I'm looking for a good laptop with 4 cores that has an NVIDIA GPU with dedicated memory. I'd prefer a GTX 10** series but the older 9** series is fine. Any recommendations? Thanks! Jeff

Hello, There was a support issue with the Intel Skylake and CentOS 6.* where the graphics hardware was not supported. Intel have now come up with a software solution to support the AST2500 graphics hardware on the Skylake. Regards, Mark Woolfson MW Consultancy Ltd Leeds LS18 4LY United Kingdom Tel: +44 113 259 1204 Mob: +44 786 065 2778 --- This email has been checked for viruses by AVG.

Hello, Is the Intel Celeron J5005 processor supported on CentOS 6.8. If not, is there a CentOS version which supports this processor. Regards, Mark Woolfson MW Consultancy Ltd Leeds LS18 4LY United Kingdom Tel: +44 113 259 1204 Mob: +44 786 065 2778

On Sun, Apr 19, 2020 at 9:40 AM Mike <1100100 at gmail.com> wrote: > > Thought it might also be helpful to confirm that firewalld is not > interfering in any way. > > what is the output of ~$# systemctl status firewalld Thanks Mike. # systemctl status firewalld Unit firewalld.service could not be found. Jeff

Hello Andy, The CentOS 6.9 kernel we are using is 2.6.32-696.el6.x86_64. Regards, Mark Woolfson MW Consultancy Ltd Leeds United Kingdom Tel: +44 113 259 1204 Mob: +44 786 065 2778 -----Original Message----- From: Andreas Benzler Sent: Wednesday, May 31, 2017 9:54 AM To: CentOS mailing list Subject: Re: [CentOS] CentOS 6.9 Skylake soft error Hello Mark, which kernel you use? Sometimes it is

I've recently set up a system built on an ASUS P5E-VM HDMI motherboard running Ubuntu 7.10 and I'm experiencing some very noticeable tearing during video playback with mplayer. I have read some discussion about video tearing with other Intel chipsets in the mailing list a while back but hadn't heard much about it lately. I've experimented with both xv and gl video output as well

>From what I remember the 3650 M2 has got some diagnostic LED's on the rear panel. Do these turn on and cycle? Regards, Mark Woolfson MW Consultancy Ltd Leeds United Kingdom Tel: +44 113 259 1204 Mob: +44 786 065 2778 -----Original Message----- From: John R Pierce Sent: Wednesday, February 22, 2017 9:43 PM To: centos at centos.org Subject: Re: [CentOS] OT: hardware, IBM 3650 M2

John R Pierce wrote: > On 2/22/2017 1:16 PM, m.roth at 5-cent.us wrote: >> a) Please don't top post. >> b) 'T'ain't funny, McGee. They don't have the budget, and they need this >> server*now*... it's one of their compute nodes, and at least one person >> is dead in the water. > > you can't afford a replacement for a 6-8 year old server

Hello, I have an Intel NUC6i5 (Skylake i5-6260u processor) running CentOS 6.9 and there are no real problems. However during boot an error occurs in dmesg where a PCH unknown device 0x9d48 is logged. How can I get rid of this error output? Thank you, Mark

hi, I am planning to replace my old CentOS 6 mail server soon. Most details are quite obvious and do not need to be changed, but the old system was running on spinning discs and this is certainly not the best option for todays mail servers. With spinning discs, HW-RAID6 was the way to go to increase reliability and speed. Today, I get the feeling, that traditional RAID is not the best option for

Hello, Where do I find kernel-ml? Regards, Mark Woolfson -----Original Message----- From: Nux! Sent: Wednesday, April 12, 2017 5:18 PM To: CentOS mailing list Subject: Re: [CentOS] Re CentOS and Intel graphics Give kernel-ml a try, else try CentOS 7. -- Sent from the Delta quadrant using Borg technology! Nux! www.nux.ro ----- Original Message ----- > From: "Mark (Netbook)"

Hello, I have an Intel NUC7i3 with 620 graphics and an Intel NUC7i7 with 640 graphics. I have loaded CentOS 6.9 and the graphics is not fully working. I believe that I need a driver. Does CentOS support the Intel 620 and 640 graphics and if not, can someone please point me in the direction of the drivers, with install instructions. Regards, Mark Woolfson

Hello Everyone, Whenever purchasing hardware we make it an effort to validate OS, driver and now hypervisor compatibility. Being a low budget company, we really look for the best bang for the bug. Right now that happens to be: x3755 M3 brandishing the AMD SR5690 chipset. We plan on installing a QLogic fiberchannel and a graphics card that support PCI passthrough. Before doing anything we are

I'm trying to install CentOS 5.5 on a couple of servers of type IBM System x3550 M3, but it's not going too well. Actually, the install setup phase runs as expected, and the actual installation also appears to be successful, but the system will not boot - I just get a message (presumably) from BIOS saying that boot from hard disk 0. If I start the installer again after this, or boot

Hello. I've got a quartet of IBM x3630 M3 with one that is frequently hard locking under heavy NFS load. I am running 9.0-RELEASE with all the patches from freebsd-update. My problem machine has 8 16 core clients, each doing IO intensive tasks connected to it via a Procurve and the onboard igb0 interface. Mostly network reads, typically 10MB read per MB written. When the machine locks