libvirt users - Sep 2013 - Doc v2: How to use NPIV in libvirt

Thanks for John Ferlan's lots of internal feedbacks, I believe it's more
readable, and better orgnized now. Should we create a page for it
under http://libvirt.org/deployment.html or add it in WIKI?

=========================================
NPIV in libvirt

NPIV (N_Port ID Virtualization) is a Fibre Channel technology to
share a single physical Fibre Channel HBA with multiple virtual ports.
Henceforth known as a "virtual port" or "virtual Host Bus
Adapter"
(vHBA), each virtual port is identified by its own WWPN (Word Wide
Port Name) and WWNN (Word Wide Node Name). In the virtualization
world the vHBA controls the LUNs for virtual machines.

The libvirt implementation provides flexibility to configure the LUN's
either directly to the virtual machine or as part of a storage pool
which then can be configured for use on a virtual machine.

NPIV support in libvirt was first added to libvirt 0.6.5; however, the
following sections will primarily describe NPIV functionality as of the
current libvirt release, 1.1.2. There will be a troubleshooting and prior
version considerations section to describe some historical differences.

1) Discovery

Discovery of HBA(s) capable of NPIV is provided through the virsh
command 'virsh nodedev-list --cap vports'. If no HBA is returned,
then the host configuration should be checked. The XML output from the
command "virsh nodedev-dumpxml" will list fields <name>,
<wwnn>, and
<wwpn> to be used in order to create a vHBA. Take care to also note
the <max_vports> value as this lets you know if the HBA is going to
exceed the maximum vHBA supported.

The following output indicates a host that has two HBAs to support
vHBA and the layout of a HBA's XML:

# virsh nodedev-list --cap vports
scsi_host4
scsi_host5

# virsh nodedev-dumpxml scsi_host5
<device>
<name>scsi_host5</name>
<parent>pci_0000_04_00_1</parent>
<capability type='scsi_host'>
<host>5</host>
<capability type='fc_host'>
<wwnn>2001001b32a9da4e</wwnn>
<wwpn>2101001b32a9da4e</wwpn>
<fabric_wwn>2001000dec9877c1</fabric_wwn>
</capability>
<capability type='vport_ops'>
<max_vports>164</max_vports>
<vports>5</vports>
</capability>
</capability>
</device>

The "max_vports" value indicates there are a possible of 164 vports
available for use in the HBA configuration. The "vports" value
indicates
the number of vports currently being used.

Support for detection of HBA's capable of NPIV support prior to libvirt
1.0.4 is described in the "Troubleshooting" section.

2) Creation of a vHBA using the node device driver

In order to create a vHBA using the node device driver, select an HBA with
available "vport" space, use the HBA "<name>" field as
the "<parent>"
field in the following XML:

<device>
<parent>scsi_host5</parent>
<capability type='scsi_host'>
<capability type='fc_host'>
</capability>
</capability>
</device>

Then create the vHBA with the command "virsh nodedev-create" (assuming
above XML file is named "vhba.xml"):

# virsh nodedev-create vhba.xml
Node device scsi_host6 created from vhba.xml

NOTE: If you specify "name" for the vHBA, then it will be ignored.
The kernel will automatically pick the next SCSI host name in sequence not
already used. The "wwpn" and "wwnn" values will be
automatically generated
by libvirt.

In order to see the generated vHBA XML, use the command "virsh
nodedev-dumpxml" as follows:

# virsh nodedev-dumpxml scsi_host6
<device>
<name>scsi_host6</name>
<parent>scsi_host5</parent>
<capability type='scsi_host'>
<capability type='fc_host'>
<wwnn>2001001b32a9da5e</wwnn>
<wwpn>2101001b32a9da5e</wwpn>
</capability>
</capability>
</device>

This vHBA will only be defined as long the host is not rebooted. In
order to create a persistent vHBA, one must use a libvirt storage pool
(see next section).

3) Creation of vHBA by the storage pool

By design, vHBAs managed by the node device driver are transient across
host reboots. It is recommended to define a libvirt storage pool based
on the vHBA in order to preserve the vHBA configuration. Using a storage
pool has two primary advantage, first the libvirt code will find the
LUN's path via simple virsh command output and second migration of
virtual machine's requires only defining and starting a storage pool
with the same vHBA name on the target machine if you use the LUN with
libvirt storage pool and volume name in virtual machine config (see
section 5).

