similar to: old hardware / minimal netinstall -> CPU fan control

Fred Smith wrote: > On Tue, Jul 11, 2017 at 12:05:55PM +0100, Gary Stainburn wrote: >> I have just installed CentOS 6 i386 onto an old rack server (it's gonna >> be a Bacula storeage server and is a 1U 1/2 depth chassis) >> >> I did a minimum netinstall and so far so good. However, I have one >> problem. >> The CPU fan is going at full speed constantly.

Warning:I'm new to CentOS and have not tested the suggestion below (with Linux). So please research if it sounds like a good idea. It may be worth trying to bypass the issue by installing VMware ESXi and setting up CentOS as a virtual machine. This will give you additional control and backup options for the system. Gavin On Wed, 12 Jul 2017, 04:22 <m.roth at 5-cent.us> wrote: >

On Tue, Jul 11, 2017 at 12:05:55PM +0100, Gary Stainburn wrote: > I have just installed CentOS 6 i386 onto an old rack server (it's gonna be a > Bacula storeage server and is a 1U 1/2 depth chassis) > > I did a minimum netinstall and so far so good. However, I have one problem. > The CPU fan is going at full speed constantly. Not a real problem apart from > (a) it will

I have just installed CentOS 6 i386 onto an old rack server (it's gonna be a Bacula storeage server and is a 1U 1/2 depth chassis) I did a minimum netinstall and so far so good. However, I have one problem. The CPU fan is going at full speed constantly. Not a real problem apart from (a) it will affect the fan's lifespan and (b) it's noisy. I've done some Googling and found

on centos 7 I tried to install banshee from EPEL yum install banshee gotting this error: Error: Package: banshee-2.6.2-11.el7.x86_64 (epel) Requires: libgpod-sharp >= 0.8.2 You could try using --skip-broken to work around the problem You could try running: rpm -Va --nofiles --nodigest seems known problem but ignored to fix it in a year or more:

On Thu, Jul 12, 2018 at 07:27:58PM -0500, Chris Adams wrote: > > Default Gateway IP : 192.168.0.100 > > Default Gateway MAC : 00:25:90:0a:42:87 > > No, that does not look right. You have configured the gateway of the > IPMI to be the host OS side of the NIC. You can't do that... in a lot > of systems I've seen, the IPMI side of the NIC can't even

Hi! I've installed Centos 4.4 on a machine at work (it's a HP Proliant DL-320 G2 rackmout server that serves my desktop). In recent days (Centos 4.4 has only been installed for a little over a week), like, since Wed or Thu last week, every time I reboot Kudzu wants to remove the network adaptors then reinstall them and breaks the network. I've gone to the point of disabling one of

Is it possible to access the described class in a shared behavior? I''m trying to do something like this: describe "Siberian feline", :shared => true do described_class_instance_as :feline, :name => "fluffy", :breed => "Siberian" # or maybe before(:all) do @feline = described_class.new(:name => "fluffy", :breed =>

---------------------------- Original Message ---------------------------- Subject: ipmitool and CentOS 7 From: m.roth at 5-cent.us Date: Mon, May 16, 2016 16:57 To: "CentOS" <centos at centos.org> -------------------------------------------------------------------------- On Dells running CentOS 6, we could use this command ipmitool delloem lcd set mode userdefined

Hallo *! I have a board SE7501HG2. - On 2.6.18 ipmitool works succefull. On Xen-3.1 (2.6.18) ipmitool say: # ipmitool sensor WARNING: Unknown SDR repository version 0x00 SDR record id 0x0000: invalid length 0 (see thread [ipmitool-devel] Unknown SDR version) - On page [4] as written: ipmitool -> BMC ---> i2c/smbus ''-> SDR - On Thread [9] was written:

Hello everyone -- I am stumped on this issue, mostly because I'm not quite sure if it's behaving correctly or not. I believe this used to work and right now I'm not quite sure why it's no longer doing so and how to fix it (if possible). I suspect it is because of my recent update of the OS and Samba version. When users are trying to follow a symlink that goes to a different

Well. i got s.th. for you and i think i'll give this to crazney (lhl.linuxgames.com) #1 a step by step HL tutorial #2 my questions. -------------------------------------------------------------------------- ## 1 ## a step by step HL tutorial ###################################### -------------------------------------------------------------------------- yea, well, i got HL working. On my

Got an older server running 6.5. I've been fighting it - I have two webcams for surveillance of the room; one works with motion, but it resizes the picture down Adjusting resolution from 640x480 to 360x296 and the video's dark and bad contrast. So I went back to the camer I'd been using before that worked fine... on CentOS 5.x, and then I remembered why I'd gone to the other camera

Hello folks, I'm having a difficult time trying to figure out why the CPU cooling fans run at full speed on my Supermicro X8DAL-3 motherboard. There doesn't seem to be any variable speed (the fans are PWM compatible) ... they either idle at almost nothing, or suddenly burst into a high-pitched scream that gets my ears bleeding after a few seconds. Once they jump to warp-10, they

Jon Pruente wrote: > On Tue, Jun 26, 2018 at 3:16 PM, mark <m.roth at 5-cent.us> wrote: > >> The man page isn't helping, nor have I been able to find examples that >> work. >> >> For example, the man page claims I can do ipmitool lan get active, and >> I try, and it says, "invalid lan command, get". > > get isn't a recognized

I've used ipmitool any number of times, but never for more than getting info, or setting the server name on a Dell LCD screen. However, I had a server screaming about intruder alert, intruder alert, er, "Chassis intrusion detected", and I thought there might be a way to shut it up (this after pulling the server and reseating the lid). A quick google found, on the first page, an 8

CentOS Errata and Security Advisory 2011:1814 Moderate Upstream details at : https://rhn.redhat.com/errata/RHSA-2011-1814.html The following updated files have been uploaded and are currently syncing to the mirrors: ( sha256sum Filename ) i386: 583c451e1c1759ab60d296f761dd14f97e22107894fbfc8d0825ccc327caa050 ipmitool-1.8.11-12.el6_2.1.i686.rpm x86_64:

Michael C. Tiernan wrote: > ipmitool -I open lan get *NUMBER* > Description: CentOS Linux release 7.5.1804 (Core) Release: 7.5.1804 ipmitool -I open lan get 1 Invalid LAN command: get I'm saying that the get command with lan DOES NOT WORK. ipmitool doesn't understand it.... <SNIP> mark

On Tue, Jun 26, 2018 at 3:16 PM, mark <m.roth at 5-cent.us> wrote: > The man page isn't helping, nor have I been able to find examples that > work. > > For example, the man page claims I can do ipmitool lan get active, and I > try, and it says, "invaling lan command, get". > get isn't a recognized subcommand under lan in the ipmitool I have installed.

CentOS Errata and Bugfix Advisory 2013:1259 Upstream details at : https://rhn.redhat.com/errata/RHBA-2013-1259.html The following updated files have been uploaded and are currently syncing to the mirrors: ( sha256sum Filename ) i386: 2267fa0eb54642d8bbef3878082298e9034e85e6f4a0175c36b8b9724b06f253 ipmitool-1.8.11-16.el6.i686.rpm x86_64: