similar to: Intel Skylake Server

CentOS 6.9 has support for the Haswell processor which is a subset of the Skylake. All Skylake server ancillary components work perfectly with CentOS 6.9. The AST2500 used with the Skylake is very good and will process UHD. However this is not backwards compatible with legacy variants. To make it work an ancillary graphics card is required which is less than $100. This will not break the

Hello, There was a support issue with the Intel Skylake and CentOS 6.* where the graphics hardware was not supported. Intel have now come up with a software solution to support the AST2500 graphics hardware on the Skylake. Regards, Mark Woolfson MW Consultancy Ltd Leeds LS18 4LY United Kingdom Tel: +44 113 259 1204 Mob: +44 786 065 2778 --- This email has been checked for viruses by AVG.

Hello, Can you please help. Which versions of Centos 6 and 7 support Multi Stream Transport (MST) on DisplayPort graphics. Regards, Mark Woolfson MW Consultancy Ltd Leeds LS18 4LY West Yorkshire United Kingdom Tel: +44 113 259 1204 Mob: +44 786 065 2778 Em: julie at mwcltd.co.uk (Commercial) Em: mrw at mwcltd.co.uk (Technical) Web: www.mwcltd.co.uk

Hello, Please can anyone help with the problem below when trying to install CentOS 7.6 on an IBM x3500 M3 from DVD or USB. CentOS 7.5 installs perfectly with no errors. CentOS 7.6 tries to boot, an error is output briefly and the workstation powers down. CentOS 7.7 displays the error briefly then continues the install with no further errors. I also tried RHEL 7.6 which installs perfectly with

Hello Andy, The CentOS 6.9 kernel we are using is 2.6.32-696.el6.x86_64. Regards, Mark Woolfson MW Consultancy Ltd Leeds United Kingdom Tel: +44 113 259 1204 Mob: +44 786 065 2778 -----Original Message----- From: Andreas Benzler Sent: Wednesday, May 31, 2017 9:54 AM To: CentOS mailing list Subject: Re: [CentOS] CentOS 6.9 Skylake soft error Hello Mark, which kernel you use? Sometimes it is

Hello, I have an Intel NUC6i5 (Skylake i5-6260u processor) running CentOS 6.9 and there are no real problems. However during boot an error occurs in dmesg where a PCH unknown device 0x9d48 is logged. How can I get rid of this error output? Thank you, Mark

Good afternoon, I've been using CentOS for many, many years. I'm looking for a good laptop with 4 cores that has an NVIDIA GPU with dedicated memory. I'd prefer a GTX 10** series but the older 9** series is fine. Any recommendations? Thanks! Jeff

Hello, Is the Intel Celeron J5005 processor supported on CentOS 6.8. If not, is there a CentOS version which supports this processor. Regards, Mark Woolfson MW Consultancy Ltd Leeds LS18 4LY United Kingdom Tel: +44 113 259 1204 Mob: +44 786 065 2778

On Sun, Apr 19, 2020 at 9:40 AM Mike <1100100 at gmail.com> wrote: > > Thought it might also be helpful to confirm that firewalld is not > interfering in any way. > > what is the output of ~$# systemctl status firewalld Thanks Mike. # systemctl status firewalld Unit firewalld.service could not be found. Jeff

Hello, I have an Intel NUC7PJYH running CentOS 6.8. This is a NUC with standard USB, 1GbE and 2*HDMI. Installation was no problem providing acpi=off. The problem is that by default the two displays are mirrored and I can?t seem to separate them. I can only see one HDMI port from CentOS. I need to see both HDMI ports discreetly. Can you please help. Regards, Mark Woolfson MW Consultancy Ltd

Hi John, why not try something newer than CentOS 6.8 ? Maybe not the latest 8.1 but 7.7 is quite recent and stable. Your (integrated) video card is : Intel? HD Graphics 605 (NUC7PJYH) Intel NUC7PJYH seems to be able to pilot Dual 4K display : " ...The NUC7PJYH kit also comes with dual Ultra HD 4K display support via two full-sized HDMI* ports, consumer infrared, and a TOSLINK audio jack,

You need at least a newer kernel. If you like you can try out http://elrepo.org/tiki/tiki-index.php <http://elrepo.org/tiki/tiki-index.php> With 3.10 I?m personal unsure kernel-lt-3.10.104-1.el6.elrepo.x86_64.rpm <http://elrepo.reloumirrors.net/kernel/el6/x86_64/RPMS/kernel-lt-3.10.104-1.el6.elrepo.x86_64.rpm> But got here centos with 4.11.3 running quiet well.

Hi -- I have found a bug in an HPC code where llvm is vectorizing a loop on Skylake that has an obvious recurrence. I derived a small test case based on the original benchmark below: /*****************************************************************/ static void __attribute__ ((always_inline)) one( const int *restrict in, const int *const end, const unsigned shift, int *const restrict index,

Hi, I have a JIT compiler using the legacy JIT on LLVM 3.5 that, when run on the Xeon v5 Skylakes produces "Cannot select: intrinsic %llvm.x86.sse41.round.sd". Note, this does not occur on i7 Kabylakes. To get this far I had to disable AVX512 code gen. Upgrading the system I am looking at from 3.5 to a later version is a big job that I'd prefer not to have on my critical path.

Thank you. I'm letting it auto detect by setting the target using getProcessTarget. I disabled avx512 support by passing -avx512f (and the other variants) to setMAttrs on EngineBuilder. I can see refs to avx512 in X86.td. It's the exact same executable running on Kabylake. What does the Cannot select: specifically mean? Is there some table that doesn't have a definition for a key in

getProcessTriple just determines operation system, and architecture. It doesn't deal with specific instruction set features. The CPU should be controlled by MCPU on the EngineBuilder i think. The CPU autodetection code lives in getHostCPUName in lib/Support/Host.cpp, but I don't think the JIT calls into. I think its expected the user would call it or pass a specific CPU string to the MCPU

I have this code, which works fine on MacOS and Linux hosts: const char *target_specific_cpu_args; const char *target_specific_features; if (g->is_native_target) { target_specific_cpu_args = ZigLLVMGetHostCPUName(); target_specific_features = ZigLLVMGetNativeFeatures(); } else { target_specific_cpu_args = ""; target_specific_features =

On 07/12/2016 03:36 AM, Yamaban wrote: > On Tue, 12 Jul 2016 10:15, Walter H. wrote: >> >> Hello, >> >> can CentOS 6.8 be run on a mini-PC like this? >> https://www.zotac.com/product/mini_pcs/zbox-ci323-nano >> >> would like to configure this as a Firewall, and this should be instead of >> my router (integratet firewall, NAT) and wlan-ap >>

I suspect that there are 2 issues here: * I have incorrect alignment somewhere * MSVC / .pdb / CodeView debugging is not working correctly. I think the latter would help solve the former. I will send out a new email later talking about the issues I'm having debugging llvm-generated binaries with MSVC. On Sat, Sep 30, 2017 at 3:33 PM, Andrew Kelley <superjoe30 at gmail.com> wrote:

Hi all, On my recent MSI Apache Pro laptop with Intel Skylake + GP106M Nvidia chip, i am unable to use the external HDMI and DP outputs. The outputs are available thru xrandr and can be activated, but the connected monitors always show a black screen. Note that the integrated LCD is connected to the Skylage GPU, while the HDMI and DP outputs are connected to the NVIDIA GP106M GPU. The