In order to create a persistent vHBA configuration create
a libvirt 'scsi' storage pool using the XML as follows:

<pool type='scsi'>
<name>poolvhba0</name>
<source>
<adapter type='fc_host' wwnn='20000000c9831b4b'
wwpn='10000000c9831b4b'/>
</source>
<target>
<path>/dev/disk/by-path</path>
<permissions>
<mode>0700</mode>
<owner>0</owner>
<group>0</group>
</permissions>
</target>
</pool>

You must use the "type='scsi'" for the pool; The source
adapter
type must be "fc_host". Attributes "wwnn" and
"wwpn" are provided as
the unique identifier for the vHBA to be created.

There is an optional attribute "parent" for source the adapter. It
indicates the name of the HBA which you want to use to create the
vHBA. Its value should be consistent with what node device driver
dumps (e.g. scsi_host5). If it's not specified, libvirt will pick
the first HBA capable of NPIV that has not exceeded the maximum
vports it supports.

NOTE: You can also create a scsi pool with source adapter type
"fc_host"
for a HBA, and in that case the attribute "parent" is not necessary.

If you prefer to choose which parent HBA to use for your vHBA, then
you must provide the parent, wwnn, and wwpn in the source adapter XML as
follows:

<source>
<adapter type='fc_host' parent='scsi_host5'
wwnn='20000000c9831b4b'
wwpn='10000000c9831b4b'/>
</source>

To define the persistent pool (assuming above XML is named as
poolvhba0.xml):

# virsh pool-define poolvhba0.xml

NOTE: One must use pool-define to define the pool as persistent,
since a pool created by pool-create is transient and it will disappear
after a system reboot or a libvirtd restart.

To start the pool:

# virsh pool-start poolvhba0

To destroy the pool:

# virsh pool-destroy poolvhba0

When starting the pool, libvirt will check if the vHBA with same
"wwpn:wwpn" already exists. If it does not exist, a new vHBA with the
provided "wwpn:wwnn" will be created. Correspondingly，when destroying
the pool the vHBA is destroyed too.

Finally, in order to ensure that subsequent reboots of your host will
automatically define vHBA's for use in virtual machines, one must set the
storage pool autostart feature as follows (assuming the name of the created
pool was "poolvhba0"):

# virsh pool-autostart poolvhba0

4) Finding LUNs on your vHBA

4.1) Utilizing LUN's from a vHBA created by the storage pool

Assuming that a storage pool was created for a vHBA, use the command
"virsh vol-list" command in order to generate a list of available
LUN's
on the vHBA, as follows:

# virsh vol-list poolvhba0 --details
Name Path
---------------------------------------------------------------------

unit:0:2:0 
/dev/disk/by-path/pci-0000:04:00.1-fc-0x203500a0b85ad1d7-lun-0 block

The list of LUN names displayed will be available for use as disk volumes
in virtual machine configurations.

4.2) Utilizing LUN's from a vHBA created using the node device driver

Finding an available LUN from a vHBA created using the node device driver
can be achieved either via use of the "virsh nodedev-list" command or
through manual searching of the hosts system file system.

Use the "virsh nodedev-list --tree | more" and find the parent HBA
to which the vHBA was configured. The following example lists the
pertinent part of the tree for the example HBA "scsi_host5":

+- scsi_host5
|
+- scsi_host7
+- scsi_target5_0_0
| |
| +- scsi_5_0_0_0
|
+- scsi_target5_0_1
| |
| +- scsi_5_0_1_0
|
+- scsi_target5_0_2
| |
| +- scsi_5_0_2_0
| |
| +- block_sdb_3600a0b80005adb0b0000ab2d4cae9254
|
+- scsi_target5_0_3
|
+- scsi_5_0_3_0

The "block_" indicates it's a block device, the "sdb_"
is a
convention to signify the the short device path of "/dev/sdb", and the
short device path or the number can be used to search the
"/dev/disk/by-{id,path,uuid,label}/" name space for the specific LUN
by name, for example:

# ls /dev/disk/by-id/ | grep 3600a0b80005adb0b0000ab2d4cae9254
scsi-3600a0b80005adb0b0000ab2d4cae9254

# ls /dev/disk/by-path/ -l | grep sdb
lrwxrwxrwx. 1 root root 9 Sep 16 05:58 
pci-0000:04:00.1-fc-0x203500a0b85ad1d7-lun-0 -> ../../sdb

As an option to using "virsh nodedev-list", it is possible to manually
iterate through the "/sys/bus/scsi/device" and
"/dev/disk/by-path"
directory trees in order to find a LUN using the following steps:

