similar to: Re: attaching storage pool error

Hi! Report from my multipath tests today. My test virtual machine, that runs from an NPIV pool, is not able to use multipath. When I pulled the cable from one of the targets, it crashed. But, strangely, it could boot up again on that other path, that it just crashed on. That tells me it can use both paths, and is not limited to one of them only, but because the multipath layer isn't

Hi, John, and thank you! This was a very thorough and welcome response, I was wondering where all the storage guys were... I will get back to you with more details later, specifically about multipath, since this needs to be investigated thoroughly. I have, with trial and error method, during the elapsed time, been able to attach the NPIV pool LUN to a virtio-scsi controller, and it seems it

On 08/24/2016 06:31 AM, Johan Kragsterman wrote: > > Hi again! > I saw this last week while I was at KVM Forum, but just haven't had the time until now to start thinking about this stuff again ... as you point out with your questions and replies - NPIV/vHBA is tricky and complicated... I always have try to "clear the decks" of anything else before trying to page how this

Hi! Got a couple of storage questions here. I'm a storage guy, running a new project, and just started with libvirt, but have been using qemu/kvm on other platforms before, as well as oVirt. So, my questions here: I started with creating a vhba, and that went fine, I could see it on the storage side logging in to the target with its wwn. My next step would be to make it persistent, and

Thank you for your reply, I'm still getting hard time to attach the hostdev, I couldn't make it work out of the doc. I took the address details from: # ll /sys/bus/scsi/devices/7:* lrwxrwxrwx 1 root root 0 Feb 8 12:58 /sys/bus/scsi/devices/7:0:0:0 -> ../../../devices/pci0000:00/0000:00:03.0/0000:08:00.1/host7/rport-7:0-0/target7:0:0/7:0:0:0 lrwxrwxrwx 1 root root 0 Feb 8 12:58

Hi, When I want to use NPIV for a FC HBA in my Linux machine, I got the below error msg in virsh: virsh # nodedev-create /home/kvm/vHBA.xml error: Failed to create node device from /home/kvm/vHBA.xml error: internal error Parent device scsi_host20 is not capable of vport operations I checked the /sys/class folder for my HBA device that I want to use its NPIV feature, it's there:

Hi, I'm trying to attach a host FC HBA to VM (NPIV). Running ovirt 3.5 on CentOS 6.7, libvirt-0.10.2-46.el6_6.6.x86_64, I created vHBA using nodedev-create command - see below HBA and vHBA. I wrote a vdsm hook which appends the vHBA xml stanza to the devices xml element but the vm start starts without the vHBA device. Also, when trying to attach the device manually as a live device - I get:

Before posting it to WIKI or somewhere, I want to see if there is any suggestions on it, or if I missed something. ============================================ How to use NPIV in libvirt I planned to wrote a document about how to use NPIV in libvirt after more features are supported, but it looks like I can't wait till then, got lots lots of questions from both the

Thanks for John Ferlan's lots of internal feedbacks, I believe it's more readable, and better orgnized now. Should we create a page for it under http://libvirt.org/deployment.html or add it in WIKI? ========================================== NPIV in libvirt NPIV (N_Port ID Virtualization) is a Fibre Channel technology to share a single physical Fibre Channel HBA with multiple virtual

I'm missing something. The purpose of NPIV (as I understand it) is to give a guest OS an HBA that it can scan, play with new luns, etc all without making changes to the physical server(s) the guest is living in currently. However, I can't find a way to either have the guest's XML config create the HBA or for the physical server to successfully GIVE the HBA to the guest. I can give

Link: http://wiki.libvirt.org/page/NPIV_in_libvirt Topic: Virtual machine configuration change to use vHBA LUN There is a NPIV storage pool defined on two hosts and pool contains a total of 8 volumes, allocated from a storage device. Source: # virsh vol-list poolvhba0 Name Path ------------------------------------------------------------------------------ unit:0:0:0

Is this possible: I would like to have a VM use a FC LUN exported to a virtual wwn (using NPIV) as its primary disk. I was thinking there might be a mechanism to say VM, boot using a LUN with this vwwn as your primary disk? Thanks in advance. -- --------------------------------------------------------------------- Eric Ross HPC Systems Administrator Argonne National Laboratory Leadership

On 02/08/2016 06:01 PM, Vaknin, Rami wrote: > Thank you for your reply, > I'm still getting hard time to attach the hostdev, I couldn't make it work out of the doc. > > I took the address details from: > > # ll /sys/bus/scsi/devices/7:* > lrwxrwxrwx 1 root root 0 Feb 8 12:58 /sys/bus/scsi/devices/7:0:0:0 ->

On 01.02.2016 22:48, Vaknin, Rami wrote: > Hi, > > I'm trying to attach a host FC HBA to VM (NPIV). > > Running ovirt 3.5 on CentOS 6.7, libvirt-0.10.2-46.el6_6.6.x86_64, I created vHBA using nodedev-create command - see below HBA and vHBA. > I wrote a vdsm hook which appends the vHBA xml stanza to the devices xml element but the vm start starts without the vHBA device.

Hello, I am trying to find out a best practice for a specific scenario. First of all I would like to know what is the proper way to set up multipath, who should care about it the host or the guest. Right now I have a setup where I have one multipath which sets my host to boot from FC SAN. I have another multipathed LUN in the host which is essentially a dm which I attached to a guest, however

On 06/20/2013 11:07 AM, Dennis Chen wrote: > Hi, > > When I want to use NPIV for a FC HBA in my Linux machine, I got the below > error msg in virsh: > > virsh # nodedev-create /home/kvm/vHBA.xml > error: Failed to create node device from /home/kvm/vHBA.xml > error: internal error Parent device scsi_host20 is not capable of vport > operations > > I checked the

Hi, I am using the libvirt 1.0.6 with the patch applied: http://libvirt.org/git/?p=libvirt.git;a=commitdiff;h=371c155 The problem I encountered is, with virsh comand 'nodedev-create /home/kvm/vHBA.xml', the vHBA can be generated as expected on the host, but error msg will show in the virsh shell: libvirt: Node Device Driver error : Node device not found I try to find the reason with

Hi, i''m having problems attaching disks from a fc-san to a solaris 10 guest. xen host ist a opensolaris box "SunOS node1 5.11 snv_127 i86pc i386 i86xpv". my xen guest is named pg4. this command works fine. virsh attach-disk pg4 /dev/dsk/c8t600A0B800029D69A000013CA4B00E1ABd0 hdb and before i was able to import this volume as a zpool on the xen host - so connection to this

I am getting the following on 'make install' on Cygwin both on debug and release builds :- llvm[3]: Installing Release /home/ang/llvm-coff/bin/llvmc.exe make[3]: Leaving directory `/home/ang/build/llvm-coff/tools/llvmc/driver' make[2]: Leaving directory `/home/ang/build/llvm-coff/tools/llvmc' make[1]: Leaving directory `/home/ang/build/llvm-coff/tools' make[1]: Entering

Hi Aaron, Which revision are you building? Assuming TOT, it's possible this is a bug that I introduced/triggered with the name changes. I know nothing of the status of cygwin however, can you confirm that this used to work? If you use r77097, does it work? - Daniel On Sun, Jul 26, 2009 at 4:23 AM, Aaron Gray<aaronngray.lists at googlemail.com> wrote: > I am getting an error