1. Iterate over all the directories beginning with the SCSI host number
of the vHBA under the "/sys/bus/scsi/devices" tree. For example, if
the
SCSI host number is 6, the command would be:

# ls /sys/bus/scsi/devices/6:* -d
/sys/bus/scsi/devices/6:0:0:0 /sys/bus/scsi/devices/6:0:1:0
/sys/bus/scsi/devices/6:0:2:0 /sys/bus/scsi/devices/6:0:3:0

2. List the "block" names of all the entries belongs to the SCSI host
as follows:

# ls /sys/bus/scsi/devices/6:*/block/
/sys/bus/scsi/devices/6:0:2:0/block/:
sdc
/sys/bus/scsi/devices/6:0:3:0/block/:
sdd

This indicates that "scsi_host6" has two LUNs, one is attached to
"6:0:2:0", with the short device name "sdc", and the other
is attached
to "6:0:3:0", with the short device name "sdd".

3. Determine the stable path to the LUN.

Unfortunately a device name such as "sdc" is not stable enough for use
by libvirt. In order to get the stable path, use the "ls -l 
/dev/disk/by-path"
and look for the "sdc" path:

# ls -l /dev/disk/by-path/ | grep sdc
lrwxrwxrwx. 1 root root 9 Sep 10 22:28 
pci-0000:08:00.1-fc-0x205800a4085a3127-lun-0 -> ../../sdc

Thus "/dev/disk/by-path/pci-0000:08:00.1-fc-0x205800a4085a3127-lun-0"
is the stable path of the LUN attached to address "6:0:2:0" and will
be
used in virtual machine configurations.

5) Virtual machine configuration change to use vHBA LUN

Adding the vHBA LUN to the virtual machine configuration is done via
an XML modification to the virtual machine.

5.1) Using a LUN from a vHBA created by the storage pool

Adding the vHBA LUN to the virtual machine is handled via XML to create
a disk volume on the virtual machine with the following example XML:

<disk type='volume' device='disk'>
<driver name='qemu' type='raw'/>
<source pool='poolvhba0' volume='unit:0:2:0'/>
<target dev='hda' bus='ide'/>
</disk>

In particular note the usage of the "<source>" directive with
the "pool"
and "volume" attributes listing the storage pool and the short volume
name.

5.2) Using a LUN from a vHBA created using the node device driver

Configuring a vHBA on the virtual machine can be done with its
stable path (path of {by-id|by-path|by-uuid|by-label}). The following is an
XML example of a direct LUN path:

<disk type='volume' device='disk'>
<driver name='qemu' type='raw'/>
<source 
dev='/dev/disk/by-path/pci-0000\:04\:00.1-fc-0x203400a0b85ad1d7-lun-0'/>
<target dev='sda' bus='scsi'/>
</disk>

NOTE: The use of "device='disk'" and the long
"<source>" device name.
The example uses the "by-path" option. The backslashes prior to the
colons are required, since colons can be considered as delimiters.

5.3) To configure the LUN as a pass-through device, use the following XML
examples.

For a vHBA created using the node device driver:

<disk type='volume' device='lun'>
<driver name='qemu' type='raw'/>
<source 
dev='/dev/disk/by-path/pci-0000\:04\:00.1-fc-0x203400a0b85ad1d7-lun-0'/>
<target dev='sda' bus='scsi'/>
</disk>

NOTE: The use of "device='lun'" and again the long
"<source>" device
name. Again, the backslashes prior to the colons are required.

For a vHBA created by a storage pool:

<disk type='volume' device='disk'>
<driver name='qemu' type='raw'/>
<source pool='poolvhba0' volume='unit:0:2:0'/>
<target dev='hda' bus='ide'/>
</disk>

Although it is possible to use the LUN's path as the disk source for a
vHBA created by the storage pool, it is recommended to use libvirt storage
pool and storage volume instead.

6) Destroying a vHBA

A vHBA created by the storage pool can be destroyed by the virsh command
"pool-destroy", for example:

# virsh pool-destroy poolvhba0

NOTE: If the storage pool is persistent, the vHBA will also be removed
by libvirt when it destroys the storage pool.

A vHBA created using the node device driver can be destroyed by the
command "virsh nodedev-destroy", for example (assuming that scsi_host6
was created as shown earlier):

# virsh nodedev-destroy scsi_host6

Destroying a vHBA removes it just as a reboot would do since the node
device driver does not support persistent configurations.

7) Troubleshooting

7.1) Discovery of HBA capable of NPIV prior to 1.0.4

Prior to libvirt 1.0.4, discovery of HBAs capable of NPIV
requires checking each of the HBAs on the host for the capability flag
"vport_ops", as follows:

First you need to find out all the HBA by capability flag "scsi_host":

# virsh nodedev-list --cap scsi_host
scsi_host0
scsi_host1
scsi_host2
scsi_host3
scsi_host4
scsi_host5

Now check each HBA to find one with the "vport_ops" capability, either
one at a time as follows:

# virsh nodedev-dumpxml scsi_host3
<device>
<name>scsi_host3</name>
<parent>pci_0000_00_08_0</parent>
<capability type='scsi_host'>
<host>3</host>
</capability>
</device>

That says "scsi_host3" doesn't support vHBA

# virsh nodedev-dumpxml scsi_host5
<device>
<name>scsi_host5</name>
<parent>pci_0000_04_00_1</parent>
<capability type='scsi_host'>
<host>5</host>
<capability type='fc_host'>
<wwnn>2001001b32a9da4e</wwnn>
<wwpn>2101001b32a9da4e</wwpn>
<fabric_wwn>2001000dec9877c1</fabric_wwn>
</capability>
<capability type='vport_ops' />
</capability>
</device>

But "scsi_host5" supports it.

NOTE: In addition to libvirt 1.0.4 automating the lookup of HBA's capable
of supporting a vHBA configuration, the XML tags "max_vports" and
"vports"
will describe the maximum vports allowed and the current vports in use.

As an alternative and smarter way, you can avoid above cumbersome steps
by simple script like:

for i in $(virsh nodedev-list --cap scsi_host); do
if virsh nodedev-dumpxml $i | grep vport_ops > /dev/null; then
echo $i;
fi
done

NOTE: It is possible that node device is named
"pci_10df_fe00_scsi_host_0".
This is because libvirt supports two backends for the node device driver
("udev" and "HAL"), but they lead to completely different
naming styles.
The udev backend is preferred over the HAL backend since HAL support
is in maintenance mode. The udev backend is more common; however, if
your destribution packager built the libvirt binaries without the
udev backend, then the more complicated names such as
"pci_10df_fe00_scsi_host_0" must be used.

7.2) Creation of a vHBA using the node device driver prior to 0.9.10

For libvirt prior to 0.9.10, you will need to specify the "wwnn" and
"wwpn"
manually when creating a vHBA, example XML as follows:

<device>
<name>scsi_host6</name>
<parent>scsi_host5</parent>
<capability type='scsi_host'>
<capability type='fc_host'>
<wwnn>2001001b32a9da5e</wwnn>
<wwpn>2101001b32a9da5e</wwpn>
</capability>
</capability>
</device>

7.3) Creation of storage pool based on vHBA prior to 1.0.5

Prior to libvirt 1.0.5, one can define a "scsi" type pool based on a
vHBA by it's SCSI host name (e.g. "host5" in XML below), using an
example
XML as follows:

<pool type='scsi'>
<name>poolhba0</name>
<uuid>e9392370-2917-565e-692b-d057f46512d6</uuid>
<capacity unit='bytes'>0</capacity>
<allocation unit='bytes'>0</allocation>
<available unit='bytes'>0</available>
<source>
<adapter name='host0'/>
</source>
<target>
<path>/dev/disk/by-path</path>
<permissions>
<mode>0700</mode>
<owner>0</owner>
<group>0</group>
</permissions>
</target>
</pool>

There are two disadvantage of using the SCSI host name as the source
adapter. First the SCSI host number is not stable, thus it may cause trouble
for your storage pool after a system reboot. Second, the adapter name
(e.g. "host5") is not consistent with node device name (e.g.
"scsi_host5").

Moreover, using the SCSI host name as the source adapter doesn't
allow you to create a vHBA.

NOTE: Since 1.0.5, the source adapter name was changed to be consistent
with node device name, thus the second disadvantage is destroyed.

Regards,
Osier

On 18/09/13 18:39, Osier Yang wrote:
> Thanks for John Ferlan's lots of internal feedbacks, I believe it's
more
> readable, and better orgnized now. Should we create a page for it
> under http://libvirt.org/deployment.html or add it in WIKI?
>
> =========================================
Err, the indentions are broken in the mail body. So I attached it here.